Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Power and Energy

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 1081 - 1110 of 1352

Full-Text Articles in Materials Science and Engineering

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu Feb 2005

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu

Journal of Electrochemistry

Electrochemical oxidation is an effective technology for the phenol wastewater treatment, and the anode properties are important to the electrochemical oxidationefficiency. The over-potentials of oxygen evolution have been measured for thestainless steel, feasible graphite and SnO2/Ti anode respectively. Moreover, the synthetic phenol wastewater was treated by the electrochemical oxidation with the stainless steel or feasible graphite anodes. The experimental results showed that the order of the over-potential is SnO2/Ti > graphite > stainless steel; meanwhile, the COD values of purified water were approaching to or less than 100 mg·L-1, and the phenol concentrations in the purified …

Go to article

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang Nov 2004

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang

Journal of Electrochemistry

The electrochemical behaviours of DDAB-Hb-PME were studied in this paper. The (apparent) surface concentration of Hb was enhanced greatly by using the powder microelectrode (technique). NO reacts with Hb and absorbs on the surface of the modified carbon powder. Therefore, the output of the electrode was enhanced greatly by employing PME with higher reaction surface (area). The sensitivity of DDAB-Hb-PME is 3.1 mA/μmol·L-1·cm2, which is much larger than the values obtained with the traditional electrodes. The detection limit is 9 nmol·L-1 and the linear response range is 9～100 nmol·L-1.

Go to article

Improvement And Its Mechanism Of Storage Performance Of Ni-Mh Battery, Xiao-Feng Li, Li-Ping Ma, Yu-Wan Lou, Feng Li, Bao-Jia Xia Nov 2004

Improvement And Its Mechanism Of Storage Performance Of Ni-Mh Battery, Xiao-Feng Li, Li-Ping Ma, Yu-Wan Lou, Feng Li, Bao-Jia Xia

Journal of Electrochemistry

The storage performance of nickel-metal-hydride (Ni-MH) battery was studied by using galvanostatic charge-discharge and cyclic voltammetry. The experimental results indicated that CoOOH could not be completely restored after its being thoroughly reduced at lower potential, which might weaken electric conduction network in the positive electrode and result in fading of electrochemical properties of Ni-MH battery. Addition of nickel powder as a conductive agent into the positive electrode was beneficial to the capacity recovery after storage.

Go to article

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang Nov 2004

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang

Journal of Electrochemistry

Photo-catalytic titanium dioxide film in nano crystalline has been prepared by electrochemical oxidation process and adding different amount of ferric ion into the electrolyte during the anodic oxidation.The effects of Fe3+ dopen on absorption spectra and photo-catalytic of the titanium dioxide films have been studied. It shows that the Fe3+ dopen caused the red shife of the absorption edge for the incoming light and exhibited the improved photocatalytic reactivity.

Go to article

LicoXNi1-XO2 Cathode Materials Prepared By Electrolysis Of Co And Ni, Jin-Ping Wei, Xin Sun, Xiao-Yu Wang, Xi-Kui Bian, Jin-Ling Zhai, Yan-Jie Yan-Jie Nov 2004

LicoXNi1-XO2 Cathode Materials Prepared By Electrolysis Of Co And Ni, Jin-Ping Wei, Xin Sun, Xiao-Yu Wang, Xi-Kui Bian, Jin-Ling Zhai, Yan-Jie Yan-Jie

Journal of Electrochemistry

A new electrolytic method was developed to prepare LiCoxNi1-xO2 as a cathode material of lithium-ion battery. Contrary to the traditional method, electrolytic method is a potential method with simple process to industrialization and no pollution. Metal cobalt and nickel were electrolysed in parallel to prepare the precursor of CoxNi1- x(OH)2.Different compositional precursors could be conveniently prepared by changing electrolytic current. The LiCo0.3Ni0.7O2 cathode prepared by this method was found favorable charge-discharge and cycle properties. For the LiCo0.3Ni0.7O2 cathode material, …

Go to article

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen Nov 2004

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

Three new nano thin films of α-Fe2O3, TiO2 and α-Fe2O3-TiO2 by doping their powder with sodium alginate polymer were prepared. Surface structure and catalytic activities of the films were characterized by FTIR, XRD, PL, TEM and I-V techniques. The results of UV-visible absorption showed that the methylene blue was mineralized in aqueous of α-Fe2O3/SA, TiO2/SA and (α-(Fe2O3))-TiO2 /SA upon radiation with ultra violet light. α-Fe2O3 enhanced their photo-decolorized-activities by doping 15% TiO2.

Go to article

Applications Of New Activated Carbon Meterials In The Electric Double-Layer Capacitor, Jian-Jun Zhang, Hua Jiang, Jian-Hui Fang, Li-Yi Shi, Ren-He Yin, Yi Wen, Ji-Quan Liu Nov 2004

Applications Of New Activated Carbon Meterials In The Electric Double-Layer Capacitor, Jian-Jun Zhang, Hua Jiang, Jian-Hui Fang, Li-Yi Shi, Ren-He Yin, Yi Wen, Ji-Quan Liu

Journal of Electrochemistry

A new type activated carbon whose precursor was coconut shell could be obtained using specific physics-chemistry activation, and the activated carbon was applied as the material of electrode in EDLC (electrical double-layer capacitor),which had a large specific capacitance, and could charge and discharged in some large currents. Carbon dioxide and acid were used to modify carbon,and the effects of post-treatment on surface area and pore volume were investigated. A moulding method which has influence on some properties of carbon electrode with PTFE additive was researched in the paper.

Go to article

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma Nov 2004

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma

Journal of Electrochemistry

The air electrodes with different mass ratio of Pt/active carbon or carbon nanotube as catalyst layer material have been prepared. The electrocatalytic performances for oxygen reduction were evaluated by means of polarization curve and electrochemical impedance spectroscopy (EIS). The results disclosed that carbon nanotubes dealt with nitric acid in the catalyst layer had been improved obviously on the electrocatalytic activity. After the surface of carbon nanotube was oxygenated and aggraded with platinum, the catalyst had obviously effects on the electrocatalytic activity. The air electrode with the mass ratio of active carbon to Pt/carbon nanotube in 4∶1 showed better electrocatalytic activity, …

Go to article

The Investigation Of Bafesi/C Alloy Composite As Anode Materials For Li-Ion Battery, Rui-Xiang Feng, Hua Dong, Xin-Ping Ai, Han-Xi Yang Nov 2004

The Investigation Of Bafesi/C Alloy Composite As Anode Materials For Li-Ion Battery, Rui-Xiang Feng, Hua Dong, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

A novel BaFeSi/C composite was prepared by mechanical ball milling, and lithium insertion reactions on the composite electrode were investigated by cyclic voltammetry , charge-discharge measurements, XRD and XPS spectroscopy. It is demonstrated that the capacity retention with indiscernible capacity decas during charge-discharge cycling. The improved cycling ability of the composite is suggested from a cooperative action by inactive FeSi2 and BaSi2 matrix and outer graphite shell, which both buffer the volumetric changes of the active Si phase and provide a good connection for electronic and ionic conduction during lithium insertion and extraction processes.

Go to article

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu Aug 2004

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu

Journal of Electrochemistry

The tungsten carbide (WC) electrode was constructed by using polyterafluoroethylene as binder. The electrochemical behavior of nitrobenzene on the WC electrode in acidic solution was investigated by cyclic voltammetry, linear scan method and chronoamperometry. Experimental results showed that WC electrode had good activity for the electrochemical reduction of nitrobenzene, and the electrode process was controlled by diffusion and electrochemical stepssimultaneously. The apparent active energy of the electrode process is 23.7kJ⋅mol-1, while the active energy of the electrochemicalstep is 10.91kJ⋅mol-1.

Go to article

Preparation And Electrochemical Performance Of New Composite Seperators For Lithium-Ion Batteries, Hu Cheng, Hong-Yan Du, Yong Yang Aug 2004

Preparation And Electrochemical Performance Of New Composite Seperators For Lithium-Ion Batteries, Hu Cheng, Hong-Yan Du, Yong Yang

Journal of Electrochemistry

New composite seperators for lithium ion batteries were prepared by coating PEO mixed with nanosize SiO2 onto microporous polypropylene(PP) seperators. Highly conductive electrolytes were prepared by soaking them in an electrolyte solution. With these composite separators, the lithium ion cell consisting of Li anode and LiNi0.8Co0.2O2 cathode were assembled. The high initial discharge capacity and good capacity retention were obtained through the cell.

Go to article

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen Aug 2004

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen

Journal of Electrochemistry

The electrocatalyst, Pt/MoO3 synthesized by solid state reaction, was used for the oxidation of methanol in direct methanol fuel cells. The X-Ray diffraction and cyclic voltammetry were employed to investigate the performance of the material. It was shown that the typical diffraction peaks for Pt appeared in XRD. And a good electrocatalysis for methanol oxidation was observed. The peak potential of the methanol oxidation appeared at ca. 0.63V(vs.SCE) and the peak current density for the oxidation was 78.1 mA⋅cm-2.

Go to article

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin Aug 2004

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO2(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO2(B) nanobelts electrode, and a high capacity (265 mAh·g-1) can be obtained. The results suggested that TiO2(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Go to article

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang Aug 2004

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion 115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion 115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

Go to article

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang Aug 2004

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang

Journal of Electrochemistry

Tape cast method was applied to prepare green sheets of Ni/YSZ anode supported YSZ thin film. After isostatic pressure treatment and cosintering, the YSZ film on the Ni/YSZ anode was gas-tight dense, and 15~30 μm thick. The area of the composite film was over 100 cm2. A Ce0.8Sm0.2O1.9 (CSO) interlayer was sintered on to the YSZ electrolyte film to protect La0.6Sr0.4CoO3 (LSCO) cathode from reaction with YSZ at high temperatures. The LSCO cathode layer was screen printed onto the CSO interlayer and sintered at 1200 ℃ for 3 …

Go to article

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan Aug 2004

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan

Journal of Electrochemistry

An intermediate temperature solid oxide fuel cell (IT-SOFC) was fabricated by co-copressing-sintering methods, and the electrolyte of Ce0.8Gd0.2O1.9 (CGO) and cathode materials of La0.6Sr0.4Co0.2Fe0.8O3-α (LSCF) were prepared by sol-gel method. The effect of preparation methods on the microstructure of the prepared fuel cells was analyzed by SEM . It shows that the cells prepared by the co-pressing/co-sintering method possess a dense electrolyte layer and a compact interface between electrolyte and anode but a curved configuration, while those prepared by the colloidal technique have a flat configuration …

Go to article

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu Aug 2004

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu

Journal of Electrochemistry

The synthesis of (S)-3-Phenylpropane-2-tert-butoxycarbonylamino-1-thiol(N-Boc-APT) from L-phenylalanine was reported. L-Phenylalanine was reduced to the corresponding amino alcohol, protection of the amino group using tert-butyl pyrocarbonate gave (S)-2-tert-butoxycarbonylamino-3-phenylpropane-1-ol, which was then O-mesylated and treated with potassium thioacetate in DMF to give 3-phenylpropane-2-tert- butoxycarbonylamino-1-etylmercapto. After the acetyl group was removed with ammonia in alcohol, the desired target molecular was obtained. The structure of intermediate and target molecular was conformed by IR and 1HNMR. We made N-Boc-APT self-assemble-modificated gold electrode and investigated its electrochemical behavior. The CV results of methylene blue on nano-Au/N-Boc-APT SAM/Au electrode showed that nano-Au could speed this electron transfer …

Go to article

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou Aug 2004

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

The Layered-structure LiMn1-xCrxO2(x=0, 0.15) solid solution has been prepared by the rheological phase method. From the XRD results, undoped LiMnO2 crystallized almost entirely in the orthorhombic phase while the structure of LiMn0.85Cr0.15O2 belongs to monoclinic phase. TEM investigation shows that the final powder product consists of ultrafine spherical particles which are distributed homogeneously, with the average diameter ranging from 60 to 300nm. The initial discharge capacity of LiMn0.85Cr0.15O is much higher than that of undoped LiMnO2. After 40 cycles, the capacity retention …

Go to article

Direct Electron Transfer Of Redox Proteins And Enzymes Promoted By Carbon Nanotube, Chen-Xin Cai, Jing Chen May 2004

Direct Electron Transfer Of Redox Proteins And Enzymes Promoted By Carbon Nanotube, Chen-Xin Cai, Jing Chen

Journal of Electrochemistry

The redox proteins (enzymes), such as hemoglobin (Hb), horseradish peroxidase (HRP) and glucose oxidase (GOx) were immobilized on the surface of the carbon nanotube modified with glassy carbon (CNT/GC) electrode, respectively. The experimental results showed that the redox proteins (enzymes) underwent effective and stable direct electron transfer reaction at the surface of CNT/GC electrode with a pair of nearly symmetrical redox peaks in phosphate buffer solution. The formal redox potential, E0' , is almost independent on the scan rates, the average value of E0'  for Hb, HRP and GOx is -0.343±0.001, -0.319±0.002 and -0.456±0.001 V (vs.SCE,pH 6.9), respectively. …

Go to article

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan May 2004

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan

Journal of Electrochemistry

A particularly designed H-type cell was used to simulate the operating condition of a hydrogen-air proton exchange membrane fuel cell (PEMFC). The electrocatalytic activity, morphology, structure and lifetime of commercially available catalysts, carbon support platinum (Pt/C) and unsupported platinum-ruthenium (Pt-Ru), were preliminary studied by carrying out electrochemical measurements and by SEM, XRD techniques. The catalysts were simultaneously tested in the H-cell under operation, and also separately tested in a conventional electrochemical cell for comparison. It was found that the characteristic peaks of hydrogen adsorption/desorption on cyclic voltammograms shifted considerably to a more positive direction for Pt/C, while a more negative …

Go to article

Electrochemical Lithium Insertion Of Nanosized Tio2, Ying Lan, Jian-Wen Liu, Xue-Ping Gao, Xing-Di Zhou, Jin-Qiu Qu, Feng Wu, De-Ying Song May 2004

Electrochemical Lithium Insertion Of Nanosized Tio2, Ying Lan, Jian-Wen Liu, Xue-Ping Gao, Xing-Di Zhou, Jin-Qiu Qu, Feng Wu, De-Ying Song

Journal of Electrochemistry

The protonic titanate nanotubes with the diameter of 10～15 nm were synthesized via hydrothermal method in NaOH solution and the calcined nanotubes at 500 ℃ were transferred to anatase nanorods with the diameter of 12～20 nm due to dehydration.The electrochemical behavior of the anatase nanorods as lithium insertion materials was examined. The results showed that the nanorod electrode had the high initial discharge capacity of 232 mAh/g and second reversible capacity of 198 mAh/g. The capacity of nanorod electrode maintained 152mAh/g after 20 cycles.

Go to article

Preparation, Characterization And Photoelectrochemical Activities Of Cu-Tio2/Ito Films, Dong Shu, Chun He, Han-Xia Zhang, Ya Xiong May 2004

Preparation, Characterization And Photoelectrochemical Activities Of Cu-Tio2/Ito Films, Dong Shu, Chun He, Han-Xia Zhang, Ya Xiong

Journal of Electrochemistry

Cu-TiO2/ITO films were prepared by direct photo-reduction deposition of Cu2+ on TiO2/ITO films. The nanocomposite films were characterized by UV-vis diffuse reflectance spectra (DRS), XRD spectra, Scanning Electron Microscope (SEM) technology, and photovoltage measurement. The feasibility of improving the photocatalytic activity of TiO2 film by combining the modification of Cu nanoparticles with the application of anodic bias was investigated. The experimental results showed that the deposited Cu has an apparent enhancement effect with respect to suppressing the recombination between the photogenerated charge carriers and enhancing the photocatalytic oxidation of formic acid. The combination could …

Go to article

Investigation Of Adsorption And Oxidation Behavior Of Isosafrole On A Smooth Pt, Xiao-Hong Zhang, Xiao-Jing Su, Qi-Ling Zhong, Lei Zhang, De-Sheng Mei, Bin Ren, Zhong-Qun Tian May 2004

Investigation Of Adsorption And Oxidation Behavior Of Isosafrole On A Smooth Pt, Xiao-Hong Zhang, Xiao-Jing Su, Qi-Ling Zhong, Lei Zhang, De-Sheng Mei, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

The electro-oxidation of isosafrole on a smooth platinum electrode was investigated in the non-aqueous solution. The CV curve shows two oxidation peaks and one reduction peak in the potential region between -0.5 V and 1.95 V. The relation between the oxidation and reduction peaks has been determined also by CV. The adsorption behavior of isosafrole on Pt was also investigated.

Go to article

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li May 2004

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li

Journal of Electrochemistry

The concentrationsof soluble Mn(Ⅲ) species, during the reduction ofelectrolytic MnO2 (EMD) in alkaline solution,have been monitored in situ by UV-visible spectroscopy. The concentration of Mn(Ⅲ) ion in solution changes with discharge time. The first electron discharge process of EMD can be described by three different steps: 1) the reduction of Mn4+ ions on the surface of EMD particles and the structural defect regions within the EMD, 2) the reduction of Mn4+ ions in ramsdellite, 3)the reduction of Mn4+ ions in pyrolusite. During the second electron discharge of EMD, the soluble Mn(Ⅲ) is reduced to Mn(Ⅱ) , …

Go to article

Stability And Electrochemical Performance Of Nio Cathode Modified By Zno Additive For Mcfc In Molten Carbonates, Bo Huang, Fei Li, Qing-Chun Yu, Gang Chen, Ke-Ao Hu May 2004

Stability And Electrochemical Performance Of Nio Cathode Modified By Zno Additive For Mcfc In Molten Carbonates, Bo Huang, Fei Li, Qing-Chun Yu, Gang Chen, Ke-Ao Hu

Journal of Electrochemistry

The ZnO/Ni composite cathode was fabricated by tape-casting method, which microstructures and phases were studied. The electrochemical behaviors of ZnO impregnated NiO cathodes were also evaluated in molten 62 mol%Li2CO3 + 38 mol%K2CO3eutectic at 650 ℃ by electrochemical impedance spectroscopy (EIS) as a function of ZnO content and immersion time. The ZnO impregnated nickel cathodes showed the similar porosity, pore size and morphology to the reference nickel cathode. The stability tests of ZnO impregnated NiO cathodes showed that the ZnO additive could dramatically reduce the solubility of NiO in a eutectic carbonate mixture …

Go to article

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian Feb 2004

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian

Journal of Electrochemistry

The monocrystalline metal nanowire arrays were prepared by using a two-step AC electrodeposition in porous anodic aluminum oxide (AAO) template. The growth mechanism of nanowires was discussed. As a result, it has been found that the second voltage pulse has a considerable effect on the pore-filling ratio, the uniformity and the crystal structure, whereas the initial voltage pulse affects only the pore-filling ratio. Using the two-step AC electrodeposition, a highly ordered monocrystalline metal nanowire arrays with a pore-filling ration above 95% can be easily obtained.

Go to article

Study On Determination Of Iodine Ion At Chitosan Modified Glassy Carbon Electrode, Bin Liu, Xiang-Ying Sun, Jin-Rui Xu Feb 2004

Study On Determination Of Iodine Ion At Chitosan Modified Glassy Carbon Electrode, Bin Liu, Xiang-Ying Sun, Jin-Rui Xu

Journal of Electrochemistry

In this paper, a chitosan modified glassy carbon electrode was prepared by the method of covalent-bond reaction, and the anodic stripping voltammetric characteristics of iodine on the modified electrode was studied. The results showed that the modified electrode has higher adsorption and selectivity for I- , and the sensitivity for I-  has been much improved in 0.1 mol·L-1 KH2PO4 solution (pH=4.0). The anodic stripping peak current of I- on the modified electrode varied linearly with I-  concentration in the range of 2.0×10-6～2.0×10-3 mol·L-1, and the detection limit …

Go to article

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu Feb 2004

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu

Journal of Electrochemistry

The electroreduction mechanism of oxalic acid on Pb electrode in Na2SO4 solution were investigated using high scan rate cyclic voltammetry and chronoamperometry. The dynamic parameters for the first step electron transter reaction of oxalic acid electroreduction by were determined. The corresponding reduction peak potentials of oxalic acid, glyoxylic acid and glycolic acid in the cyclic voltammogranis obtained in the same condition were compared, and the intermediate reduction products of oxalic acid were suggested. The results showed that oxalic acid is weakly absorbed on the lead electrode.

Go to article

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma Feb 2004

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma

Journal of Electrochemistry

In this paper, Pt/CNTs catalyst was prepared and its electrocatalytic property was studied by obtaining cycling voltammetry curves (C-V) and Tafel curves. In addition, the XRD,XPS and TEM tests were carried out to determine the structure and composition of the catalysts. It can be found that the platinum loading has been increased significantly using a carbon nanotubes support. Dispersion of Platinum was better and gave more active sites. The electrochemical characteristic of Pt/CNTs was also more desirable than that of Pt/C catalys t(Johnson Matthey). In conclusion, carbon nanotubes can played a conspicuous role in "electrogenerative" processes of PEMFC hydrogenation reactor.

Go to article

The Interaction In Doping Lithium Of Carbonaneous Anode In Lithium Ion Battery, Chang-Guo Chen, Hong-Min Zhang, Jia Chen, Dan-Mei Yu Feb 2004

The Interaction In Doping Lithium Of Carbonaneous Anode In Lithium Ion Battery, Chang-Guo Chen, Hong-Min Zhang, Jia Chen, Dan-Mei Yu

Journal of Electrochemistry

The quantum chemical DV-Xα method was used to calculate the lithium-doped models from one-Li-dopant to LiC6 and LiC2. It was found that Li+ has an tendency to attract electrons from the carbon plane through the C6 hexagons lying above or below it by the graph of charge-density difference. It was shown that LiC6 can exist steadily,while LiC2 can not exist steadily.

Go to article

First Prev Next Last