Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Polymer and Organic Materials

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 271 - 300 of 957

Full-Text Articles in Materials Science and Engineering

Predictive Thermal Modeling And Characterization Of Ultrasonic Consolidation Process For Thermoplastic Composites, Madeline Kirby Jul 2022

Predictive Thermal Modeling And Characterization Of Ultrasonic Consolidation Process For Thermoplastic Composites, Madeline Kirby

LSU Master's Theses

Ultrasonic consolidation (USC) of thermoplastic composites (TPCs) is a highly attractive and promising method to manufacture high-performance composites. This work focuses on USC of dry carbon fiber (CF) fabrics with high-temperature polyphenylene sulfide (PPS) films. Experimental trials to assess feasibility of the process are time-consuming. Consequently, a predictive thermal model would facilitate process parameters selection to reduce expensive trial-and-error approaches. This paper presents a 2D finite element model of samples under consolidation, incorporating equations for viscoelastic heating, matrix phase change, and material properties. Theoretical temperature profiles for nodes of interest were compared to the corresponding experimental temperature curves for various …

Go to article

Photon Attenuation Layer Silicon-Based X-Ray Detector: Quantum Efficiency Investigation And Algorithmic Processing Of Individual Detection Events, Kevin Larkin Jun 2022

Photon Attenuation Layer Silicon-Based X-Ray Detector: Quantum Efficiency Investigation And Algorithmic Processing Of Individual Detection Events, Kevin Larkin

ENGS 88 Honors Thesis (AB Students)

State-of-the-art X-ray detectors either use silicon direct detection—which is inefficient, as silicon is mostly transparent to high-energy X-rays—or rely on expensive scintillators to first down-convert X-ray photons to lower energies. Dr. Eldred Lee of Dartmouth College recently completed doctoral research that suggested the promise of a novel alternative: silicon-based X-ray detectors that utilize photon attenuation layers rather than scintillators. While Dr. Lee’s work is certainly rigorous and meritorious, background noise controls were rendered less effective by circumstances. The work presented in this thesis succeeded in implementing much better background noise controls for a series of new tests to compare the …

Go to article

Bbt Side Mold Assy, Bill Hemphill Jun 2022

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …

Go to article

Stabilization Of Palm Wood Using Water-Based Impregnation, David A. Barnes Jun 2022

Stabilization Of Palm Wood Using Water-Based Impregnation, David A. Barnes

Materials Engineering

Impregnation is a technique for stabilizing wood that involves saturating the material in a liquid and allowing it to cure before use. Stabilization methods such as this are employed for a variety of reasons; chiefly, the low dimensional stability of wood and palm means that they are subject to several failure modes that arise from changing environmental conditions, such as cracking, warping, and bending. Samples of Borassus flabellifer, black palm, provided by DuraPalm were impregnated with solvent-based and water-based stabilizers, and untreated wood samples used as a control group. Kop-Coat WoodYouth® Plus was used as a solvent-based stabilizer, and impregnation …

Go to article

Effects Of Release Materials And Temperature Ramp Rates On The Surface Finish Of Carbon-Fiber Composite Components, Sudeep Louis, Thucmy Dang, Ethan Schlocker Jun 2022

Effects Of Release Materials And Temperature Ramp Rates On The Surface Finish Of Carbon-Fiber Composite Components, Sudeep Louis, Thucmy Dang, Ethan Schlocker

Materials Engineering

Toray Advanced Composites is interested in improving their carbon fiber reinforced polymers (CFRP) manufacturing process by enhancing their control on the amount of surface roughness for varied customer preference. Surface roughness of CFRP is important in post-production processes including coating, priming, and painting. This project seeks to determine the effects of three release materials and two temperature ramp rates on the surface finish of CFRP. The release materials used were Tooltech, FEP, and Frekote 770-NC. The two initial temperature ramp rates were 1°F/min and 2°F/min. Surface roughness was measured using a profilometer and analyzed using Ra values. Ra is an …

Go to article

Analysis Of Novel Corrosion Resistant Maraging Steels For Use In Additive Manufacturing, Bradley Michael Samuel, James Knowlton Smith Jun 2022

Analysis Of Novel Corrosion Resistant Maraging Steels For Use In Additive Manufacturing, Bradley Michael Samuel, James Knowlton Smith

Materials Engineering

Stainless maraging steel has been proven to be an industry standard material for plastic injection molds. Its high hardness and corrosion resistance extend the lifetime of the tool. This alloy system is also well-suited to additive manufacturing, which can be utilized to form internal cooling channels, further increasing tool life. Using Rapid Alloy Development (RAD) Oerilkon METCO is developing a new composition of stainless maraging tool steel that has high hardness/strength, is corrosion resistant, and has additive-capable melting and solidification properties. This study tests the hardness and corrosion resistance of the new RAD alloys against the current market competitor Corrax …

Go to article

In Situ Marine Biodegradation Of Poly(Lactic) Acid And Thermoplastic Starch Blends, Brittany Denicholas Jun 2022

In Situ Marine Biodegradation Of Poly(Lactic) Acid And Thermoplastic Starch Blends, Brittany Denicholas

Materials Engineering

Marine life has been suffering from macro- and microplastics since the inception of petroleum-based plastic. Bio-based biodegradable polymers such as PLA and TPS can help mitigate the damage done by petroleum plastics. Blending PLA and TPS can reduce the cost while preventing a significant effect on the material properties. PLA/TPS blend compositions such as 90/10, 80/20, 70/30 could be candidates for a solution. The PLA/TPS blends have been submerged in a marine environment at the Cal Poly Pier in Avila Beach for 8 weeks. Three sample sets containing three of each blend composition were collected every week and tested in …

Go to article

Citric Or Acetic Acid Effects On The Crosslinking Of Pvoh, Samuel Carr, Erika Szaldobagyi Jun 2022

Citric Or Acetic Acid Effects On The Crosslinking Of Pvoh, Samuel Carr, Erika Szaldobagyi

Materials Engineering

Transportation and shipping processes are the most dangerous times for food due to harsh handling and frequent temperature changes. Plain corrugated boxes cannot withstand the damp environment caused by melting ice that is used to keep foods cold and fresh. To minimize damage, a protective polymer film coating can be applied. These coatings can be unsafe when used with food and will lead to excess waste by limiting the recyclability of the boxes. The purpose of this project was to produce nontoxic crosslinked PVOH films to determine suitability for a cost effective, biodegradable, and repulpable corrugated box coating. Polyvinyl alcohol …

Go to article

Determining The Efficacy Of A Silica And Bacterial Cellulose Composite Model System, Hannah Martin, Daisy Kamp Jun 2022

Determining The Efficacy Of A Silica And Bacterial Cellulose Composite Model System, Hannah Martin, Daisy Kamp

Materials Engineering

Bacterial cellulose (BC) is a sustainable alternative to petroleum-based polymer films for synthetic leather applications. Synthesized by a symbiotic culture of bacteria and yeast, BC is a three-dimensional structure composed of cellulose microfibrils. However, pure BC lacks certain desirable properties such as high tensile strength. Previous studies have shown that loading BC with nanoparticles to form nanocomposites has improved BC’s mechanical properties. However, this was not studied as a function of particle size. This study focuses on using silica/BC nanocomposites to model the impact that particle size and silica soaking concentrations have on the uptake efficiency of these particles into …

Go to article

Soil Degradation Of A Plastic Blend Of Opuntia Ficusindica Juice, Animal Protein And Beeswax, Isabel A. Gamez, Daniel R. Kava Jun 2022

Soil Degradation Of A Plastic Blend Of Opuntia Ficusindica Juice, Animal Protein And Beeswax, Isabel A. Gamez, Daniel R. Kava

Materials Engineering

Since the introduction of single use plastics in the early 1900s, their usage has increased exponentially. Unfortunately, due to this exponential increase there are negative environmental implications of their production, which requires further consideration. Currently, there are various waste disposal practices for SUPs, including landfilling, incineration, and recycling. Recent data revealed that only 14 % of plastic waste was recycled, with 40% of plastic waste being landfilled, while the rest of the plastic waste was incinerated or released to the environment at 14 % and 32 %, respectively. A potential solution to the plastic waste issue is developing a polymer …

Go to article

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter Jun 2022

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Go to article

Text Summarization Towards Scientific Information Extraction, Abigail Keller May 2022

Text Summarization Towards Scientific Information Extraction, Abigail Keller

College of Computing and Digital Media Dissertations

Despite the exponential growth in scientific textual content, research publications are still the primary means for disseminating vital discoveries to experts within their respective fields. These texts are predominantly written for human consumption resulting in two primary challenges; experts cannot efficiently remain well-informed to leverage the latest discoveries, and applications that rely on valuable insights buried in these texts cannot effectively build upon published results. As a result, scientific progress stalls. Automatic Text Summarization (ATS) and Information Extraction (IE) are two essential fields that address this problem. While the two research topics are often studied independently, this work proposes to …

Go to article

Copolymer Microphase Separation, Properties, And Applications, Daniel Weller May 2022

Copolymer Microphase Separation, Properties, And Applications, Daniel Weller

Dissertations

Copolymers represent a broad, but critically important class of materials. Often having properties superior to either of its constituents, copolymers are used in virtually all industries including automotive, aerospace, coatings, packaging, and cosmetics. Certain copolymers microphase separate to form nanosized domains that improve the physical properties of the copolymer. The polymer community already has a thorough understanding of how phase separation occurs, but the commercialization of phase separating copolymers lags significantly behind academia. Many of the copolymers that exist that have been undercharacterized and underutilized. This dissertation examines two such polymers. The first, a hard polystyrene material with soft nanodomains. …

Go to article

Receptor-Doped Organic Transistors: Transducing Anion Binding From Mixed Ionic-Electronic Transport, Anthony Benasco May 2022

Receptor-Doped Organic Transistors: Transducing Anion Binding From Mixed Ionic-Electronic Transport, Anthony Benasco

Dissertations

Organic semiconductors based on π-conjugated polymers show remarkable properties such as high tolerance to structural defects, low processing temperature requirements, biocompatibility, ease of fabrication, and tunable properties. Conjugated polymers integrated into device arrays can exhibit collective properties sensitive to minor perturbations in the surrounding media. However, these devices rely on serendipitous sensitivity to the analyte of interest, and strategies for specific detection remain a considerable change. There remains a compelling, global need for technologies to monitor phosphate due to its prevalence in agricultural runoff, leading to fish kills and economic decline for commercial and recreational fisheries. The strong hydration energies …

Go to article

Biodegradable Active Bio-Nanocomposite Film For The Enhanced Shelf Life Of Tomatoes, Kalpani Y. Perera, Shubham Sharma, Brendan Duffy, Amit K. Jaiswal, Swarna Jaiswal May 2022

Biodegradable Active Bio-Nanocomposite Film For The Enhanced Shelf Life Of Tomatoes, Kalpani Y. Perera, Shubham Sharma, Brendan Duffy, Amit K. Jaiswal, Swarna Jaiswal

Articles

The increased environmental pollution has led to finding sustainable solutions for non-renewable plastic-based food packaging materials. Thus, the use of biomaterial-based packaging material has become an immense trend. This work aims at developing an antimicrobial biodegradable chitosan-alginate bio-nano composite film with TiO2 nanoparticle (NPs) for food packaging applications. The film was developed by a solution casting method. The chemical, mechanical, thermal, barrier, antimicrobial, and biodegradable properties of the packaging films were evaluated. Packaging studies were performed for 15 days for cherry tomatoes. The designed packaging material had enhanced the mechanical properties with a significantly (p < 0.05) higher tensile strength of 15.76 folds and 2 fold higher elongation at break. The UV barrier properties increased by 88.6%, while the film transparency decreased by 87.23%. Molecular interaction of N-H covalent bonds was observed between alginate and chitosan together with TiO2 NPs. The developed bio-nano composite film showed antimicrobial activity against foodborne pathogens E. coli, S. aureus, S. typhi, and L. monocytogene with a log reduction of 7.08, 7.28, 6.04 & 6.02 log CFU/ml respectively at 24 hours incubation period. The film was completely biodegraded and a weight loss of 89.06% was observed in bio-nanocomposite film during the 3 months. Shelf-life estimation of cherry tomato using developed packaging films showed an increase in the shelf-life up to 8 days with stable pH, total soluble solids, and weight with no bacterial growth when packaged with prepared film. Owing to their improved mechanical, UV barrier, antibacterial, and biodegradability, the prepared active bio-nano composite packaging films could be considered a potential candidate for fruit packaging.

Go to article

Analysis Of Hemp Fiber Reinforced Polylactide Composite Under High Strain-Rate, Benjamin Rhoads May 2022

Analysis Of Hemp Fiber Reinforced Polylactide Composite Under High Strain-Rate, Benjamin Rhoads

Honors Theses

The introduction of hemp fibers into a polylactide (PLA) matrix creates a hemp fiber-reinforced composite with 10% hemp fibers and 90% PLA. Natural fibers are becoming a popular alternative to synthetic fibers since they are environmentally friendly, and hemp-fibers are becoming used more often as the demand for natural fibers increased. A Split-Hopkinson Pressure Bar was used to test this composite against a control group using elastic wave propagation theory. Strain gauges were mounted on the incident and transmission bars of the SHPB to measure the propagation of the wave that caused the strain in the sample, which were used …

Go to article

Synthesis Of Aromatic Acetylene Alcohols Based On Benzaldehyde And Its Halogenated Products, Sanat Samatov, Abduvakhab Ikramov, Saida Abdurakhmanova, Odiljon Ziyadullayev, Guzal Otamukhamedova May 2022

Synthesis Of Aromatic Acetylene Alcohols Based On Benzaldehyde And Its Halogenated Products, Sanat Samatov, Abduvakhab Ikramov, Saida Abdurakhmanova, Odiljon Ziyadullayev, Guzal Otamukhamedova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this study is to synthesize the corresponding aromatic acetylenic alcohols by alkylation with phenylacetylene in a complex catalytic system based on Zn(OTf)2 and TBAF·3H2O for the first time with benzaldehyde and some of its halogen derivatives. The selectivity and stability of catalysts used for the yields of reactions for the synthesis of aromatic acetylene alcohols were analyzed. The effect of benzaldehyde and its halogenated derivatives on the product yield was analyzed. The nature, structure, isomerism, spatial structure and other properties influenced to this reactions were studied. Some features of reactions of synthesis of aromatic …

Go to article

Study Of Sorption Of Some Metal Ions By The Obtained Phosphoric Acid Cation Exchanger Of Polycondensation Type, Malika Berdieva, Rano Nazirova, Alisher Yuldashev, Umida Sharipova, Dilmurod Azimov May 2022

Study Of Sorption Of Some Metal Ions By The Obtained Phosphoric Acid Cation Exchanger Of Polycondensation Type, Malika Berdieva, Rano Nazirova, Alisher Yuldashev, Umida Sharipova, Dilmurod Azimov

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of this work is to investigate the sorption of Cu2+, Co2+, Ni2+, UO22+ ions, etc. depending on the ionic form of the cationite and the pH of the medium on phosphoric acid cationite obtained by forsforylation of a polymer based on cubic waste of the Shurtan gas-chemical complex and a secondary product of the hydrolysis industry – furfural. It was found that copper and UO22+ ions are best sorbed by cationite when the cationite is in Na form. The UO22+ ion is sorbed fairly well in …

Go to article

Thermal Properties Of Polyelectrolyte Complexes Of Bombyx Mori Chitosan With Collagen, Shuhrat Khudoyberdiev, Noira Vokhidova, Mukhitdin Abdurazakov, Sayora Rashidova May 2022

Thermal Properties Of Polyelectrolyte Complexes Of Bombyx Mori Chitosan With Collagen, Shuhrat Khudoyberdiev, Noira Vokhidova, Mukhitdin Abdurazakov, Sayora Rashidova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the work was to study the thermal behavior of the polyelectrolyte complexes of Bombyx mori ChS with collagen. As a result of the studies, the thermal properties of polyelectrolyte complexes based on Bombyx mori chitosan with collagen in wt. rel. 1:0,1 and 1:0,2 respectively. It has been determined that the most significant weight changes for chitosan with a molecular weight of 15×103 and the degree of deacetylation of 85% occur at a temperature is 270 °C, when the mass loss rate reaches its maximum value. For collagen, the same temperature is 277 °C. For complexes ChS/collagen …

Go to article

Electromechanical Fatigue Properties Of Dielectric Elastomer Stretch Sensors Under Orthopaedic Loading Conditions, Andrea Karen Persons May 2022

Electromechanical Fatigue Properties Of Dielectric Elastomer Stretch Sensors Under Orthopaedic Loading Conditions, Andrea Karen Persons

Theses and Dissertations

Fatigue testing of stretch sensors often focuses on high amplitude, low-cycle fatigue (LCF) behavior; however, when used for orthopaedic, athletic, or ergonomic assessments, stretch sensors are subjected to low amplitude, high-cycle fatigue (HCF) conditions. As an added layer of complexity, the fatigue testing of stretch sensors is not only focused on the life of the material comprising the sensor, but also on the reliability of the signal produced during the extension and relaxation of the sensor. Research into the development of a smart sock that can be used to measure the range of motion (ROM) of the ankle joint during …

Go to article

Insect Antennae As Bioinspirational Superstrong Fiber-Based Microfluidics, Griffin J. Donley May 2022

Insect Antennae As Bioinspirational Superstrong Fiber-Based Microfluidics, Griffin J. Donley

All Theses

Nature is frequently turned to for inspiration for the creation of new materials. Insect antennae are hollow, blood-filled fibers with complex shape, and are cantilevered at the head. The antenna is muscle-free, but the insect can controllably flex, twist, and maneuver it laterally. To explain this behavior, a comparative study of structural and tensile properties of the antennae of Periplaneta americana (American cockroach), Manduca sexta (Carolina hawkmoth), and Vanessa cardui (painted lady butterfly) was performed. These antennae demonstrate a range of distinguishable tensile properties, responding either as brittle fibers (Manduca sexta) or strain-adaptive fibers that stiffen when stretched (Vanessa cardui …

Go to article

Isolation And Production Of Tandem Collagen Binding Domain From Clostridial Collagenase Colg And Developments In C1q Reagent Production For Future Molecule Characterization Work, Stephanie Beitle May 2022

Isolation And Production Of Tandem Collagen Binding Domain From Clostridial Collagenase Colg And Developments In C1q Reagent Production For Future Molecule Characterization Work, Stephanie Beitle

Chemical Engineering Undergraduate Honors Theses

This thesis covers a two part project: the production methods to create a double collagen binding domain molecule with a growth factor for wound healing applications and the development of a new in-house production method for isolating C1q from bovine blood. The wound healing molecule was created using transformation, sonication, and purification before being tested via electrophoresis SDS page and Western blots to confirm the molecule’s presence. The C1q in-house production method utilizes an ultrafiltration flow cell rather than dialysis at a critical point in the process, allowing for researchers to not only be able to use a single small …

Go to article

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling May 2022

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

LSU New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Go to article

Synthesis And Phase Transition Characterization Of Liquid Crystal Membranes With Slit-Like Pores, Isaac Hopwood May 2022

Synthesis And Phase Transition Characterization Of Liquid Crystal Membranes With Slit-Like Pores, Isaac Hopwood

Chemical Engineering Undergraduate Honors Theses

Membranes with slit-like pores have been of interest for some time due to their ability to reject smaller particles than traditional cylindrical-pored membranes at the same fluid flux. However, using liquid crystals as a template for this sort of membrane has not been thoroughly investigated. In this study, the liquid crystal mixture of RM257 (2-Methyl-1,4-phenylene bis(4-(3-(acryloyloxy)propoxy)benzoate)) and 5CB (4-Cyano-4'-pentylbiphenyl) for the purpose of manufacturing membranes with slit-like pores, the phase transition behavior of this LC mixture at various mole fractions of RM257, and the impact of mole fraction of RM257 in the liquid crystal (LC) mixture and membrane manufacturing conditions …

Go to article

Investigating The Effect Of Polymer Hydrogels On The Antimicrobial Properties Of Activated Carbon Through The Utilization Of Bacterial, Viral, And Parasitic Microorganisms, Zoe Gunter May 2022

Investigating The Effect Of Polymer Hydrogels On The Antimicrobial Properties Of Activated Carbon Through The Utilization Of Bacterial, Viral, And Parasitic Microorganisms, Zoe Gunter

Honors Theses

Activated carbon (AC) has long been utilized in biomedical applications due to its innate antimicrobial characteristics. However, little is understood about the mechanism of action that allows AC to prohibit the propagation of different pathogen species. To further ascertain these characteristics and how they affect the propagation of pathogens, procedures were designed with bacterial, viral, and parasitic agents which were utilized in conjunction with varying concentrations of polymer hydrogels to examine the antimicrobial efficacy of AC. The studies performed for this thesis were conducted employing coconut-based AC and Noveon® AA-1 Polycarbophil USP or Carbopol® 974P NF hydrogels which, …

Go to article

Synthesis Of Monodisperse Nanoscintillators At High Temperatures For Biomedical Relevant Applications, Eric Zhang May 2022

Synthesis Of Monodisperse Nanoscintillators At High Temperatures For Biomedical Relevant Applications, Eric Zhang

All Dissertations

Luminescent sub-100 nm particulates continuously generate immense research interest in the biomedical field for imaging, theranostics, and optogenetics. Conventionally, upconversion nanoparticles or UV activated semiconductors are studied, however these materials are limited by biological barriers such as the skin which reduces the penetration depth of these excitation sources, tissue's auto- fluorescence, and toxicity. One approach to overcome these challenges is to use nanoscintillators (sub-100 nm materials that can generate visible light using high energy excitation sources such as x-rays) which can generate light locally to the human body. Numerous scintillators have been reported since the discovery of x-rays from the …

Go to article

Durability Of Non-Metallic Materials For Additively Manufactured Heat Spreader Fabrication, Rafael Estrella May 2022

Durability Of Non-Metallic Materials For Additively Manufactured Heat Spreader Fabrication, Rafael Estrella

Mechanical Engineering Undergraduate Honors Theses

Power electronics are necessary to convert power from DC sources for AC applications. As this technology trends toward smaller packaging for denser power loads, the increased electrical losses result in deleterious excess heat. Thermal management devices are required to prevent the effects of thermal runaway from shortening the longevity of these modules. Nonmetallic jet impingement heat spreaders provide several benefits in terms of weight and performance over conventional cold plates while not accentuating EMI from the switches in the power module; however, the polymer makeup of the materials previously used for fabricating these devices raises durability concerns under the high …

Go to article

Effects Of Sizing Agents On Mechanical Properties Of Carbon Fiber–Polymer Composites Via Fused Filament Fabrication Additive Manufacturing., Benjamin D. Mitchell May 2022

Effects Of Sizing Agents On Mechanical Properties Of Carbon Fiber–Polymer Composites Via Fused Filament Fabrication Additive Manufacturing., Benjamin D. Mitchell

Electronic Theses and Dissertations

This study demonstrated the effects of changing the sizing agent parameter during the preparation of carbon fibers on the mechanical properties of composite made with acrylonitrile butadiene styrene (ABS) as the matrix material and carbon fibers as the fiber material. Three types of sizing agents produced by Allnex were used to coat three different batches of carbon fibers that were mixed with a torque rheometer and extruded with a barrel-style melt extruder into continuous spools of 1.75 mm filament for use with commercial 3D printers. Tensile tests were conducted on the filaments and tensile bars printed from the materials. Results …

Go to article

Mechanochromic Tunable Emissions Of Hydrogel Encapsulated Radioluminescent Crystalline Colloidal Arrays, Sarah Mell May 2022

Mechanochromic Tunable Emissions Of Hydrogel Encapsulated Radioluminescent Crystalline Colloidal Arrays, Sarah Mell

All Theses

Crystalline colloidal arrays (CCAs) are periodic dielectric arrays composed of monodisperse, negatively charged nanoparticles with unique optical characteristics. Poly(styrene-co-propargyl acrylate) (PS-PA) based copolymer nanoparticles synthesized via an emulsion polymerization form the basis of the CCAs in this work. The negatively charged surfaces result in the colloidal nanoparticles self-assembling into a face-centered cubic (fcc) crystal-like structure. The long-range order and spatial periodicity of the array result in a rejection wavelength, characteristic of CCAs, in which a specific wavelength of light is forbidden from propagating throughout the optical system. The CCAs exhibit mechanochromism through a rejection wavelength shift corresponding to a change …

Go to article

Extractive Membranes For The Detection And Screening Of Waterborne Plutonium, James Foster May 2022

Extractive Membranes For The Detection And Screening Of Waterborne Plutonium, James Foster

All Dissertations

The development of rapid screening tools for special nuclear materials remains a crucial focus for nonproliferation efforts. Traditional approaches for the analysis of trace-level Pu isotopes in water requires tedious and time-consuming sample preparation steps that do not lend well to expeditious screening. Therefore, a novel analytical method that combines both Pu concentration and source preparation into a single detection system would make for an invaluable tool for nuclear security applications. Extractive membranes absorbers can help to fulfill this role as they are capable of concentrating Pu to detectable limits while subsequently serving as alpha spectrometry sample sources. In Chapter …

Go to article

First Prev Next Last