Materials Science and Engineering Commons^™

Anisotropy Of Exchange Stiffness And Its Effect On The Properties Of Magnets, K. D. Belashchenko

Kirill Belashchenko Publications

Using the spin-spiral formulation of the tight-binding linear muffin-tin orbital method, the principal components of the exchange stiffness tensor are calculated for typical hard magnets including tetragonal CoPt-type and hexagonal YCo₅ alloys. The exchange stiffness is strongly anisotropic in all studied alloys. This anisotropy makes the domain wall surface tension anisotropic. Competition between this anisotropic surface tension and magnetostatic energy controls the formation and dynamics of nanoscale domain structures in hard magnets. Anisotropic domain wall bending is described in detail from the general point of view and with application to cellular Sm–Co magnets. It is shown that the repulsive …

Optical Characterization And Modeling Of Compositionally Matched Indium Arsenide-Antimonide Bulk And Multiple Quantum Well Semiconductors, Scott C. Phillips

Theses and Dissertations

Indium arsenide-antimonide (InAsSb) semiconductors have been determined to emit in the 3-5 micrometer range, the window of interest for countermeasures against infrared electro-optical threats. This experiment set out to cross the bulk to quantum well characterization barrier by optically characterizing two sets of compositionally matched type I quantum well and bulk well material samples. Absorption measurements determined the band gap energy of the bulk samples and the first allowed subband transition for the quantum wells. By collecting absorption spectra at different temperatures, the trend of the energy transitions was described by fitting a Varshni equation to them. The expected result …

Mapping Surface Polarization In Thin Films Of The Ferroelectric Polymer P(Vdf-Trfe)., Bradley W. Peterson, Stephen Ducharme, Vladimir M. Fridkin, Timothy J. Reece

Stephen Ducharme Publications

Pyroelectric Scanning Microscopy (PSM) has been developed to enable mapping of surface polarization in ferroelectric thin films, in particular the copolymer polyvinylidene fluoride trifluororethylene, or P(VDF-TrFE). The Chynoweth method for dynamically measuring pyroelectric current is employed in conjunction with a micropositioning system to construct two-dimensional images of the film polarization. These images have revealed enhancement of the polarization near the edges of the film below the average coercive field, with the center's polarization increasing thereafter to meet the edge value at saturation.

Electron Irradiation Effects On Ferroelectric Copolymer Langmuir-Blodgett Films, Christina M. Othon, Stephen Ducharme

Stephen Ducharme Publications

The effect of irradiation on the ferroelectric properties of Langmuir-Blodgett films of the copolymer poly(vinylidene fluoride-trifluorethelene) is investigating using 1.26 MeV electrons with dosages from 16 to 110 Mrad. Irradiation causes a systematic decrease in the phase transition temperature, coercive field and polarization of these thin films.

Ferroelectricity At Molecular Level, L. M. Blinov, A. V. Bune, Peter A. Dowben, Stephen Ducharme, Vladimir M. Fridkin, S. P. Palto, K. A. Verkhovskaya, G. V. Vizdrik, S. G. Yudin

Stephen Ducharme Publications

he synthesis of ultrathin ferroelectric nanostructures by the Langmuir-Blodgett method and their properties are reviewed. It is shown that ferroelectricity exists in one monolayer of the ferroelectric P(VDF-TrFE) copolymer, i.e., at the molecular level. The specific characteristics of switching of ultrathin ferroelectric films are established.

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

There is an active international interest in lead-bismuth eutectic and similar liquid lead systems because of the relevance to the transmutation of nuclear waste, fast reactors, and spallation neutron sources. A successful program in nuclear waste processing that includes transmutation in accelerator-driven systems and fast reactors, would significantly decrease the space requirements for geological repositories.

Materials in these systems must be able to tolerate high neutron fluxes, high temperatures, and chemical corrosion. For lead bismuth eutectic (LBE) systems, there is an additional challenge because the corrosive behaviors of materials in LBE are not well understood. Most of the available information …

Stress Corrosion Cracking Of Target Material, Mohammad K. Hossain

Transmutation Sciences Materials (TRP)

The primary objective of this paper is to evaluate the effect of hydrogen on environment assisted cracking of candidate target materials for transmutation applications. Transmutation refers to transformation of long-lived actinides and fission products from spent nuclear fuels (SNF), and occurs when the nucleus of an atom changes because of natural radioactive decay, nuclear fission, nuclear fusion, neutron capture, or other related processes. Martensitic Alloy EP 823 was selected to be the candidate alloy for this investigation. During the initial phase, the stress corrosion cracking (SCC) behavior of this alloy was evaluated in neutral (pH: 6-7) and acidic (pH: 2-3) …

Identification Of Dynamic Properties Of Materials For The Nuclear Waste Package, Brendan O'Toole, Mohamed Trabia, Amy J. Smiecinski

Publications (YM)

Stainless steel 316L, titanium alloy grade 7, and alloy C22 are currently under consideration as candidate materials for use in various components associated with the spent nuclear fuel package, which must be designed to withstand structural deformation caused by static, thermal, and handling loads. In addition, it has to maintain its integrity in case of accidents, where it may be subjected to high loads over a very short period of time. Mechanical characteristics of these three materials under dynamic loading are not well documented. This paper describes the procedures and results obtained from experiments performed over a range of slow …

Task 32 Delayed Hydride Cracking Of Spent Fuel Cladding Under Repository Conditions, Ajit K. Roy, Anthony Hechanova, Amy J. Smiecinski

Publications (YM)

The objective of this quality-affecting task is to evaluate the susceptibility of spent nuclear fuel cladding materials (zirconium alloys) to stress corrosion cracking (SCC), delayed hydride cracking (DHC) and localized corrosion (pitting/crevice) in simulated repository environments. During the first year of this project, major efforts were focused on developing the infrastructure for performing the desired testing involving two highly corrosion-resistant alloys namely, zircaloy-2 (Zr-2) and zircaloy-4 (Zr-4) in simulated concentrated acidic water (SAW) and modified SAW (SAWM). Modification of the SAW chemistry was done by adding hydrochloric acid (HC1) to achieve lower pH. The construction of the "Materials Performance Laboratory …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 5/16/03- 8/15/03, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

The analysis of mold filling and solidification continues with progress being made for the consideration of these two features within one model. Analysis of the induction heating process of an Induction Skull Melter (ISM) is under study. Efforts are underway to validate the modeling procedure and specific comparisons are being made to previously published work. Few detailed modeling results have been reported by other researchers, making the validations an important part of the overall modeling process. Skin heating depths, power deposition rates, and other process parameters are being evaluated for use in upcoming furnace design simulations. Efforts are beginning on …

45th Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 45th annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-endorsed by the Colorado Section of the American Chemical Society and the Rocky Mountain Section of the Society for Applied Spectroscopy. Held in Denver, Colorado, July 27-31, 2003.

Comment On: 'Depolarization Corrections To The Coercive Field In Thin-Film Ferroelectrics', Stephen Ducharme, Vladimir Fridkin

Stephen Ducharme Publications

The Letter by Dawber et al. [J. Phys.: Condens. Matter 15 L393 (2003)] notes that incomplete screening in the electrodes of a ferroelectric capacitor can result in an underestimate for the true coercive field in films of nanometer thickness. We show that their estimate of the magnitude of this correction it too large in the case of ferroelectric copolymer Langmuir- Blodgett films and, as a result, invalidates the claim that finite-size scaling of the ferroelectric coercive field is evident in films thinner than 15 nm.

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 2/16/03- 5/15/03, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

Progress continues on the analysis of casting and solidification of the melt into molds. Modeling results for constant pressure casting, which is more realistic, have been obtained and produce physically realistic results for flow that starts, flows, and then eventually stops as it enters the mold. Potential mass transfer modeling features (Lammuir’s law for example) are being studied to enhance the capabilities of a mass transfer in a detailed system model. Different parameters are being varied as part of a parametric study to evaluate factors that impact the flow of the melt into the molds. The ability to include the …

Dynamics Of Phase Transitions On Low-Index Metal Surfaces, Bo Lin

Electrical & Computer Engineering Theses & Dissertations

The surface superheating and phase transitions at the low-index surface of metal were investigated using conventional continuous and 100-ps time-resolved reflection high-energy electron diffraction. Three metal surfaces, In(111), Au(110) and Pb(111), have been investigated in this work. The high temperature behavior of the In(111) surface was investigated using reflection high-energy electron diffraction with 100-ps temporal resolution. The change of surface vacancy density on In(111) is observed from 300 K to near the bulk melting point. The vacancy-formation energy of In(111) surface is estimated from experimental results. The surface vacancy density is observed to increase with temperature; however, the average random …

Field Emission Based Sensors Using Carbon Nanotubes, Changkun Dong

Physics Theses & Dissertations

A number of sensitive applications would be greatly benefited by the development of better cold cathodes that employ the electron field emission process. Among the many kinds of field emitters that could be tried, carbon nanotubes (CNT) have a number of distinct advantages because of their unique geometrical structure, chemical inertness, mechanical stiffness, and high thermal and electrical conductivities. This dissertation describes research in which CNT cathodes were fabricated and their emission characteristics were measured.

Multi-walled carbon nanotubes (MWNT) were grown by chemical vapor deposition (CVD) on various substrates: Ni and Hastelloy gauze, 304 stainless steel (SS) plates, and Ni-coated …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to insure that their knowledge and experience benefits the project. The research to be conducted during year three will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this third year is to …

Experimental Investigation Of Steel Corrosion In Lead Bismuth Eutectic (Lbe): Characterization, Species Identification, And Chemical Reactions, John Farley, Dale L. Perry, Allen L. Johnson

Transmutation Sciences Materials (TRP)

The goal of the present research is to achieve a basic understanding of corrosion of steels by Lead Bismuth Eutectic (LBE). Liquid LBE is under consideration in the transmuter as both a spallation target and as a blanket coolant. There have been previous studies of LBE, especially by the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The Russians found that the presence of small amounts (ppm) of oxygen in the LBE significantly reduced corrosion. However, a fundamental understanding and verification of its role in the corrosion of steels is still very incomplete. …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report November- December 2002 January 2003, John Farley

Transmutation Sciences Materials (TRP)

We continue to get valuable data from sputter depth profiling of steel samples. We meet weekly to discuss progress. We took depth-profiling data on D9 steel that had been exposed to LBE. This the first time we have examined this type of steel. This is important because it will enable us to separate out two effects and determine their effect on corrosion: composition of the steel vs surface preparation.

We started to plan a small experiments using a crucible of heated LBE, with the research program to be conducted at UNLV, on basic aspects of corrosion in this system. The …

Ultrafine Nife2o4 Powder Fabricated From Reverse Microemulsion Process, Jiye Fang, Narayan Shama, Le Duc Tung, Eun Young Shin, Charles J. O'Connor, Kevin L. Stokes, Gabriel Caruntu, John B. Wiley, Leonard Spinu, Jinke Tang

Physics Faculty Publications

NiFe2O4 ultrafine powder with high crystallinity has been prepared through a reverse microemulsion route. The composition in starting solution was optimized, and the resulting NiFe2O4 was formed at temperature of around 550–600 °C, which is much lower than that observed from the solid-state reaction. Magnetic investigation indicates that samples are soft-magnetic materials with low coercivity and with the saturation magnetization close to the bulk value of Ni ferrite.

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Materials for transmuter systems must be able to tolerate high neutron fluxes, great temperatures, and chemical corrosion. For lead bismuth eutectic (LBE) systems, there is an additional challenge in that the corrosive behaviors of materials in LBE are not well understood. Most of the available information on LBE systems has come from the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The Russians found that the presence of small amounts of oxygen (on the order of parts per million) in the LBE significantly reduced corrosion. However, a fundamental understanding and verification of its …

Surface Studies Of Corrosion Of Stainless Steel By Lead Bismuth Eutectic, Daniel Koury, Brian D. Hosterman, John Farley, Dale L. Perry, D. Parsons, J. Manzerova, Allen L. Johnson

Transmutation Sciences Materials (TRP)

Why is Lead Bismuth Eutectic Important?

• Changing national security stances have led to reexamination of nuclear waste reprocessing

• Dangerous actinides can be separated and

• Transmuted into safer products, creating a waste form dangerous for only hundreds of years, in addition to the production (up to 1/3 of the original fission energy) of useful energy

• Non-moderating coolants or spallation targets for production of fast neutrons is required for transmutation

• Russian experience with LBE coolants in their nuclear submarine fleet makes LBE an attractive possible transmutation coolant technology

• Corrosion of steel by LBE is an important …

Investigation Of The Corrosion Of Steel By Lead-Bismuth Eutectic (Lbe) Using Scanning Electron Microscopy And X-Ray Photoelectron Spectroscopy, Daniel Koury

UNLV Theses, Dissertations, Professional Papers, and Capstones

Lead Bismuth Eutectic (LBE) has been proposed for use in programs for accelerator transmutation of waste. LBE is the leading candidate material as a spallation target and an option for the sub-critical blanket coolant. The corrosion of 316 and 316L stainless steels by LBE has been studied using UNLV's facilities for Scanning Electron Microscopy (SEM) and X-ray Photoelectron Spectroscopy (XPS). We have compared exposed and unexposed samples and studied the differences. Some amount of surface contamination is present on the samples and has been removed by ionbeam etching. The unexposed samples reveal typical stainless steel characteristics: a chromium oxide passivation …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report August September October 2002, John Farley

Transmutation Sciences Materials (TRP)

We continued with sputter depth profiling of 316 and 316L steel samples that have been exposed to LBE. We also calibrated the sputter depth profiling using a sample of SiO₂ on Si, and the SEM. This is a valuable independent determination of the thickness of oxide layers.

In the laboratory, progress continues using the XPS machine. Experiments have been performed on steel samples using Argon ions to mill away the surface of the sample, thereby making measurements as a function of depth. This "ion beam milling" proceeds slowly through the oxide layer that covers the steel sample. We are …

Dielectric Properties Of A Ferroelectric Copolymer Langmuir–Blodgett Film, Mahantappa S. Jogad, Stephen Ducharme

Stephen Ducharme Publications

We report measurements of the real (epsilon prime) and imaginary (epsilon double-prime) parts of the relative complex permittivity of a Langmuir–Blodgett film of ferroelectric copolymer of vinylidene fluoride (70%) with trifluoroethylene (30%). The measurements were made in the temperature range of 35 to 125° C, and frequency range of 19 Hz to 5 MHz. The results indicate low frequency loss due to conduction and dielectric loss peak near the ferroelectric–paraelectric phase transition.

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 5/16/02- 8/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

An important aspect of the Advanced Accelerator Applications (AAA) program is the development of a casting process by which volatile actinide element (i.e., americium) can be incorporated into metallic alloy fuel pins. The traditional metal fuel casting process uses an inductively heated crucible.

This process works well for the fabrication of metal fuel pins traditionally composed of alloys of uranium and plutonium, but does not work well when highly volatile actinides are included in the melt. The problem occurs both during the extended time period required to superheat the alloy melt as well as when the chamber must be evacuated. …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report For May-June-July 2002, John Farley

Transmutation Sciences Materials (TRP)

The goal of this project is to understand the basic science of corrosion in the steel/LBE system.

We are taking more data, typically using the newly installed X-ray Photoelectron Spectrometry (XPS) apparatus, and analyzing our existing data. Undergraduate students Denise Parsons and Julia Manzerova have helped a great deal in the analysis of the data. We can obtain the elemental composition as a function of position within the sample. This gives clues to the migration of materials, the composition of the protective oxide layer, and the basic science of the corrosion process. We found dramatic differences between the exposed and …

44th Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 44th annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-endorsed by the Colorado Section of the American Chemical Society and the Society for Applied Spectroscopy. Held in Denver, Colorado, July 28 - August 1, 2002.

Magnetic And Mössbauer Studies On Oxygen Deficient Perovskite, La₀.₆Sr₀.₄Feo3-Δ, Jinbo Yang, William B. Yelon, William Joseph James, X.-D. Zhou, Yixiang Xie, Harlan U. Anderson, Zili Chu

Physics Faculty Research & Creative Works

Samples of La_0.6Sr_0.4Fe_3-δ with varying oxygen vacancy contents were prepared by heating them in different gas flows. Magnetization measurement showed that samples with low oxygen vacancies have a magnetic ordering temperature in the range of 300-325 K while those with 9%-12% oxygen vacancies have a magnetic ordering temperature of 800 K and higher. Mössbauer spectra at 300 K exhibit paramagnetic or weak magnetic characteristics for the N₂, O₂, and air-quenched samples, whereas an average hyperfine field of 52 T is found for the CO/CO₂ reduced samples. The heat treatment in …

Humidity And Temperature Boundaries For Biofilm Formation In Yucca Mountain, Terry Ann Else, Penny S. Amy, James Jay, Amy J. Smiecinski

Publications (YM)

To determine the long-term success of the recommended Yucca Mountain high-level nuclear waste repository, studies of bacterial colonization and biofilm development are needed. Bacteria involved in microbially-influenced corrosion and degradation are known to form biofilms with the potential to impact the integrity of repository packaging and structural materials. Temperature and humidity are environmental factors that can greatly affect biofilm formation. Therefore, it is necessary to determine the temperature and humidity conditions that affect biofilm formation. Microcosms, which simulated the repository environment of Yucca Mountain, were placed at temperatures ranging from 30° C to 70° C and in relative humidities ranging …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to ensure that their knowledge and experience benefits the project. The research to be conducted during the second year will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this second year is …