Materials Science and Engineering Commons^™

Carbon Monoxide Attack Of Refractories, William A. Frad

Doctoral Dissertations

"The disintegration and failure of fire clay refractories due to the action of carbon monoxide has been studied tor a period at about fifty years. The most important application is in blast furnace refractories. Similar failures due to carbon deposition, involving other gases such as methane, have been noted and less extensively studied. Failures due to the action of gases other than carbon monoxide are beyond the scope of this thesis. Occasional attempts to find some agent to prevent disintegration have been mentioned in the literature. In this study the number of such substances and the results of their action …

A Fundamental Study Of Clay Drying Using Ware Of Large Cross Section, Robert F. Grady Iii

Masters Theses

"The drying of clay has been studied extensively in the past by many investigators, some of whom attempted to relate this information to the structure of clay and thereby develop a more vivid picture, while others studied the mechanism of drying in its own right in order to present a useable theory that would allow improvements in the drying operation.

At present the literature is unable to present a theory of the mechanism of drying that is sufficiently general to cover the observed aspects of clay drying. Many and varied mechanisms are presented, but correlation is seldom completely evident between …

Testing Of Missouri Shales For Light Weight Aggregate Production, Jerry D. Plunkett

Masters Theses

"The original objective of this investigation was to determine by testing those clays, shales, and loesses occuring in Missouri in large deposits (over 15 feet in thickness with little overburden), which would be suitable for the production of light weight aggregate. The second objective was to investigate the mechanism of bloating as related to the physical and chemical properties of the above materials, and by using these relationships cause clays which do not naturally bloat, to bloat using some addition. The use of additives would permit the economical use of material closer to the market in many instances.

After the …

Deposition Of Metallic Coatings From Fused Salt Baths, Andrew Hessler Larson

Masters Theses

"This thesis is the result of an investigation undertaken to study some of the important factors affecting the deposition of metallic diffusion coatings on other metals immersed in a fused salt bath….

There are many methods which have been devised to obtain diffusion coatings on various metals. One which is quite well known and used commercially is the process of “chromizing” which produces a diffusion layer if chromium on another metal. One method of “chromizing” consists of immersing the specimen to be coated in a mixed chloride fused bath containing chromium metal flakes. Another method consists of packing a low …

Effect Of Carbon Content In Steels Upon The Deposition Of Titanium From A Fused Salt Bath, Reinhard Paul Abendroth

Masters Theses

"STATEMENT OF PROBLEM Previous work done at the Missouri School of Mines and Metallurgy on the deposition of titanium upon various metals, especially iron and steel, bas shown that titanium can be deposited upon ingot iron and. low carbon steels with comparitive ease. Difficulty was encountered in attempts to deposit titanium upon steels of higher carbon content and upon cast irons.

For this reason, it was decided to investigate more thoroughly the relationship between the carbon content of various steels and the quality of titanium coatings deposited on these steels. Once this relationship had been established, a suitable theoretical explanation …

Corrosion Products Of Titanium In Fused Salt Baths, Kai-Chai Chiou

Masters Theses

"Titanium is gaining great interest in the modern metal industry because of its natural abundance and its desirable physical and chemical properties. Among them, its excellent corrosion resistance, such as the resistance to normal atmosphere attack, humid and saline atmosphere attack, sea water attack, and nitric acid attack, is the most prominent characteristic being welcomed by the engineers. The usefulness of titanium would be greatly increased if it were possible to plate titanium on other metals, thus increasing the corrosion resistance of these other metals.

Much concern, at present, has been given to the possibilities of the electrodeposition of titanium …

Mechanism And Measurement Of First Stage Graphitization In White Cast Iron, David S. Gould

Masters Theses

"The original object of this thesis was to ascertain if coercive force measurements could be used for the determination of degree of malleablization in malleable iron. Since first stage graphitization was involved, it was only natural that an interest in the mechanism of first stage graphitization developed. The investigation which resulted from this interest was done primarily for the edification of the author, however it was subsequently deemed of enough importance to be included in this thesis. For this reason the thesis may appear at times to deviate from the original objective"--Preface, page iii.

An Investigation Of The Characteristics Of High Alumina Refractory Castables, Gajendra Nath Mohanty

Doctoral Dissertations

"Refractory castables or concretes, a comparatively new member of the refractories family, are an admixture of highly aluminous cements and graded refractory aggregates, blended in predetermined proportions very much like structural concrete. The refractory aggregates must contain a large amount of fines contrary to the requirements of ordinary concrete. Unlike the Portland cements, which are mainly combinations of calcium silicates, the highly aluminous cements are predominantly calcium aluminates. They are comparatively of a refractory natures, having the hydraulic setting property combined also with high early strength. The discovery of the fact that these refractory concretes could be cast, in situ, …

The Rate Of Dissolution Of Aluminum In Hydrofluoric Acid, Yen-Ngen Wang

Doctoral Dissertations

"Pure aluminum has a relatively low strength, and its use is, therefore, rather limited. However, the resistance of pure aluminum to the attack of acids and many neutral solutions is higher than that of less pure aluminum or most of the aluminum-base alloys. For this reason, alclad alloy sheets, are made with a coating of pure aluminum on one or both sides of an aluminum alloy core. The coating is metallurgically bonded to the core over the entire area of contact. Thus the coating electrochemically protects the core from corrosive attack.

Aluminum is more negative in the electrochemical series than …

Hydrogen Overvoltage On Titanium, Sheng-Tai Shih

Doctoral Dissertations

"The hydrogen overvoltage has been defined as the difference between the potential of the working electrode (cathode) and the theoretical reversible value for the same solution. This definition brings out the difficulty involved in the measurement of the "theoretical reversible potential for the same solution” as the potential of the hydrogen electrode in such a solution is usually different from the value of a standard reversible hydrogen electrode, for which the activity of hydrogen ions is set as being “1” and the potential arbitrarily set as being “0”. Besides, it is sometimes necessary to add addition agents to the solution …

A Study Of The Deformation Texture And Its Variation In Cold Drawn Nickel Rods, Krishan Kumar Tangri

Doctoral Dissertations

"The production of rods by cold drawing is a development of recent years as compared to other methods of fabrication. Though a good many investigations correlating the observed mechanical properties to the mill practices employed have been reported, the results nevertheless are more of a qualitative and empirical nature. It is well known that the physical properties of a metal product are related to its deformation textures which are characteristic of the metal and the fabricating method used. Thus a study of the deformation textures of cold-drawn rods, specially by x-ray diffraction techniques should provide a much more precise and …

The Preparation Of Zirconium Powder, Herbert S. Kalish

Professional Degree Theses

"The preparation of zirconium powder by several different methods is fully described and evaluated. Most of the methods described are of a rather classical nature and these methods are discussed as taken from their original sources with suggestions for possible streamlining. Flow sheets are provided.

The first series of steps to produce zirconium powder is almost invariably the production of pure zirconium tetrachloride or pure zirconium oxide from the tetrachloride. The processes described include the sodium reduction of zirconium tetrachloride, sodium reduction of the double alkali fluorides, the calcium reduction of zirconium oxide, hydrogen embrittlement and comminution of reduction products. …

The Bloating Of Missouri's Shales, Peter Kurtz Jr.

Masters Theses

"The first objective of this investigation was to determine which deposits of clays, shales, and loesses in Missouri are suitable for use in the production of lightweight aggregate by virtue of their expanding characteristics upon heating. The second objective was to determine, if possible, commercially feasible additions that will produce the bloating property in shales that do not naturally bloat.

There are two conditions which must be met in firing in order to bloat a clay or shale. First, a gas must be formed and evolved during firing. Second, enough glass of the proper viscosity must be formed to trap …

The Lattice Constant And Coefficient Of Expansion Of Chromium, Chao-Ching Weng

Masters Theses

"The most important use of chromium, other than as an alloying element in the manufacture of stainless steel, is for electroplating; to form a coating on other metals for corrosion prevention in order to procure longer life, and to achieve a decorative effect.

The physical properties of chromium are important in the effectiveness of its uses, and its lattice constant, as well as coefficient of thermal expansion, seem worthy of exact determination.

A number of research workers, over a span of thirty years, have spent considerable effort in determining the aforementioned constants. However, their results do not check, and the …

Vapor Pressures & Relative Stabilities Of Certain Double Flourides, Walter L. Gage

Missouri School of Mines and Metallurgy Reports

The vapor pressures and relative stabilities of certain double fluorides such as sodium titanium fluoride and strontium titanium fluoride will be investigated by heating them under vacuum to determine the extent of evaporation or decomposition.

An Investigation Of The Deformation Textures Of Titanium, Dean Nesbit Williams

Doctoral Dissertations

"With the increase in production of titanium in recent years has come a great interest in the mechanical properties and in the possible uses of this metal. Due to the affinity of titanium for oxygen, nitrogen, carbon, and hydrogen, and the market effect of these elements on the mechanical properties, much of the work previously reported is unreliable. As purer commercial grades of titanium and high purity iodide titanium have become available for examination, research has been undertaken to correct and expand the knowledge of the properties of titanium. Although the uses of titanium are limited at the present time, …

The Effect Of Impeller Speed And Air-Volume On The Flotation Rate With Respect To Particle Size, William Edward Horst

Masters Theses

"Today the ore being mined is low grade and the mineralization has become very complex. In order to concentrate a complex ore, the requirement of grinding the ore very fine is imposed. The process of flotation was developed to concentrate the finely ground ore particles; however, the finer size fractions of the ore still present a concentrating problem.

The fact has been established that the flotation rate which is the recovery that can be attained during a given time interval varies with particle size. The flotation rate increases with an increase in particle size until the maximum flotation rate is …

X-Ray Studies Of Zirconium Cyanonitride, John T. Ballass

Masters Theses

"The purpose of this research was to study, by means of x-ray and metallographic analysis, a material reported to be zirconium cyanonitride.

The x-ray analysis had a three fold purpose, the determination of the symmetry of the constituents, the number of phases present, and the crystal structure type. Metallography was used to confirm some of the results obtained by x-ray analysis establishing certain definite phase relationships present in the microstructure.

The sample investigated contained three principal elements namely zirconium, nitrogen, and carbon. On the basis of constitution this work is a contribution toward the development of the three component equilibrum …

Direct Reduction Of Zinc Sulfide Under Vacuum, Merritt E. Langston

Masters Theses

"The present work is a continuation of the previous investigations of Gross and Warrington and Liu in which the effect of various reducing agents on the vacuum reduction of zinc sulfide was studied. The author became interested in this topic while reading the papers by these investigators in which they recommended that further work be performed in an attempt to prevent zinc sulfide from distilling over during reduction, thereby contaminating the zinc condensate. The original plan was to perform a few runs for the purpose of duplicating the results that were reported by Liu, and from this point carry on …

Dissociation And Relative Stability Of Sodium Fluotitanate, Walter L. Gage

Masters Theses

"Titanium is urgently needed in the armament industry especially as a substitute for 18-8 stainless steel. There would be an almost inexhaustible supply of ores of titanium if high-purity titanium metal could be produced economically in large quantities. The use of titanium would permit much of the scarce nickel and chromium to be made available for other important uses.

It has been found by H. C. Kawecki and E. J. Bielecki that high-purity Na₂TiF₆, K₂TiF₆, and (NH4)₂TiF₆ can be produced from iron-bearing titaniferous raw material, ilmenite ores, or a …

Activation Energy For Recrystallization In Rolled Silver, Krishan Kumar Tangri

Masters Theses

"In several metals the process of recrystallization is accompanied by a change in the orientation of the recrystallized material with respect to the cold rolled material. If the change is sufficiently large, the changing position of the crystals can be determined by measuring the change in the intensity of the characteristic Bragg-reflection with a Geiger counter x-ray spectrometer. Recent determinations of the activation energies of copper and a 50/50 iron-nickel alloy have been made by using this x-ray technique. Both of these metals show a decided shift in the orientation as the material is recrystallized.

Silver was examined to find …

Autographic Determination Of Thermally-Induced Linear Changes In Ceramic Bodies, William Dean Mckee Jr.

Masters Theses

"The determination of changes in length of ceramic compositions as a function of temperature is frequently required in ceramic research and testing. With the use of an observer, excellent means are available for determination of changes in length over moderate ranges of temperature. However, the extended period required for some tests makes desirable the automatic recording of length change as a function of temperature.

There has been in use in the Ceramic Engineering Department a furnace arranged for determination of length changes; this furnace, shown in Figure 1, is so arranged that change in sample length causes linear displacement of …

A Study Of The Dissolution Of Titanium In Acids With Ammonium Fluoride Added, Charles Burroughs Gill

Doctoral Dissertations

"Titanium can no longer be considered a rare metal, even though the modern era of its production came into being only a few years ago. The first discovery of titanium was in 1791 by an English clergyman, the Reverend William Gregor, and the name titanium became universally adopted when so called by a German mineralogist, Martin Klaproth, who rediscovered titanium three years later. Not until 1887 was the relatively pure, 75 percent, metal prepared by L. F. Nilson and O. Pettersson, whose experiments were repeated in 1910 by M. A. Hunter. Hunter is given credit for producing the first metallic …

Determination Of Progressive Corrosion Of Clay Flux Blocks, Ved Prakash Maheshwary

Doctoral Dissertations

"The Problem. Corrosion of refractories by molten corrosive liquids like molten slags and glasses is of general occurrence in those parts of the furnaces where they come in contact with the liquids. The life of a furnace generally depends upon the progressive rate of corrosion of the refractories by the slags and glasses. There have been various methods used by the investigators to ascertain the useful life of a refractory product before its use in the furnaces, but the problem is so complex that even after decades of research work by the research engineers and technologists a satisfactory and easy …

Direct Reduction Of Zinc Sulfide Under Vacuum -- Course Work, Merritt E. Langston

Missouri School of Mines and Metallurgy Reports

A study of the reduction of zinc sulfide under vacuum by such reducing agents as iron, calcium oxide and carbon, graphite, and iron and carbon.

An attempt to refine the impure zinc metal condensates obtained from the above reductions under under by the mechanism of a differential displacement of the volatile constituents.

Progress Report: Reduction Of Zinc Sulfide, Merritt E. Langston

Missouri School of Mines and Metallurgy Reports

To date the work which has been completed has been concerned with an attempt to duplicate the results reported by Liu in his thesis. In short, little can be said in comparing the two separate investigations because there does not seem to be any apparent similarity, even though the operating conditions were kept as nearly the same as possible. Figure 1 shows the lack of agreement for the amount of total zinc distilled, expressed as weight percent....

An Investigation Of Ruthenium As A Possible Ceramic Colorant, John Charles Williams

Masters Theses

"Some portion of almost every writing dealing with the historical development of ceramic products is devoted to describing the application of colors as found on even the most ancient specimens known to exist. A vase bearing the name of an Egyptian king living 5000 B. C. was glazed in green and inlaid with purple. There are many such examples of the utilization of color in ceramics which illustrate to a certain extent the aesthetic tastes of the very earliest and primitive civilizations.

In those early times, only a few elements were known and available that could be used for such …

A Study Of Some Raw Materials For The Manufacture Of Silica Brick, Charles E. Shulze

Masters Theses

"The ability of silica to carry a load to within a few degrees of its melting point and its tolerance for comparatively high concentrations of iron oxide and lime, have enabled it to maintain its position as the number one steelplant refractory. It is estimated that at least half of the volume of refractories used in the steel plant are silica bricks. Consequently the manufacture of silica refractories forms an industry of considerable importance.

Raw materials suitable for the manufacture of silica brick are widely distributed, but only a small number of deposits are used commercially for one reason or …

The Effect Of Temper Carbon Nodule Number On The Physical Properties Of A Malleable Iron, William J. Ruprecht

Masters Theses

"It is known that the number of temper carbon nodules per unit volume of malleable iron has an effect on both the rate of anneal and on the resulting physical properties, but neither have been clearly worked out quantitatively. The purpose of this investigation is to ascertain the effect of temper carbon nodule number on certain of the physical properties of a commercial malleable iron.

Quantitative determinations of the effect of temper carbon nodule number would be essential from a theoretical viewpoint in working out the mechanism of graphtization, and would be useful in commercial practice in showing the most …

The Depression Of Quartz In Sulphide Flotation, William Mcminn Billinghurst

Masters Theses

"The flotation of sulphide minerals from siliceous and calcareous gangue minerals always gives a concentrate that is contaminated to a greater or lesser degree with the gangue minerals, even though the collectors used do not show any appreciable collecting properties for the gangue minerals when they are treated alone. In an effort to reduce the amount of undesirable gangue mineral floated with the concentrate it is the practice to add arbitrary amounts of various reagents such as quebracho, alkali hydroxides, carbonates, silicates, sulphides, phosphates, fluorides, and sulphuric acid which have been found to be advantageous. The mechanism of depression is …