Materials Science and Engineering Commons^™

Urea Pre-Treatment Of N2-Annealed Transition Metal Oxides For Low Cost And Efficient Counter Electrodes In Dye-Sensitized Solar Cell, Hytham Elbohy

Electronic Theses and Dissertations

Photovoltaic cells have shown great promise as an alternative to fossil fuel-based energy sources. Dye-sensitized solar cells (DSSCs) have shown potential as low-cost replacement to silicon solar cells owing to their reduced material costs and simple fabrication techniques. Platinum (Pt) was used as a catalyst in the counter electrode for DSSCs. Metal oxides have been used as an alternative material to Pt. The introduction of oxygen vacancies inside metal oxides helps to facilitate electron transport to the electrolyte to enhance the reduction process of triiodide ions. Annealing n-type metal oxides under a reducing agent gas such as hydrogen (H2) at …

Computation Aided Design Of Multicomponent Refractory Alloys With A Focus On Mechanical Properties, Paul Daniel Clark

Electronic Theses and Dissertations

Quantum mechanical calculations paired with exponential growth in computer processing speed has created a paradigm shift in materials discovery. Simulations can be carried out to accurately predict structure-composition-property relationships of novel systems. This work focuses on calculating elastic properties of high entropy alloys, a new class of alloys that are built from 4+ elements in equi-atomic proportion. These alloys often exhibit simple microstructures and each constituent element contributes its properties to the overall bulk properties of the amalgamated material. This "cocktail" effect has led to the discovery of many alloys which could drive technical advances in the future. Elastic properties …

Stress-Induced Phase Change Sintering: A Novel Approach To The Fabrication Of Barium Chloride Transparent Ceramic Scintillators, William Shoulders

Electronic Theses and Dissertations

For the precise in-field identification of dangerous radioisotopes, the desire for higher resolution, cheaper, and more rugged gamma-ray scintillator detectors has pushed the materials science community to investigate new compounds and processing techniques.  One particular solution is Eu:BaCl2 transparent ceramics processed by the novel phase-change sintering technique. Typically, optical transparency in BaCl2 would be limited by birefringence scattering at grain boundaries due to mismatch in refractive index. Traditional ceramic processing routes would also predispose this volatile and hygroscopic material to the formation of defects, which interrupt the energy transfer in the scintillation process. Literature shows that these challenges have prevented …

Interdiffusion, Crystallography And Mechanical Properties Of Nickel Manganese Gallium Alloys, Le Zhou

Electronic Theses and Dissertations

NiMnGa Heusler alloys, functioning as either ferromagnetic shape memory alloys or mangetocaloric materials, have both practical applications and fundamental research value. The functional properties of NiMnGa alloys are closely related to the martensitic transformation from high temperature austenitic phase to low temperature martensitic phase. Alloys can be used for room temperature or high temperature applications, depending on the martensitic transformation temperature, which is compositional sensitive. The microstructure and crystallography of the martensites can be very complex but are crucial to the optimization of the material performance. In this study, for the first time, a combinatorial study by combining solid-to-solid diffusion …

Nanoengineered Energy Harvesting And Storage Devices, Chao Li

Electronic Theses and Dissertations

Organic and perovskite solar cells have recently attracted significant attention due to its flexibility, ease of fabrication and excellent performance. In order to realize even better performance for organic and perovskite solar cells, rejuvenated effort towards developing nanostructured electrodes and high quality active layer is necessary. In this dissertation, several strategic directions of enhancing the performance of organic and perovskite solar cells are investigated. An introduction and background of organic and perovskite solar cells, which includes motivation, classification and working principles, nanostructured electrode materials and solvent effect on active materials, and devices fabrication, are presented. A facile method, called Spin-on …

Electrical Properties Of Polymer-Derived Silicoaluminum Carboxide Ceramics (Sialco) And Their Applications In Micro-Sensors, Yejie Cao

Electronic Theses and Dissertations

Polymer-derived ceramic (PDC) is a new kind of material which is directly synthesized by the thermal decomposition of polymer precursors. Due to their unique structure, which consists of the amorphous matrix phase and free-carbon phase, PDCs exhibit many distinguished properties even at high-temperature environment such as oxidation and creep resistance, amorphous semiconducting behavior as well as piezoresistive behavior. These outstanding properties make PDCs become promising candidates for various applications especially for high-temperature microsensors. However, most common used PDCs in the market now are SiC, SiCN and Si(M)CN ceramics, the high price and toxicity of their raw materials as well as …

Synthesis And Characterization Of Stable And Metastable Phases In Ni- And Fe-Based Alloy Systems By Mechanical Alloying, Ahmed Al-Joubori

Electronic Theses and Dissertations

Mechanical Alloying (MA) is a process that involves repeated cold welding, fracturing and rewelding of powder particles in a high-energy ball mill and has been used extensively to synthesize both stable (equilibrium) and metastable phases in a number of alloy systems. This is due to its ability to achieve many effects simultaneously, viz., reduction in grain size, introduction of a variety of crystal defects, disordering of the lattice, and modifying the crystal structures of materials; all these allowing alloying and phase transformations to occur in powders. In this Dissertation, we have synthesized a number of different alloy phases in Ni- …

A Study Of Crystallization Behavior In Phase Separated Chalcogenide Glasses, Andrew Buff

Electronic Theses and Dissertations

Chalcogenide glasses (ChG) are known for their wide transmission ranges in the infrared and for their high refractive indices. However, applications for ChG are often limited by their poor thermal/mechanical properties. Precipitating a secondary crystalline phase in the glass matrix can improve these properties, but too much crystallization and/or large or multiple phase crystallites can lead to a loss in infrared (IR) transmission. Controlled crystallization can be used to tune the properties of these glasses. This work examines the crystallization behavior in phase separated chalcogenide glasses in the GeSe2-As2Se3-PbSe glass system. Specifically, the research presented in this thesis work has …

Fabrication And Investigation Of An Enzyme-Free, Nanoparticle-Based Biosensor For Hydrogen Peroxide Determination, Craig Neal

Electronic Theses and Dissertations

Electrochemical biosensors often employ enzymes as detection elements. These sensors are highly selective towards target analytes, however the scope of their application is limited by the poor stability of the enzyme. In this study, multi-valent inorganic cerium oxide nanoparticles were used as detection elements for the analysis of hydrogen peroxide. The electrochemical response of the cerium oxide towards hydrogen peroxide analyte is defined through cyclic voltammetry and chronoamperometry. This response was found to be dependent on nanoparticle Ce3+:Ce4+ redox state ratio and this property is exploited to fabricate a biosensor. As produced, the biosensor demonstrated sensitivity at picomolar analyte concentrations. …

Effect Of Poisson’S Ratio On Material Properties Characterization By Nanoindentation With A Cylindrical Flat Tip Indenter, Md Mehadi Hassan

Electronic Theses and Dissertations

Nano indentation technology is commonly used to determine the mechanical properties of different kinds of engineering materials. The young’s modulus of the materials can be calculated with the load depth data obtained from an indentation test with a known Poisson’s ratio. In this investigation the NANOVEA micro/nanoindentation tester with a cylindrical flat-tip indenter will be used to find the elastic modulus, hardness and Pile up. Low carbon steel AISI1018, alloy steel AISI 4340 and aluminum alloy 6061 were selected for the case study. Finite element (FE) analysis using axisymmetric 3-D models used to establish the relationship between Poisson’s ratio and …

Spare Parts On Demand Using Additive Manufacturing : A Simulation Model For Cost Evaluation., Stefan Jedeck

Electronic Theses and Dissertations

Little is known about the impact of additive manufacturing in the spare part supply chain. A few studies are available, but they focus on specific parts and their applications only. A general model, which can be adapted to different applications, is nonexistent. This dissertation proposes a decision making framework that enables an interested practitioner/manager to decide whether using additive manufacturing to make spare parts on demand is economical when compared to conventional warehousing strategy. The framework consists of two major components: a general discrete event simulation model and a process of designing a wide range of simulation scenarios. The goal …

On Thermal Aging Prevention In Polymer Core Composite Conductor Rods, Joe D. Hoffman

Electronic Theses and Dissertations

Increased energy usage in the United States and worldwide is driving the demand for new technologies to transmit electrical power in greater quantities and with reliable, safe, and more efficient methods. One recent innovation is to replace the standard Aluminum Conductor Steel Reinforced electrical transmission conductor with a new conductor design that utilizes a fiber reinforced polymer core rod to support a fully annealed aluminum conductor. This new technology that includes a hybrid carbon fiber/epoxy and glass fiber/epoxy support core allows for better efficiency and for greater current to be transmitted in the same size and weight line. These new …

Nanoarchitectured Energy Storage Devices, Zenan Yu

Electronic Theses and Dissertations

Supercapacitors, the devices that connect the gap between batteries and conventional capacitors, have recently attracted significant attention due to their high specific capacitance, substantially enhanced power and energy densities, and extraordinary cycle life. In order to realize even better performance with supercapacitors, rejuvenated effort towards developing nanostructured electrodes is necessary. In this dissertation, several strategic directions of nanoarchitecturing the electrodes to enhance the performance of supercapacitors are investigated. An introduction and background of supercapacitors, which includes motivation, classification and working principles, recent nanostructured electrode materials studies, and devices fabrication, are initially presented. A facile method, called Spin-on Nanoprinting (SNAP), to …

Studies Related To Microbially Induced Corrosion Of Stainless Steel 304 And 316, Somil Gupta

Electronic Theses and Dissertations

Pitting corrosion of stainless steel (SS) is observed in many different industries including the dairy industry. It is of concern, because it weakens the steel, and can cause cracking. Any replacement or repair of SS equipment is very costly and also causes delays in product manufacture. Microbial Induced Corrosion (MIC) is a possible accelerator of natural corrosion seen in galvanized steel pipes. Studies have shown a correlation between surface roughness and the ability of bacteria to colonize and form biofilms. Dairy industry utilizes higher food grade SS 304 and 316. However, even these relatively corrosion resistant stainless steel grades may …

Adsorption Behaviour Of Polyacrylic Acid On Cerium Oxide Nanostructures: Experimental And Predictive Model, Ali Haghighat Mesbahi

Electronic Theses and Dissertations

Cerium oxide-based slurries are crucial for chemical mechanical polishing (CMP) in electronic industry. For these slurry systems, poly(acrylic acid) (PAA) is heavily utilized to provide colloidal stability. Some of the important parameters in the colloid stability are molecular weight (MW) and concentration of stabilizer, size of the nanoparticle in the slurry and the pH of system. By determining the colloidal stability of a discrete number of slurry formulations and relating these to certain slurry component parameters, a possible model can be produced to predict the influence of these parameters on the particle stability. Direct quantification of colloidal stability is difficult, …

Porosity Removal Of Cm247 Ni-Base Superalloy Using Thermal Heat Treatment Without Applied Pressure, Chad Heinrich

Electronic Theses and Dissertations

Blade and vane components made with Ni-base superalloys play a vital role in hot section of gas turbine engines. Removal of porosity in cast Ni-base superalloys is a critical process consideration since porosity from casting process can have deleterious effects on the performance and integrity of superalloy component. Still, the cost-efficient processing of Ni-base superalloys that are technologically acceptable, or superior, can contribute significantly to the life-cycle cost of gas turbine engines. The purpose of this thesis was to explore the possibility of eliminating the hot isostatic pressing cycle in a CM247 Ni-base superalloy processing. For cast CM247, conventional processing …

Phase Transformations And Microstructural Evolution In The U-10 Wt.% Mo Alloy With Various Zr Additions At 900c And 650c, Nicholas Eriksson

Electronic Theses and Dissertations

The Reduced Enrichment for Research and Test Reactor (RERTR) now known as the Material Minimization and Management Reactor Control program (MMMRC) seeks to replace the use of highly enriched uranium (HEU) fuels used in research and test nuclear reactors around the world. The low enriched uranium (LEU) fuels must have fissionable uranium densities comparable to the HEU fuels. After extensive investigation by various researchers around the world, the U-Mo alloys were selected as a promising candidate. The Mo alloyed with U allows for the stabilization of the face-centered cubic ?-U phase, which demonstrated favorable irradiation behavior. However, deleterious diffusional interaction …

Early-Age Hydration Studies Of Portland Cement, Fengjuan Liu

Electronic Theses and Dissertations

Our current knowledge on cement hydration during setting is based on the discrete observation of hydrated paste. An advanced micro/nano-level technique which can perform the in-situ observation on the continuous hydration of cement paste is demanded. In this study, Raman spectroscopy (RS) was chosen as such a method to continuously investigate wet pastes. The objective of this research is to explore the hydration process and microstructural development of fresh pastes with this technique. This research was conducted in three phases. First, the RS analysis was used to continuously observe the cement hydration from 20 minutes after mixing to 9 hours. …

The Development Of A Laminated Copolyester Electric Guitar, Addison S. Karnes

Electronic Theses and Dissertations

This thesis is an investigation of the fabrication and assembly methodologies employed in the development of a proof-of-principle prototype electric guitar composed of laminated copolyester. The objective of the project was to develop the processes and procedures to create an optimized physical and visual bond between layers to minimize vibratory dissipation, thus maximizing sustain. A high speed CNC router, abrasive waterjet, laser engraver-cutter, as well as various manual fabrication and assembly methods were investigated in the construction of the guitar prototypes. The lamination processes explored include low-temperature, heat-assisted pressure bonding, solvent and chemical welding, and contact adhesives. The project concluded …

Thermal And Structural Modeling Of Electrochromics On Glass, Mahesh B. Manandhar

Electronic Theses and Dissertations

Advanced glazing is a type of window glazing that interacts with the surrounding environment to change its thermal and optical properties to create a more comfortable and energy efficient indoor environment. Electrochromics are one type of such advanced glazing materials that change their properties in response to an externally applied voltage controllable by the user or by automation.

The effectiveness of electrochromics depends upon how well it can keep off extreme temperature conditions from outdoors all year round as well as how structurally stable it can remain at such conditions. This research investigates the use of COMSOL, a finite element …

Stress Corrosion Cracking In Polymer Matrix Glass Fiber Composites, Jonathan Kosak

Electronic Theses and Dissertations

With the use of Polymer Matrix Glass Fiber Composites ever expanding, understanding conditions that lead to failure before expected service life is of increasing importance. Stress Corrosion Cracking (SCC) has proven to be one such example of conditions found in use in high voltage transmission line applications that leads to brittle fracture of polymer matrix composites.

SCC has been proven to be the result of acid buildup on the lines due to corona discharges and water buildup. This acid leaches minerals from the fibers, leading to fracture at low loads and service life. In order to combat this problem, efforts …

Dynamic Materials And Devices For Controlling Solar Heat Gain In Buildings, David Alie

Electronic Theses and Dissertations

Modern technology and materials science, coupled with an understanding of our energy consumption patterns, allows for the opportunity to realize large-scale energy savings through the implementation of more efficient, adaptive technologies. More efficient heating and cooling of both commercial and residential buildings is a strong candidate for such advancements. Indeed, a significant portion of the annual US energy budget is devoted to the heating, ventilation, and air conditioning (HVAC) of commercial and residential buildings in order to maintain safe, comfortable internal environments.

Dynamic tint windows, both traditional electrochromic devices and reflective devices, are promising candidates to help in the effort …

Aging Of A Polymer Core Composite Conductor Under Combined Ozone And Temperature Conditions, James M. Middleton

Electronic Theses and Dissertations

The next generation High Temperature Low Sag Polymer Core Composite Conductors (HTLS PCCC) can experience harsh in-service environments including high temperature and highly concentrated ozone. In some extreme cases, it is possible that the conductors will experience temperatures of up to 180°C and ozone concentrations as high as 1% (10,000 ppm). Therefore, the primary goal of this research was to determine the most damaging aging conditions which could negatively affect the in-service life of the conductors. This included characterizing the aging in ozone and at high temperature of the HTLS PCCC hybrid composite rods and neat resin. It was found …

Degradation Of High Voltage Glass Fiber-Reinforced Polymer Matrix Composites By Aggressive Environmental Conditions, Tianyi Lu

Electronic Theses and Dissertations

Polymer matrix composites reinforced with either E glass or ECR glass fibers-reinforced are used in a variety of high voltage electrical applications because of their advantages like lower weight and cost. However, they can be damaged by aggressive in-service conditions such as high temperature, ultraviolet radiation, moisture, ozone and corrosive environments. Different degradation mechanisms can develop in high voltage PMCs under those extreme environments, which, in turn, can affect the long term structural durability of the composites. A set of PMCs reinforced with ECR-glass and E-glass fibers embedded in four different resins has been investigated in this study. In addition, …

Environmental Degradation Of Nano Enhanced Polymers In Low Earth Orbit, Mohammed Jaradat

Electronic Theses and Dissertations

No abstract provided.

Real Time Monitoring Of Cell-Nanoparticles Interaction And Tracking Internalization Process By Mechanical Probing Using Atomic Force Microscopy, Anh Ly

Electronic Theses and Dissertations

With extensive development of nanotechnology in last few years, scientists have discovered that nanoparticles (NPs) can be used as an efficient Drug Delivery System (DOS). In order to develop better NPs based drug delivery tool, it is imperative to understand the interaction between the NPs and the cell membrane. In our earlier studies, cerium oxide nanoparticles (CNPs) have been reported to have therapeutic properties, specifically against abnormalities associated with oxidative stress. Therefore, CNPs with different sizes and morphology were selected to understand the interaction with cell. We analyzed the mechanical property of human nasal septum tumor cells membranes using Atomic …

An Uncooled Mid-Wave Infrared Detector Based On Optical Response Of Laser-Doped Silicon Carbide., Geunsik Lim

Electronic Theses and Dissertations

This dissertation focuses on an uncooled Mid-Wave Infra-Red (MWIR) detector was developed by doping an n-type 4H-SiC with Ga using the laser doping technique. 4H-SiC is one of the polytypes of crystalline silicon carbide, a wide bandgap semiconductor. The dopant creates an energy level of 0.30 eV, which was confirmed by optical spectroscopy of the doped sample. This energy level corresponds to the MWIR wavelength of 4.21 µm. The detection mechanism is based on the photoexcitation of electrons by the photons of this wavelength absorbed in the semiconductor. This process modifies the electron density, which changes the refraction index and, …

Using Acoustic Emission Monitoring For Energy-Based Fatigue Life Prediction, Sepehr Nesaei

Electronic Theses and Dissertations

The study of fatigue and fracture mechanics is crucial to the health monitoring and overall safety of aerospace and civil structures. The materials used to manufacture these industry parts have inherent anomalies that eventually grow under cyclic loadings during regular operation. The ASTM and/or military testing guidelines used to analyze and qualify structures and materials for use are costly and time consuming. Therefore, any additional methods or knowledge that can be used to reduce the number of tests will be useful to the industry to avoid unnecessary costs. Acoustic emission (AE) monitoring is currently used in many applications to assess …

Electroplated Micro- And Nanoscale Structures For Emitters And Sensors, Xiaochen Wang

Electronic Theses and Dissertations

In the electroplating process, dissolved metal cations are reduced by electrical current to a form a coherent metal coating on an electrode. Therefore, electroplating is primarily applied to modify the surface properties of an object (e.g. abrasion and wear resistance, corrosion protection, lubricity, aesthetic qualities, etc.), but also be applied to build up high aspect ratio structures on undersized parts or to form devices by electroforming. Compared with other common MEMS (microelectromechanical systems) metal device fabrication techniques, such as vapor depositions, electroplating has several outstanding advantages. First, the fabrication process is cost-efficient because electroplating process can be set up easily …

Microstructure And Chemistry Evaluation Of Direct Metal Laser Sintered 15-5 Ph Stainless Steel, Kevin Coffy

Electronic Theses and Dissertations

15-5PH stainless steel is an important alloy in the aerospace, chemical, and nuclear industries for its high strength and corrosion resistance at high temperature. Thus, this material is a good candidate for processing development in the direct metal laser sintering (DMLS) branch of additive manufacturing. The chemistry and microstructure of this alloy processed via DMLS was compared to its conventionally cast counterpart through various heat treatments as part of a characterization effort. The investigation utilized optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-Ray diffractometry (XRD), energy dispersive X-Ray spectroscopy (EDS) and glow discharge atomic emission spectrometry (GDS) …