Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Missouri University of Science and Technology

Discipline
Keyword
Publication Year
Publication
Publication Type

Articles 1741 - 1770 of 2244

Full-Text Articles in Materials Science and Engineering

Evaporation And Condensation Of Zinc, Shailesh Bhanuprasad Vora Jan 1971

Evaporation And Condensation Of Zinc, Shailesh Bhanuprasad Vora

Masters Theses

"Evaporation rates of liquid zinc were determined experimentally within the temperature range of 450º C to 575º C and at argon pressures ranging from 730mm Hg to 130mm Hg. Extrapolated values of these rates are found to be consistent with the previously reported rates obtained by St. Clair and Spendlove at lower pressures. Between 100 microns and one atmosphere pressure rates of evaporation seem to vary according to an equation of the form W = APᴮ, where Pis pressure and, A and B are constants. Similar experiments were performed with brass powders in atmospheres of argon and helium at temperatures …

Go to article

Alkali Mobility And Mechanical Relaxation In Mixed-Alkali Silicate Glasses, James W. Fleming Jr. Jan 1971

Alkali Mobility And Mechanical Relaxation In Mixed-Alkali Silicate Glasses, James W. Fleming Jr.

Masters Theses

"Internal friction and sodium and potassium self-diffusion coefficients for (1-X)Na₂O · XK₂O· 3SiO₂ glasses were measured. Alkali diffusion was measured between 300 and 500ºC using radioactive isotopes and a thin-sectioning technique. Internal friction was measured from room temperature to 500ºC, 0.1 to 2000 Hz. Comparison between alkali diffusion and internal friction data for Na-K glasses with those for other mixed-alkali glasses shows that the mixed-alkali peak is related to alkali mobility. It is concluded that the mechanism for mixed-alkali internal friction is a cooperative rearrangement of dissimilar alkali ions, with the slower moving ion controlling the rate of reorientation"--Abstract, page …

Go to article

Electrolytic Reduction Of Zinc From Acidic Sulfate Solutions, Kenneth Dale Gielow Jan 1971

Electrolytic Reduction Of Zinc From Acidic Sulfate Solutions, Kenneth Dale Gielow

Masters Theses

"Cathode polarization curves were obtained for the electrodeposition of zinc from sulfate solutions with pH 2 and zinc concentrations of 10.0, 40.0, 80.0, and 100.0 gpl zinc. Both pure zinc and pure aluminum were used as cathodes with some difference in results noted. The effect of animal glue additions of 0.01, 0.10, and 0.50 gpl of solution on the cathodic polarization curves and the resulting deposit morphologies were determined. These glue additions correspond to 0.20, 2.0, and 10.0 pounds of glue per ton of zinc deposited, respectively. The slope of the Tafel region of the polarization curves was found to …

Go to article

A Study Of The Void-Strengthening Of Aluminum And Its Nature, Purushottam G. Manusmare Jan 1971

A Study Of The Void-Strengthening Of Aluminum And Its Nature, Purushottam G. Manusmare

Masters Theses

"Strengthening of aluminum by formation of the voids and the nature of resultant strengthening, viz., the temperature and the strain rate dependence of its yield strength were studied. Aluminum wires with 99.999% purity and of 3.1 mm diameter were quenched and heat treated to form voids of the approximate density 10¹³-10¹⁴ voids/cm³ and were tested for their yield strength. Voids in selected samples were observed by transmission electron microscopy using the Hitachi HU-11A microscope. The yield strength of the void strengthened samples was measured at various temperatures from 77ºK to 593ºK using two strain rates, 3.33 x 10⁻²/sec and 1.67 …

Go to article

The Genesis Of Cellular Precipitation In Copper Rich Copper-Indium Alloys, Raymond Albert Fournelle Jan 1971

The Genesis Of Cellular Precipitation In Copper Rich Copper-Indium Alloys, Raymond Albert Fournelle

Doctoral Dissertations

"The morphology of cellular precipitation in a Cu-9.5at.%In alloy has been investigated by light and electron microscopy and x-ray and electron diffraction. Both cellular and general precipitation were observed to occur simultaneously in quenched and aged alloys while only cellular precipitation was observed to occur in isothermally aged alloys. Because of the presence of wide, vacancy depleted precipitate free zones in the vicinity of grain boundaries, general precipitation was observed to have no effect on the early development of cellular precipitation. Hence, the early development of cellular precipitation was found to be identical for both types of heat treatment. By …

Go to article

High Temperature Compressive Creep In Mullite, Peter C. Smith Jan 1971

High Temperature Compressive Creep In Mullite, Peter C. Smith

Masters Theses

"Compressive creep measurements were made on two groups of mullites at temperatures between 1455ºC and 1520ºC. The first group consisted of commercially manufactured mullites. The second group was made up of 7 different mullite compositions spanning the alumina-silica solid solution range from 3Al₂O₃ • 2SiO₂ to 2Al₂O₃ • SiO₂ . Thermal activation energies and stress exponents were calculated for the mullites in the second group. Steady state strain rates taken at 1460ºC under loads of 100 and 110 psi varied between 1.3x10⁻⁴ in/in/hr and 15.4x10⁻⁴ in/in/hr. Activation energies were between 109 Kcal/mole and 204 Kcal/mole. Stress exponents calculated from data …

Go to article

An Age Hardening Study Of Magnesium-Thorium-Manganese Alloys, Kuldip Singh Chopra Jan 1971

An Age Hardening Study Of Magnesium-Thorium-Manganese Alloys, Kuldip Singh Chopra

Doctoral Dissertations

"The age hardening processes in Mg-3.5 wt.% Th-1.0 wt.% Mn and Mg-1.0 wt.% Th-1.0 wt.% Mn alloys have been studied by light and electron microscopy, and by electron and X-ray diffraction. At aging temperatures of 300ºC and below, G.P. zone formation rapidly hardens these alloys followed by the precipitation of disc shaped plates during averaging. During aging above 300ºC, no G.P. zones form and the disc shaped precipitate grows to very large sizes. The combined results of X-ray and electron diffraction indicate that the disc shaped precipitate has a Mg₃Cd (DO₁₉) type structure. The basal plane of the Mg₃Th discs …

Go to article

Surface Reactions Of Boron With Clean Tungsten Substrates, Thomas A. Flaim Jan 1971

Surface Reactions Of Boron With Clean Tungsten Substrates, Thomas A. Flaim

Doctoral Dissertations

"A model developed to predict adsorbate-induced work-function changes for thermionic emitters is shown here to apply to a more general class of electron emission phenomena and a much broader range of adsorbates. This model predicts that chemically, vapor-deposited boron will increase the work function of a clean tungsten substrate at coverages between 0 and 1 monolayer. This is the first time that a single model has been shown to predict both positive and negative work function changes for different adsorbates. The reactions of chemically, vapor-deposited (CVD) boron with clean tungsten substrates were studied using field emission microscopy (FEM) and low …

Go to article

Internal Friction Of Ion Exchanged Li₂O•Al₂O₃•2sio₂ Glasses, A. Ismail A. Abdel-Latif Jan 1971

Internal Friction Of Ion Exchanged Li₂O•Al₂O₃•2sio₂ Glasses, A. Ismail A. Abdel-Latif

Doctoral Dissertations

"Li₂O•Al₂O₂•2SiO₂ glass fibers were ion-exchanged from 1 to 300 minutes in a sodium nitrate bath at 366ºC. The internal friction was measured along with the lithium and sodium concentration profiles. As sodium progressively replaced lithium, the alkali internal friction peak became smaller while a new peak (mixed alkali peak) appeared and increased in magnitude. These changes in the internal friction are similar to those that occur upon the addition of a second alkali to glasses prepared by conventional melting. The magnitude of both internal friction peaks in ion exchanged glasses was dependent on the overall glass composition. The magnitude of …

Go to article

Anodic Dissolution Of Beryllium In Anhydrous Media, William Joseph James, Martin E. Straumanis Jan 1971

Anodic Dissolution Of Beryllium In Anhydrous Media, William Joseph James, Martin E. Straumanis

Chemistry Faculty Research & Creative Works

No abstract provided.

Go to article

The Pm3m-Fm3m Transformation And Phase Equilibrium In Solid Solutions Of Csc1 With Kc1, Rbc1, And Csbr, John David Weyand Jan 1971

The Pm3m-Fm3m Transformation And Phase Equilibrium In Solid Solutions Of Csc1 With Kc1, Rbc1, And Csbr, John David Weyand

Masters Theses

"Thermal expansion and the Pm3m t Fm3m transition of cesium chloride have been studied with high temperature diffractometry, differential thermal analysis, and heating and quenching techniques. The onset temperature of the transition in pure CsCl, on heating, is 471ºC. There are no observable premonitory effects below the transition temperature and no apparent structural relationships between the polymorphs is apparent. Both phases coexist over a 20º to 50ºC temperature range and equilibrium thermal hysteresis occurs on heating and cooling. Hysteresis behavior is explained by addition of strain energy parameters to the free energy function. Initiation of the Pm3m t Fm3m transformation …

Go to article

Final Sintering Of Cr₂O₃ With Minor Additions Of Mgo And Sintering Of Mgo With Minor Additions Of Cr₂O₃, Gordon E. Jungquist Jan 1971

Final Sintering Of Cr₂O₃ With Minor Additions Of Mgo And Sintering Of Mgo With Minor Additions Of Cr₂O₃, Gordon E. Jungquist

Masters Theses

"The effect of oxygen activity on the sintering of Cr₂O₃ with minor additions of MgO, and of MgO with minor additions of Cr₂O₃ at 1600ºC was investigated. A peak density (99.4% of theoretical) was obtained for high purity Cr₂O₃ by maintaining the equilibrium oxygen partial pressure needed to maintain the Cr₂O₃ phase. The addition of 0.1 wt. % MgO increased the sintered density at the same oxygen pressure to 99.8%. Further MgO additions decreased the density. The density of pure MgO was independent of the PO₂ over the range investigated. Addition of Cr₂O₃ to MgO decreased the density at …

Go to article

A Magnetic Aftereffect In Dilute H.C.P. Co-C Alloys, J. R. Keiser, Manfred Wuttig Jan 1971

A Magnetic Aftereffect In Dilute H.C.P. Co-C Alloys, J. R. Keiser, Manfred Wuttig

Materials Science and Engineering Faculty Research & Creative Works

A magnetic Dis accommodation in dilute h.c.p. Co-C alloys has been observed around 90°C. The thermally activated process giving rise to the Dis accommodation is characterized by an activation energy of 26 kcal mole-1 and an attack frequency on the order of 10+13 sec-1. An application of the selection rules shows that the Dis accommodation cannot be caused by the redistribution of tetrahedral or octahedral interstitials or any nearest neighbor interstitial pairs as long as the defects interact linearly with the internal magnetic field. © 1971.

Go to article

On The Activation Entropy Of Interstitial Diffusion In B.C.C. Iron, Manfred Wuttig Jan 1971

On The Activation Entropy Of Interstitial Diffusion In B.C.C. Iron, Manfred Wuttig

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Go to article

Mixed‐Cation Effect In Silver Borate Glasses, E. N. Boulos, N. J. Kreidl Jan 1971

Mixed‐Cation Effect In Silver Borate Glasses, E. N. Boulos, N. J. Kreidl

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Go to article

The Anodic Dissolution Reaction Of Insb: Etch Patterns, Electron Number, Anodic Disintegration, And Film Formation, Martin E. Straumanis, Lih Da Hu Jan 1971

The Anodic Dissolution Reaction Of Insb: Etch Patterns, Electron Number, Anodic Disintegration, And Film Formation, Martin E. Straumanis, Lih Da Hu

Materials Science and Engineering Faculty Research & Creative Works

The etching behavior of the inverse {111} planes of undoped, semiconducting, n-type, InSb single crystals was explored. Depending upon the etchant, including anodic dissolution, various etch patterns were obtained on the inverse planes. In general, the etch pits on the In{111} plane were round, and the face was shiny, whereas the face of the inverse plane was dark and rough. The rates of dissolution in the electrolytes used were very low, especially in absence of oxidizers. The components dissolve as In3+ and Sb3 +. At current densities above 40 or 60 mA cm-2 (on Sb{111} or In{111}), growth of a …

Go to article

Stored Energy Of Room Temperature Deformed Copper, G. J. Filatovs, Hollis P. Leighly Jan 1971

Stored Energy Of Room Temperature Deformed Copper, G. J. Filatovs, Hollis P. Leighly

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Go to article

Thermal Expansion Of Pb3o4, Charles A. Sorrell Jan 1971

Thermal Expansion Of Pb3o4, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

Thermal expansion of Pb3O4 was investigated by high‐temperature X‐ray diffraction. The coefficient in the a0 direction is 14.6x10−6/°C. Expansion in the c0 direction is 32% greater, with a coefficient of 19.3x10−6/°C. Coefficients of expansion are linear from 25° to 490°C and are comparable with those of tetragonal and orthorhombic PbO. Copyright © 1971, Wiley Blackwell. All rights reserved

Go to article

Structure And Properties Of Silver Borate Glasses, E. N. Boulos, N. J. Kreidl Jan 1971

Structure And Properties Of Silver Borate Glasses, E. N. Boulos, N. J. Kreidl

Materials Science and Engineering Faculty Research & Creative Works

Clear glasses form in the system Ag2O‐B2O3 up to about 35 mol% (65 wt%) Ag2O. Infrared absorption, thermal expansion, and density data indicated an analogy to the Na2O‐B2O3 system. Pentaborate‐triborate group pairs appear to be formed on addition of Ag2O to B2O3 up to 20 mol% Ag2O and diborate groups from 20 to 33 mol% Ag2O. This interpretation is supported by the comparison of the infrared absorption spectra of quenched and crystallized glasses. One crystallization product, Ag2O‐4B2O3, was …

Go to article

Activation Volumes Of Interstitial Diffusion In Ferromagnetic Metals And Alloys, Manfred Wuttig, J. Keiser Jan 1971

Activation Volumes Of Interstitial Diffusion In Ferromagnetic Metals And Alloys, Manfred Wuttig, J. Keiser

Materials Science and Engineering Faculty Research & Creative Works

The Dis accommodation technique was used to determine the activation volumes of carbon diffusion ΔV of a Fe-1.4 wt% Si alloy, of hcp cobalt, and of nickel at the temperatures of -21, 75, and 110°C, respectively. The obtained values of ΔV are +0.3 ± 0.3 and -0.6 ± 0.9 cm3 mole-1 for the two relaxations observed in hcp cobalt, and 1.2 ± 0.1 cm3 mole-1 for nickel. These results are discussed in terms of a continuum model that interprets the activation energy of diffusion as a sum of the strain and exchange energies. It is found that in ferromagnetic solids …

Go to article

Activation Volumes Of Carbon Diffusion In F.C.C. Iron-Nickel Alloys, James Raymond Keiser Jan 1971

Activation Volumes Of Carbon Diffusion In F.C.C. Iron-Nickel Alloys, James Raymond Keiser

Doctoral Dissertations

"The disaccommodation technique was used to determine the activation volume of carbon diffusion, ΔV, in six fcc iron-nickel alloys. Measurements were made at temperatures ranging from 68ºC to 90ºC and pressures up to six kilobars on samples having a nickel content between 31 and 63 at. %. A maximum activation volume of 3.9 cm³/mole was found at 34 at. % nickel. The compositional dependence of ΔV is satisfactorily reproduced by a magnetic energy continuum model in which it is assumed that the activation free energy of diffusion is essentially ferromagnetic in origin "--Abstract, page iii.

Go to article

The Effect Of 15% Mno On The Phase Relations In The System Cao-Feo-Sio₂ At 1450ºc, Aquil Ahmad Jan 1971

The Effect Of 15% Mno On The Phase Relations In The System Cao-Feo-Sio₂ At 1450ºc, Aquil Ahmad

Masters Theses

"A study was made of the phase relations at 1450ºC in the systems CaO-FeO-SiO₂ and CaO-FeO-SiO₂ -15% MnO, in equilibrium with metallic iron. The stability region of different phases was determined by microscopic examination and electron-beam microprobe analysis of the quenched specimens. The effect of 15% MnO on the liquid saturation boundary of the system CaO-(FeO+MnO)-SiO₂ was discussed in terms of the effect of MnO on slag making reactions in the Basic Oxygen Furnace steelmaking process"--Abstract, page ii.

Go to article

Quenching Defects In Aluminum Plus Ten Atomic Per Cent Zinc, James Thomas Grider Jan 1971

Quenching Defects In Aluminum Plus Ten Atomic Per Cent Zinc, James Thomas Grider

Masters Theses

"This study was undertaken to resolve the conflict which has recently arisen as to the as-quenched microstructure in the Al-Zn system as revealed by thin film transmission electron microscopy. The composition range of most active study has been that from 5 to 15 atomic per cent Zn in superpurity AL. Consequently a composition of 10 atomic per cent Zn was chosen for this study. There are no discontinuties in the phase diagram in this composition range which would influence the above choice. It exists as a single phase solid solution at high temperatures and as a two phase alloy at …

Go to article

Phase Equilibrium And Thermodynamic Study Of The Iron-Copper-Carbon System, Krishna Parameswaran Jan 1971

Phase Equilibrium And Thermodynamic Study Of The Iron-Copper-Carbon System, Krishna Parameswaran

Masters Theses

"Gas carburization experiments were conducted at 950ºC in order to study the phase relations and to determine the activity of carbon in the iron-rich corner of the iron-copper-carbon system. The solubility of graphite in equilibrium with iron-copper alloys was determined at 950º, 1000º, and 1050ºC. The results of gas carburization and graphite solubility experiments at 950ºC were used in constructing an isothermal section of the iron-rich end of the iron-copper-carbon phase diagram, on which are superimposed carbon isoactivity lines. Graphite solubility data at 1000º and 1050ºC were used to construct similar diagrams without the isoactivity lines. The effect of carbon …

Go to article

A Study Of The Dislocation Instability And Reverse Martensitic Transformation In Fe-Ni System, Chung Lim Jan 1971

A Study Of The Dislocation Instability And Reverse Martensitic Transformation In Fe-Ni System, Chung Lim

Masters Theses

"Since the martensitic reaction is a strain transformation, the transformation of the lattice structure can be induced by an external stresses. This also means that the macroscopic total elastic constant should decrease as the temperature is lowered to Ms on cooling. For the reverse transformation an anomalous decrease of the elastic constant is to be expected as the temperature increases to As on heating. In this experiment measurements of the velocity change of an ultrasonic wave in Fe-Ni alloys were carried out for the reverse martensitic transformation. The deviation from the linear relationship of the velocity change as …

Go to article

Thermal Expansion Of Tungsten At Low Temperatures, Jayant S. Shah, Martin E. Straumanis Dec 1970

Thermal Expansion Of Tungsten At Low Temperatures, Jayant S. Shah, Martin E. Straumanis

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Go to article

Diffusion In Wide Grain Boundaries, J. Mimkes, Manfred Wuttig Dec 1970

Diffusion In Wide Grain Boundaries, J. Mimkes, Manfred Wuttig

Materials Science and Engineering Faculty Research & Creative Works

The rigorous solution of the grain-boundary diffusion problem has been approximated by a series expansion method. The calculations show that higher-order terms may be neglected in the bulk adjacent to the grain boundary. Thus, in this region Whipple's and Suzuoka's solutions represent a close approximation to the problem. Inside the grain boundary, however, higher-order approximations have to be taken into account. These approximations gain importance in the case of wide grain boundaries. The solutions obtained for an instantaneous source have been fitted to available grain-boundary diffusion data of Ni2+ in MgO at 1200°C. Numerical calculations give for the bulk diffusion …

Go to article

Phase Equilibria And Thermodynamic Studies In The System Cao-Feo-Fe2o3-Sio2, M. Timucin, Arthur E. Morris Nov 1970

Phase Equilibria And Thermodynamic Studies In The System Cao-Feo-Fe2o3-Sio2, M. Timucin, Arthur E. Morris

Materials Science and Engineering Faculty Research & Creative Works

Phase equilibria and thermodynamic properties of the system CaO-FeO-Fe2O3-SiO2 were studied at 1450° and 1550°C, over a range of pO2 from 1 to about 10-11 atm. Isothermal phase diagrams and activity-composition diagrams were constructed for 0, 5, 10, 20, and 30 wt pct SiO2 sections. The data are applicable to further understanding the behavior of simple BOF steelmaking slags. © 1970 The Minerals, Metals & Materials Society - ASM International - The Materials Information Society.

Go to article

The Fe-Ho Binary System, G. J. Roe, Thomas J. O'Keefe Sep 1970

The Fe-Ho Binary System, G. J. Roe, Thomas J. O'Keefe

Materials Science and Engineering Faculty Research & Creative Works

The Fe-Ho phase diagram was determined on the basis of data obtained by X-ray diffraction, metallographic and differential thermal analysis techniques. Since emphasis was centered in the region where intermetallic compounds predominate, neither the iron nor holmium terminal regions were included in this study. Eutectic reactions were found to occur at 16.5 wt pct Fe and 875° C, 61 wt pct Fe and 1284° C, and 79 wt pct Fe and 1338° C. The congruent melting points of the compounds Ho6Fe23 and Ho2Fe17 were found to be 1332° and 1343° C, respectively. Two other intermetallic compounds were found, HoFe2 and …

Go to article

Electron Emitter Tips And Method, P. D. Ownby Mar 1970

Electron Emitter Tips And Method, P. D. Ownby

Materials Science and Engineering Faculty Research & Creative Works

Boron is deposited on the (110) plane facet at the center of a tungsten electron emitter tip by chemical vapor deposition of boron triiodide. The emission current density is greatest in the center of the emitting area (FIG. 2).

Go to article

First Prev Next Last