Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Chinese Chemical Society | Xiamen University

Articles 1201 - 1230 of 1829

Full-Text Articles in Materials Science and Engineering

Recycling Of The Spent Nickel-Cadmium Batteries Based On Bioleaching Process, Liang-Shu Xia, Shi-Fu Fu, Zhong-Qing Chen Aug 2006

Recycling Of The Spent Nickel-Cadmium Batteries Based On Bioleaching Process, Liang-Shu Xia, Shi-Fu Fu, Zhong-Qing Chen

Journal of Electrochemistry

Less than 1 percent of discarded dry batteries are recovered in china.it is necessary to find an economic,fast and environmentally friendly process to recycle spent dry batteries.Bioleaching is better one of the few technology applied for the recovery of the toxic metals from hazardous spent batteries.In this study,after the acidified sludge made by the inoculated and cultured indigenous sewage sludge was acted as leaching bacteria species,the influence of the different pH values,the different residence time of the sludge in bioreactor(RTB),the leaching time,whether or not adding Fe(iron powder) to the leaching liquid on the leaching rate of Ni,Cd was tested.The results …

Go to article

The Property Study Of Libob-Pc/Dec Electrolyte, Ying-Kun Ning, Bi-Tao Yu, Fu-Shen Li, Wei-Hua Qiu Aug 2006

The Property Study Of Libob-Pc/Dec Electrolyte, Ying-Kun Ning, Bi-Tao Yu, Fu-Shen Li, Wei-Hua Qiu

Journal of Electrochemistry

The new electrolyte salt LiBOB for Li-ion battery was synthesized in laboratory,and series of electrolytes of LiBOB and PC/DEC was compounded.The conductivity of the electrolytes was compared by changing the temperature and concentration.The cycling performance of charging-discharging was also compared by the charging-discharging test,the results showed that the varying regularity of conductivities and cycling stability and capacity were not always identical,but there were a suitable electrolyte for Li/ARG cell.The A.C.impedance and CV were used to test the compatibility of the most suitable electrolyte and ARG anode.Conclusion can be drawn that the ARG anode can be protected very well by SEI …

Go to article

Investigations On Electrochemical Characteristics Of Liv3O8 Electrode In Lithium Sulfate-Water-Ethanol Electrolytes, An-Bao Yuan, Wei-Xiang Song Aug 2006

Investigations On Electrochemical Characteristics Of Liv3O8 Electrode In Lithium Sulfate-Water-Ethanol Electrolytes, An-Bao Yuan, Wei-Xiang Song

Journal of Electrochemistry

The active material of LiV3O8 prepared using low-temperature pre-reaction in solution followed by intermediate-temperature calcination at 450 ℃.The product was characterized by X-ray diffraction analysis and scanning electron microscope observation.The performance of LiV3O8  electrode in neutral lithium sulfate-water-ethanol electrolytes was investigated using electrochemical methods.Galvanostatic charge/discharge results indicated that the specific capacity of LiV3O8  electrode decreases with ethanol content increasing in electrolyte.The most appropriate water/ethanol volumetric ratio is 4 ∶1 in terms of conductivity of the electrolyte and stability of the electrode.AC impedance measurements demonstrated that the ohmic resistance of the electrolyte …

Go to article

Studies On Performance And Electrode Materials For All Vanadium Flow Battery, Jun Yuan, Qing-Chun Yu, Yi-Feng Liu, Liang-Liang Ma, Yi-Hua Wu Aug 2006

Studies On Performance And Electrode Materials For All Vanadium Flow Battery, Jun Yuan, Qing-Chun Yu, Yi-Feng Liu, Liang-Liang Ma, Yi-Hua Wu

Journal of Electrochemistry

In this paper,cyclic voltammetry has been used to study the electrochemical performance of the treated and untreated graphite,soft graphite and PAN-carbon cloth in vanadium sulfate solution.The results show that: the reversibility of reaction can be improved on the surface of treated electrode,and the current can also increase;the electrochemical performance of treated electrode is remarkably enhanced;in the process of charge/discharge,the charge current can reach up to 20 mA/cm2,and discharge current up to 15 mA/cm2;surface morphology of the treated and untreated graphite show that the treatment can change the surface structure of electrode and also add the reaction …

Go to article

Study On The Microstructure Of Pb-Sn Alloy Obtained From Quasi-Two-Dimensional Electrodeposition, Bin Sun Aug 2006

Study On The Microstructure Of Pb-Sn Alloy Obtained From Quasi-Two-Dimensional Electrodeposition, Bin Sun

Journal of Electrochemistry

A two-layered structure of eutectic-solid sulotion is formed in the microstructure of Pb-Sn alloy obtained from quasi-two-dimensional electrodeposition.It is showed that this unique structure is caused by the variation of the current density on the growth interface.When the interface is located in the front of the whole deposits,the current density is high.So the Pb and Sn can deposit together and the eutectic texture forms.When the interface is in the rear of the whole deposits,the current density is low.At this moment the electrodeposition of Pb is the dominant reaction,and the Pb-based solid solution appears.

Go to article

Studies On Synthesis And Electrochemical Performance Of LiXNi1/3Mn1/3Co1/3O2 As Cathode Material For Lithium Ion Batteries, Xiao-Jian Guo, Jie Li, Yi-Xiao Li, Yong Yang Aug 2006

Studies On Synthesis And Electrochemical Performance Of LiXNi1/3Mn1/3Co1/3O2 As Cathode Material For Lithium Ion Batteries, Xiao-Jian Guo, Jie Li, Yi-Xiao Li, Yong Yang

Journal of Electrochemistry

A series of LiNi1/3Mn1/3Co1/3O2 were synthesized by a combined hydroxides coprecipitation and calcination method.Effects of synthesizing temperature of coprecipitations and the Li∶M ratios on structure and electrochemical performance of the materials were studied.The results showed that materials synthesized with coprecipitation at room temperature(~20 ~(o)C) delivered the best electrochemical performance.Another series of cathode materials LiXNi1/3Mn1/3Co1/3O2 with different Li∶M ratios were synthesized with this method.The results showed that sintering at high temperature could cause loss of LiOH,thus more LiOH should be added.It is demonstrated that Li …

Go to article

Voltammetric Behavior And Its Determination Of Acetaminophen At Poly (Congo Red) Modified Electrode, Hong-Bin Luo, Ya-Feng Zhang, Wei Chen, Xin-Hua Lin, Xiao-Yan Lin Aug 2006

Voltammetric Behavior And Its Determination Of Acetaminophen At Poly (Congo Red) Modified Electrode, Hong-Bin Luo, Ya-Feng Zhang, Wei Chen, Xin-Hua Lin, Xiao-Yan Lin

Journal of Electrochemistry

Cyclic voltammetry was used to prepare poly(Congo Red) film on glassy carbon electrode and to study the electrochemical behavior of acetaminophen on poly(congo red) modified electrode.Experimental resultal shows that the poly(congo red) modified electrode exhibits excellent electrocatalytic effect on the oxidation of acetaminophen.The peak currents of linear sweep voltammogram are linear to the acetaminophen concentrations over the range of 2.0×10-7～2.0×10-6 mol·L-1.The detection limit has been estimated to be 4.0×10-8 mol·L-1.This method can be used for the determination of acetaminophenin real sample.

Go to article

Electrochemical Behavior Of Electrolytic Manganese Dioxide In Mgso4 Solution, Dan-Mei Yu, Yu-Jun Si, Chang-Guo Chen, Yu-Ping Liu, Yan Liu Aug 2006

Electrochemical Behavior Of Electrolytic Manganese Dioxide In Mgso4 Solution, Dan-Mei Yu, Yu-Jun Si, Chang-Guo Chen, Yu-Ping Liu, Yan Liu

Journal of Electrochemistry

The rechargeability and crystal structure changing of electrolytic manganese dioxide(EMD) in MgSO4 electrolyte were investigated by cyclic voltammetry,galvanostatic charge/discharge and X-ray diffraction.The results have shown that the EMD has good rechargeability;after several initial cycles,the charge and discharge became stability;after discharge,the γ-MnO2 structure of EMD was changed,the production was reversible and could be recharged to γ-MnO2 structure again which ensured the rechargeability of EMD.

Go to article

Application Of Electrolessplating Technology In Interconnection Manufacturing Of Ultralarge-Scale Integration, Zeng-Lin Wang, Zhi-Juan Liu, Hong-Yan Jiang, Xiu-Wen Wang, Shingubara Shoso May 2006

Application Of Electrolessplating Technology In Interconnection Manufacturing Of Ultralarge-Scale Integration, Zeng-Lin Wang, Zhi-Juan Liu, Hong-Yan Jiang, Xiu-Wen Wang, Shingubara Shoso

Journal of Electrochemistry

In this paper,research progresses in electroless plating for damascene copper process were reviewed.Electroless nickel ternary alloy deposition for barrier layer and electroless copper plating for seed layer were presented.Bottom-up copper fill high-aspect-via-hole and electroless plating after ICB-Pd catalytic layer for seed layer were mainly introduced.The applications of electroless plating in ultralarge-scale integration were discussed,and the developing tendency was also suggested.

Go to article

Synthesis Of Zinc Polyhedral Microspheres And Applications In Alkaline Zn-Mno2 Battery, Hua Ma, Chun-Sheng Li, Fang-Yi Cheng, Chun-Yuan Zhou, Feng Gao, Jun Chen May 2006

Synthesis Of Zinc Polyhedral Microspheres And Applications In Alkaline Zn-Mno2 Battery, Hua Ma, Chun-Sheng Li, Fang-Yi Cheng, Chun-Yuan Zhou, Feng Gao, Jun Chen

Journal of Electrochemistry

The zinc polyhedral microspheres were synthesized by evaporation of pure zinc powders via a vapor-transport process.The results characterized by XRD and SEM show that the as-synthesized zinc powders are polyhedral microspheres with the diameter of 2~3 μm.The electrochemical investigation showed that the capacity of the as-assembled AA-size primary alkaline Zn-MnO2 battery was increased to 3.14 Ah under the constant discharge current of 100 mA by using the as-deposited microspherical zinc powders as the anode active materials and γ-MnO2 nanowires as the cathode active materials,indicating their potential application in high-energy batteries.

Go to article

High Density Lifepo4/C Synthesized By Controlled Crystallization And Microwave Carbon Thermal Reduction, Chang-Ping Tang, Jie-Rong Ying, Min Lei, Wei Li, Chang-Yin Jiang, Chun-Rong Wan May 2006

High Density Lifepo4/C Synthesized By Controlled Crystallization And Microwave Carbon Thermal Reduction, Chang-Ping Tang, Jie-Rong Ying, Min Lei, Wei Li, Chang-Yin Jiang, Chun-Rong Wan

Journal of Electrochemistry

The spherical FePO4·xH2O was prepared in the solution by controlled crystallization.The precursor FePO4 was obtained in high temperatureceramic approach,then the high density LiFePO4 /C was synthesized by microwave carbon thermal reduction.The structure and morphology of the materials were characterized by means of XRD and SEM techniques,and the electrochemical properties were studies by charge-discharge experiments.

Go to article

Effect Of Cracks On Corrosion Of Rebar In Concrete Studied By Wire Beam Electrode, Guo-Xi Li, Xian-Lu Hou, Ri-Long Zhu, Jin-Feng Hu, Yan-Na Du May 2006

Effect Of Cracks On Corrosion Of Rebar In Concrete Studied By Wire Beam Electrode, Guo-Xi Li, Xian-Lu Hou, Ri-Long Zhu, Jin-Feng Hu, Yan-Na Du

Journal of Electrochemistry

The effects of crack and ethanolamine on corrosion of rebar in concrete were studied by measuring the distribution of corrosion potential and polarization resistance of iron wires in 10% NaCl solution.The results showed that the diffusion of water,oxygen and chloric ion toward concrete was accelerated by the crack which intensified the nonuniform corrosion of iron wire with the regions near to crack as anode and the uncracked regions as cathode.Ethanolamine could diffuse into the body of concrete and absorb on the surface of iron wire,which reduced iron corrosion evidently and successfully inhibited the nonuniform corrosion caused by crack without changing …

Go to article

Corrosion Behavior Of The Welding Seam Of The Q235 Steel Jointed By J420 Electrode In Ammonium Sulfite Solution, A-Li Lei, Qiao-Qin Guo, La-Jun Feng May 2006

Corrosion Behavior Of The Welding Seam Of The Q235 Steel Jointed By J420 Electrode In Ammonium Sulfite Solution, A-Li Lei, Qiao-Qin Guo, La-Jun Feng

Journal of Electrochemistry

The corrosion behavior of welding seam of the Q235 steel jointed by J420 electrode in ammonium sulfite solution was researched.The results of electrochemical method of welding seam and metallurgical structure analysis showed that the poor corrosion resisting property was determined by its structure after the Q235 steel was jointed by J420 electrode.The sulfite corrosion rate was accelerated by increasing the temperature and concentration of ammorium.

Go to article

Effect Of Preparation Conditions On Electroluminescence Of Porous Silicon, Ya-Jun Yang, Qing-Shan Li, Xian-Yun Liu, Ning Zhang, Bo Zhao, Xue-Gang Zheng, Ming-Ji Shi, Da Chen, Jing-Jing Wang May 2006

Effect Of Preparation Conditions On Electroluminescence Of Porous Silicon, Ya-Jun Yang, Qing-Shan Li, Xian-Yun Liu, Ning Zhang, Bo Zhao, Xue-Gang Zheng, Ming-Ji Shi, Da Chen, Jing-Jing Wang

Journal of Electrochemistry

Electrically induced visible light emitting porous silicon devices with the structure of ITO/PS/p-Si/Al were fabricated by evaporation-anodic oxidation method.The light emission last for a few hours under 7.5V forward bias conditions.It was shown that the electroluminescence(EL) peaks shifted to the blue with the increasing of current density,erosion time and solution concentration.In order to achieve samples with low driven voltage,long light emission time and high EL efficiency,porous silicon should be prepared under low current density and short erosion time.

Go to article

Tyrosinase Immobilizarion On Boron-Doped Diamond Electrodes And The Determination Of Phenolic Compounds, Yan-Li Zhou, Jin-Fang Zhi May 2006

Tyrosinase Immobilizarion On Boron-Doped Diamond Electrodes And The Determination Of Phenolic Compounds, Yan-Li Zhou, Jin-Fang Zhi

Journal of Electrochemistry

As-grown BDD surfaces were first functionalized by photochemically linking vinyl groups of allylamine,producing covalently linked amine-terminated active BDD surfaces.Then the tyrosinase was immobilized onto the BDD surface through peptide linking.Cyclic voltammograms of phenol,pcresol and hydroquinone were measured using the tyrosinase-modified BDD electrode and amperometric characteristics such as sensitivity,linear response range and stability were studied.

Go to article

Electrochemical Studies On Electrocatalytic Activity Of AuCore PtShell Nanoparticles To Methanol Oxidation, Fang Bao, Jian-Lin Yao, Ren-Ao Gu May 2006

Electrochemical Studies On Electrocatalytic Activity Of AuCore PtShell Nanoparticles To Methanol Oxidation, Fang Bao, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

AucorePtshell nanoparticles with different thicknesses were prepared by using chemical reduction method,and characterized by ultraviolet-visible spectroscopy(UV-Vis),transmission electron microscopy(TEM) and cyclic voltammetry(CV).The electrocatalytic activity of AucorePtshell nanoparticles with the mean diameter of 70~80 nm to methanol oxidation was investigated by cyclic voltammetry in the acid solution.The results revealed that the prepared core-shell nanoparticles were covered by Pt shell and exhibited the similar optical property and electrocatalytic activity with the normal Pt surface.Moreover,the electrocatalytic activity increased with the electrochemical sweep in the certain potential range.It might be contributed by the special loose structure of Pt shell …

Go to article

Electrochemical Preparation Of Gd-Ni Alloy Film In Acetamide-Urea-Nabr Melt, Bi-Qing Chen, Jian-Chao Wang, Chen-Yu Guo, Jin-Gui Wang, Qing Liu May 2006

Electrochemical Preparation Of Gd-Ni Alloy Film In Acetamide-Urea-Nabr Melt, Bi-Qing Chen, Jian-Chao Wang, Chen-Yu Guo, Jin-Gui Wang, Qing Liu

Journal of Electrochemistry

Cyclic voltammetry was used to study the electroreduction of Ni2+ to Ni on Pt and Cu electrode in acetamide-urea-NaBr melt at 353K.It is irreversible in one step.At Pt and Cu eletrode the diffusion coefficient and electron transfer coefficient of Ni2+ in 0.063mol/dm3) NiCl2-acetamide-urea-NaBr melt were determined.The transfer coefficient α=0.28 and diffusion coefficient D_(0)=4.63×10-5 cm2·s-1 of the Pt eletrode and transfer coefficient α=0.22 and diffusion coefficient D_(0)=6.05×10-7 cm2·s-1 of the Cu eletrode were measured.It was put emphasis on that Gd3+ is not reduced to Gd alone …

Go to article

Study On Composite Organic Inhibitor Of Zinc Electrode In Alkaline Solutions, Xue-Tao Bu, Guang-Chuan Liang, Cui Li May 2006

Study On Composite Organic Inhibitor Of Zinc Electrode In Alkaline Solutions, Xue-Tao Bu, Guang-Chuan Liang, Cui Li

Journal of Electrochemistry

The synergetic influence of sodium dodecyl benzene sulfonate(SDBS) with Tween-20(Tween) on zinc electrode was studied by polarization experiment,surface tension test,discharge test and SEM.It is found that the composite inhibitor ST has a much higher efficiency.The addition of Tween reduced the critical micell concentration of SDBS on zinc electrode remarkably and the distribution of adsorption became more homogeneous.ST inhibits corrosion of zinc electrode and improves discharge capacity of the whole battery.Through electrochemical morphological observation of anodic passivation behaviors of zinc electrode,the absorption of ST on electrode surface makes discharged production much smaller and keeps crude porous structure intact.Passivation of zinc electrode …

Go to article

Electrochemical Impedance Spectrum Of Ferrocene At A Rotating Disk Glassy Carbon Electrode And Its Interaction With Dna, Can-Hui Chen, Hong Li, Jian-Zhang Zhou, Zhong-Hua Lin, Wei Zhu, Quan-Xin Zhang May 2006

Electrochemical Impedance Spectrum Of Ferrocene At A Rotating Disk Glassy Carbon Electrode And Its Interaction With Dna, Can-Hui Chen, Hong Li, Jian-Zhang Zhou, Zhong-Hua Lin, Wei Zhu, Quan-Xin Zhang

Journal of Electrochemistry

The electrochemical impedance spectrum(EIS) of ferrocene(Fc) at a rotating glassy carbon(GC) electrode and its interaction with calf thymus DNA in Tris-NaCl buffer solution(pH=7.2) have been investigated by using electrochemical techniques such as rotating disk electrode(RDE),EIS and its data fitting.A plateau of the limiting current for the voltammetric curve and two capacitance arches obtained at the rotating GC electrode are exhibited.The interaction of Fc with DNA is represented by the decrease of limiting diffusion current and the increase of electrochemical reaction resistances with the increase of DNA concentration,respectively.On the other hand,based on the theoretical analysis and data fitting of RDE and …

Go to article

Electrochemical Behavior And Reduction Mechanism Of High Valence Silver Oxide Ag3O4 In Alkaline Solution, Yan Cheng, Ming Yu, Man-Ming Yan, Zhi-Yu Jiang May 2006

Electrochemical Behavior And Reduction Mechanism Of High Valence Silver Oxide Ag3O4 In Alkaline Solution, Yan Cheng, Ming Yu, Man-Ming Yan, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical properties of high-valence silver oxide Ag3O4 in alkaline solution were investigated for the first time and the reduction mechanism of Ag3O4 was proposed. It can be recognized that Ag3O4 consists of Ag(Ⅲ) and Ag(Ⅱ)~(*). From the results of voltammetry and XRD experiments it was found that the reduction process of Ag3O4 was more complicated. It could be electrochemically reduced through the series reactions of Ag(Ⅲ) →Ag(Ⅱ) →Ag(Ⅰ) →Ag(O) at low discharge rate or Ag(Ⅲ) →Ag(Ⅰ) →Ag(O) at higher discharge rate.And the Ag(Ⅱ)~(*) could be reduced to …

Go to article

Electrochemical Studies Of Iron-Doped Nickel Oxide Electrode For Oxygen Evolution Reaction, Jin-Zhao Huang, Zheng Xu, Hai-Ling Li, Guo-Hu Kang, Wen-Jing Wang May 2006

Electrochemical Studies Of Iron-Doped Nickel Oxide Electrode For Oxygen Evolution Reaction, Jin-Zhao Huang, Zheng Xu, Hai-Ling Li, Guo-Hu Kang, Wen-Jing Wang

Journal of Electrochemistry

In this paper,the iron-doped nickel oxide thin film as anode catalyst was prepared by RF reactivesputtering method.The oxygen evolution reaction(OER) on the iron-doped nickel oxide was investigated withcyclic voltammetry,liner sweep voltammetry,polarization curves and electrochemical impedance spectroscopy.Results showthat the iron acts as active site in the film which makes the overpotential lower,and changes therate-limiting from primary discharge of OH-ions to the recombination of oxygen atom.With the increasing of ox-ygen content in flu ratio during sputtering,the electrocatalytic activities of the film increase.Iron-doped nickeloxide thin film is promising material as OER electrocatalyst for hydrogen production than the nickel electrode.The oxygen overpotential on the …

Go to article

Electrodeposition Of Three-Dimensional Porous Copper Films Using Hydrogen Bubbles As Template, Ya-Feng Sun, Zhen-Jiang Niu, Shu-Qiong Cen, Ze-Lin Li May 2006

Electrodeposition Of Three-Dimensional Porous Copper Films Using Hydrogen Bubbles As Template, Ya-Feng Sun, Zhen-Jiang Niu, Shu-Qiong Cen, Ze-Lin Li

Journal of Electrochemistry

Using cathodic hydrogen bubbles as a template,the three-dimensional(3-D) porous copper films have been successfully electrodeposited from a bath of 0.2 mol·dm-3 CuSO4 and 1.5 mol·dm-3 H2SO4,effects of deposition parameters including temperature,current density and additives(Na2SO4,HCl and Polyethylene glycol(PEG)) on the morphologies of the deposits have been systematically studied.SEM results showed that both the pore size and thickness of the pore walls decreased with cooling the electrolyte temperature or adding(Na2SO4) or PEG into the bath when the other deposition parameters were fixed.With addition small amounts of HCl …

Go to article

Structure And Properties Of Electrodeposited Sn-Co Alloy Electrodes As Anode Material For Lithium-Ion Secondary Batteries, Hong-Hong Jiang, Ling Huang, Shun-Wei Zhou, Fu-Sheng Ke, Fang-Zu Yang, Xiao-Yong Fan, Shi-Gang Sun May 2006

Structure And Properties Of Electrodeposited Sn-Co Alloy Electrodes As Anode Material For Lithium-Ion Secondary Batteries, Hong-Hong Jiang, Ling Huang, Shun-Wei Zhou, Fu-Sheng Ke, Fang-Zu Yang, Xiao-Yong Fan, Shi-Gang Sun

Journal of Electrochemistry

The Sn-Co alloy deposits were prepared by electroplating.The structure and electrochemical performance of the electroplated Sn-Co alloys have been investigated in detail. Experimental results show that the porous Sn-Co alloy film exhibits hexagonal solid solution,with Sn as the solvent, Co as the solute. The texture of the Sn-Co alloy coating exhibits(110) preferred orientation. Electrochemical tests show that the porous Sn-Co alloy coating electrodes can deliver a discharge capacity of 643mAh/g in the first cycle. At the 20h cycle the charge was 461mAh/g. At initial charge curve the irreversible capacity is probably associated to a combination of processes, which may …

Go to article

Preparation Of Spherical Ni(Oh)2 Coated With Coooh And Its Fast Charge Performance, Min-Jie Yang, Jun-Min Nan, Jian-Jun Xue, Yan Cui, Ming Cui May 2006

Preparation Of Spherical Ni(Oh)2 Coated With Coooh And Its Fast Charge Performance, Min-Jie Yang, Jun-Min Nan, Jian-Jun Xue, Yan Cui, Ming Cui

Journal of Electrochemistry

Spherical Ni(OH)2 was coated with CoOOH through chemical precipitation and electrolytic oxidation.The influences of CoOOH coating on fast charge performance ofMH/Ni battery were studied by preparing high capacity and fast charge AA size MH/Ni batteries.The sample coated with CoOOH was characterized by Infrared spectrum(IR) and scanning electron microscopy(SEM).The results showed that the internal resistance decreased 3.4 mΩ,the charge plateau lower and the cell temperrature was below 55 ℃ at the end of charging process when the cathode active material used Ni(OH)2 coated with CoOOH as compared with that doped by CoO.In addition,an initial discharge efficiency of 90.6% and …

Go to article

Conductivity Of Comb Polyether Pure Solid Polymer Electrolyte, Lin Ye, Peng Gao, Zeng-Guo Feng, Feng Wu, Shi Chen, Guo-Qing Wang Feb 2006

Conductivity Of Comb Polyether Pure Solid Polymer Electrolyte, Lin Ye, Peng Gao, Zeng-Guo Feng, Feng Wu, Shi Chen, Guo-Qing Wang

Journal of Electrochemistry

A comb polymer was synthesized through cationic ring-opening polymerization starting from a monomer 3-hydroxymethyl-3-methyl-oxetane.The ion conductivity was measured by CHI660A electrochemical station under various lithium salt concentrations and various temperatures.The highest ion conductivity was recorded to be 10-4.43 S/cm at room temperature and 10-3.44 S/cm at 80 ℃.DSC results showed that the segment moves more difficultly with the increasing of lithium salts concentration.XPS found the existence of aggregating lithium ions in POE5 and POE10,and it suggested that POE20 had a suitable lithium concentration for polymer electrolyte.

Go to article

Studies On Pva-Cmc-Koh-H2O Alkaline Polymer Electrolytes, An-Bao Yuan, Jun Zhao Feb 2006

Studies On Pva-Cmc-Koh-H2O Alkaline Polymer Electrolytes, An-Bao Yuan, Jun Zhao

Journal of Electrochemistry

A given amount of sodium carboxymethyl cellulose(CMC)was added to PVA complex and thus the PVA-CMC-KOH-H2O alkaline polymer electrolyte with this modification was prepared.The properties of the polymer electrolyte films were characterized by AC impedance,cyclic voltammetry,differential thermal analysis and infrared spectroscopic analysis methods.The polymer electrolyte exhibited a high ionic conductivity,typically 10-2S·cm-1 with an electrochemical stability window of about 1.6 V on stainless steel blocking electrodes.The influence of the film composition such as KOH,H2O and CMC on ion conductivity was investigated.In addition,a preliminary study was carried out on the polymer electrolyte for Ni/MH battery.It was …

Go to article

Anodic Behaviors Of Pb-Ca-Sn-Re Alloy And Tradditional Pb-Ca-Sn Alloy In Sulfuric Acid Solutions, Dang-Guo Li, Gen-Shu Zhou, Liang Yao, Guan-Fa Lin, Mao-Sheng Zheng Feb 2006

Anodic Behaviors Of Pb-Ca-Sn-Re Alloy And Tradditional Pb-Ca-Sn Alloy In Sulfuric Acid Solutions, Dang-Guo Li, Gen-Shu Zhou, Liang Yao, Guan-Fa Lin, Mao-Sheng Zheng

Journal of Electrochemistry

The anodic behaviors of Pb-Ca-Sn-Re and Pb-Ca-Sn alloys were investigated at 1.28 V(vsHg/(H2SO4)) in 4.5 mol/L sulfuric acid solution by means of ac voltammetry,ac impedance and cyclic voltammetry.The results showed that the corrosion-resistance property of Pb-Ca-Sn-Re alloy is better than that of tradditional Pb-Ca-Sn alloy,the growth of Pb(Ⅱ) compounds was inhibited in the film of Pb-Ca-Sn-Re alloy,and the film impedance of Pb-Ca-Sn-Re alloy was decreased,indicating that the conductivity of the film was(increased),which is helpful to enhance the deep recycling property for lead acid battery.

Go to article

Mechanism Of Self Discharge Performance Improvement In The Ni-Mh Batteries With Naoh Electrolyte, Xiao-Feng Li, Tong-Chi Xia, Hui-Chao Dong, Yan-Wei Wei Feb 2006

Mechanism Of Self Discharge Performance Improvement In The Ni-Mh Batteries With Naoh Electrolyte, Xiao-Feng Li, Tong-Chi Xia, Hui-Chao Dong, Yan-Wei Wei

Journal of Electrochemistry

The self-discharge performance and charge efficiency at 60 ℃ for Ni-MH battery can be markedly enhanced by using NaOH electrolyte instead of KOH electrolyte.Both the results of electrochemical impedance spectroscopy and cyclic voltammetry tests indicate that the separation of H2 from the negative electrode may be partly blocked in the former because of the change of the adsorption/desorption behavior of H on the surface of the negative electrode,thus results in an improvement of self-discharge performance of the battery.

Go to article

2006 National Conference On Corrosion Electrochemistry And Measuring Methods, Editorial Office Of J.Electrochem. Feb 2006

2006 National Conference On Corrosion Electrochemistry And Measuring Methods, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Go to article

Electrocatalytic Oxidation Of Glucose On Nano Pt/C Electrode, Cui-Lian Chen, Xiao-Lan Wei, Pei Kang Shen Feb 2006

Electrocatalytic Oxidation Of Glucose On Nano Pt/C Electrode, Cui-Lian Chen, Xiao-Lan Wei, Pei Kang Shen

Journal of Electrochemistry

Nano Pt/C electrocatalysts were prepared by intermittent microwave heating method.The electrooxidation of glucose on smooth Pt and～Pt/C electrodes has been studied and compared.The results showed that the electrochemical properties on nano Pt/C were improved due to the reduction of the overpotential and the increase in the kinetic rate.The surface area would be significantly increased when the particle size of the catalyst was reduced to nano-scale,resulting in the increase in the activity.The enhancement in the resistance to poisoning could be explained that the oxygen-containing species are easier to react with poisoning species on nano Pt/C and re-active the electrode.

Go to article

First Prev Next Last