Materials Science and Engineering Commons^™

Exploring The Variability In The Gray Scale Imaging Process Of Asphalt Samples, David Oluwawade Olatunji

Civil Engineering Undergraduate Honors Theses

Gray scale image analysis is a powerful tool for testing asphalt concrete materials. From material composition to surface properties, gray scale analysis has shown evidence as a non-invasive way to obtain information from asphalt samples. Casillas et al. used a gray scale analysis to measure the Representative Volume Element of three asphalt sample geometries to understand the minimum size at which an asphalt sample is representative of a larger homogeneous mixture [1]. While the gray scale analysis used in this experiment yielded results, there were unknown factors in the image capturing process. Particularly, not much was known about the effect …

Parametric Analysis Of Particle Spreading With Discrete Element Method, Yuxuan Wu

Doctoral Dissertations and Master's Theses

The spreading of metallic powder on the printing platform is vital in most additive manufacturing methods, including direct laser sintering. Several processing parameters such as particle size, inter-particle friction, blade speed, and blade gap size affect the spreading process and, therefore, the final product quality. The objective of this study is to parametrically analyze the particle flow behavior and the effect of the aforementioned parameters on the spreading process using the discrete element method (DEM). To effectively address the vast parameter space within computational constraints, novel parameter sweep algorithms based on low discrepancy sequence (LDS) are utilized in conjunction with …

Kinetic Monte Carlo Investigations Involving Atomic Layer Deposition Of Metal-Oxide Thinfilms, David Tyler Magness

Graduate Theses/Dissertations

Atomic Layer Deposition is a method of manufacturing thin film materials. Metal-oxides such as zinc-oxide and aluminum-oxide are particularly interesting candidates for use in microelectronic devices such as tunnel junction barriers, transistors, Schottky diodes, and more. By adopting a 3D Kinetic Monte Carlo model capable of simulating ZnO deposition, the effect of parameters including deposition temperature, chamber pressure, and composition of the initial substrate at the beginning of deposition can be investigated. This code generates two random numbers: One is used to select a chemical reaction to occur from a list of all possible reactions and the second is used …

Proximity-Induced Magnetization In Graphene: Towards Efficient Spin Gating, Mihovil Bosnar, Ivor Lončarić, P. Lazić, Kirill Belashchenko, Igor Žutić

Kirill Belashchenko Publications

Gate-tunable spin-dependent properties could be induced in graphene at room temperature through the magnetic proximity effect by placing it in contact with a metallic ferromagnet. Because strong chemical bonding with the metallic substrate makes gating ineffective, an intervening passivation layer is needed. Previously considered passivation layers result in a large shift of the Dirac point away from the Fermi level, so that unrealistically large gate fields are required to tune the spin polarization in graphene (Gr). We show that a monolayer of Au or Pt used as the passivation layer between Co and graphene brings the Dirac point closer to …

New Metal Based Saturable Absorber For Ultrashort Pulse Generation, Muhammad Taufiq Ahmad

Student Works (2020-2029)

Cost-efficient, robust and flexible laser systems are vital for a wide-range of applications ranging from high-precision material processing to biomedicine. This thesis aims to explore pure silver and gold based saturable absorbers (SAs) as Q-switcher and mode-locker in various fibre laser cavities. The generations of Q-switched pulses in 1-,1.55-, and 2-micron regions have been successfully demonstrated using a pure gold, which was deposited using electron beam deposition onto a PVA thin-film as SA. For instance, a stable Q-switched thulium-doped fibre laser (TDFL) operating at 1949 nm was successfully demonstrated with the gold SA. The proposed laser generates Q switched pulses …

Prefilling Mylar Capacitor Edge Margins To Improve Capacitor Reliability And Size, Chase Kayser

Mechanical Engineering ETDs

Typical high-voltage, wound film-foil capacitors have large edge margins filled with air to prevent breakdown between foil electrodes. This arrangement is inefficient for energy density and leaves a volume where particulates may settle in an uncontrolled atmosphere. The reliability and size of high-voltage, wound film-foil capacitors could be improved by adding a material with higher breakdown strength into the edge margins. This will not only improve reliability and size but also act as a barrier to prevent foreign object debris (FOD), volatile organic compounds (VOCs), and water from damaging the capacitor’s performance. This paper will discuss the process of determining …

Detection Of Uncompensated Magnetization At The Interface Of An Epitaxial Antiferromagnetic Insulator, Pavel N. Lapa, Min Han Lee, Igor V. Roshchin, Kirill Belashchenko, Ivan K. Schuller

Kirill Belashchenko Publications

We have probed directly the temperature and magnetic field dependence of pinned uncompensated magnetization at the interface of antiferromagnetic FeF₂ with Cu, using FeF₂-Cu-Co spin valves. Electrons polarized by the Co layer are scattered by the pinned uncompensated moments at the FeF₂-Cu interface giving rise to giant magnetoresistance. We determined the direction and magnitude of the pinned uncompensated magnetization at different magnetic fields and temperatures using the angular dependencies of resistance. The strong FeF₂ anisotropy pins the uncompensated magnetization along the easy axis independent of the cooling field orientation. Most interestingly, magnetic fields as …

Reinvestigation Of The Intrinsic Magnetic Properties Of (Fe1-Xcox)2b Alloys And Crystallization Behavior Of Ribbons, Tej Nath Lamichhane, Olena Palasyuk, Vladimir P. Antropov, Ivan A. Zhuravlev, Kirill Belashchenko, Ikenna C. Nlebedim, Kevin W. Dennis, Anton Jesche, Matthew J. Kramer, Sergey L. Bud'ko, R. William Mccallum, Paul C. Canfield, Valentin Taufour

Kirill Belashchenko Publications

New determination of the magnetic anisotropy from single crystals of (Fe_1-xCo_x)2B alloys are presented. The anomalous temperature dependence of the anisotropy constant is discussed using the standard Callen-Callen theory, which is shown to be insufficient to explain the experimental results. A more material specific study using first-principles calculations with disordered moments approach gives a much more consistent interpretation of the experimental data. Since the intrinsic properties of the alloys with x=0.3-0.35 are promising for permanent magnets applications, initial investigation of the extrinsic properties are described, in particular the crystallization of melt spun ribbons with Cu, Al, …

Dynamic Analysis Of Viscoelastic Circular Diaphragm Of A Mems Capacitive Pressure Sensor Using Modified Differential Transformation Method, Dr Olurotimi A. Adeleye, Muritala Yusuf, Oluwaseyi .. Balogun

Karbala International Journal of Modern Science

In this paper, a dynamic analysis of the viscoelastic circular diaphragm of a Micro-Electro-Mechanical System (MEMS) capacitive pressure sensor using the Modified Differential Transformation Method (MDTM) is presented. The MEMS technology has been increasingly used to fabricate sensors and actuators and the MEMS capacitive pressure sensor is emerging in many high-performance applications. The deflection of these sensors diaphragm (plate) depends largely on the material of the diaphragm. In this study, a circular diaphragm of viscoelastic material is modeled using the classical plate theory. The governing differential equation is solved using Modified Differential Transformation Method (MDTM) and the result is validated …

Optimized Transconductance Designs To Enhance The Linearity Performance Of Rf Front-End Receiver Circuits In 130 Nm Cmos Technology, Nandini Vitee

Student Works (2020-2029)

Highly linear front-end circuits are greatly desired for wireless receivers to improve the dynamic range. However, intermodulation distortions caused by the non-linear transconductor current limits the linearity of the front-end receiver circuit in CMOS technologies. In addition to the inherent nonlinear effect, the downscaling of CMOS further exacerbates the linearity of the circuit due to lower voltage headroom and high-field mobility. Thus, it is essential to develop effective circuit techniques that can aid linearity enhancement without jeopardizing other preferred performances such as low noise, high conversion gain, and low-power consumption. In this thesis, two different high linear transconductors are presented …

A Brief Bibliometric Survey On Circularly Polarized Antennas For Mobile Communication, Aniket Gunjal, Abhaya Pal Singh

Library Philosophy and Practice (e-journal)

This paper presents a database review on “Circularly Polarized Antennas for Mobile Communication” as it is the emerging technique used by mobile service provider because of having benefits over other types of antennas available.The polarization purity is now the major issue. In some cases due to cross polarization issue the antenna signal is cancelled at receiver side.So, it is necessary to have circularly polarized antenna to avoid this polarization issue because of change in phase of signal. The change in phase of signal is due to striking of wave on the obstacles and it slightly tilted from its direction causes …

Aqueous Redox Flow Batteries With Boron Doped Diamond As An Electrode., Alex M. Bates

Electronic Theses and Dissertations

As the interest and implementation of renewable energy accelerates, so does that of grid energy storage. It is widely believed that a cost-effective energy storage technology will bring about the proliferation of renewable energy. Redox flow battery (RFB) technology represents a promising solution to cost-effective grid energy storage. Compared to other technologies, RFBs have a long lifetime, high efficiency, are non-flammable, significantly reduce cost, and separately scale power and energy. The separation of power and energy enables increased energy capacity by simply adding electrolyte volume. Of the challenges facing RFB technology, one readily apparent is the cost of the active …

The Structural And Magnetic Properties Of Nio/Mn(Ni)-Oxide Magnetic Heterostructured Nanocrystals Synthesized Under Varying Ph Values, Abdullah Al Shafe

Graduate Theses/Dissertations

The role of pH on the structural, morphological, and magnetic properties of hydrothermally synthesized NiO-based magnetic heterostructured nanocrystals (MHNCs) is investigated. The NiO nanocrystals were synthesized using a two-step thermal decomposition process whereas the deposition of the surrounding Mn-based phases was accomplished by hydrothermal means at pH values ranging from 2.4 to 7.0. The resulting heterostructured nanocrystals consist of inverted AFM-FiM NiO/±Mn_xNi_1-xO/±Mn₃O₄ bimagnetic/trimagnetic systems. A complete characterization of the MHNCs was carried using XRD, TEM, EDS, MPMS magnetometry and XPS analysis. Structural investigations revealed predominantly faceted MHNCs ranging in size from 24-30 nm …

Ractive Md Simulation On The Formation Of Amorphous Alumina Layer Using Atomic Layer Deposition (Ald), Yuxuan Lu

Graduate Theses/Dissertations

In this study, a systematic study has been performed by using the large-scale classical reactive molecular dynamics (MD) simulations to model the Atomic Layer Deposition (ALD) processes that generated tan ultra-thin and sub-nano meter amorphous alumina. The ALD process employed both water pulse and (Trimethyl-Aluminum) TMA precursors deposited onto the surface of an aluminum wetting layer. The study varied the sizes of the substrate and the concentrations of water/hydroxide precursors with a range of operating temperature to design the most favorable configurations for the subsequent TMA precursors to add onto. The role of crystallographic orientation of the Al wetting layer …

Single Molecule Super-Resolution Microscopy Study On The Precision With Which Dna Nanostructures Can Orient Fluorescent Dyes, Brett Michael Ward

Boise State University Theses and Dissertations

DNA nanotechnology enables the rapid, programmable self-assembly of novel structures and devices at the nanoscale. Utilizing the simplicity of Watson-Crick base pairing, DNA nanostructures are capable of assembling a variety of nanoparticles in arbitrary configurations with relative ease. Several emerging opto-electronic systems require a high degree of control of both the position and orientation of component fluorescent molecules, and while DNA nanostructures have demonstrated these capabilities, the precision with which DNA can orient fluorescent molecules is not well understood. Determining these bounds is critical in establishing the viability of DNA nanotechnology as a method of assembling fluorescent molecular networks.

In …

Mxenes As Flow Electrodes For Capacitive Deionization Of Wastewater, Naqsh E. Mansoor

Boise State University Theses and Dissertations

The energy-water nexus poses an integrated research challenge, while opening up an opportunity space for the development of energy efficient technologies for water remediation. Capacitive Deionization (CDI) is an upcoming reclamation technology that uses a small applied voltage applied across electrodes to electrophoretically remove dissolved ionic impurities from wastewater streams. Similar to a supercapacitor, the ions are stored in the electric double layer of the electrodes. Reversing the polarity of applied voltage enables recovery of the removed ionic impurities, allowing for recycling and reuse. Simultaneous materials recovery and water reclamation makes CDI energy efficient and resource conservative, with potential to …

Investigation Of Various Techniques For Controlled Void Formation In Fiberglass/Epoxy Composites, Donald A. Klosterman, Charles Browning, Issa Hakim, Kyle Lach

Chemical and Materials Engineering Faculty Publications

The effect of porosity in composite materials has been studied for years due to its deleterious effects on mechanical properties, especially matrix dominated properties. Currently there is an increasing use of composites in infrastructure worldwide, for example bridge components, residential and building structures, marine structures such as piers and docks, and large industrial chemical tanks. Most of these applications use fiberglass composites. Unfortunately, most of the published literature has focused on carbon fiber composites, in which fiber diameter and gas-fiber interactions are different than fiberglass composites. Therefore, the present study was undertaken to revisit the effect of porosity but specifically …

Fabrication Of Magnetocaloric La(Fe,Si)13 Thick Films, N H. Dung, N B. Doan, P De Rango, L Ranno, Karl G. Sandeman, N M. Dempsey

Publications and Research

La(Fe,Si)₁₃–based compounds are considered to be very promising magnetocaloric materials for magnetic refrigeration applications. Many studies have focused on this material family but only in bulk form. In this paper we report on the fabrication of thick films of La(Fe,Si)₁₃, both with and without post-hydriding. These films exhibit magnetic and structural properties comparable to bulk materials. We also observe that the ferromagnetic phase transition has a negative thermal hysteresis, a phenomenon not previously found in this material but which may have its origins in the availability of a strain energy reservoir, as in the cases of …

Miniaturized Ultraviolet Imager Phase Iii, Bradley D. Albright, Nicolas A. Armenta, Colin W. Harrop

Mechanical Engineering

This document details the work to date, June 9, 2020, done by the Cal Poly Mechanical Engineering senior project team, Miniaturized Ultraviolet Imager: Phase III (MUVI III), sponsored by the University of California, Berkeley – Space Sciences Laboratory (UCB SSL). MUVI III is the third senior project team of an ongoing design, MUVI: the prototype of a 2U sized CubeSat intended to capture aurora images in the ionosphere. The first team, MUVI I, finished development of the UV imager. The second team, MUVI II, designed the mirror mounting and deployable door mechanisms. The goal of MUVI phase III is to …

Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom

Mechanical Engineering

This document outlines the critical design details and timeline for the Design for Additive Manufacturing Senior Project sponsored by Solar Turbines, Inc. The scope of this project encompasses the redesign of two of Solar Turbine’s cast parts for metal additive manufacturing in order to minimize lead time, cost, and weight. With the overall objective of performing in-depth analysis exploring affordability & feasibility, this redesign process will aid Solar Turbines in expanding their knowledge of Design for Additive Manufacturing principles and enable them to further incorporate the use of additive manufacturing into their production processes. The first part that the team …

Non-Toxic Soil Thickeners For Reducing Mudslide Intensity, Mitchell William Jensen

Materials Engineering

This project was intended to be a continuation of senior project work done last year by a group consisting of two Materials Engineering students and a Soil Science student. Their report was crucial in identifying a range of food thickeners that could be capable of performing in the mud thickening application. All thickeners that were chosen both this year and last year are biocompatible, to alleviate some toxicity concerns. The food thickeners all belong to a class of compounds known as colloids. Since water is the fluid being thickened, these compounds are more accurately referred to as hydrocolloids. Hydrocolloids are …

The Influence Of Time And Temperature On 7781 Prepreg Outside Storage, Matthew L. Fuentez, Edwin Stuart Ross Viii

Materials Engineering

Investigation into the issue of out of specification flow data revealed that unregulated transportation conditions exposed 7781 prepreg with phenolic resin to temperature fluctuations up to 125°F. The temperature fluctuations have the potential to advance unwanted curing in the prepreg, making it unsuitable for manufacturing. However, this explanation does not account for the prepreg exceeding specifications above the upper limit. Another explanation was investigated that involved exposure to moisture. Moisture could be preventing curing from taking place and thus resulting in higher flow values. Data collection was unable to proceed past the preliminary stages due to the COVID-19 pandemic and …

Comparative Analysis And Dynamic Response Of Garolites Under Temperature Spectrum Using Low Velocity Impact Test, Birendra Chaudhary

Honors Theses

The purpose of this study was to examine the dynamic response of three different grades of garolites under the temperature spectrum. High-Temperature G-11 Sheet (HTG), Impact Resistance Garolite E-glass (HIG), and Economical Garolite (EG) were tested using an Instron Dynatup 8250 impact tester. Three specimens were used for all three composites and were tested at 6 different temperatures, -10^oC, 25^oC, 50^oC, 100^oC, 150^oC and 200^oC using the Low-Velocity Impact Machine with 20 Kip punch shear load cell. The results showed that HIG had the highest resistance to punch …

Dynamic Characterization Of Duroprotect, A Fiber-Reinforced Ballistics Composite, Ivy A. Turner

Honors Theses

Dynamic characterization of materials has become increasingly common, as it is important to understand how materials behave under sudden loads. Understanding these properties can aid in material selection for novel designs. DuroProtect, a fiber-reinforced ballistics composite developed by Rӧchling, was tested for its dynamic properties at high strain-rates. The Split Hopkinson Pressure Bar (SHPB) test was used to obtain dynamic properties at high strain-rates under compressive loading conditions. Tests were initially conducted to validate force equilibriums for each sample. The data measured from the strain gages mounted on the incident and transmission bars and the elastic wave propagation theories yields …

Structure And Deformation Of Carbyne Deposited On A Nickel Substrate, Abigail Eaton

Mechanical Engineering Undergraduate Honors Theses

Carbyne is a nanomaterial of great interest due to its ability to withstand high forces similarly to other carbon allotropes such as graphene or carbon nanotubes. However, it is currently difficult to synthesize and maintain without the assistance of a composite material substrate that the carbyne can be integrated with, which will affect its reaction to varying conditions. This thesis focuses on studying the effects of carbyne on a nickel surface and its mechanical properties to predict its future usages and potential for applications in varying fields. We perform a three-point bending test simulation using molecular dynamics with pure Ni …

Enhancement Of Phase Change Material Sorbitol By Nanoparticle Inclusion For Improving Thermal Energy Storage Capabilities, Joshua Kasitz

Mechanical Engineering Undergraduate Honors Theses

Thermal management of electronic devices has become an increasingly vital field of study with the rapid miniaturization of many key electrical components. With the significant improvement of semiconductor manufacturing and intensified focus on interconnects, electronic devices have decreased in size at an incredible rate. Decreasing spatial requirements is essential to improving device capabilities as the electronic system is able to incorporate more components. Currently, electronic systems are drastically limited by the capabilities of their cooling mechanisms. Smaller devices lead to large increases in the energy density of the system and require more powerful cooling systems to maintain proper component operating …

Sub-/Surface Evaluation Of Industry-Grade Endodontic File Micro-/Nanoscale Structures And Low-Cost, Low-Energy Methods Of Rapidly Annealing And Nitriding Titanium, Nicholas Broadbent

Mechanical Engineering Undergraduate Honors Theses

Because of their unique mechanical properties, shape memory capabilities and biocompatibility, Nickel-titanium alloys are frequently used in the medical industry for a variety of applications including endodontic files. Until now, the performance of industry-standard endodontic files has been characterized by this alloying property and a limited set of macroscale surface structures and features. In this work, High Resolution Transmission Electron Microscopy (HRTEM), Low Resolution Transmission Electron Microscopy (LRTEM), Scanning Electron Microscopy (SEM), and Energy Dispersive X-Ray Spectroscopy (EDX) analyses are conducted at both the surface and sub-surface levels of a wide selection of industry-grade endodontic files currently offered on the …

An All-Optical Excitonic Switch Templated On A Dna Scaffold Operated In The Liquid And Solid Phases, Donald L. Kellis

Boise State University Theses and Dissertations

The natural excitonic circuitry of photosynthetic organisms, including light harvesting antennas, provides a distinctive example of a highly attractive bio-inspired alternative to electronic circuits. Excitonics, which capitalizes on spatially arranged optically active molecules ability to capture and transfer light energy below the diffraction limit of light has garnered recognition as a potential disruptive replacement for electronic circuits. However, assembly of optically active molecules to construct even simple excitonic devices has been impeded by the limited maturity of suitable molecular scale assembly technologies.

An example of nanophotonic circuitry, natural light harvesting antennas employ proteins as scaffolds to organize and self-assemble light-active …

Mitigating Safety Concerns And Profit/Production Losses For Chemical Process Control Systems Under Cyberattacks Via Design/Control Methods, Helen Durand, Matthew Wegener

Chemical Engineering and Materials Science Faculty Research Publications

One of the challenges for chemical processes today, from a safety and profit standpoint, is the potential that cyberattacks could be performed on components of process control systems. Safety issues could be catastrophic; however, because the nonlinear systems definition of a cyberattack has similarities to a nonlinear systems definition of faults, many processes have already been instrumented to handle various problematic input conditions. Also challenging is the question of how to design a system that is resilient to attacks attempting to impact the production volumes or profits of a company. In this work, we explore a process/equipment design framework for …

Questaal: A Package Of Electronic Structure Methods Based On The Linear Muffin-Tin Orbital Technique, Dimitar Pashov, Swagata Acharya, Walter R.L. Lambrecht, Jerome Jackson, Kirill Belashchenko, Athanasios Chantis, Francois Jamet, Mark Van Schilfgaarde

Kirill Belashchenko Publications

This paper summarises the theory and functionality behind Questaal, an open-source suite of codes for calculating the electronic structure and related properties of materials from first principles. The formalism of the linearised muffin-tin orbital (LMTO) method is revisited in detail and developed further by the introduction of short-ranged tight-binding basis functions for full-potential calculations. The LMTO method is presented in both Green's function and wave function formulations for bulk and layered systems. The suite's full-potential LMTO code uses a sophisticated basis and augmentation method that allows an efficient and precise solution to the band problem at different levels of theory, …