Materials Science and Engineering Commons^™

Electronic Structure Characterization Of Hybrid Materials, Zhi Li

USF Tampa Graduate Theses and Dissertations

In this dissertation, the studies aim to characterize the electronic structure at the internal interface of hybrid materials. The characterization challenge is originating from the spectral superposition of hybrid constituents. A characterization protocol based on photoemission spectroscopy (PES) was developed and applied to investigate the orbital alignment at the internal interface of the oligothiophene-TiO2 and ArS-CdSe hybrid materials by characterizing the individual constituents and the assembly hybrids respectively. Electrospray deposition technique was used to deposit targeting materials which enabled preparation of thin films in vacuum minimizing ambient contaminations while transmission electron microscopy (TEM) was used to investigate the morphology and …

Development Of Nanostructured Graphene/Conducting Polymer Composite Materials For Supercapacitor Applications, Punya A. Basnayaka

USF Tampa Graduate Theses and Dissertations

The developments in mobile/portable electronics and alternative energy vehicles prompted engineers and researchers to develop electrochemical energy storage devices called supercapacitors, as the third generation type capacitors. Most of the research and development on supercapacitors focus on electrode materials, electrolytes and hybridization. Some attempts have been directed towards increasing the energy density by employing electroactive materials, such as metal oxides and conducting polymers (CPs). However, the high cost and toxicity of applicable metal oxides and poor long term stability of CPs paved the way to alternative electrode materials. The electroactive materials with carbon particles in composites have been used substantially …

Novel Approach Of Using Polyvinylidene Fluoride Langmuir-Schaefer Film On Graphene-Polyaniline Nanocomposite For Supercapacitor Applications, Venkata Priyanka Bolisetty

USF Tampa Graduate Theses and Dissertations

Supercapacitors are well known for their improvised power density compared to batteries. Ongoing research is mainly focused on improving the energy density of supercapacitors by using different electrode material nanocomposites. The recent research has revealed that graphene (G)-polyaniline (PANI) nanocomposite could be a promising material for supercapacitor applications. The supercapacitor is also associated with self-leakage current regardless of any electrode material. The main objectives of the project are to: (i) synthesize highly fabricate supercapacitor based of G-PANI electrode; (ii) improve the energy density of supercapacitor by applying ultrathin monolayer/monolayers film electrode surface. It is crucial to either improve or retain …

Thermal Infrared Reflective Metal Oxide Sol-Gel Coatings For Carbon Fiber Reinforced Composite Structures, Brandon Demar Richard

USF Tampa Graduate Theses and Dissertations

Recent trends in composite research include the development of structural materials with multiple functionalities. In new studies, novel materials are being designed, developed, modified, and implemented into composite designs. Typically, an increase in functionality requires additional material phases within one system. The presence of excessive phases can result in deterioration of individual or overall properties. True multi-functional materials must maintain all properties at or above the minimum operating limit. In this project, samples of antimony and cobalt-doped tin oxide (ATO(Co2O3)) sol-gel solutions are used to coat carbon fibers and are heat treated at a temperature range of 200 - 500 …

Fabricating And Characterizing Physical Properties Of Electrospun Polypeptide-Based Nanofibers, Dhan Bahadur Khadka

USF Tampa Graduate Theses and Dissertations

This dissertation has aimed to fabricate polypeptide based biomaterial and characterize physical properties. Electrospinning is used as a tool for the sample fabrication. Project focused on determining the feasibility of electrospinning of certain synthetic polypeptides and certain elastin-like peptides from aqueous feedstocks and to characterize physical properties of polymer aqueous solution, cast film and spun fibers and fiber mats. The research involves peptide design, polymer electrospinning, fibers crosslinking, determining the extent of crosslinking, fibers protease degradation study, fibers stability and self-organization analysis, structure and composition determination by various spectroscopy and microscopy techniques and characterization of mechanical properties of individual suspended …

Evaluating Cfrp-Masonry Bond Using Thermal Imaging, Joseph Christopher Ross

USF Tampa Graduate Theses and Dissertations

This study presents results from non-destructive testing to evaluate the degradation of the CFRP-masonry bond using thermal imaging. The goal of the research was to identify locations where there was evidence of bond deterioration that could subsequently be verified through destructive pull-off testing.

Four full-scale masonry walls were built outdoors at the University of South Florida in 1995 to evaluate the effectiveness of CFRP for repairing settlement damage. Two of the settlement-damaged walls were repaired using single layer, commercially available unidirectional CFRP systems that used Tonen (wall 3) and Henkel (wall 2) epoxies. These two walls were the subject of …

Kelvin Probe Electrode For Contactless Potential Measurement On Concrete-Properties And Applications, Michael Thomas Walsh

USF Tampa Graduate Theses and Dissertations

The practical feasibility of using a Kelvin Probe as a novel reference electrode in the measurement of both potential and polarization pulse response of reinforcing steel in concrete is demonstrated. Potential values measured using a KP reflect greater stability and repeatability than can typically be attained with conventional reference electrodes. Duplicate reinforced concrete beam test specimens with well-differentiated centrally corroding rebar segments were analyzed using both the Kelvin Probe (KP) and a conventional Saturated Calomel Electrode (SCE). Potential profile maps were developed using potential values recorded under static conditions with both the SCE and the KP. Nominal polarization resistance was …

Synthesis And Investigations Of Type I And Ii Clathrates Of Group 14, Michael Blosser

USF Tampa Graduate Theses and Dissertations

Clathrates are a class of new materials that have an open-framework structure that allows guest atoms or molecules to be enclosed inside of their polyhedral framework. Varying the number, weight, and size of the guest species in a particular framework allows one to alter the physical properties of the clathrate. This relationship enables one to further the fundamental understanding of the physics and chemistry of the clathrate structure and use this knowledge to "tune" certain properties. This "tunability" of inorganic clathrates is of great interest as it allows one to optimize their physical properties; making them promising candidates for a …

Effect Of Cement Chemistry And Properties On Activation Energy, Andre J. Bien-Aime

USF Tampa Graduate Theses and Dissertations

The objective of this work is to examine the effect of cement chemistry and physical properties on activation energy. Research efforts indicated that time dependent concrete properties such as strength, heat evolution, and thermal cracking are predictable through the concept of activation energy. Equivalent age concept, which uses the activation energy is key to such predictions. Furthermore, research has shown that Portland cement concrete properties are affected by particles size distribution, Blaine fineness, mineralogy and chemical composition. In this study, four Portland cements were used to evaluate different methods of activation energy determination based on strength and heat of hydration …

Analytical And Numerical Modeling Of Assembly Procedures Of Steel Fulcra Of Bascule Bridges, Sriharsha Garapati

USF Tampa Graduate Theses and Dissertations

To model shrink-fitting in metal components, an analytical model for two long compound cylinders with temperature dependent material properties and interference between them is developed for calculating transient temperatures and stresses. A finite element model is developed for the same geometry which incorporated the temperature dependent material properties. A convergence study is performed on the finite element and analytical model. The finite element model is validated by comparing the approximations of finite element model with the analytical solution.

In an assembly procedure of fulcrums for bascule bridges, called AP1, the trunnion is shrink-fitted into a hub, followed by shrink fitting …

Structured Materials For Catalytic And Sensing Applications, Selma Hokenek

USF Tampa Graduate Theses and Dissertations

The optical and chemical properties of the materials used in catalytic and sensing applications directly determine the characteristics of the resultant catalyst or sensor. It is well known that a catalyst needs to have high activity, selectivity, and stability to be viable in an industrial setting. The hydrogenation activity of palladium catalysts is known to be excellent, but the industrial applications are limited by the cost of obtaining catalyst in amounts large enough to make their use economical. As a result, alloying palladium with a cheaper, more widely available metal while maintaining the high catalytic activity seen in monometallic catalysts …

Non-Equilibrium Melting And Sublimation Of Graphene Simulated With Two Interatomic Potentials, Brad Steele

USF Tampa Graduate Theses and Dissertations

The mechanisms of the sublimation of graphene at zero pressure and the condensation of carbon vapor is investigated by molecular dynamics (MD) simulations. The interatomic interactions are described by the Reactive Empirical Bond Order potential (REBO). It is found that graphene sublimates at a temperature of 5,200 K. At the onset of sublimation, defects that contain several pentagons and heptagons are formed, that are shown to evolve from double vacancies and stone wales defects. These defects consisting of pentagons and heptagons act as nucleation sites for the gaseous phase. The influence of the interatomic interactions on the sublimation process are …

Corrosion Of Post-Tensioning Strands In Ungrouted Ducts - Unstressed Condition, Michael John Hutchison

USF Tampa Graduate Theses and Dissertations

Recent failures and severe corrosion distress of post-tensioned (PT) bridges in Florida have revealed corrosion of the 7-wire strands in tendons. Post-tensioned duct assemblies are fitted with multiple 7-wire steel strands and ducts are subsequently filled with grout. During construction, the length of time from the moment in which the strands have been inserted into the ducts, until the ducts are grouted, is referred to as the `ungrouted' period. During this phase, the steel strands are vulnerable to corrosion and consequently the length of this period is restricted (typically to 7 days) by construction guidelines. This investigation focuses on determining …

Hierarchy Of Supramolecular Synthons In The Of Design Multi-Component Crystals, Padmini Kavuru

USF Tampa Graduate Theses and Dissertations

Most of the biological systems in nature are sustained by molecular self-assemblies which are the finest examples of supramolecular architectures. Non-covalent interactions are key concepts which govern these molecular assemblies. Inspired by these examples crystal engineering emerged as an important tool in supramolecular chemistry which aids in the invention of new molecular structures with desired properties. Understanding of how the molecules interact at the molecular levels enables one to rationally design novel solid forms with modulated physicochemical properties. This feature of crystal engineering has heightened its position in materials chemistry and is currently one of the most well studied fields …

Implementation And Optimization Of An Inverse Photoemission Spectroscopy Setup, Ervin Gina

USF Tampa Graduate Theses and Dissertations

Inverse photoemission spectroscopy (IPES) is utilized for determining the unoccupied electron states of materials. It is a complementary technique to the widely used photoemission spectroscopy (PES) as it analyzes what PES cannot, the states above the Fermi energy. This method is essential to investigating the structure of a solid and its states. IPES has a broad range of uses and is only recently being utilized.

This thesis describes the setup, calibration and operation of an IPES experiment. The IPES setup consists of an electron gun which emits electrons towards a sample, where photons are released, which are measured in isochromat …

Functional Magnetic Nanoparticles, James Gass

USF Tampa Graduate Theses and Dissertations

Nanoparticle system research and characterization is the focal point of this research and dissertation. In the research presented here, magnetite, cobalt, and ferrite nanoparticle systems have been explored in regard to their magnetocaloric effect (MCE) properties, as well as for use in polymer composites. Both areas of study have potential applications across a wide variety of interdisciplinary fields.

Magnetite nanoparticles have been successfully dispersed in a polymer. The surface chemistry of the magnetic nanoparticle proves critical to obtaining a homogenous and well separated high density dispersion in PMMA. Theoretical studies found in the literature have indicated that surface interface energy …

Metal Oxide Graphene Nanocomposites For Organic And Heavy Metal Remediation, Tanvir E. Alam

USF Tampa Graduate Theses and Dissertations

This thesis consists of two research problems in the water decontamination area. In the first work, the main focus is to understand the structure and photocatalytic activity of titanium dioxide with graphene (G-TiO2) which is synthesized by using sol-gel method. The photocatalytic activity of TiO2 is limited by the short electron hole pair recombination time. Graphene, with high specific surface area and unique electronic properties, can be used as a good support for TiO2 to enhance the photocatalytic activity. The obtained G-TiO2 photocatalysts has been characterized by X-Ray Diffraction (XRD), Raman Spectroscopy, Transmission Electron Microscopy (TEM), FTIR Spectroscopy and Ultraviolet …

Nonlinear Properties Of Nanoscale Barium Strontium Titanate Microwave Varactors, Tony S. Price

USF Tampa Graduate Theses and Dissertations

Barium strontium titanate thin film varactors have been widely investigated for the purpose of creating tunable front-ends for RF and microwave systems. There is an abundance of literature observing the capacitance-voltage behavior and methods on improving tunability. However, there is a lack of thorough investigations on the nonlinear behavior, specifically the third order intermodulation distortion, and the parameters that impact it. There is also a research void that needs to be filled for nanoscale barium strontium titanate varactors as nanotechnology becomes increasingly prevalent in the design of RF and microwave components.

This work aims to advance the understanding of nonlinear …

The Electronic Structure Of Biomolecular Self-Assembled Monolayers, Matthaeus Anton Wolak

USF Tampa Graduate Theses and Dissertations

The studies presented here address the characterization of the electronic structure of various self-assembled monolayers (SAMs) of peptide nucleic acid (PNA) and tetraphenylporphyrin (TPP) SAMs and arrays, formed on gold substrates.

PNA is a promising alternative to DNA for bio-sensing applications, as well as for strategies for self-assembly based on nucleic acid hybridization. In recent years charge transfer through PNA molecules was a focus of research due to possible applications in self-assembled molecular circuits and molecular tools. In light of this research it is interesting to investigate the electronic structure of PNA interfaces to gold, a potential electrode material.

TPP …

Encapsulation Of High Temperature Phase Change Materials For Thermal Energy Storage, Rupa Nath

USF Tampa Graduate Theses and Dissertations

Thermal energy storage is a major contributor to bridge the gap between energy demand (consumption) and energy production (supply) by concentrating solar power. The utilization of high latent heat storage capability of phase change materials is one of the keys to an efficient way to store thermal energy. However, some of the limitations of the existing technology are the high volumetric expansion and low thermal conductivity of phase change materials (PCMs), low energy density, low operation temperatures and high cost. The present work deals with encapsulated PCM system, which operates at temperatures above 500°C and takes advantage of the heat …

Synthesis And Physical Properties Of Group 14 Intermetallic Clathrates, Stevce Stefanoski

USF Tampa Graduate Theses and Dissertations

The search of materials relevant for thermoelectric and magnetocaloric applications, as well as materials that interact with light, is an important aspect of the materials science. Such materials can be used for solid-state power generation and refrigeration, as light sources, detectors, or controllers. Intermetallic clathrates have long been of interest for the materials science research. The promise these materials hold for useful applications ranges from thermoelectrics to photovoltaics and optoelectronics to potentially ultra-hard materials and magnetic cooling applications. Their unique physical properties are intimately related to their intriguing structural properties. Thus a fundamental understanding of the chemistry and physics of …

Corrosion Evaluation And Durability Estimation Of Aluminized Steel Drainage Pipes, Mersedeh Akhoondan

USF Tampa Graduate Theses and Dissertations

Aluminized steel pipes are expected to have a long service life, e.g. 75 years. Spiral ribbed aluminized pipes (SRAP) have been widely specified and used by the Florida Department of Transportation (FDOT) for drainage of runoff water. Confidence in the long term durability of SRAP has been challenged by recent unexpected early corrosion failures in various Florida locations. SRAP premature corrosion incidents have occurred in two modalities. Mode A has taken place in near-neutral soil environments and has often been associated with either gross manufacturing defects (i.e. helical cuts) or corrosion concentration at or near the ribs. Mode B took …

Theory And Modeling Of Graphene And Single Molecule Devices, Lyudmyla Adamska

USF Tampa Graduate Theses and Dissertations

This dissertation research is focused on first principles studies of graphene and single organic molecules for nanoelectronics applications. These nanosized objects attracted considerable interest from the scientific community due to their promise to serve as building blocks of nanoelectronic devices with low power consumption, high stability, rich functionality, scalability, and unique potentials for device integration. Both graphene electronics and molecular electronics pursue the same goal by using two different approaches: top-down approach for graphene devices scaling to smaller and smaller dimensions, and bottom-up approach for single molecule devices. One of the goals of this PhD research is to apply first-principles …

Chemical Mechanical Planarization Of Electronic Materials, Fnu Atiquzzaman

USF Tampa Graduate Theses and Dissertations

In the modern semiconductor manufacturing processes, chemical mechanical planarization (CMP) has attained important processing step because of its ability to provide global planarization. CMP is the planarization technique which is used for the removal of excess material, as left over from the previous processing steps. In addition, CMP offers a uniform surface that is essential for subsequent processing steps, especially for the high resolution photolithography processes. In simpler notation, CMP is a process where a chemical reaction enhances in obtaining a planar surface through removal of the mechanical materials from a wafer.

In this study, CMP performance of three electronic …

Crack Analysis In Silicon Solar Cells, Maria Ines Echeverria Molina

USF Tampa Graduate Theses and Dissertations

Solar cell business has been very critical and challenging since more efficient and low costs materials are required to decrease the costs and to increase the production yield for the amount of electrical energy converted from the Sun's energy. The silicon-based solar cell has proven to be the most efficient and cost-effective photovoltaic industrial device. However, the production cost of the solar cell increases due to the presence of cracks (internal as well as external) in the silicon wafer. The cracks of the wafer are monitored while fabricating the solar cell but the present monitoring techniques are not sufficient when …

Shape-Shifting Surfaces For Rapid Release And Direct Stamping Of Organized Micro-Tissues, Samuel James Dupont

USF Tampa Graduate Theses and Dissertations

The primary aim of the research in this study is to develop a robust and simple platform for the in vitro organization of cells on surfaces which facilitate rapid cell release and allows for the direct stamping of highly organized micro-tissues. Current approaches towards this goal have been very successful but are lengthy and subject cells to harsh conditions for extended periods of time raising questions regarding cell health and maintenance of physiological state. To address these concerns a platform was developed to allow for rapid cell release by utilizing a release mechanism different from previous work.

Micron-scale structures comprised …

Zno Nanostructures: Growth, Characterization And Applications, Mikhail Ladanov

USF Tampa Graduate Theses and Dissertations

ZnO nanostructures have been investigated for quite a long time. However, only recently they triggered much interest due to advances in materials synthesis and characterization, as well as emerging demand for new nanostructured materials in novel device implementations.

A large part of the work was devoted to exploring new methodology for patterning growth sites and controlling nanowires morphology using the deposition methods that are compatible with integrated circuits (IC) processing. Microcontact printing was used to pattern the seeding layer, and, subsequently, ZnO nanowires through a resistless soft lithography process.

When considering hydrothermal growth of ZnO nanowires in the framework of …

Development Of Interatomic Potentials For Large Scale Molecular Dynamics Simulations Of Carbon Materials Under Extreme Conditions, Romain Perriot

USF Tampa Graduate Theses and Dissertations

The goal of this PhD research project is to devise a robust interatomic potential for large scale molecular dynamics simulations of carbon materials under extreme conditions. This screened-environment dependent reactive empirical bond order potential (SED-REBO) is specifically designed to describe carbon materials under extreme compressive or tensile stresses. Based on the original REBO potential by Brenner and co workers, SED-REBO includes reparametrized pairwise interaction terms and a new screening term, which serves the role of a variable cutoff. The SED-REBO potential overcomes the deficiencies found with the most commonly used interatomic potentials for carbon: the appearance of artificial forces due …

Development Of A Reliable Metal-Insulator-Metal Bilayer Tunnel Junction For Wideband Detectors, Rudraskandan Ratnadurai

USF Tampa Graduate Theses and Dissertations

Detectors and sensors are an integral part of modern electronics and are crucial to highly sensitive applications. Metal-Insulator-Metal (MIM) tunnel junctions have been explored for the past five decades and are still being investigated due to its wide use of applications such as mixers, capacitors, detectors, rectifiers and energy conversion devices. In this research, various designs of thin film based tunnel junctions have been investigated and the optimum one picked for the purpose of a wide band detector up to 10GHz based on their sensitivities. A modified design with an isolation layer incorporating a self-aligning method to increase fabrication throughput …

Growth And Characterization Of Functional Nanoparticulate Films By A Microwave Plasma-Assisted Spray Deposition Process, Ted Wangensteen

USF Tampa Graduate Theses and Dissertations

Nanoparticle and nanoparticulate films have been grown by a unique approach combining a microwave and nebulized droplets where the concentration and thus the resulting particle size can be controlled. The goal of such a scalable approach was to achieve it with the least number of steps, and without using expensive high purity chemicals or the precautions necessary to work with such chemicals. This approach was developed as a result of first using a laser unsuccessfully to achieve the desired films and particles. Some problems with the laser approach for growing desired films were solved by substituting the higher energy microwave …