Materials Science and Engineering Commons^™

Displacement Damage Effects In Gesn Light Emitting Diodes, Kevin K. Choe

Theses and Dissertations

Potential future use on Earth-orbiting satellites calls for investigation into the suitability of GeSn based photonic devices in high energy proton environments. The electroluminescence (EL) intensity of Ge1-xSnx (x = 0, 0.02, 0.069, and 0.094) light emitting diodes was measured before and after irradiation by 2 MeV protons at relatively high fluence levels. The results showed that GeSn devices with higher Sn content were up to 10 times more resistant against proton displacement damage than the pure Ge (x = 0) devices. As Sn concentration increased, the band gap decreased, and V-P hole trap energy level moved further from the …

Improved Fabrication For Micromirror Arrays, Enoc Flores

Theses and Dissertations

Micromirror devices which consisted of one SU-8 2050 layer, two different exposures, and a series of metal depositions were constructed and evaluated. By varying the exposure, a micromirror structure was fabricated with different thicknesses, a ratio of 1.083 µm/(mJ/cm2) was found. The initial design consisted of four layers. The pillar was made of one SU-8 layer, and the top portion had three layers in the following order: gold, SU-8, and gold. This design could not be released and did not have characteristics of a flat and conformal reflective surface. Several variations of the initial design were explored and all of …

Characterization Of Metal Contacts On Hydrothermally Synthesized Uranium Dioxide For Novel Semiconductor Applications, Tory E. Robinson

Theses and Dissertations

This research is focused on determining which metals or combinations of metals form effective electrical contacts on hydrothermally synthesized UO2 substrates to allow for additional work in characterization of the material as well as the feasibility of its use in semiconductor devices such as solid-state neutron detectors. A methodology was established for selection of candidate metals. Target mixtures composed of Au, Ag, Pt, and Mg were chosen along with several single-metals. Thin metal films were deposited onto tungsten probe tips and hydrothermally synthesized UO2 samples to allow for analysis of mechanical and deposited contact to the substrates through I-V measurements.

Evaluation Of Guar Gum As A Novel Adsorbent, Philicia Geiser

Theses and Dissertations

Guar gum (GG) is a promising product increasingly used in a variety of industries. It is nontoxic, inexpensive, and biodegradable. This research evaluated novel approaches using GG as an adsorbent for aromatic organic water contaminants. The application of GG demonstrated some effectiveness against all contaminants tested. Two brands of GG were tested using 5 different GG treatment strategies. Various experiments demonstrated nearly complete removal of Allura Red dye, Brilliant Blue dye, Erythrosine B dye, Methylene Blue dye, Tartrazine dye, and 2,4-dinitrotoluene; additionally, 78% adsorption was observed for Fast Green dye. GG typically removed less than 10% of toluene, which rapidly …

Creep Of Nextel 720/Alumina Ceramic Matrix Composite With Diamond-Drilled Effusion Holes At 1200°C In Air And In Steam, Megan L. Harkins

Theses and Dissertations

A recent study evaluated tensile stress-strain and tensile creep behavior of an oxide-oxide composite (Nextel™720/alumina) with laser-drilled effusion holes at 1200°C. It was determined that the presence of laser-drilled holes degraded the mechanical properties and performance of the CMC as a result of damage caused to the composite microstructure by the laser drilling process. Based on these results, the present effort sought to assess the effects of diamond-drilled holes on the mechanical behavior of this CMC. Tensile properties of the N720/A composite at 1200°C in laboratory air were unaffected by the presence of an array of 17 diamond-drilled effusion holes. …

Scaling Film Cooling Adiabatic Effectiveness With Mass Transfer And Thermal Experimental Techniques, Luke J. Mcnamara

Theses and Dissertations

With increasing engine temperatures, it is becoming more important to design effective film cooling schemes. Low temperature, large scale tests are often implemented in the design process to reduce cost and complexity. A nondimensional adiabatic effectiveness can be used as an indication of the performance of a film cooling scheme. However, the coolant flow rate must be properly scaled between the low temperature tests and engine temperatures to accurately predict film cooling effectiveness. This process is complicated by gas property variation with temperature. Tests are commonly conducted using thermal measurement techniques with infrared thermography (IR), but the use of pressure …

Analysis And Design Of Modular Overhead Protection System Utilizing Readily Available Materials, Zachary J. Spranger

Theses and Dissertations

This research investigated passive overhead protective measures for existing facilities in an urban environment that are vulnerable to enemy munitions fire. A new modular structural system was designed utilizing commercially available construction material consisting of structural tubing, scaffolding clamps, base plates, and simple roofing components. Structural analysis software was used to model nine modular structures to understand the relationship between the load bearing capacity of the structural members and overall dimensions of the system. Environmental variables for the models were set to the Parwan Province in Afghanistan; this region presents worst-case scenarios both for environmental factors and threat of enemy …

Direct Numerical Simulation Of Roughness Induced Hypersonic Boundary Layer Transition On A 7° Half-Angle Cone, Tara E. Crouch

Theses and Dissertations

Direct numerical simulation (DNS) computational fluid dynamic (CFD) calculations were performed on a 30° slice of 7° half-angle cones with increasing nose radii bluntness at Mach 10 while simulating a distributed roughness pattern on the cone surface. These DNS computations were designed to determine if the non-modal transition behavior observed in testing performed at the Arnold Engineering Development Center (AEDC) Hypervelocity Wind Tunnel 9 was induced via distributed surface roughness. When boundary layer transition is dominated by second mode instabilities, an increase in nose radius delays the transition location downstream. However, blunt nose experiments indicated that as the nose radius …

Interlaminar Shear Performance Of High Temperature Composites, Tyler A. Wallis

Theses and Dissertations

Interlaminar shear properties of a high temperature polymer matrix composite (HTPMC) and a ceramic matrix composite (CMC) were evaluated at elevated tempera- ture. Two variants of the HTPMC were studied. Both consisted of a high-temperature polyimide (AFR-PE-4) matrix reinforced with Astroquartz-III pre-impregnated glass fabric woven in an eight-harness-satin weave. The first HTPMC variant also contained stainless steel foil at the midplane, while the second HTPMC variant did not. The interlaminar shear strength (ILSS) of both variants of the HTPMC was evaluated at 204°C in laboratory air. The addition of the stainless steel foil resulted in significant loss of ILSS for …

Ballistic Evaluation Of Carbon Nanotube Sheet Material In Multifunctional Applications, Casey M. Keilbarth

Theses and Dissertations

Significant development of carbon nanotubes has occurred since they were first studied in the 1990's. Attempts to capture the phenomenal molecular properties in practical applications are gaining ground as new methods of producing CNTs have been developed. This thesis sought to determine if the addition of commercially produced CNT sheets to thin carbon fiber panels improved the ballistic properties of the panel. The difference between 0 and 4 CNT sheets was studied. The hypothesis was that inte- grating CNT sheets into the laminate would increase the projectile energy absorbed by the panel and reduce the damage to the panel incurred …

Process Parameter Development Of Additively Manufactured Af9628 Weapons Steel, Erin M. Hager

Theses and Dissertations

The manufacture of components in Additive Manufacturing processes is limited by the range of materials available. Qualification of materials for Additive Manufacturing is time intensive, and is often specific to a single type of machine. In this study, an approach to selecting power, speed, and hatch spacing values for a newly powderized material, AF9628 weapons steel, is described that results in highly dense (>99.9%) parts on an MLab 200R Cusing. Initial power and speed values used in a weld track study were selected based on a survey of parameters used on similar materials, with a focus on the energy …

Computational And Experimental Development Of 2d Anisotropic Photonic Crystal Metamaterials, James A. Ethridge

Theses and Dissertations

The future of optical devices involves manipulation of nanoscale structure in order to achieve full control over the properties of the device. In fields as diverse as directed energy, remote sensing, optical communications and optical computing, these devices promise to greatly improve performance and efficiency. To advance this further, novel samples that incorporate both photonic crystal (PhC) structure and metamaterial properties, known as PhC metamaterials, are proposed. These PhC metamaterials allow for complete control over the directionality of the light-matter interaction to serve in these new applications. To develop this technology, first, metamaterials with no PhC structure are fabricated using …

Engineering Magnetic Properties Of Nanoparticles For Biomedical Applications And Magnetic Thin Film Composite Heterostructures For Device Applications., Shivakumar Hunagund

Theses and Dissertations

The motivation of this study is to investigate the size dependent properties of Gadolinium silicide nanoparticles and their potential applications in Biomedicine. We use two approaches in our investigation - size dependence and possible exchange interaction in a core-shell structure. Past results showed Gd₅Si₄ NPs exhibit significantly reduced echo time compared to superparamagnetic iron oxide nanoparticles (SPION) when measured in a 7 T magnetic resonance imaging (MRI) system. This indicates potential use of Gd₅Si₄ ferromagnetic nanoparticles as T2 contrast agents for MRI.

Until recently most contrast agents (CA) that are used in Magnetic Resonance …

Modeling The Peak Absorption Of Meh-Ppv In Various Solvents Using Density Functional Theory, Corell H. Moore

Theses and Dissertations

Density Functional Theory (DFT) and time-dependent Density Functional Theory (TD-DFT) are powerful tools for modeling orbital energy in conjugated molecules and have been useful tools for research in organic photovoltaics. In this work, DFT is first used to explain the red shift in the absorption spectrum and increased absorption observed in MEH-PPV. Initially, the modeling of the red-shift in the absorption peak of MEH-PPV is studied using Gaussian 03 software with the global hybrid functional B3LYP for exchange-correlation and the 6-31G basis set. DFT and TD-DFT are used to separately study the effects of polymer chain length, carbon-carbon double-bond stretching, …

Metallic Systems At The Nano And Micro Scale: Bimetallic Nanoparticles As Catalysts And Mcraly Bond Coats In Thermal Barrier Coatings, Kenneth Kane

Theses and Dissertations

The dissertation is split into two parts. The first part will be focused on changes in material properties found at the nanoscale, as miscibility and electronic structure can change significantly with size. The formation of classically-immiscible bimetallic nanoparticles (BNPs) becomes favorable at the nanoscale and novel catalytic properties can emerge from the bimetallic alloying. The formation of alloyed and non-alloyed BNPs is achieved through pulse laser ablation (PLA) and a significant increase in catalytic activity is observed for both. Recently discovered, the increased activity in the non-alloyed BNPs, deemed multicomponent photocatalysis, is examined and the proposed mechanism discussed. The second …

Compositional Analysis Of Cerium And Cesium In Rapid Setting Cement As An Immobilization Agent For Nuclear Waste, Riyadh M. Motny

Theses and Dissertations

A feasibility of rapid setting cement (RSC) as an agent of immobilization for certain elements such as fission products or radioactive materials was explored. Cerium (Ce) and cesium (Cs) have been selected as a surrogate for U and/or Pu and fission products, respectively, in this study in three phases. In Phase I, RSC was evaluated for physical properties (e.g., porosity, density, pH values, etc.) using two groups methods—the cement powder at different concentrations of Ce (2 – 10 wt%) with deionized water (DIW) and artificial seawater (ASW). The results showed that the final setting time and compressive strength of RSC …

Au@Tio2 Nanocomposites Synthesized By X-Ray Radiolysis As Potential Radiosensitizers, Maria C. Molina Higgins

Theses and Dissertations

Radiosensitization is a novel targeted therapy strategy where chemical compounds are being explored to enhance the sensitivity of the tissue to the effects of ionizing radiation. Among the different radiosensitizers alternatives, nanomaterials have shown promising results by enhancing tumor injury through the production of free radicals and reactive oxygen species (ROS). In this work, Gold-supported titania (Au@TiO₂) nanocomposites were synthesized through an innovative strategy using X-ray irradiation, and their potential as radiosensitizers was investigated. Radiosensitization of Au@TiO₂ nanocomposites was assessed by monitoring the decomposition of Methylene Blue (MB) under X-ray irradiation in the presence of the nanomaterial. …

The Fabrication And Characterization Of Cu(In,Ga)Se2 Solar Cell, Yasir Al-Rikabi

Theses and Dissertations

The extremely large energy consumption rate on Earth today is likely to exhaust the conventional energy resources such as fossil fuels and coal in the near future. The need for new renewable energy sources becomes inevitable and urgent. Among various new energy resources, solar energy is the most promising one because it is abundant and environmentally clean. The Sun light can be converted into electricity by using solar cell devices. Even though the solar cell panels made of thin films are in competition with conventional single crystal solar cells, only four thin film solar cells, i.e. amorphous silicon (a- Si), …

High Performance Glad Nanorod Cuinxga(1-X)Se2 Arrays With Enhanced Carrier Collection And Light Trapping For Photodetector Applications, Matthew P. Brozak

Theses and Dissertations

Nanostructured arrays have become an appealing alternative to their thin film and bulk counterparts in photovoltaic and photoconductivity applications. Thin films have recently continued the evolution of efficiency and material sciences after taking over from traditional, doped silicon devices. Inside of the thin film revolution, CuInxGa(1-x)Se2 (CIGS) has emerged as a high efficiency p-type semiconductor with a wide band gap that is tunable based on the Indium to Gallium ratio and often deposited via expensive, high temperature deposition methods. While each of the aforementioned methods of construction have their disadvantages, the advantages of each can be combined to potentially increase …

Non-Destructive Characterization Of Rotated Uniaxial Anisotropic Materials, Alexander G. Knisely

Theses and Dissertations

Electromagnetic material characterization of anisotropic media requires measurement diversity, minimal measurement uncertainty and insight into sample symmetry. Additionally, non-destructive characterization techniques are valued over legacy measurement techniques because a destructive approach requires sample preparation to execute a measurement. A Single Port Waveguide Probe (SPWP) non-destructive material characterization technique is proposed to accommodate measuring a metal backed, known thickness, rotated uniaxial anisotropic material. A rotated uniaxial sample possesses unique transverse constitutive components and a longitudinal constitutive component which is the same as one of the transverse values. The SPWP consists of a rectangular waveguide aperture cut in the center of a …

Design And Characterization Of Polymer Nanocomposites For Engineering Applications, Joseph Richard Nalbach

Theses and Dissertations

Polymer nanocomposites represent an area of materials that can yield useful properties not achievable in bulk materials. Not only can they have such properties but also they can be relatively easy to generate. With dwindling fossil fuels there is an increased need for both new methods to harvest energy and to transport the captured energy more effectively. Two separate nanocomposite materials are created to support this work with dramatically different properties, both to aid in energy efficiency. The first is an energy harvesting foam to fully utilize the structural deformability of such a material. A dissolvable sugar scaffold is combined …

Creep Of Hi-Nicalon™ S Ceramic Fiber Tows At 1100°C In Air And In Silicic Acid-Saturated Steam, Logan M. Gumucio

Theses and Dissertations

Innovations in SiC based ceramic matrix composites (CMCs) have yielded exceptional high-temperature properties and performance in aggressive oxidizing environments. These material characteristics provide potential avenues for future advancements in many applications where current metallic alloys perform near their operating temperature limits in a harsh environment. As steam (typically present in these environments) enters through cracks in the matrix of a SiC/SiC composite, it leaches Si and becomes saturated with silicic acid, Si(OH)₄, prior to attacking the reinforcing SiC fibers. Therefore, it is paramount that a thorough understanding of the performance and durability of SiC fibers be obtained under …

Perovskite Solar Cells Fabricated Via Scalable Dip Coating Methods, Joseph F. Iannello

Theses and Dissertations

Perovskite solar cells present the possibility for less expensive electricity generation, through the use of low cost materials and fabrication methods relative to current silicon-based technology. Many current methods of fabricating thin film perovskite solar cells focus on spin-coating, which inherently lacks scalability due to particle conglomeration, poor uniformity over a larger area, and safety concerns. Dip-coating, an alternative to spin-coating, which is explored here addresses these issues which limit scalability. Each individual layer can be separately synthesized, deposited, and characterized, which leads towards scalability. Choosing only the best results from each independent layer allowed progress to the creation of …

Tensile Properties And Fatigue Behavior Of Geopolymer Matrix Composites With Carbon Fiber Reinforcement At Elevated Temperature, Steffan M.L. Wilcox

Theses and Dissertations

The tensile stress-strain and tension-tension fatigue of geopolymer matrix composites reinforced with 0/90 carbon fibers was investigated at 23 and 300°C in laboratory air. Geopolymers are inorganic polymeric materials composed of alumina, silica, and alkali metal oxides. Because geopolymers are synthesized as a fluid mixture or particles and liquid, they can be cast into a desired shape, and cured at only slightly elevated temperatures. The relative ease of synthesis and low processing temperatures make geopolymers an attractive choice as a matrix material for composite materials. Geopolymers also offer resistance to heat and oxidizing environments. Currently, geopolymer matrix composites are being …

Creep Of Hafnium Diboride -20 Vol% Silicon Carbide At 1500°C In Air, Glen E. Pry

Theses and Dissertations

Refractory metal borides, commonly referred to as Ultra High Temperature Ceramics (UHTCs), exhibit a number of unique properties, such as extremely high melting temperature and hardness, chemical stability, high electrical and thermal conductivity and corrosion resistance. It has been demonstrated that the addition of SiC improves the oxidation resistance of ZrB2- and HfB2-based UHTCs above 1200°C by modifying the composition of the oxide scale. Addition of SiC retards the oxidation rate of ZrB2 and HfB2 by forming a protective layer of borosilicate glass. Creep deformation is one of the critical criterion for structural application of ceramics at elevated temperatures. Compression …

A System Dynamics Innovation Diffusion Model Applied To Carbon Nanotube Manufacturing, Frances G. Mackinnon

Theses and Dissertations

The transition of advanced technologies from their nascent state to viable commercial entities is a critical step in assuring the United States' national technological superiority and support is often required to incubate such technological developments. We propose a spiral development to investigate the possible scenarios, underlying economics, and risk associated with scaling up carbon nanotube (CNT) production to a commercially viable scale. As the first stage of this proposed effort, this study characterizes the potential scenarios by which a CNT manufacturing company can generate positive annual net revenue and potentially be considered a competitive manufacturer of CNT products on an …

Creep Of Hi-Nicalon™ S Ceramic Fiber Tows At 1000°C In Air And In Silicic Acid-Saturated Steam, Brian G. Kroeger

Theses and Dissertations

Advanced SiC/SiC ceramic matrix composites (CMCs) are being considered for a variety of applications. Of interest is their ability to withstand exposure to high temperature in an aggressive oxidizing environment. The presence of steam creates such an environment. As steam traverses across a SiC/SiC composite and through cracks in the SiC matrix, it becomes saturated with silicic acid, Si(OH)₄. It is essential to understand the long-term impacts and durability of SiC/SiC CMCs that have been exposed to such a demanding environment. The present research investigated creep of Hi-Nicalon™ S SiC fibers at 1000°C in air and in silicic …

Material Thermal Property Estimation Of Fibrous Insulation: Heat Transfer Modeling And The Continuous Genetic Algorithm, Elora Frye

Theses and Dissertations

Material thermal properties are highly sought after to better understand the performance of a material under particular conditions. As new materials are created, their physical properties will determine their performance for various applications. These properties have been estimated using many techniques including experimental testing, numerical modeling, and a combination of both. Existing methods can be time consuming, thus, a time-efficient and precise method to estimate these thermal properties was desired. A one-dimensional finite difference numerical model was developed to replicate the heat transfer through an experimental apparatus. A combination of this numerical model and the Continuous Genetic Algorithm optimization technique …

Photoluminescence From Gan Co-Doped With C And Si, Mykhailo Vorobiov

Theses and Dissertations

This thesis devoted to the experimental studies of yellow and blue luminescence (YL and BL relatively) bands in Gallium Nitride samples doped with C and Si. The band BL_C was at first observed in the steady-state photoluminescence spectrum under high excitation intensities and discerned from BL1 and BL2 bands appearing in the same region of the spectrum. Using the time-resolved photoluminescence spectrum, we were able to determine the shape of the BL_C and its position at 2.87 eV. Internal quantum efficiency of the YL band was estimated to be 90\%. The hole capture coefficient of the BL_{C …}

Hydrophobicity Of Low Temperature Vibrating Surfaces, Christian Fergusson

Theses and Dissertations

This study proposes a method to enhance the anti-icing capabilities of superhydrophobic surfaces by utilizing vibration to further reduce contact time of an impacting droplet in addition to keeping the droplet in the Cassie-Baxter regime, where surface adhesion is lower than the opposing Wenzel regime. We tested this with two methods: by investigating the effects of vibration normal to the plane of a superhydrophobic surface being impacted by water droplets in a room temperature environment, with the surface horizontal in a room temperature environment and tiled in a subzero degree environment. The amplitude and frequency of the vibration were varied …