Materials Science and Engineering Commons^™

Etching With Electron Beam Generated Plasmas, D. Leonhardt, Scott G. Walton, Christopher Muratore, Richard F. Fernsler, R. A. Meger

Chemical and Materials Engineering Faculty Publications

A modulated electron beam generated plasma has been used to dry etch standard photoresist materials and silicon. Oxygen–argon mixtures were used to etch organic resist material and sulfur hexafluoride mixed with argon or oxygen was used for the silicon etching. Etch rates and anisotropy were determined with respect to gas compositions, incident ion energy (from an applied rf bias) and plasma duty factor. For 1818 negative resist and i-line resists the removal rate increased nearly linearly with ion energy (up to 220 nm/min at 100 eV), with reasonable anisotropic pattern transfer above 50 eV. Little change in etch rate was …

Exploration Of Artificial Multiferroic Thin-Film Heterostructures Using Composition Spreads, K.-S. Chang, M. A. Aronova, C.-L. Lin, M. Murakami, M.-H. Yu, Jason R. Hattrick-Simpers, O. O. Famodu, S. Y. Lee, R. Ramesh, M. Wuttig, I. Takeuchi, C. Gao, L. A. Bendersky

Faculty Publications

We have fabricated a series of composition spreads consisting of ferroelectric BaTiO₃ and piezomagnetic CoFe₂O₄ layers of varying thicknesses modulated at nanometer level in order to explore artificial magnetoelectricthin-film heterostructures. Scanning microwavemicroscopy and scanning superconducting quantum interference device microscopy were used to map the dielectric and magnetic properties as a function of continuously changing average composition across the spreads, respectively. Compositions in the middle of the spreads were found to exhibit ferromagnetism while displaying a dielectric constant as high as ≈120.

Effect Of Plasma Flux Composition On The Nitriding Rate Of Stainless Steel, Christopher Muratore, Scott G. Walton, D. Leonhardt, Richard F. Fernsler, David D. Blackwell, R. A. Meger

Chemical and Materials Engineering Faculty Publications

The total ion flux and nitriding rate for stainless steel specimens exposed to a modulated electron beam generated argon-nitrogen plasma were measured as a function of distance from the electron beam axis. The total ion flux decreased linearly with distance, but the nitriding rate increased under certain conditions, contrary to other ion flux/nitriding rate comparisons published in the literature. Variation in ion flux composition with distance was explored with a mass spectrometer and energy analyzer as a possible explanation for the anomalous nitriding rate response to ion flux magnitude. A transition in ion flux composition from mostly N2 1 to …

Preparation Of Magnetic Nanoparticles And Their Assemblies Using A New Fe(Ii) Alkoxide Precursor, Suresh Pillai, Grainne Biddlecombe, Yurii Gun’Ko, John Kelly, J. Michael Coey, Alexis Douvalis

Articles

No abstract provided.

Characterization Of Lithium Intercalation Oxides Based On Manganese And Copper, Vengidason Seguprakash

Student Works (2000-2009)

In this study, several lithium intercalation compounds have been synthesized and characterized. Lithium manganese copper oxide cathode materials were prepared by sol gel method using tartaric acid as the gelating agent. Five types of cathode materials were synthesized. The sol gel technique has permitted the synthesis of manganese oxides that are capable of reversibly intercalating large amounts of lithium ions. To see the effect of adding copper to lithium manganese oxide several experiments were carried out. These include X-Ray diffraction to see whether the LiMn₂O₄ lattice has widened or collapsed. It was seen that LiMn₂O₄ and LiCu₂O₂ XRD patterns were …

Kinetics Of Laser Chemical Vapor Deposition Of Carbon And Refractory Metals, Feng Gao

Doctoral Dissertations

Three-dimensional laser chemical vapor deposition (3D-LCVD) has been used to grow rods of carbon, tungsten, titanium, and hafnium from a variety of hydrocarbons and metal halide-based precursors. A novel computerized 3D-LCVD system was designed and successfully used in the experiments. A focused Nd:Yag laser beam (λ = 1.06 μm) was utilized to locally heat up a substrate to deposition temperature. The rods, which grew along the axis of the laser beam, had a typical diameter of 30–80 μm and a length of about 1 mm. The precursors for carbon deposition were the alkynes: propyne, butyne, pentyne, hexyne, and octyne. Propyne …

Development Of A Curved Layer Lom Process For Monolithic Ceramics And Ceramic Matrix Composites, Donald A. Klosterman, Richard P. Chartoff, Nora R. Osborne, George A. Graves, Allan Lightman, Gyoowan Han, Akos Bezewredi, Stan Rodrigues, Sung Pak, Gary Kalmanovich, Leon Dodin, Song Tu

Chemical and Materials Engineering Faculty Publications

A novel rapid prototyping technology incorporating a curved layer building style was developed. The new process, based on Laminated Object Manufacturing (LOM), was designed for efficient fabrication of curved layer structures made from ceramics and fiber reinforced composites. A new LOM machine was created, referred to as Curved Layer LOM. This new machine uses ceramic tapes and fiber prepregs as feedstocks and fabricates curved structures on a curved-layer by curved-layer basis. The output of the process is a three dimensional "green" ceramic that is capable of being processed to a seamless, fully dense ceramic using traditional techniques. A detailed description …

Cracking In Cycloaliphatic Epoxy/Aluminum Composite Electrical Bushings, Keith Alan Parker

Doctoral Dissertations

The problem of cracking in electrical apparatus bushings as a result of thermal stresses was investigated. The bushings were composed of cycloaliphatic epoxy insulators with embedded aluminum conductors. The problem is due to the difference in coefficients of thermal expansion of the two materials. A solution to the problem had been to coat the conductors before they were formed together with the epoxy insulators. The coating was assumed to prevent cracking by allowing movement between the two materials as their dimensions changed during thermal expansion and contraction. The contribution of the coating was to be established.

The hypothesis was that …

Derivation Of An Analytical Model To Calculate Junction Depth In Hgcdte Photodiodes, Stacy H. Gleixner, H. G. Robinson, C. R. Helms

Faculty Publications

Presents an enhanced analytical model to calculate junction depth and Hg interstitial profile during n-on-p junction formation in HgCdTe photodiodes. Detailed information on the enhanced model; Function of the model; Information on HgCdTe; Detailed information on how the model was obtained.

Recovery Of Scrap Tire Rubber Waste, Dalia Adel Habib Nakhla

Archived Theses and Dissertations

No abstract provided.

A Stochastic Model For Crystal-Amorphous Transition In Low Temperature Molecular Beam Epitaxial Si(111), R. Venkatasubramanian, Suresh Gorantla, S. Muthuvenkatraman, Donald L. Dorsey

Electrical & Computer Engineering Faculty Research

Molecular beam epitaxial Si (111) grown below a certain temperature result in amorphous structure due to the limited surface mobility of atoms in finding correct epitaxial sites. In spite of many experimental and theoretical studies, the mechanism of crystal‐amorphous transition and its dynamics related to the growth conditions are not well understood. In this article, we present a theoretical model based on the formation of stacking fault like defects as a precursor to the amorphous transition of the layer. The model is simulated based on a stochastic model approach and the results are compared to that of experiments for temperatures …

Comparison Of Time-Domain Reflectometry Performance Factors For Several Dielectric Geometries: Theory And Experiments, S. V. Maheshwarla, R. Venkatasubramanian, Robert F. Boehm

Electrical & Computer Engineering Faculty Research

We propose three nontraditional dielectric geometries and present an experimental and theoretical analysis and comparison of time domain reflectometry (TDR) performances for them. The traditional geometry (the probes inserted in material of essentially infinite extent) is compared to three nontraditional geometries where the probes are affixed outside of a core sample, inside of a bore, or flat on the surface of a semi-infinite solid. Our derivation relates the velocity of electromagnetic wave propagation to the complex permittivities and permeabilities of the media and the geometry for the three nontraditional configurations. Experimental results for air, styrofoam, dry sand, wet sand of …

Measurement Of The Coefficient Of Thermal Expansion Of Superconducting Thin Films Using Powder X-Ray Diffraction, Biju Chandran, R. Calvin Goforth, S. Nasrazadani

Journal of the Arkansas Academy of Science

The High Density Electronics Center (HiDEC) at the University of Arkansas, Fayetteville is developing the technology for High Temperature Superconductor Multi-Chip Modules (HTSC-MCM's). As part of this work, we are looking at the mechanical properties of HTSC materials. An important mechanical property which influences the mechanical integrity of the hybrid MCMis the coefficient of thermal expansion (CTE) of the HTSC films. As a first step in developing a procedure for the determination of the CTE of HTSC materials, the lattice parameters and the CTE of an alpha-alumina substrate have been determined by powder x-ray diffraction technique. An extension of this …

Using Living Materials To Intervene In The Natural Succession Process To Accelerate The Re-Development Of A Self-Sustaining Ecosystem That Has Been Damaged By Human Intervention, Eric Jorgensen

Materials Engineering

No abstract provided.

The Effect Of Thermal History On Modes Of Formation Of Borate Glasses Containing Titanium, Shahinaz Abd El Rahman Imam

Archived Theses and Dissertations

No abstract provided.

X-Ray Diffraction Studies Of Amorphous Silicon, Adel Gabra I Gouda

Archived Theses and Dissertations

No abstract provided.

Effects Of Oxygen Content Of Admitted Gases In Sulfide Flotation, Brian J. Boyle

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Methods Of Studying The Effects Of Frothers, Frank L. Bazzanella

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

A Study Of The Structure And Some Physical Properties Of Antimony Glasses, Pakinam Mahmoud Askalani

Archived Theses and Dissertations

No abstract provided.

Studies In Modulation Of Interfacial Reactions For Certain Sulphide Minerals, Robert Owen Beyaert

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Habit Modification Of Naclo3 With Nai, William A. Coghlan

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Production Of Standard-Grade Ferromanganese In An Electric Arc Furnace, Force F. Baney Jr.

Bachelors Theses and Reports, 1928 - 1970

The investigations conducted in this project were essentially concerned with the effects of various compositions of two different slag systems upon the increased recovery of manganese in a standard-grade ferromanganese.

Investigation Of The Ternary System Silver-Aluminum-Indium (Ag-Al-In), Elvin H. Beardslee

Bachelors Theses and Reports, 1928 - 1970

This thesis paper contains material pertaining to & preliminary investigation of the ternary system Ag-Al-In. Procedures in this preliminary investigation are discussed in detail.

Preliminary Examination Of The Aluminum Corner Of The Ternary System Aluminum-Silver-Indium (A1-Ag-In), Jerome J. Blake

Bachelors Theses and Reports, 1928 - 1970

In this paper the author attempts to lay the groundwork for future work on the Al-Ag-In system.

Increased Corrosion Of A 304 Stainless Steel Upon Bending, William C. Tiddy

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Identification Of Nonmetallic Inclusions In Armco Ingot Iron With Polarized Light, Frank E. Panisko

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

The Hydrometallurgy Of Uranium, John E. Cesarani

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Crystal Habit Modification Of Sodium Chlorate, Michael R. Keegan

Bachelors Theses and Reports, 1928 - 1970

All single crystals have a particular habit or morphology. The crystal habit refers to the relative degree of development of crystallographic planes into surfaces which make up the external appearance of the single crystal.

In this paper, NaClO3 is used as a parent crystal. Its simple cubic habit is modified to tetrahedral by the use of impurities of SO4=, S2O3=, Cr2O7=, and NO3-. The degree of habit change is studied as a function of impurity concentration and temperature. The problem and phenomena are explained in terms of surface chemistry and thermodynamics.

Physico-Chemical Principles Of Sixteenth Century Metallurgy, Robert E. Johnson

Bachelors Theses and Reports, 1928 - 1970

Following a review of sixteenth century metallurgical literature and a discussion of Gibbs free energy, this thesis discusses thermodynamic considerations of galena (PbS) reduction by iron from a lead assay of this period. The importance of fluxes in this assay is emphasized. The discussion covers both equilibrium and non-equilibrium conditions at 1100 degrees Celsius. Possible substitutes for iron are also covered.

Information from twenty-one small controlled lead assays is correlated with the thermodynamic discussion to determine the purpose of each constituent in the assay.

The Beneficiation Of Titaniferous-Magnetite Sands, Ronald Lloyd Nordwick

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation of beneficiation methods is to develop and study possible economic methods for recovering an iron-titanium concentrate of sufficient purity to meet metallurgical requirements for subsequent direct reduction to pig iron and a high titanium slag.