Materials Science and Engineering Commons^™

Dielectric Properties Of Polycrystalline And Single Crystal (100) Strontium Titanate From 4 To 295 K, Hung Trinh, Alan Devoe, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

The dielectric properties of single crystal and polycrystalline SrTiO₃ (ST) were investigated from 295 to 4 K. Relative permittivity (εr) and loss tangent (tan(δ)) were measured systematically as a function of direct current (DC) voltage (0 V/cm to 800 V/cm), frequency (100 Hz to 1 MHz), and temperature (295 K to 4 K) for type (100) single crystal SrTiO₃ (SC-ST) and for polycrystalline SrTiO₃ (PC-ST). Calculated equivalent series resistance (ESR) data are also reported. Overall, the permittivity of ST showed a dependence on temperature, DC voltage, and frequency. Dependences on voltage and frequency were only observed at …

Hanford Low-Activity Waste Vitrification: A Review, José Marcial, Brian J. Riley, Albert A. Kruger, Charmayne E. Lonergan, John D. Vienna

Materials Science and Engineering Faculty Research & Creative Works

This Paper Summarizes the Vast Body of Literature (Over 200 Documents) Related to Vitrification of the Low-Activity Waste (LAW) Fraction of the Hanford Tank Wastes. Details Are Provided on the Origins of the Hanford Tank Wastes that Resulted from Nuclear Operations Conducted between 1944 and 1989 to Support Nuclear Weapons Production. Waste Treatment Processes Are Described, Including the Baseline Process to Separate the Tank Waste into LAW and High-Level Waste Fractions, and the LAW Vitrification Facility Being Started at Hanford. Significant Focus is Placed on the Glass Composition Development and the Property-Composition Relationships for Hanford LAW Glasses. Glass Disposal Plans …

High-Temperature Oxidation Behavior Of High Entropy Carbide (Tanbtiv)C In Atmospheres With Different Oxygen Contents, Ruoyu Chen, Hongbin An, Jie Zhan, Saisai Li, Aiqin Mao, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

A high entropy carbide (TaNbTiV)C was fabricated via spark plasma sintering of high entropy powders that were prepared using a molten salt method. The as-fabricated high entropy carbide was then investigated for its high-temperature oxidation behavior at 850 °C, under atmospheres with three different oxygen contents (20 vol%, 40 vol%, and 60 vol%). After the high-temperature oxidation process, the main phases observed in all the specimens were incompletely oxidized phase (Nb_xTi_1-x)C_yO_2-y and oxides (Nb_0.5Ta_0.5)₂O₅, TiO₂, and Nb₂O₅. Importantly, the …

Synergistic Hardening In A Dual Phase High-Entropy (Hf,Nb,Ta,Ti,Zr)C–(Hf,Nb,Ta,Ti,Zr)B2 Ultra-High Temperature Ceramic, Rubia Hassan, William G. Fahrenholtz, Gregory E. Hilmas, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

A dual phase high-entropy (Hf,Nb,Ta,Ti,Zr)C–(Hf,Nb,Ta,Ti,Zr)B2 ultra-high temperature ceramic was synthesized using a single step boro-carbothermal reduction route. The synthesized powder was densified by spark plasma sintering at 2000°C, resulting in complete solid solution formation and a relative density of ≈99%. The dual phase ceramic was 43 vol% high-entropy carbide and 57 vol% high-entropy boride. The grain sizes were 0.85 ± 0.34 µm for the carbide and 0.87 ± 0.33 µm for the boride with minimal residual oxide (0.2 vol%) detected in the microstructure. The resulting composition had a higher microhardness than the individual boride and carbide ceramics across the range …

Cf/Sic Ceramic Matrix Composites With Extraordinary Thermomechanical Properties Up To 2000 °C, Min Sung Park, Jian Gu, Heesoo Lee, Sea Hoon Lee, Lun Feng, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The thermomechanical properties of carbon fiber reinforced silicon carbide ceramic matrix composites (Cf/SiC CMCs) were studied up to 2000 °C using high temperature in situ flexural testing in argon. The CMC specimens were fabricated using an ultrahigh concentration (66 vol%) aqueous slurry containing nano-sized silicon carbide powder. The SiC powder compacts were obtained by drying the slurry and were densified using the precursor impregnation and pyrolysis (PIP) method with field assisted sintering technology/spark plasma sintering (FAST/SPS). The high relative density of the SiC green body (77.6%) enabled densification within 2.5 days using four PIP cycles. In contrast, conventional PIP processes …

Phosphate-Based Dechlorination Of Electrorefiner Salt Waste Using A Phosphoric Acid Precursor, Paige Murray, Harmony Werth, Sean Sullivan, Brian J. Riley, Michael Simpson, Charmayne E. Lonergan, Krista Carlson

Materials Science and Engineering Faculty Research & Creative Works

Electrochemical processing of spent nuclear fuel in molten chloride salts results in radioactive salt waste. Chlorine removal from the salt has been identified as an effective and efficient first step in the management of high-level waste. In this work, a simple salt was dechlorinated with a phosphoric acid phosphate precursor, resulting in a glassy dechlorinated product. The dechlorination efficacy was evaluated in air and argon environments. This work serves as an initial step to advance the technological readiness level of h3po4-based dechlorination step toward implementation of iron phosphate waste forms to immobilize electrochemical fuel reprocessing salt waste streams.

Thermal And Electrical Properties Of Single-Phase High Entropy Carbide Ceramics, Paul M. Brune, Gregory E. Hilmas, William G. Fahrenholtz, Jeremy Lee Watts, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Thermal and Electrical Properties Were Investigated for Five Nominally Phase-Pure High Entropy Carbide Ceramics. the Compositions (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)C, (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C, (Hf0.2Mo0.2Ta0.2Ti0.2Zr0.2)C, (Hf0.2Ta0.2Ti0.2W0.2Zr0.2)C, and (Hf0.2Mo0.2Ti0.2W0.2Zr0.2)C Were Synthesized by Carbothermal Reduction of Oxides. the Thermal Diffusivity and Heat Capacity Were Measured from Room Temperature to 1800°C. the Room Temperature Thermal Conductivity Ranged from 5.1 W/mK for (Hf0.2Mo0.2Ti0.2W0.2Zr0.2)C to 9.0 W/mK for (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C. the Thermal Conductivity Increased over the Temperature Range with Maximum Conductivities of 19.6 W/mK Measured for (Hf0.2Mo0.2Ta0.2Ti0.2Zr0.2)C to 29.7 W/mK for (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C at 1800°C. the Electron Contribution to Thermal Conductivity Calculated from Measured Electrical Resistivity Varied from 41% to 52% of the …

Pressureless Sintering And Properties Of Additively Manufactured Zrb2–Sic, Marharyta Lakusta, Nicholas M. Timme, Jeremy L. Watts, William G. Fahrenholtz, Gregory E. Hilmas, David W. Lipke

Materials Science and Engineering Faculty Research & Creative Works

Densification behavior, grain growth kinetics, mechanical and thermal properties of pressurelessly sintered zirconium diboride–silicon carbide (ZrB2–SiC) fabricated by extrusion of high solids loading pastes have been studied. The effects of sintering temperature (1600–2300°C), heating rate during constant heating rate sintering (10–50°C/min), and time during isothermal sintering (3–24 h) on density and grain size were examined. The apparent activation energy for densification was determined to be 940 ± 90 kJ/mol, suggesting lattice diffusion as the dominant sintering mechanism. Grain growth of both ZrB2 and SiC followed a normal grain growth power law with grain growth exponent n = 2 indicating diffusion-controlled …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Spark Plasma Sintering Of Magnesium Titanate Ceramics, Suzana Filipović, Nina Obradović, William G. Fahrenholtz, Steven Smith, Miljana Mirković, Adriana Peleš Tadić, Jovana Petrović, Antonije Đorđević

Materials Science and Engineering Faculty Research & Creative Works

Magnesium titanate ceramics were prepared by reactive spark plasma sintering (SPS) at 1200 °C for 5 min. Prior to sintering, MgO and TiO₂ powders were mixed by high energy ball milling (HEBM) for 15, 30, or 60 min. The effect of milling time on phase composition was analyzed by X-ray diffraction (XRD) for milled powders and sintered specimens. The morphology of the sintered ceramics was investigated by scanning electron microscopy (SEM), while elemental distribution was determined by energy dispersive spectroscopy (EDS). The presence of the MgTi2O5 phase was detected in XRD and was confirmed by EDS analysis. Microcracking was …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. A prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. An alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Novel Re-Crosslinkable Preformed Particle Gels (Rppg) For Parent- And Infill-Well-Fracture Interactions Mitigation, Xiaojing Ge, Adel Alotibi, Ahmed Al-Hlaichi, Yanbo Liu, Tao Song, Junchen Liu, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Hydraulic fracturing treatments in unconventional infill (or "child") wells can be significantly affected by depletion from existing parent-well, resulting in asymmetrical fracture growth. These issues may lead to excessive load-water production, proppant deposition, casing deformation in the parent well, and unbalanced stimulation of infill wells. To mitigate these effects, various strategies have been proposed, including the use of far-field diverters in child wells and repressurization of parent wells. Additionally, an increasingly popular strategy involves injecting near-wellbore diverters to temporarily plug entry points into the parent wellbores during frac operations on infill wells. To achieve better application, a novel low-cost, self-degradable, …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. a prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. an alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Bioprinting With Adipose Stem Cells And Hydrogel Modified With Bioactive Glass, Krishna C.R. Kolan, Apurv Saxena, Bradley A. Bromet, Lesa B. Steen, August T. Bindbeutel, Julie A. Semon, Delbert E. Day, Ming C. Leu

Biological Sciences Faculty Research & Creative Works

Bioprinting research is focused on utilizing growth factors and multiple cell types to create clinically relevant three-dimensional (3D) tissue models using hydrogels. Rheological and biological challenges are two main factors that limit the creation of extrudable bioactive hydrogels. In this study, we investigate incorporation of fast dissolving and bioactive borate glass in different weight to volume percentages (0.075 to 0.6%) to alginate-gelatin (1:1) hydrogel to improve rheological properties and enable bioprinting with bioactive glass. The addition of glass improved the stiffness of the hydrogel. Human adipose-derived mesenchymal stem cells (ASCs) were uniformly mixed in this bioink at 1 x 106 …

Transitioning To A Lower Global Warming Refrigerant, A Performance Study Of R-513a And Hfc-134a In Commercial Chillers, Hossein Abedsoltan, Mark B. Shiflett

Chemical and Biochemical Engineering Faculty Research & Creative Works

The performance of R-513A and HFC-134a refrigerants is compared in two identical chillers operating at the University of Kansas. R-513A is a more environmentally friendly refrigerant due to its lower global warming potential that can be used as a retrofit replacement for HFC-134a in chillers. This study investigates the performance comparison of transitioning from HFC-134a to R-513A. The chillers have been in operation for two years, and cooling capacity, coefficient of performance, and other operating parameters are compared under similar cooling conditions. Cooling capacities ranged from 100 to 500 kW for both chillers. Overall, the energy consumption and coefficient of …

Production Of Glass-To-Metal Seals Using Additive Manufacturing Techniques, Aaron Read

Masters Theses

"Glass-to-metal (GtM) seals are hermetic barriers between glass and metal components, often used in the electronic and vacuum industries. Creating the seals traditionally requires heating all the components to the glass melting temperature, where the glass will flow and bond to the metal. Due to the manufacturing constraints of the individual components and sealing conditions there are geometric and material restrictions. Additive manufacturing techniques were used to make GtM seals to reduce these restrictions.

Hermetic, single pin seals were produced using printed metal shells, by selective laser melting (SLM), and digital light processing (DLP) printed glass preforms. Glass preforms were …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Enhanced Bottom Anode Monitoring In Dc Electric Arc Furnaces Using Fiber Optic Sensors, Yeshwanth Reddy Mekala, Rony Kumer Saha, Ogbole Collins Inalegwu, Muhammad Roman, Farhan Mumtaz, Rex Gerald, Jeffrey D. Smith, Jie Huang, Ronald J. O'Malley

PSMRC Faculty Research

A pin style bottom anode employs conductive steel rods that serve as the pathway for the high electrical power through rammed refractory at the bottom of a DC Electric Arc Furnace (EAF). Anode wear during operation is important to monitor, as anode replacement is expensive and impacts EAF productivity. Liquid steel penetration into the un-sintered refractory layer can result from rapid electrical power ramp-up, dips in furnace temperature, or operating the anode for too long between EAF campaigns. In extreme cases, the liquid steel may penetrate the bottom of the furnace when anode wear progresses too close to the bottom …

Sic Addition To A Dual Phase High Entropy Ultra-High Temperature Ceramic, Rubia Hassan, William G. Fahrenholtz, Kantesh Balani, Gregory E. Hilmas, Jeremy Watts

Materials Science and Engineering Faculty Research & Creative Works

Dual phase (Hf,Ta,Ti,W,Zr)B2-(Hf,Ta,Ti,W,Zr)C high entropy ultra-high temperature ceramics were processed from commercial diboride and carbide powders with and without SiC additions. A 30-min hold at a maximum temperature of 1850 °C in spark plasma sintering resulted in a relative density of ∼95 %, which increased to ∼100 % with the addition of 7.5 wt.% SiC. The compositions did not reach chemical equilibrium under the given sintering conditions resulting in an inhomogeneous distribution of transition metals in both the boride and carbide phases. The addition of SiC improved densification by inhibiting grain growth, which reduced the grain size from 9.0 ± …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. to this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. a dual-belt separator was designed to reduce middlings. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

Beneficiation Of Lunar Regolith Simulants Through Electrostatic Sieving And Magnetic Separation, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

In the light of future development of lunar structures, in-situ feldspar beneficiation is imperative for metal extraction. This research incorporates the tandem use of electrostatic sieving and magnetic separation for collecting a specific size range and mineral composition from lunar soil that optimizes subsequent chemical processing. While earlier works focused on silt-sized particles, this work expands that range up to medium-grained sand with a greater variety of potential lunar regolith compositions. This work shows that a 2.5 kV, 7 Hz to 30Hz frequency, single-phase square wave can lift silt and fine sand for collection. This lifting is successful directly from …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. The new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. The simulation achieved similar yields reported in previous works, which served as validation of the model. The new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Development Of A Highly Loaded Zirconium Carbide Paste For Material Extrusion Additive Manufacturing, Clare Sabata, Austin J. Martin, Jeremy L. Watts, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

A highly loaded, aqueous-based zirconium carbide (ZrC) paste was developed for ceramic on-demand extrusion (CODE). Commercial ZrC powder was ball milled to reduce the particle size to ∼1 μm. Paste composition was determined by rheological characterization and observation of printing behavior; the final paste consisted of 46–47 vol% ZrC, 43.5 vol% distilled water, 8.1 vol% dispersant, and 1.6 vol% binder. Rheological characterization of the paste showed a yield stress of ∼8 Pa and shear thinning behavior (ΔG′/Δσ* = −55). The paste was printed using a 610 μm nozzle; a test print showed shape fidelity using the developed paste. A pressureless …

Effect Of Sc Spatial Distribution On The Electronic And Ferroelectric Properties Of Alscn, Bipin Bhattarai, Xiaoman Zhang, Wangwang Xu, Yijia Gu, W. J. Meng, Andrew C. Meng

Materials Science and Engineering Faculty Research & Creative Works

While aluminum scandium nitride based ferroelectric materials have shown significant promise for non-volatile memory applications, difficulties relating challenges in device performance, such as electrical leakage, to structural characteristics motivate improved understanding of the fundamental structure-property relationship. Spinodal decomposition has been reported in this material system, consistent with our observation of compositional segregation in AlScN films grown by reactive sputter epitaxy. To better understand the effects of spatially non-uniform Sc concentrations, the electronic and ferroelectric (FE) properties of AlScN as a function of Sc distribution are studied using density functional theory (DFT). We explore the impact of Sc-rich atomic planes in …

Phenolic Polymer Infiltration And Pyrolysis Process For Additively Manufactured Carbon/Peek Composites To Produce Carbon–Carbon Composites, S. Weiler, H. A. Haffner, K. Chandrashekhara, J. Watts, G. E. Hilmas, J. Bayldon, L. M. Rueschhoff

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Carbon–carbon composites are carbon fibers reinforced with carbon matrix and are classified as advanced materials well suited for high-temperature structural applications. Carbon–carbon composites are characterized by maintaining excellent mechanical properties and structural stability at high temperatures and have been used in aerospace application as nozzles, heatshields, and leading edge. However, conventional methods to manufacture carbon–carbon composites are costly and time-consuming. the aim of this work is to develop a method for creating additively manufactured (AM) carbon–carbon composites using a high-pressure re-infiltration process. in doing so, less infiltration cycles are required compared to a low-pressure re-infiltration, reducing the total manufacture time. …

Damage Initiation Of 15v38 Steel Bar During Square-To-Round Hot Rolling Process, Siva Sai Krishna Dasari, Henry Adekola Haffner, K. Chandrashekhara, Mario F. Buchley, Simon N. Lekakh, Ronald J. O'Malley

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Hot rolling processes have been extensively used to produce round bars by reducing the cross-sectional area of continuously cast steel. The current trend toward increasing productivity often requires a more aggressive reduction per pass. Establishing safe and optimized hot rolling parameters must be determined to avoid damage while deforming the specific steel composition. Understanding the damage mechanism during the metal forming process is vital for product quality. Herein, a combined experimental and simulation approach is developed to track the evolution potential damage during hot bar rolling. Hot tension tests are conducted on as-cast vanadium micro alloyed 15V38 steel at different …

Thermodynamic Analysis Of Metal Segregation In Dual Phase High Entropy Ceramics, Steven M. Smith, William G. Fahrenholtz, Gregory E. Hilmas, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Equilibrium Gibbs' free energy calculations were used to determine metal segregation trends between boride and carbide solid solutions containing two metals that are relevant to dual phase high entropy ceramics. The model predicted that Ti had the strongest tendency to segregate to the boride phase followed by Zr, Nb, Mo, V, Hf, and Ta, which matches experimental results of measured compositions. The ratio of a metal in the carbide phase to the content of the same metal in the corresponding metal boride had a linear trend with the change in standard Gibbs' free energy of reaction for a metal carbide …

A Super-Hard High Entropy Boride Containing Hf, Mo, Ti, V, And W, Suzana Filipovic, Nina Obradovic, Greg E. Hilmas, William G. Fahrenholtz, Donald W. Brenner, Jon Paul Maria, Douglas E. Wolfe, Eva Zurek, Xiomara Campilongo, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Super-Hard (Hf,Mo,Ti,V,W)B2 Was Synthesized by Boro-Carbothermal Reduction and Densified by Spark Plasma Sintering. This Composition Was Produced for the First Time as a Single-Phase Ceramic in the Present Research. the Optimized Ceramic Had a Single Hexagonal AlB2-Type Crystalline Phase with a Grain Size of 3.8 µm and Homogeneous Distribution of the Constituent Metals. the Vickers Hardness Exhibited the Indentation Size Effect, Increasing from 27 GPa at a Load of 9.8 N to as High as 66 GPa at a Load of 0.49 N. This is the Highest Hardness Reported to Date for High Entropy Boride Ceramics.

Oxidation Of Additively Manufactured Zrb2–Sic In Air And In Co2 At 700–1000 °C, Marharyta Lakusta, Nicholas M. Timme, Abid H. Rafi, Jeremy Lee Watts, M. (Ming) C. (Chuan) Leu, Gregory E. Hilmas, William G. Fahrenholtz, David W. Lipke

Materials Science and Engineering Faculty Research & Creative Works

Oxidation behavior of additively manufactured zrb2–sic in air and in co2 is reported in the temperature range of 700–1000 °c. Observed scale morphologies in air and in co2 were similar, featuring an outer borosilicate layer and an inner porous zirconia layer containing partially oxidized silicon carbide particles and remnant borosilicate products. Oxide scale thicknesses and parabolic scaling constants in air were approximately twice those observed in co2 across all studied temperatures. Activation energies for oxidation of 140 ± 20 kj/mol in air and 110 ± 20 kj/mol in co2 were determined, indicating similar diffusion processes that appear to be rate-limiting. …