Materials Science and Engineering Commons^™

Cure Kinetics, Morphologies, And Mechanical Properties Of Thermoplastic/Mwcnt Modified Multifunctional Glassy Epoxies Prepared Via Continuous Reaction Methods, Xiaole Cheng

Dissertations

The primary goal of this dissertation is to develop a novel continuous reactor method to prepare partially cured epoxy prepolymers for aerospace prepreg applications with the aim of replacing traditional batch reactors. Compared to batch reactors, the continuous reactor is capable of solubilizing and dispersing a broad range of additives including thermoplastic tougheners, stabilizers, nanoparticles and curatives and advancing epoxy molecular weights and viscosities while reducing energy consumption.

In order to prove this concept, polyethersulfone (PES) modified 4, 4’-diaminodiphenylsulfone (44DDS)/tetraglycidyl-4, 4’-diaminodiphenylmethane (TGDDM) epoxy prepolymers were firstly prepared using both continuous reactor and batch reactor methods. Kinetic studies confirmed the chain …

Electrospinning Of Polycaprolactone Core-Shell Nanofibers With Anti-Cancer Drug, Sakib Iqbal, Mujibur Khan, Saheem Absar, Andrew Diamanduros, Samuel Chambers

GS4 Student Scholars Symposium

Encapsulation of a model anti-cancer drug, 5-Fluorouracul (5-FU) into biocompatible core-shell nanofibers of polycaprolactone (PCL) nanofibers was fabricated using a coaxial electrospinning process. Our work aims to solve these issues using a novel method of fabrication of fibers featuring confinement of drugs within a biodegradable core-shell structure, thereby permitting sustained release of drugs to specific sites of treatment, such as tissues affected with tumor cells. The coaxial electrospinning was performed using a sheath polymer solution consisting of a 14 wt% PCL solution and a 5 wt% solution of 5-FU as the core solution. Dimethylformamide (DMF) was used as the solvent …

Optimization Of Graphene-Based Materials Outperforming Host Epoxy Matrices, Liberata Guadagno, Marialuigia Raimondo, Luigi Vertuccio, Marco Mauro, Gaetano Guerra, Khalid Lafdi, Biagio De Vivo, Patrizia Lamberti, Giovanni Spinelli, Vincenzo Tucci

Chemical and Materials Engineering Faculty Publications

The degree of graphite exfoliation and edge-carboxylated layers can be controlled and balanced to design lightweight materials characterized by both low electrical percolation thresholds (EPT) and improved mechanical properties. So far, this challenging task has been undoubtedly very hard to achieve.

The results presented in this paper highlight the effect of exfoliation degree and the role of edge-carboxylated graphite layers to give self-assembled structures embedded in the polymeric matrix. Graphene layers inside the matrix may serve as building blocks of complex systems that could outperform the host matrix. Improvements in electrical percolation and mechanical performance have been obtained by a …

Process And Apparatus For Manufacturing Grease, Lou A. T. Honary, James E. Wesley

Patents (University of Northern Iowa)

A process and corresponding apparatus and system for use in preparing soaps from fatty acid containing oil compositions, and in turn, for preparing greases by the use of such soaps in combination with one or more base oils.

Methods For Analyzing The Structure Of Creases In Heat Sealed Paperboard Packages, Ville Leminen, Petri Mäkelä, Panu Tanninen, Juha Varis

Journal of Applied Packaging Research

Press-forming of paperboard has been previously studied by several authors. A point of interest regarding gas tight heat sealing of the packages are the creases in the package. The objective of this article was to study and compare different microscopic imaging methods to research an optimal imaging method for the formation of creases in the press-forming process of polymer coated paperboard trays. The studied methods were: Scanning electrode microscopy (SEM), X-ray Microtomography, Optical light microscopy and Polarized light microscopy. All four tested methods delivered clear images. Casting of the samples in an acrylic resin and light microscope imaging was found …

Computational Multiscale Modeling And Characterization Of Piezoresistivity In Fuzzy Fiber Reinforced Polymer Composites, Xiang Ren, Josh Burton, Gary D. Seidel, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In this paper, the piezoresistive response (i.e. the change of resistance under the application of strain) of polymer composites reinforced by a novel material known as fuzzy fibers is characterized by using single tow piezoresistive fragmentation tests and modeled by using a 3D computational multiscale model based on the finite element analysis. In the characterization work, the fuzzy fiber tow is embedded in a dog-bone specimen infused by epoxy, with resistance and displacement measured simultaneously to obtain its piezoresistive response. An approximately linear and stable piezoresistive response is observed within the fuzzy fiber tow region yielding gauge factors on average …

Design And Synthesis Of Low-Bandgap Polymers For Organic Photovoltaic Applications, Letian Dou

Link Foundation Energy Fellowship Reports

This research at UCLA focused on the design and synthesis of novel conjugated polymers as the electron-donor material for photovoltaic devices. By careful molecular design both on the polymer backbone and the side chains, a series of low-bandgap conjugated polymers were synthesized for a variety of photovoltaic applications, including single junction and tandem polymer solar cells. In addition, the author designed and synthesized a novel higly perfect polymer single crystal material via a visible light triggered topochemical reaction. This kind of materials shows high potential for application in solar cells and transistors, which, the author believe, is a huge breakthrough …

Characterization Of Dimethyl Sulfoxide-Treated Wool And Enhancement Of Reactive Wool Dyeing In Non-Aqueous Medium, Luyi Chen, Bijia Wang, Jiangang Chen, Xinhui Ruan, Yiqi Yang

Department of Textiles, Merchandising and Fashion Design: Faculty Publications

Wool pretreated with dimethyl sulfoxide (DMSO) was characterized and its dyeing behavior in non-aqueous green solvents was investigated. Reactive dyeing of wool in deep shades is challenging because the mandatory alkaline aftertreatment to match the fastness of mordant dyes inevitably causes damage to wool keratin. The current study showed that the colorfastness-integrity dilemma could be solved by replacing water with organic solvents as the dyeing medium. Covalent fixation is predominantly favored in solvent dyeing so that excellent colorfastness is achievable at any given shade without alkali aftertreatment. Compared with aqueous dyeing, solvent dyeing was found to give 30% higher covalent …

Temporally And Spatially Resolved Plasma Spectroscopy In Pulsed Laser Deposition Of Ultra-Thin Boron Nitride Films, Nicholas R. Glavin, Christopher Muratore, Michael L. Jespersen, Jianjun Hu, Timothy S. Fisher, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

Physical vapor deposition (PVD) has recently been investigated as a viable, alternative growth technique for two-dimensional materials with multiple benefits over other vapor deposition synthesis methods. The high kinetic energies and chemical reactivities of the condensing species formed from PVD processes can facilitate growth over large areas and at reduced substrate temperatures. In this study, chemistry, kinetic energies, time of flight data, and spatial distributions within a PVD plasma plume ablated from aboron nitride (BN) target by a KrF laser at different pressures of nitrogen gas were investigated. Time resolved spectroscopy and wavelength specific imaging were used to identify and …

Effects Of Disorder State And Interfacial Layer On Thermal Transport In Copper/Diamond System, Vikas Sinha, Jaime J. Gengler, Christopher Muratore, Jonathan E. Spowart

Chemical and Materials Engineering Faculty Publications

The characterization of Cu/diamond interface thermal conductance (h_c) along with an improved understanding of factors affecting it are becoming increasingly important, as Cu-diamond composites are being considered for electronic packaging applications. In this study, ∼90 nm thick Cu layers weredeposited on synthetic and natural single crystal diamond substrates. In several specimens, a Ti-interface layer of thickness ≤3.5 nm was sputtered between the diamond substrate and the Cu top layer. The h_c across Cu/diamond interfaces for specimens with and without a Ti-interface layer was determined usingtime-domain thermoreflectance. The h_c is ∼2× higher for similar interfacial layers on …

Effect Of Nanofiber Morphology On Pvdf Air Filter Performance, Andrew W. Marton

Williams Honors College, Honors Research Projects

Poly(vinylidene fluoride) (PVDF) can be formed into small nanofibers by electrospinning that are useful for a variety of applications. Air filters produced with PVDF are known to capture ionic particles with high efficiency. Existing studies have focused on the effects of electrospinning conditions on nanofiber morphology. In this study fibers were generated with varying morphologies. Air filters were then made from each sample and then characterized by TSI. Air filters were found to have increased resistances relative to their capture efficiencies according to particle diameter. Capture efficiencies did not correlate strongly with particle diameter, and the presence of beads in …

The Future Of Carbon-Based Scaffolds In Foot And Ankle Surgery, Jarema S. Czarnecki, Khalid Lafdi, Panagiotis A. Tsonis

Chemical and Materials Engineering Faculty Publications

Autologous grafts have been the gold standard in tissue replacement and the most accurate means of recapitulating both the biological and mechanical properties of tissue. However, autologous grafts have had complications and drawbacks. Skin grafting, a prime example of an autologous tissue graft, has been limited by the size of graft, availability, and secondary donor site morbidity. Use of cadaveric tissues circumvents several limitations of autologous grafts; however, sterilization processes used to reduce the risk of disease transmission potentially weaken tissues and eliminate living cells and some growth factors from scaffolds, making them suboptimal tissue replacements. Chemical cross-linkage of tissue …

Designed Synthesis Of Nanoporous Organic Polymers For Selective Gas Uptake And Catalytic Applications, Pezhman Arab

Theses and Dissertations

Design and synthesis of porous organic polymers have attracted considerable attentions during the past decade due to their wide range of applications in gas storage, gas separation, energy conversion, and catalysis. Porous organic polymers can be pre-synthetically and post-synthetically functionalized with a wide variety of functionalities for desirable applications. Along these pursuits, we introduced new synthetic strategies for preparation of porous organic polymers for selective CO₂ capture.

Porous azo-linked polymers (ALPs) were synthesized by an oxidative reaction of amine-based monomers using copper(I) as a catalyst which leads to azo-linkage formation. ALPs exhibit high surface areas of up to 1200 …

Evaporation-Induced Formation Of Well-Ordered Surface Patterns On Polymer Films, Wei Sun

Theses and Dissertations--Chemical and Materials Engineering

Various techniques of fabricating surface patterns of small scales have been widely studied due to the potential applications of surface patterns in a variety of areas. It is a challenge to fabricate well-ordered surface area efficiently and economically. Evaporation-induced surface patterning is a promising approach to fabricate well-ordered surface patterns over a large area at low cost. In this study, the evaporation-induced surface patterns with controllable geometrical characteristics have been constructed. The dewetting kinetics on deformable substrate is also investigated.

Using simple templates to control the geometry and the evaporation behavior of a droplet of volatile solvent, various gradient surface …

Reusable Adhesive Tapes From Electrospun Polymer Fibers, Vishal K. Chaurasia

Williams Honors College, Honors Research Projects

Many emerging applications demand an adhesive that has reusable properties. The adhesive must exhibit high adhesion strength to various surfaces and be able to be removed easily and then reapplied with minimal to no loss in adhesion strength. This work aims to tackle this problem by creating an adhesive tape fabricated by electrospinning polymer solutions onto a substrate. Electrospun adhesive nano/micro fibers have the ability to display the reusable characteristics desired. Several adhesive custom formulations were first developed and optimized for electrospinning. Then these formulations were successfully electrospun on to various substrates after much fine tuning of electrospinning parameters. The …

Peracetic Acid Sterilization Of Electrospun Polycaprolactone Scaffolds, Suyog Yoganarasimha

Theses and Dissertations

Sterilization of tissue engineered scaffolds is an important regulatory issue and is at the heart of patient safety. With the introduction of new biomaterials and micro/nano structured scaffolds, it is critical that the mode of sterilization preserve these built-in features. Conventional sterilization methods are not optimal for engineered polymeric systems and hence alternate systems need to be identified and validated. PCL is polyester with a low melting point (heat labile), susceptible to hydrolysis and is popular in tissue engineering. Electrospinning generates some nanoscale features within the scaffold, the integrity of which can be affected by sterilization method. Chapter 1 explores …

The Influence Of Particle Content On The Equi-Biaxial Fatigue Behaviour Of Magnetorheological Elastomers, Yanfen Zhou, Stephen Jerrams, Tony Betts, Gerald Farrell, Lin Chen

Articles

The equi-biaxial fatigue behaviour of silicone based magnetorheological elastomers (MREs) with various volume fractions of carbonyl iron particles ranging between 15% and 35% was studied. Wöhler curves for each material were derived by cycling test samples to failure over a range of stress amplitudes. Changes in complex modulus (E*) and dynamic stored energy during the fatigue process were observed. As for other elastic solids, fatigue resistance of MREs with different particle contents was shown to be dependent on the stress amplitudes applied. MREs with low particle content showed the highest fatigue life at high stress amplitudes while MREs with high …

Systematic Study Of The Biological Effects Of Nitric Oxide (No) Using Innovative No Measurement And Delivery Systems, Weilue He

Dissertations, Master's Theses and Master's Reports

Nitric oxide (NO) is recognized as the most important small signaling molecule in the human body. An imbalance of NO is closely associated with many serious diseases such as neurological disorders, cardiovascular diseases, chronic inflammations and cancers. Herein two chemiluminescence-based devices (a real-time NO measurement device and a controllable NO delivery device) were developed to facilitate the NO quantitative study and obtain information for NO related drug design.

The first device used for real-time measuring NO(g) flux from living cells was developed and validated. The principle was to use a two-chamber design, with a cell culture chamber and a gaseous …

3d Printing, Open-Source Technology And Their Applications In Research, Chenlong Zhang

Dissertations, Master's Theses and Master's Reports

Open-source software received tremendous success as it drives down the cost of software and expand the distribution. Open-source hardware, as part of the open-source movement, has just risen into public attention for its potential to further drive down the cost of all kinds of manufacturing goods and reshape the manufacture chain. In this report we explores the history, development and the future of open-source hardware project, summarizing the opportunities, challenges and possible solutions. 3D printing is demonstrated as a booster to assist open-source hardware’s development. Low-cost 3D printer enables at-home and in-time fabrication, the download-print-use-improve-distribute cycle is established to encourage …

Failure Modes For I-Section Gfrp Beams, Mamadou Konate, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents calculations for the failure modes for I-section Glass Fiber Reinforced Polymer (GFRP) beams with single mid-span web brace. Theoretical predictions are made using ASCE-LFRD Pre-Standard for FRP structures. For the member length considered, it is found that for small and medium I-sections the failure mode is governed by lateral-torsional buckling and for bigger I-sections the failure mode is governed by material rupture. The outcome of the predicted lateral-torsional buckling mode is compared with that observed experimentally.

Influence Of The Temperature On Flow-Induced Crystallization Of Isotactic Polypropylene And Propylene–Ethylene Random Copolymer, Hugo Boitout

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

When flow is applied on a semi-crystalline polymer melt, it can greatly impact how it crystallizes its final properties. Therefore, it is crucial to understand the basic mechanism of flow induced crystallization (FIC). Only then will it be possible to predict final properties from the type of resin and processing conditions. Polypropylene is one of the most widely used polymers. Its processing generally involves subjecting the melt to intense flow fields, so FIC commonly occurs.

This study investigates the influence of temperature of shear and crystallization on the FIC behavior of isotactic polypropylene (iPP). Temperature is one of the main …

Utilization Of Aqueous Raft Prepared Copolymers To Improve Anticancer Drug Efficacy, Andrew Christopher Holley

Dissertations

The advent of controlled radical polymerization (CRP) techniques, along with advancements in facile conjugation chemistry, now allow synthetic tailoring of precise, polymeric architectures necessary for drug/gene delivery. Reversible addition- fragmentation chain transfer (RAFT) polymerization and its aqueous counterpart (aRAFT) afford quantitative control over key synthetic parameters including block length, microstructure, and placement of structo-pendent and structo-terminal functionality for conjugation of active agents and targeting moieties. The relevance of water-soluble and amphiphilic (co)polymers synthesized by RAFT for in vitro delivery of therapeutics in biological fluids is an especially attractive feature. In many cases, polymerization, binding, conjugation, …

The Development Of A Laminated Copolyester Electric Guitar, Addison S. Karnes

Electronic Theses and Dissertations

This thesis is an investigation of the fabrication and assembly methodologies employed in the development of a proof-of-principle prototype electric guitar composed of laminated copolyester. The objective of the project was to develop the processes and procedures to create an optimized physical and visual bond between layers to minimize vibratory dissipation, thus maximizing sustain. A high speed CNC router, abrasive waterjet, laser engraver-cutter, as well as various manual fabrication and assembly methods were investigated in the construction of the guitar prototypes. The lamination processes explored include low-temperature, heat-assisted pressure bonding, solvent and chemical welding, and contact adhesives. The project concluded …

Wear Resistant Polydopamine/Ptfe Nanoparticle Composite Coating For Dry Lubrication Applications, Samuel George Beckford

Graduate Theses and Dissertations

This dissertation presents an investigation into the effect of nanoparticle fillers and a polydopamine adhesive primer on the tribological performance of thin PTFE films. The principal objective of this investigation was to reduce wear in PTFE films, an issue which precludes the use of PTFE films in tribological applications requiring high durability. The friction and wear of the composite films were evaluated using a ball-on-flat configuration in linear reciprocating motion. It was found that the use of a polydopamine adhesive primer reduces the wear of PTFE films more than 600 times. X-ray photoelectron spectroscopy (XPS) results show that a tenacious …

Metal Assisted Nanowire Growth For Silicon Nanowire/Amorphous Silicon Composite Solar Cell, Asmaa Ali Sadoon

Graduate Theses and Dissertations

Solar cells are photovoltaic devices that convert the energy of light to electricity by the photovoltaic effect. Crystalline silicon-based solar cells are the most dominant solar cells in the market today due to the high efficiency and relatively low cost. However, the cost of such solar cell is still high due to the large amount of material that is consumed in fabricating such a device. Polycrystalline/amorphous thin films and nanomaterial technologies have emerged to reduce the high cost of c-Si based solar cells and increase the efficiency. In this research, we combined these two technologies to propose and fabricate silicon …

Growth And Properties Of Carbon Microcoils And Nanocoils, Muneaki Hikita, Robyn Bradford, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Various types of coiled carbon filaments have been synthesized using chemical vapor deposition and other methods. These carbon filaments exhibit unique electrical and mechanical properties due to their versatile shapes and structures. To form coiled shapes, different types of catalyst compositions and reactive gases have been explored. Generally, coiled carbon filaments are classified by coil diameter and shape (e.g., microcoil and nanocoil). In this review, coiled carbon filaments are classified into three growth mechanism categories:

(1) bidirectional double helical growth;

(2) bidirectional twisted growth; and

(3) tip single helical or twisted growth.

Next, their synthesis methods and hypothetical growth mechanisms …

Slow Release Of Ions From Internalized Silver Nanoparticles Modifies The Epidermal Growth Factor Signaling Response, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

Due to their distinctive physiochemical properties, including a robust antibacterial activity and plasmonic capability, hundreds of consumer and medical products contain colloidal silver nanoparticles (AgNPs). However, even at sub-toxic dosages, AgNPs are able to disrupt cell functionality, through a yet unknown mechanism. Moreover, internalized AgNPs have the potential to prolong this disruption, even after the removal of excess particles. In the present study, we evaluated the impact, mechanism of action, and continual effects of 50 nm AgNP exposure on epidermal growth factor (EGF) signal transduction within a human keratinocyte (HaCaT) cell line. After AgNP expose, EGF signaling was initially obstructed …

Effect Of Plasticizer On Oxygen Permeability Of Cast Polylactic Acid (Pla) Films Determined Using Dynamic Accumulation Method, Kurniawan Yuniarto, Bruce A. Welt, Aris Purwanto, Hadi Karia Purwadaria, Ayman Abdellatief, Titi C. Sunarti, Setyo Purwanto

Journal of Applied Packaging Research

Polylactic acid (PLA) is becoming an increasingly important biopolymer for packaging applications. PLA brittleness limits its applicability. This study evaluated PLA properties with increasing amounts of added polyethylene glycol (PEG) plasticizer. Oxygen transmission rate (OTR) of cast films was determined using the newly available Dynamic Accumulation (DA) method. Arrhenius temperature sensitivity of OTR and polymer Permeability was also determined. Permeability of neat PLA is 4.848 ml mm (STP)/m² s kPa; hence, 4.84 ml mm (STP)/m² s kPa, 4.07 ml mm (STP)/m² s kPa and 5.42 ml mm (STP)/m² s kPa by adding PEG 1 %, 5% …

Simulation Studies Of Organic Solar Cell Structure And Morphology On The Device Efficiency, Satish Kumar Reddy Kota

Electrical & Computer Engineering Theses & Dissertations

Solar cells based on organic materials offer several advantages over the traditional solar cells made with inorganic materials. These include a lower impact on nature, smaller weight, the avoidance of cleanrooms for their production, their flexibility which makes it possible to wrap or coat them on objects with varying shapes and geometries, and most significantly their ability to produce electricity in diffuse'd light which is a distinct advantage over conventional solar cells. Organic solar cells have their own disadvantage of very low efficiencies as compared to inorganic solar cells. The morphology and structure of the organic solar cells plays a …

Humic Substances-Based Polymer System, Gerard R. Thiel

Patents (University of Northern Iowa)

A system for use in forming polymer compositions, including as a replacement for phenolic based resin systems, for instance, in preparing foundry molds. In a preferred embodiment, the system includes the use of a) a polyermizable hydroxyl-containing component comprising a humic substance (as can be provided by lignite), b) an isocyanate component, and c) a catalyst, and preferably amine catalyst, component adapted to catalyze the polymerization of a) and b). The system is optionally used as binder system in the presence of a filler, such as, in combination with a foundry aggregate such as sand. A polymer system of this …