Materials Science and Engineering Commons^™

Preparation Of Pdcoir Tetrahedron Nanocatalysts And Its Performance Toward Ethanol Oxidation Reaction, Zhi-Yuan Yu, Rui Huang, Jie Liu, Guang Li, Qian-Tong Song, Shi-Gang Sun

Journal of Electrochemistry

As a new energy conversion device, direct ethanol fuel cells (DEFCs) are widely concerned because of their remarkable advantages such as high theoretical energy density and wide fuel sources. However, the rapid development of DEFCs has been severely impeded due to the sluggish kinetic process and toxic intermediates especially in their anodic reactions. Palladium (Pd)-based materials are considered to be excellent anode catalysts for DEFCs, especially under alkaline conditions. And further improving their performance is an important direction to promote the development of DEFCs. Surface structure and composition are the key factors affecting the performance of catalysts which can be …

Preparation And Performance Investigation Of Li-Sgo Doped Semi-Ipns Porous Single Ion Conducting Polymer Electrolyte, Yun-Feng Zhang, Jia-Ming Dong, Chang Tan, Shi-Kang Huo, Jia-Ying Wang, Yang He, Ya-Ying Wang

Journal of Electrochemistry

Herein, the lithiated sulfonated graphene oxide (Li-SGO) was successfully prepared via three steps by sulfonation of graphene oxide with 3-merraptnpropylt rimethnxysilane, oxidation of thiol into sulfonate with hydrogen peroxide and lithiation of sulfonate with aqueous lithium hydroxide. The as-prepared Li-SGO was then introduced into the semi-interpenetrating networks of single ion conducting polymer electrolyte (Li-SGO-FPAS) and poly vinylidenefluoride-hexafluoro propylene (PVDF-HFP) binder by in-situ polymerization to fabricate the porous single ion conducting polymer electrolyte membrane (Li-SGO-po-FPAS) generated from the poor compatibility between aromatic Li-SGO-FPAS and aliphatic PVDF-HFP binder. The key properties such as morphology, porosity, solvent uptake, mechanical …

Syntheses Of Na3V2(Po4)2O2F As A Cathode For Sodium Ion Battery Application, Kai Wu

Journal of Electrochemistry

High-temperature solid-state method, hydro-thermal method and solvo-thermal method have been mainly employed to synthesize Na₃V₂(PO₄)₂O₂F (NVPF) cathode materials. However, these methods are energy consuming and complicated, which is not applicable for a large scale industrial production. In this study, a rather low-temperature (70℃) co-precipitation strategy was proposed to synthesize NVPF cathode materials. The as-prepared NVPF cathode materials showed a spherical shape with a diameter of 400 ~ 500 nm, and exhibited a sodium storage of 105.6 mAh·g^-1 and an efficiency of 90.06%. After a simple thermal process, the specific …

Molecular To Macroscopic Understanding Of Chloroaluminate Anion Intercalation In Rechargeable Aluminum-Graphite Batteries, Jeffrey Xu

Dissertations and Theses

Today’s global energy challenges pose an urgent need to electrify transportation and better store intermittent renewable energy sources (e.g., solar and wind energy). For such large-scale battery applications, aluminum batteries are a promising “beyond lithium-ion” technology due to the high volumetric capacity, earth abundance, low-cost, and inherent safety of aluminum metal. However, there are very few compatible positive electrode materials that exhibit high energy density and cycling stability, in part due to the challenges of electrochemically intercalating highly charged Al³⁺ cations. Recently, graphite has been demonstrated as a promising positive electrode material in non-aqueous rechargeable aluminum batteries, which store …

Investigation Of Cation Exchange Behaviors Of FaXMa1-XPbl3 Films Using Dynamic Spin Coating, Hyang Mi Yu, Byeong Geun Jeong, Dae Young Park, Seong Chu Lim, Gon Namkoong, Mun Seok Jeong

Applied Research Center Publications

In this study, we fabricated and characterized uniform multi-cation perovskite FA_xMA_1−xPbI₃ films. We used the dynamic spin-coating method to control the cation ratio of the film by gradually increasing the FA+, which replaced the MA+ in the films. When the FA+ concentration was lower than xFA ~0.415 in the films, the stability of the multi-cation perovskite improved. Above this concentration, the film exhibited δ-phase FAPbI₃ in the FA_xMA_1−xPbI₃ films. The formation of δ-phase FAPbI₃ disturbed the homogeneity of the photoluminescence spatial distribution and suppressed the absorption spectral bandwidth …

Theoretical Analysis Of Experimental Data Of Sodium Diffusion In Oxidized Molybdenum Thin Films, Orlando Ayala, Benjamin Belfore, Tasnuva Ashrafee, John Akwari, Grace Rajan, Shankar Karki, Deewakar Poudel, Sylvain Marsillac

Engineering Technology Faculty Publications

In this work, the diffusion process of sodium (Na) in molybdenum (Mo) thin films while it was deposited on soda lime glass (SLG) was studied. A small amount of oxygen was present in the chamber while the direct-current (DC) magnetron sputtering was used for the deposition. The substrate temperatures were varied to observe its effect. Such molybdenum films, with or without oxidations, are often used in thin film solar cells, either as back contact or as hole transport layers. Secondary ion mass spectrometry (SIMS) was used to quantify the concentration of the species. A grain diffusion mechanistic model incorporating the …

Core-Shell Structured Ru@Ptru Nanoflower Electrocatalysts Toward Alkaline Hydrogen Evolution Reaction, Xue-Liang Wang, Yuan-Yuan Cong, Chen-Xi Qiu, Sheng-Jie Wang, Jia-Qi Qin, Yu-Jiang Song

Journal of Electrochemistry

Water electrolysis for hydrogen production is beneficial for solving the problem of energy crisis and environmental issues. It is necessary to study highly active and cost-effective catalysts toward hydrogen evolution reaction (HER) to reduce the consumption of noble metals. Herein, we report the synthesis of core-shell structured Ru@Pt_0.24Ru nanoflowers electrocatalyst by stepwise reduction of Ru and Pt precursors in the mixture of oleylamine and benzyl alcohol at 160 ^oC. The average diameter of the resultant Ru@Pt_0.24Ru was 16.5±4.0 nm with a bulk atomic ratio between Pt and Ru of 0.24:1 and a surface ratio of …

Preparations And Photoelectrochemical Performances Of Rgo-Tio2 Nanotubes Arrays, Ze-Yang Zhang, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Decorating TiO₂ nanotube arrays with RGO to improve the photocatalytic activity of TiO₂ nanotube arrays has been reported. For the reported RGO-TiO₂ nanotube arrays, TiO₂ nanotube arrays were prepared by anodizing the high-purity Ti foil in an organic electrolyte for multiple-step treatments, while RGO were deposited on TiO₂ nanotube arrays by using cyclic voltammetry or other electrical reduction methods. To enhance the reduction degree and the coverage of RGO on the resultant RGO-TiO₂ nanotube arrays, in this work, the one-step electrochemical anodization in hydrofluoric acid was used to fabricate TiO₂ nanotube arrays with …

Effect Of Reaction Conditions On Cu⁃Catalyzed Co2 Electroreduction, Chang Zhu, Wei Chen, Yan-Fang Song, Xiao Dong, Gui-Hua Li, Wei Wei, Yu-Han Sun

Journal of Electrochemistry

Electrochemical conversion of carbon dioxide (CO₂) driven by renewable electricity that can meet both carbon emission reduction and renewable energy utilization has been rapidly developed in recent years. Copper (Cu) catalyst has long been a promising candidate for CO₂ electroreduction applications because of its natural abundance and specific capability of producing a substantial amount of C2 products. However, various metallic Cu electrodes reported have been significantly influenced by the adsorption of certain cation/anion ions, resulting in wide-span catalytic activities and selectivity for various products. In addition, a recent report demonstrated that by virtue of gas-diffusion flow cell …

Preparation And Process Optimization Of Cathode Materials For Lithium-Sulfur Batteries, Kai Wu

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries represent promising candidates for next-generation energy storage system due to their high energy density and low material cost. However, the industrial application of Li-S batteries remains challenges because of the shuttle effect from lithium polysulfides and the lack of facial routes for Li-S battery preparation. To solve these problems, a cathode consisting of different commercial carbon materials, namely, acetylene black (SP), Ketjen Black (KB) and carbon nanotube (CNT), with sulfur (S) is prepared separately for Li-S battery. After the process of 8-h ball milling for KB/S composite, together with the polyvinyl pyrrolidone (PVP) binder, the cathode could …

Numerical Simulations Of Current And Temperature Distribution Of Symmetrical Double-Cathode Solid Oxide Fuel Cell Stacks Based On The Theory Of Electric-Chemical-Thermal Coupling, Cheng-Rong Yu, Jian-Guo Zhu, Cong-Ying Jiang, Yu-Chen Gu, Ye-Xin Zhou, Zhuo-Bin Li, Rong-Min Wu, Zheng Zhong, Wan-Bing Guan

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) is a high-efficient clean conversion device for future energy management. Because of the low antioxidant reduction ability and complex thermal stress, the structure of traditional asymmetrical thin anode-supported planar SOFC is easily to be broken under stack operating conditions. To overcome these defects, a new complete symmetrical SOFC based on double-sided cathodes was developed. To study the influences of gas flow direction and current collection mode on the cell performance inside stack, a numerical model was established by finite element method based on the theory of electro-thermo-chemo multiphysical coupling. By applying this model, the molar …

Step-By-Step Modification Of Graphite Felt Electrode For Vanadium Redox Flow Battery, Jing-Yuan Lou, Dong-Jiang You, Xue-Jing Li

Journal of Electrochemistry

As a well-known electrode material of the vanadium redox flow battery (VRFB),graphite felt electrode is the frequently-used electrode material in VRFB, and its low electrochemical activity is one of the key factors for the low power density of VRFB. In this work, we proposed a step-by-step modification method, which used KMnO₄ to oxidize graphite felt first and then placed in an activation solution to excite its reactivity, to improve the electrochemical performance of the graphite felt electrode. According to the results from cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) characterizations …

Degradation And Thermal Characteristics Of Lini0.8Co0.15Al0.05O2/Graphite Lithium Ion Battery After Different State Of Charge Ranges Cycling, Cun Wang, Wei-Jiang Zhang, Teng-Fei He, Bo Lei, You-Jie Shi, Yao-Dong Zheng, Wei-Lin Luo, Fang-Ming Jiang

Journal of Electrochemistry

The LiNi_0.8Co_0.15Al_0.05O₂ (NCA) cathode exhibits high energy density and large reversible capacity, which plays an essential role in the field of electric vehicles (EVs). However, low capacity retention and poor thermal stability limit its application. Few literatures are found for the capacity degradation mechanism of NCA/graphite batteries at home and abroad. The different state of charge (SOC) ranges cycle degradation behaviors of 18650-type NCA/graphite (2.4 Ah) battery were studied in this paper. The SOC ranges considered were 0% ~ 20% (low), 20% ~ 70% (medium), 70% ~ 100% (high), and 0% ~ 100% …

Preparations And Sodium Storage Properties Of Ni3S2@Cnt Composite, Ming-Tao Duan, Yan-Shuang Meng, Hong-Shuai Zhang

Journal of Electrochemistry

Transition metal sulfides (TMSs)-based electrode materials with highly reversible sodium storage have attracted extensive attentions as one of the most prospective electrode materials for sodium ion batteries (SIBs). However, low cycling stability and rate property caused by large volume expansion and poor electronic conductivity during the electrochemical reaction still hamper their further practical application. In this work, in-situ encapsulated Ni₃S₂ nanoparticles in carbon nanotubes (Ni₃S₂@CNT) have been successfully fabricated as an anode material for high-performance SIBs by a one-step solid-phase calcination process. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), …

Effect Of Stereotaxically-Constructed Graphene On The Negative Electrode Performance Of Lead-Acid Batteries, Pin-Song Chen, Yi-Tao Hu, Xin-Yi Zhang, Pei-Kang Shen

Journal of Electrochemistry

With the advantages of high ratio surface area, excellent conductivity and high stability, the stereotaxically-constructed graphene (SCG) material was added to the negative active material (NAM) of lead-acid battery for improving battery performance. XRD, SEM and cyclic voltammetry tests were carried out to analyze the influence of SCG on negative active material. It is found that the conversion efficiency of lead sulfate to lead in the negative active material added with SCG material was higher than that of control group, and the particle size of the lead sulfate obtained after the discharge reaction was smaller, which are favorable factors for …

Growth And Characterization Of Semiconductor Materials And Devices For Extreme Environments Applications, Abbas Sabbar

Graduate Theses and Dissertations

Numerous industries require electronics to operate reliably in harsh environments, such as extreme high temperatures (HTs), low temperature (LT), radiation rich environments, multi-extreme, etc. This dissertation is focused on two harsh environments: HT and multi-extreme.

The first study is on HT optoelectronics for future high-density power module applications. In the power modules design, galvanic isolation is required to pass through the gate control signal, reject the transient noise, and break the ground loops. The optocoupler, which consists of a lighting emitting diode (LED) and photodetector (PD), is commonly used as the solution of galvanic isolation at room temperatures. There is …

High-Temperature Optoelectronic Device Characterization And Integration Towards Optical Isolation For High-Density Power Modules, Syam Madhusoodhanan

Graduate Theses and Dissertations

Power modules based on wide bandgap (WBG) materials enhance reliability and considerably reduce cooling requirements that lead to a significant reduction in total system cost and weight. Although these innovative properties lead power modules to higher power density, some concerns still need to be addressed to take full advantage of WBG-based modules. For example, the use of bulky transformers as a galvanic isolation system to float the high voltage gate driver limits further size reduction of the high-temperature power modules. Bulky transformers can be replaced by integrating high-temperature optocouplers to scale down power modules further and achieve disrupting performance in …

A Model For The Anodic Carbonization Of Alkaline Polymer Electrolyte Fuel Cells, Qi-Hao Li, Ying-Ming Wang, Hua-Long Ma, Li Xiao, Gong-Wei Wang, Jun-Tao Lu, Lin Zhuang

Journal of Electrochemistry

The alkaline polymer electrolyte fuel cell (APEFC) has made appreciable progress in recent years but is still suffering performance loss during discharge with air as the oxidant. Several theories have been suggested to interpret the loss. However, efforts are still needed to reach a clear quantitative understanding. Based on the major experimental findings in combination with thermodynamics and kinetics of the reactions involved in the anode, this paper presents a model featuring layered carbonization in the anode and relevant grouped equations. The simulation results generated from the latter are compared with experiments, and possible principles to suppress the performance loss …

Porous-Electrode Theory Of Lithium Ion Battery: Old Paradigm And New Challenge, Xiao-Xiao Wang, Zi-Rui Zhou, Qiang Shan, Zeng-Ming Zhang, Jun Huang, Yu-Wen Liu, Sheng-Li Chen

Journal of Electrochemistry

A critical review on the porous electrode theory developed by Newman and his colleagues is presented. We propose several ideas for further development of this theory by analyzing its limitations. The classical Newman theory does not consider ion steric effect in describing ion transport in electrolyte solutions, which can be amended by a newly developed ion-vacancy coupled charge transfer model for ion transport in concentrated solutions. Ion transport in solid particles of active materials is essentially an ion-electron coupled transport process, and its rationality is verified by comparing the calculated and experimental diffusion coefficients of Li ⁺ ion in intercalation …

Facile Synthesis Of Nitrogen-Doped Graphene-Like Active Carbon Materials For High Performance Lithium-Sulfur Battery, Quan-Hua Meng, Wen-Wen Deng, Chang-Ming Li

Journal of Electrochemistry

Lithium-sulphur (Li-S) battery is regarded as a promising energy storage device because of its high theoretical capacity. However, the low S utilization and short cycling life limit the commercial applications. In this work, nitrogen-doped graphene-like carbon (NGC) materials were synthesized by simply pyrolyzing and carbonizing the mixture of melamine (C₃H₆N₆) and L-cysteine (C₃H₇NO₂S). The graphene-like structure in NGC effectively buffered the volume change of S during the discharge/charge process and improved the cycling stability. Meanwhile, nitrogen-containing functional groups in NGC facilitated the transportation of ions and suppressed the …

Progress And Prospects On Multifunctional Coating Separators For Lithium-Sulfur Battery, Zhuang-Zhuang Wei, Nan-Xiang Zhang, Feng Wu, Ren-Jie Chen

Journal of Electrochemistry

The development of advanced energy storage systems is crucial to meet the growing demand for electric vehicles, portable devices and renewable energy storage. Lithium-sulfur (Li-S) batteries, with their advantages of high specific energy, low cost of raw materials and environmental friendliness, are hotspots in the research field of new high performance batteries. However, there are still many problems which hinder the practical applications of lithium-sulfur batteries, such as the shuttle effect of soluble polysulfide intermediates, the growth of lithium dendrites, and the thermal stability and safety of lithium-sulfur batteries during use. The design of multifunctional coating separator is one of …

Electrochemical Engineering Of Carbon Nanodots, Lei Bao, Dai-Wen Pang

Journal of Electrochemistry

Aqueous batteries have been considered to be a competitive candidate for large-scale energy storage. However, most of aqueous batteries adopt inorganic electrode materials with metallic elements, which are based on the reversible insertion of metal ions, making their application being highly hindered by limited cycle life, environmental issue, high cost and low reserves. On the other hand, organic electrode materials offer the advantages of abundant reserves, tunable structures, renewability and environmental benignity. Furthermore, the wide internal space enables these organics to flexibly store various charge carriers. Organics have been investigated as the alternative to inorganic electrode materials. Herein, we review …

Licoo2 As Sulfur Host To Enhance Cathode Volumetric Capacity For Lithium-Sulfur Battery, Lu Wang, Xue-Ping Gao

Journal of Electrochemistry

Lithium-sulfur battery is one of the most promising secondary battery systems due to its super high theoretical gravimetric and volumetric energy densities (2600 Wh·kg^-1 and 2800 Wh·L^-1, respectively). However, the practical volumetric capacity of sulfur cathode is still unsatisfied due to the overuse of low-density host materials, such as carbon nanomaterials. Herein, commercial LiCoO₂ with the high tap density of 2.94 g·cm^-3 was used as the host material to build high density sulfur-based composite and compact electrode for increasing the volumetric capacity. Obviously, the tap density of the as-prepared S/LiCoO₂ composite was 1.90 g·cm …

Research Progress Of Key Components In Lithium-Sulfur Batteries, Jia-Jia Chen, Quan-Feng Dong

Journal of Electrochemistry

Due to the much higher theoretical specific capacity and energy density than the ones of traditional lithium ion battery, Li-S batteries have long been at the pinnacle in the realms of high-energy Li-metal batteries. However, the complicated electrochemical reactions on the sulfur cathode and Li anode, induced by the thermodynamic and kinetic behaviors of lithium polysulfides, are the intrinsic bottleneck to realize the full potential of Li-S batteries for practical application. In this review, we firstly discuss the roles, and thermodynamic and kinetic behaviors of polysulfides in the charging and discharging processes of Li-S batteries. Then, the functional design and …

Research Progress Of Sulfur Cathode Catalytic Conversions For Lithium-Sulfur Batteries, Qin-Jun Shao, Jian Chen

Journal of Electrochemistry

The electrochemical reduction of sulfur (S) takes place through multistep reactions when S is used as a cathode material. The complete discharge of S to form final product lithium sulfide (Li₂S) is a two-electron reaction. The formation of low-order lithium polysulfides (LiPS) needs to overcome certain energy barriers. And the reduction of Li₂S₂ to Li₂S is the rate-limited step. The reaction kinetic of sulfur cathode is the critical key to determine the electrochemical performance of Li-S batteries, such as specific energy, specific power and low temperature performance, etc. Accelerating the rate-limited step kinetics …

Recent Progress In Bifunctional Catalysts For Zinc-Air Batteries, Neng-Neng Xu, Jin-Li Qiao

Journal of Electrochemistry

Zinc-air battery has attracted great attention from researchers due to its high energy density and power density, which is expected to be widely used in energy conversion and storage. Air electrode as the core area of oxygen catalytic reaction is the focus of the entire zinc-air battery research. Recently, many research achievements have been made in non-noble metal bifunctional catalysts/electrodes with high activity, low cost and abundant species. In this review, we mainly focus on the reaction mechanism and the recent progress in non-noble metal oxide catalyst, carbon-based catalyst, and carbon-based transition metal compound composite and self-supporting electrode. In addition, …

Recent Progress On Enhancing Effect Of Nanosized Metals For Electrochemical Co2 Reduction, Yu-Ning Zhang, Dong-Fang Niu, Shuo-Zhen Hu, Xin-Sheng Zhang

Journal of Electrochemistry

The electrochemical conversion of CO₂ to chemical raw material for further utilization shows promising future to alleviate global warming and realize carbon cycle in nature, which is of great significance to the green chemistry and sustainable development. This review briefly introduces the advantages of CO₂ electrochemical reduction (CO₂ER) and its basic reaction principles, and summarizes the recent progress in a series of activity enhancement strategies based on nanosized metal catalysts. The influences of alloy effect, interface engineering, synergistic effect, surface defect engineering and support effect on the catalytic performance of nanosized metals for CO₂ER …

Research Progress Of Metal-Nitrogen-Carbon Catalysts Toward Oxygen Reduction Reaction Inm Changchun Institute Of Applied Chemistry, Ming-Jun Xu, Jie Liu, Jun-Jie Ge, Chang-Peng Liu, Wei Xing

Journal of Electrochemistry

The development of highly active and stable catalysts toward oxygen reduction reaction (ORR) has been facing severe challenges. In recent years, pyrolytic M-N-C catalysts and metal-organic framework derived materials made the performance of non-noble metal catalysts greatly improved, however, the molecular and atomic level understanding in the reaction active sites and the mechanism are still lacking. Here, we summarize the recent research progress made in the Changchun Institute of Applied Chemistry. We present a microporous metal-organic-framework confined strategy toward the preferable formation of ORR catalysts. Firstly, we studied the active site and proposed a new active site structure for the …

Electrochemical Carbon Dioxide Reduction In Flow Cells, Jia Fan, Na Han, Yan-Guang Li

Journal of Electrochemistry

Electrochemical carbon dioxide reduction (CO₂RR) is an appealing approach to convert atmospheric CO₂ to value-added fuels and industrial chemicals, and may play an important role during the transition to a carbon-neutral economy. In order to make this technology commercially viable, it is essential to pursue CO₂RR in flow reactors instead of conventional H-type reactors, and to combine electrocatalyst development with system engineering. In this review, we overview the cell configurations and performance advantages of the two types of flow reactors, analyze their shortcomings, and discuss the effects of their different components including gas diffusion electrode …

Electrolyte Tailoring For Electrocatalytic Reduction Of Stable Molecules, Jin-Han Li, Fang-Yi Cheng

Journal of Electrochemistry

Reduction of stable molecules such as CO₂ and N₂ is important process in electrochemical energy conversion and storage technologies for electrofuels production. However, for the inert nature of CO₂/N₂ molecule and competitive proton reduction in conventional aqueous electrolytes, selective electrochemical carbon/nitrogen fixation suffers from high overpotential, low reaction rate and low selectivity. While addressing these issues has witnessed substantial advances in electrocatalysts, much less attention has been placed on the electrolytes, which play an important role in regulating the local environment and thus the performance of catalysts under operating conditions. Rational design of electrolytes has …