Materials Science and Engineering Commons^™

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Zrc Particle Size Effect On The Mechanical Properties Of Spark Plasma Sintered 60–40 Vol% Zrc–Mo Cermets, Nathaniel Blatt, Jeremy Watts, Brian Taylor, Jhonathan Rosales, Gregory Hilmas

Materials Science and Engineering Faculty Research & Creative Works

Cermet's of 60 vol% ZrC and 40 vol% Mo with different starting ZrC particle sizes were spark plasma sintered to full density at 1950 °C. Elastic moduli, Vickers hardness and fracture toughness were measured at room temperature and flexural strength was measured up to 1600 °C. Young's modulus was 365 ± 5 GPa, shear modulus was 149 ± 2 GPa, Poisson's ratio was 0.22 ± 0.01, and no significant difference was observed for the moduli with respect to the starting ZrC particle size. Room temperature flexural strength was affected by the ZrC particle size, measured as ∼524 and ∼598 MPa …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

High-Temperature Performance Of Alloyed Cast Irons And Cr/Ni Austenitic Steels—An Overview And Discussion, Simon N. Lekakh, Mei Li, Larry Godlewski

Materials Science and Engineering Faculty Research & Creative Works

Fe-based cast alloys, including cast irons and steels, have been used in service at a wide range of mechanical and thermal load in oxidizing environment. Special alloying practices can be used to improve high temperature performance of Fe-based cast alloys in an oxidizing atmosphere. At elevated temperatures, alloying elements can produce a protective interface layer which prevents oxidant penetration into the metal matrix. However, a combination of thermo-mechanical loads along with surface oxidation can decrease the materials integrity by destroying the stable protected interface limiting the range of working parameters and lifetime performance of the material. This overview aims to …

Ultrafast Belite (Β-C2s) Production Using Biofuel-Based Combustion Synthesis, Shubham Agrawal, Sayee Srikarah Volaity, Oluwadamilare Charles Adesina, Bryan K. Aylas-Paredes, Taihao Han, Srinivas Kilambi, Aditya Kumar, Narayanan Neithalath

Materials Science and Engineering Faculty Research & Creative Works

This study presents a novel low-temperature, combustion synthesis (CS) approach for the rapid production of belite-rich cements. CS leverages the exothermic heat released from the combustion of biofuels such as lignin and/or biomass, intermixed with pelletized limestone and quartz. At an imposed furnace temperature of ∼700°C (as opposed to 1200°C–1300°C required in a conventional kiln), the source materials are rapidly transformed to belite, resulting in energy, emissions, and economic benefits. This work explores the influence of various process parameters, viz., fuel types and contents, airflow rate, porosity, holding temperature, and holding time on the efficiency of CS-based belite synthesis. Through …

Flexural Strength Of (Hf,Nb,Ta,Ti,Zr)B2–(Hf,Nb,Ta,Ti,Zr)C High-Entropy Dual-Phase Ceramics, Rubia Hassan, William G. Fahrenholtz, Gregory E. Hilmas, Jeremy Watts

Materials Science and Engineering Faculty Research & Creative Works

The room and elevated temperature flexural strengths were measured for (Hf,Nb,Ta,Ti,Zr)B2–(Hf,Nb,Ta,Ti,Zr)C high-entropy dual-phase ceramics. The fracture of ceramics originated from two distinct flaw populations that were either surface defects introduced during specimen preparation or volume defects introduced during processing. The average strength at room temperature was 638 ± 94 MPa with individual bars strengths as high as ∼800 MPa. At 1800°C, average strength increased to 786 ± 265 MPa with individual bar strengths as high as ∼1050 MPa. Above 1800°C, creep dominated resulting in deformation of the bars without fracture. The fracture mode changed from completely trans granular at room …

Roadmap To 100 Gwdc: Scientific And Supply Chain Challenges For Cdte Photovoltaics, B. Edward Sartor, Samantha B. Reese, Lorelle M. Mansfield, Ryan Muzzio, Chun Sheng Jiang, Eric Colegrove, John S. Mangum, Camden L. Kasik, Daniel Z. Shaw, James R. Sites, Ramesh G. Dhere, Alex B. Goldstone, Michael S. Moats

Materials Science and Engineering Faculty Research & Creative Works

This roadmap highlights pathways to expand the CdTe module manufacturing capacity per year to 100 GWDC by 2030 by improving Te extraction from existing supply chains, minimizing Te usage in modules by leveraging thinner absorbers, and focusing research efforts in key areas to improve module efficiencies. Both scientific and supply chain innovations will be necessary to maintain the high compound annual growth rate of the CdTe photovoltaic (PV) industry and cement its role as a key technology for multi-TW-scale PV deployment.

Oxidation Behavior Of Silicon Carbide, Matrix Graphite, And Refractory Multi-Principal Element Alloy, Visharad Jalan

Doctoral Dissertations

"The present study focuses on the investigation of the oxidation behavior of silicon carbide, matrix graphite in a water vapor environment. It also examines the oxidation behavior of refractory multi-principal element alloys when exposed to air. The oxidation behavior of silicon carbide and matrix graphite were investigated in conditions pertaining to off-normal incidents in high-temperature gas-cooled nuclear reactors. Understanding this is crucial for the prediction of their performance in such accidents and ensuring that the nuclear reactor is accident tolerant. Upon exposure to water vapor, the two A3-based matrix graphite exhibited different behaviors. The A3-27 type showed oxidation in all …

Machine Learning Modeling For Hydrolysis Recycling Of Pet Waste, Jie Li, Lanjia Pan, Hossein Abedsoltan, Hailong Wang, Taiyang Liu, Xiangzhou Yuan, Yong Sik Ok, Yin Wang

Chemical and Biochemical Engineering Faculty Research & Creative Works

The hydrolysis of polyethylene terephthalate (PET) into terephthalic acid (TPA) can efficiently recycle waste PET, but achieving high conversion efficiency through smart reaction design remains challenging. To develop a robust and accurate machine learning (ML) model for the in-depth understanding and intelligent design of PET hydrolysis, we compiled a new dataset comprising 942 data points and comprehensive information of 44 variables involved in heating type, acid/base catalyst (ABC), organic solvent (OS), co-solvent (CS), phase transfer catalyst (PTC), and operational conditions. The developed Neural Network model demonstrated the best performance in predicting PET conversion, with a testing determination coefficient (R^{2 …}

Advancing Temperature Monitoring Of The Bottom Anode In A Direct Current Electric Arc Furnace Operations With Distributed Optical Fiber Sensors., Ogbole Collins Inalegwu, Rony Kumer Saha, Yeshwanth Reddy Mekala, Farhan Mumtaz, Nicholas Dionise, Zane Voss, Jeffrey D. Smith, Ronald J. O'Malley, Rex E. Gerald, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

The bottom anode in the Direct Current Electric Arc Furnace (DC EAF) is critical for completing the electrical circuit necessary for sustaining the arc within the furnace. For pin-type bottom anodes, monitoring of the temperature of select pins instrumented with thermocouples is performed to track bottom wear in the EAF and inform the operator when the furnace should be removed from service. This work presents the results from a plant trial using distributed temperature monitoring of bottom anode pins in a 165-ton DC EAF over a two-month service period utilizing two optical fiber sensing techniques: fiber Bragg grating (FBG) and …

Discrimination Of Temperature And Strain By Characterizing Two Femtosecond Laser-Written Coincident Sapphire Fiber Bragg Gratings For Harsh Environment Applications, Farhan Mumtaz, Bohong Zhang, Koustav Dey, Jeffrey D. Smith, Ronald J. O'Malley, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

In this study, two co-incident sapphire fiber Bragg gratings (SFBGs) were successfully inscribed utilizing a femtosecond (fs) laser to achieve a high fringe contrast interferogram. These two SFBGs employ a unique configuration, one parallel to the center axis, called p-SFBG, and the other forming an angle from the center-axis, called a-SFBG, allowing for simultaneous strain and temperature measurements with low crosstalk. As a proof of concept, p-SFBG and a-SFBG using line-by-line method are characterized, which are shorter in length (i.e., 1.5 mm), producing reflectivity of ~3dB. This effort demonstrates the use of two coincident SFBGs forming an angle of 2.29° …

Characterization And Deportment Of Anode Impurities In Copper Electrorefining, Charles Michael Campbell

Doctoral Dissertations

The objective of this research was to study the deportment of the group 15 elements, arsenic, antimony and bismuth during copper electrorefining. Samples were collected from six industrial copper anodes with different compositions. Specimens were physically characterized and electro refined to understand the differences in the behavior of selected impurities. Inclusions in the cast metal structures were characterized using automated scanning electron microscopy and energy dispersive spectroscopy to measure and correlate their size, shape and composition. Arsenic and lead were found to have a positive correlation between concentration and size of inclusions. Using wavelength dispersive spectroscopy, multiphase inclusions were examined, …

Effect Of Thermomechanical Processing And Heat Treatment On The Microstructure And Mechanical Properties Of Ultra-High Strength Steels, Rogerio Antao Cardoso

Doctoral Dissertations

"A martensite-based and an austenite-based Fe-Mn-Al steels were investigated aiming the pilot-scale production of steels that meet military specifications for Rolled Homogeneous Armor (RHA) and High-hardness Armor (HHA) plates. Each material underwent specific thermomechanical processes and the following hardness, Charpy V-notch (CVN) impact toughness at -40 °C and room-temperature tensile properties were correlated with the resulting microstructures.

Specimens of the martensitic steel were austenitized at 1010 °C, quenched and tempered at 150, 175, 200, 225 and 250 °C for times up to four hours. As for the Fe-Mn-Al steel, its hot rolling schedule was design to promote strain accumulation in …

Processing And Densification Of Multi-Phase High-Entropy Ceramics, Steven Smith

Doctoral Dissertations

"This work focuses on the processing and densification of multiphase, high-entropy ceramics to promote their use in friction stir welding technologies. Several high-entropy systems including high-entropy borides, carbides, and their composites were produced. Boro/carbothermal and carbothermal synthesis were used to produce high-entropy powders from oxide powder mixtures. Composites of high-entropy borides and high-entropy carbides were produced using a sequential approach to produce both phases. The carbide was first produced using carbothermal reduction, then ZrH2 and B4C were added to the carbide powder to produce the high-entropy boride phase. The resulting powder was densified by spark plasma sintering and pressureless sintering, …

The Structure, Properties And Dissolution Behaviors Of Phosphate Glasses, Han Zhang

Doctoral Dissertations

The poor chemical durability remains a critical challenge for the application of phosphate glasses. This study investigates the compositional influences on the structure, properties and chemical durability of Li2O-ZnO-P₂O₅ glasses. Their structural characteristics were analyzed utilizing high-performance liquid chromatography, Raman spectroscopy, and X-ray photoelectron spectroscopy. The incorporation of (Li2O+ZnO) in LZeq glasses depolymerizes the phosphate network. In LZ40P and LZ45P glasses, Li⁺ initially replaces Zn²⁺ associated with non-bridging oxygens (NBOs) in Q² tetrahedra. Once the substitution in Q² is complete, further Li⁺ incorporation leads to the replacement of Zn²⁺ in Q^{1 …}

Investigating The Effects Of Fly Ash On The Properties Of Silica-Deficient High Alumina Materials, Sai Akshay Ponduru

Doctoral Dissertations

This research is made up of five studies mainly focused on attaining sustainability in high alumina cements like calcium aluminate cement (CAC) and calcium sulfoaluminate belite cements (CSAB) by partially replacing them with additives and supplementary cementitious materials (SCMs) like fly ash (FA). The first study focused on understanding the reaction kinetics of CAC and FA binders at different replacement levels (i.e. between 10%-to-50% by mass) and their effect on mechanical properties. It was also shown that the reactive nature of FAs can be determined by calculating a single parameter called number of constraints (nc) derived from topological constraint theory. …

Distributed Sapphire Fiber Bragg Grating-Based Thermal Profiling Of Submerged Entry Nozzles, Farhan Mumtaz, Hanok W. Tekle, Bohong Zhang, Xiaodong Li, Sunday Abraham, Bryant Mathis, Jeffrey D. Smith, Ronald J. O'Malley, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This article focuses on the application of sapphire fiber Bragg gratings (FBGs) for instrumentation in submerged entry nozzles (SENs) within the steelmaking industry. The SEN is pivotal for transferring molten steel from a tundish to a mold, while preventing the infiltration of oxygen and nitrogen from the surrounding environment. Maintaining optimal flow conditions in the mold is crucial for ensuring casting process stability and maintaining high-quality steel. Sapphire FBG sensors have been instrumented in SENs to enable distributed thermal mapping for monitoring the health of the SEN. The optical sensor comprises three cascaded sapphire FBGs inscribed using femtosecond (FS) laser …

High-Frequency Gold Price Forecasting: Optimizing Multi-Layer Perceptron With Genetic Algorithm, Vrtagic Sabahudin, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Accurately forecasting gold price actions is critical in financial markets due to gold's role as a safe-haven asset. This paper addresses the challenge of forecasting gold prices by applying a Genetic Algorithm (GA) with a Multi-Layer Perceptron (MLP) model. The research exploits historical financial data from various instruments, including gold futures, Bitcoin, and key currency pairs, to improve prediction accuracy. By optimizing the MLP's hyper parameters through GA, the model efficiently captures complex relationships in high-frequency data, achieving a remarkable R² score of 0.9993. This level of precision demonstrates the model's potential for providing actionable insights for traders and investors. …

Zeolite 13x Particles With Porous Tio2 Coating And Ag2o Nanoparticles As Multi-Functional Filler Materials For Face Masks, Wei Su, Kaiying Wang, Han Yu, Fateme Fayyazbakhsh, Jeremy Watts, Yue-Wern Huang, Jee-Ching Wang, Xinhua Liang

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Adsorbent components in face masks are crucial for protecting individuals exposed to dangerous situations. In this study, one porous TiO₂ layer was deposited on zeolite 13X particles by coating hybrid organic/inorganic titanium alkoxide film via molecular layer deposition (MLD), followed by heat treatment to remove organic components in the MLD film. Various concentrations of Ag₂O nanoparticles were impregnated on the TiO₂-coated 13X particles, offering a wide range of antibacterial, antifungal, and antiviral characteristics. The obtained composite particles were characterized using X-ray photoelectron spectroscopy and thermal gravimetric analysis to study the composition and mass loading of …

Complex Precipitation Behavior In A Co-Free High Entropy Alloy During Aging, Matthew Luebbe, Fan Zhang, Jonathan D. Poplawsky, Jiaqi Duan, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

High entropy alloys (HEAs) demonstrate high strength, thermal stability, and irradiation resistance, making them desirable for applications in nuclear reactors and other harsh environments. Many existing HEAs contain cobalt (Co), which makes them unsuitable for nuclear applications due to the long-term activation of Co. A previously studied Co-free alloy, (Fe_0.3Ni_0.3Mn_0.3Cr_0.1)₈₈Ti₄Al₈, exhibits high strength but compromised ductility due to its network of brittle precipitates upon aging. This work investigates the formation mechanism and evolution of the precipitates, including L1₂ (Ni₃Ti type, ordered face-centered cubic …

Multiphysics Modeling And Experimental Validation Of High-Strength Steel In Laser Powder Bed Fusion Process, M. Rangapuram, S. Babalola, J. W. Newkirk, L. N. Bartlett, F. W. Liou, K. Chandrashekhara, Stephen R. Cluff

Materials Science and Engineering Faculty Research & Creative Works

Laser powder bed fusion (LPBF) is a subset of the additive manufacturing process in which a laser beam selectively joins the metal powder into a desired part in a sequential layer process. Owing to its complex nature of rapid heating and cooling of the melt pool, there is a need to understand the melt pool behavior and its effects on the final manufactured part. a densely packed powder bed is highly desirable for fabricating a superior part using the LPBF process. in this work, discrete element model was used to generate powder beds with realistic powder properties and various factors …

Experimental Evaluation Of A Recrosslinkable Co2-Resistant Micro-Sized Preformed Particle Gel For Co2 Sweep Efficiency Improvement In Reservoirs With Super-K Channels, Adel Alotibi, Tao Song, Ali Al Brahim, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

A recross linkable CO₂-resistant branched preformed particle gel (CO₂-BRPPG) was developed for controlling CO₂ injection conformance, particularly in reservoirs with super-permeable channels. Previous work focused on a millimeter-sized CO₂-BRPPG in open fractures, but its performance in high-permeability channels with pore throat networks remained unexplored. This study used a sand pack model to evaluate a micro-sized CO₂-BRPPG under varying conditions of salinity, gel concentration, and pH. at ambient conditions, the equilibrium swelling ratio (ESR) of the gel reached 76 times its original size. This ratio decreased with increasing salinity but remained stable …

Estimating The Possible Qpos Of M87* From The Parameters Of A Hairy Kerr Black Hole, Orhan Donmez, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

In this paper, we study the dynamics of the shock cone formed around a hairy Kerr black hole due to Bondi– Hoyle–Lyttleton (BHL) accretion and investigate the quasi-periodic oscillations (QPO) behaviors resulting from the black hole-cone interaction, aiming to predict the QPO frequencies that may occur around the M87∗ black hole. To achieve this, we use the hairy Kerr black hole parameters consistent with the observed shadow parameters of M87∗ as initial conditions in numerical simulations, revealing the structure of the resulting shock cone and QPOs in a strong gravitational field. Numerical calculations show that the deviation of …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO2, MoS2, and Al2O3) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment of 10 °C. Obtained results showed that thermal …

Hafnium Oxide Coating To Improve The Oxidation Behavior Of Zirconium Diboride, Jan E. Förster, William G. Fahrenholtz, Gregory E. Hilmas, Ravisankar Naraparaju

Materials Science and Engineering Faculty Research & Creative Works

Hafnium dioxide (HfO₂) coatings were successfully deposited on zirconium diboride (ZrB₂) using reactive magnetron sputtering. After the oxidation at 1500°C or 1600°C, the mutual dissolution of HfO₂ and thermally grown ZrO₂ was observed which has resulted in the formation of a mixed oxide zone. As the enrichment of the mixed oxide zone by ZrO₂ progresses, monoclinic/tetragonal phase transition temperature of ∼1790°C for nominally pure HfO₂ moves towards ∼1500 °C. Finally, the inevitable phase transition from monoclinic to tetragonal structure results in the development of cracks, pores, and gaps within the mixed oxide …

Machine Learned Interatomic Potentials For Ternary Carbides Trained On The Aflow Database, Josiah Roberts, Biswas Rijal, Simon Divilov, Jon Paul Maria, William G. Fahrenholtz, Douglas E. Wolfe, Donald W. Brenner, Stefano Curtarolo, Eva Zurek

Materials Science and Engineering Faculty Research & Creative Works

Large-density functional theory (DFT) databases are a treasure trove of energies, forces, and stresses that can be used to train machine-learned interatomic potentials for atomistic modeling. Herein, we employ structural relaxations from the AFLOW database to train moment tensor potentials (MTPs) for four carbide systems: CHfTa, CHfZr, CMoW, and CTaTi. The resulting MTPs are used to relax ~6300 random symmetric structures and are subsequently improved via active learning to generate robust potentials (RP) that can relax a wide variety of structures, and accurate potentials (AP) designed for the relaxation of low-energy systems. This protocol is shown to yield convex hulls …

A General Model For The Ductility Of Intermetallics Applied To Fe-Co Alloys, Wesley Everhart, Joseph Newkirk

Materials Science and Engineering Faculty Research & Creative Works

The mechanical properties, specifically ductility, of high performing soft magnets such as Fe-Co alloys are a limiting factor to their broader use in a number of systems. The understanding of the mechanical robustness in these materials is currently insufficient to be able to support the growing interest in applications such as magnetic shielding or electric motors. Fe-Co alloys provide the highest commercially available magnetic saturation and high magnetic permeability but have very poor ductility. The addition of vanadium to these alloys has allowed for significant commercialization and some ductility improvements, but the fundamental reasons for the observed improvements are not …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-Based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO₂, MoS₂, and Al₂O₃) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment …

Synthesis And Properties Of (Hf,Mo,Ti,W,Zr)B2–(Hf,Mo,Ti,W,Zr)C Dual Phase Ceramics, S. Filipović, S. M. Smith, G. Hilmas, W. Fahrenholtz, N. Obradović, S. Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Dense, dual phase (Hf,Mo,Ti,W,Zr)B₂–(Hf,Mo,Ti,W,Zr)C ceramics were synthesized with varying contents of Mo and W. The final (Hf_0.317Mo_0.025Ti_0.317W_0.025Zr_0.317)C–(Hf_0.317Mo_0.025Ti_0.317W_0.025Zr_0.317)B₂ was a nominally pure, dual phase ceramic, while compositions with higher amounts of Mo and W contained multiple phases. The final microstructures had submicron grains due to pinning effects. Vickers hardness values were up to 48.6 ± 2.2 GPa for an applied load of 0.49 N for the ceramic with optimized composition and densification. The solubility limits for Mo and …