Materials Science and Engineering Commons^™

Effects Of Nanoholes Grown By Molecular Beam Droplet Epitaxy On Electrical Properties Of Two Dimensional Electron Gas, Yusuke Hirono

Graduate Theses and Dissertations

The effects of nanoholes, grown by molecular beam droplet epitaxy, on the electrical properties of quantum well (QW) heterostructures are reported. To investigate how the depth of nanoholes affect the electrical properties of the QW heterostructures, the growth conditions for nanoholes were optimized with respect to their depth and density. Using the results of the optimization of the nanohole growth, three InGaAs pseudomorphic quantum wells with nanoholes were investigated with varied depth and a constant density. A QW heterostructure without nanoholes was grown as a reference structure. For all the samples, temperature dependent Hall effect measurements, noise studies as a …

Opto-Electronic Devices With Nanoparticles And Their Assemblies, Chieu Van Nguyen

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

Nanotechnology is a fast growing field; engineering matters at the nano-meter scale. A key nanomaterial is nanoparticles (NPs). These sub-wavelength (< 100nm) particles provide tremendous possibilities due to their unique electrical, optical, and mechanical properties. Plethora of NPs with various chemical composition, size and shape has been synthesized. Clever designs of sub-wavelength structures enable observation of unusual properties of materials, and have led to new areas of research such as metamaterials. This dissertation describes two self-assemblies of gold nanoparticles, leading to an ultra-soft thin film and multi-functional single electron device at room temperature. First, the layer-by-layer self-assembly of 10nm Au nanoparticles and polyelectrolytes is shown to behave like a cellular-foam with modulus below 100 kPa. As a result, the composite thin film (~ 100nm) is 5 orders of magnitude softer than an equally thin typical polymer film. The thin film can be compressed reversibly to 60% strain. The extraordinarily low modulus and high compressibility are advantageous in pressure sensing applications. The unique mechanical properties of the composite film lead to development of an ultra-sensitive tactile imaging device capable of screening for breast cancer. On par with human finger sensitivity, the tactile device can detect a 5mm imbedded object up to 20mm below the surface with low background noise. The second device is based on a one-dimensional (1-D) self-directed self-assembly of Au NPs mediated by dielectric materials. Depending on the coverage density of the Au NPs assembly deposited on the device, electronic emission was observed at ultra-low bias of 40V, leading to low-power plasma generation in air at atmospheric pressure. Light emitted from the plasma is apparent to the naked eyes. Similarly, 1-D self-assembly of Au NPs mediated by iron oxide was fabricated and exhibits ferro-magnetic behavior. The multi-functional 1-D self-assembly of Au NPs has great potential in modern electronics such as solid state lighting, plasma-based nanoelectronics, and memory devices.

Adviser: Ravi F. Saraf

Nickel Aluminum Shape Memory Alloys Via Molecular Dynamics, Keith Ryan Morrison

Open Access Theses

Shape memory materials are an important class of active materials with a wide range of applications in the aerospace, biomedical, and automobile industries. These materials exhibit the two unique properties of shape memory and superelasticity. Shape memory is the ability to recover its original shape by applying heat after undergoing large deformations. Superelasticity is the ability to undergo large, reversible deformations (up to 10%) that revert back when the load is removed. These special properties originate from a reversible, diffusionless solid-solid phase transformation that occurs between a high temperature austenite phase and a low temperature martensite phase. The development of …

Surface Enhanced Raman Spectroscopic Studies Of Pyridine Adsorbed On Ti/Au@Sio2 Film Electrode, Min-Min Xu, Ke Liu, Qing-Hua Guo, Jian-Lin Yao

Journal of Electrochemistry

This study was performed based on shell-isolated nanoparticles-enhanced Raman spectroscopy (SHINERS) technology. The Au@SiO₂ nanoparticles were prepared and characterized by TEM and cyclic voltammetry. It was shown that the shell of SiO₂ was compact. The high quality signal measured by surface enhanced Raman spectroscopy (SERS) was obtained from the adsorbed pyridine on Ti/Au@SiO₂ electrode. The origin of the SERS signals was further confirmed by testing Pt and Ni electrodes. In addition, potential dependent adsorption behavior was investigated. It was found that pyridine was adsorbed parallel on the surface from -0.1 V to -0.6 V, and converted to …

Horseradish Peroxidase-Attapulgite Clay Nanocomposites: Fabrication And Application To Sensing The Extracellular H2O2 Released From Cells, Ping Wu, Chen-Xin Cai

Journal of Electrochemistry

The nanostructured attapulgite clay was employed as a support matrix for immobilizing horseradish peroxidase (HRP). FTIR and electrochemical methods demonstrated that HRP had been effectively assembled on attapulgite surface with the formation of HRP-attapulgite nanocomposites. The HRP-attapulgite hybrid was deposited on the glassy carbon (GC) electrode forming the HRP-attapulgite/GC electrode. Cyclic voltammetric results showed a pair of well-defined redox peaks, which were ascribed to direct electron transfer (DET) of HRP, with the formal potential E₀′ = -335 mV (vs. SCE) in the phosphate buffer solution (PBS, pH 7.0). The dependence of E₀′ on solution pH indicated …

Effects Of Conformational Transformations On Electronic Transport Properties Of Optical Molecular Switches: An Ab Initio Study, Yuan-Yuan He, Jian-Wei Zhao

Journal of Electrochemistry

A series of model molecules with 4 kinds of conformational transformations have been investigated as optical molecular switches by using density functional theory combined with nonequilibrium Green’s function method. The theoretical calculations show that molecules after conformational transformations have photoswitching characteristics. We find that the photochromic molecules with the same conformational transformation usually have a similar current on/off state when they are applied as photoshwitches. Among these transformations, the molecular switch with E(“trans”)/Z(“cis”)-isomerisation of the NN double bond has the highest current on-off ratio. The influences of the energy gap (HLG) between the highest occupied molecular orbital (HOMO) and the …

23Na Mas Nmr Spectroscopic Study Of Na2Mnpo4F As Cathode Material For Sodium-Ion Battery, Xu Hou, Gui-Ming Zhong, Xiao-Chen Lin, Zi-Geng Liu, Xiao-Biao Wu, Yong Yang

Journal of Electrochemistry

The Na₂MnPO₄F is one of the promising cathode materials for the sodium ion batteries. In the paper, we employed the ex situ X-ray diffraction and solid state NMR techniques to study the charge and discharge processes of this material, including the crystal structure and sodium sites changes. The ex situ x-ray diffraction patterns showed that two new diffraction peaks could be observed at 31^o and 36^o indicating an intermediate phase formed with the extraction of Na⁺. From the ²³Na MAS NMR spectrum of the material, three peaks were seen at -209 …

Effects Of Oxygen Coverage And Hydrated Proton Model On The Dft Calculation Of Oxygen Reduction Pathways On The Pt(111) Surface, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

DFT calculation is used to study various possible steps in the oxygen reduction reaction (ORR), including the adsorption and dissociation process of O₂ and the serial protonation process of dissociated products to form H₂O on the Pt(111) surface. By using slabs of different sizes, and different numbers of pre-adsorbed oxygen atoms, the coverage effects on the pathways are investigated. The calculated results using different hydrated proton models are also compared. It is shown that the initial step of the ORR is the formation of a protonated end-on chemisorbed state of OOH*, which can transform to an unprotonated …

Developent Of A Phospholipid Encapsulation Process For Quantum Dots To Be Used In Biologic Applications, Logan Grimes

Master's Theses

The American Cancer Society predicts that 1,665,540 people will be diagnosed with cancer, and 585,720 people will die from cancer in 2014. One of the most common types of cancer in the United States is skin cancer. Melanoma alone is predicted to account for 10,000 of the cancer related deaths in 2014. As a highly mobile and aggressive form of cancer, melanoma is difficult to fight once it has metastasized through the body. Early detection in such varieties of cancer is critical in improving survival rates in afflicted patients. Present methods of detection rely on visual examination of suspicious regions …

Electroplating Of Nanoengineered Polymer Substrate, Brandon Voelker

Masters Theses

The development of a polyethylene based polymer with metallic inclusions, a nanoengineered polymer, has recently opened up great potential for many new commercial and industrial applications. The major advantage of developing these nanoengineered polymers is to be able to tailor the resistance and other properties by varying the composition of the polymer. The industrial usage of this polymer benefits from the addition of an electrically conductive, metallic coating. This research develops methods of electroplating nickel and copper layers on to the polymer substrates using DC and pulsed techniques.

Electroplating is conducted in a 1000 mL beaker using a specialized plating …

Fabrication And Characterization Of Amorphous/Nanocrystalline Thin Film Composite, Benjamin Seth Newton

Graduate Theses and Dissertations

Combining the absorption abilities of amorphous silicon and the electron transport capabilities of crystalline silicon would be a great advantage to not only solar cells but other semiconductor devices. In this work composite films were created using molecular beam epitaxy and electron beam deposition interchangeably as a method to create metallic precursors. Aluminum induced crystallization techniques were used to convert an amorphous silicon film with a capping layer of aluminum nanodots into a film composed of a mixture of amorphous silicon and nanocrystalline silicon. This layer was grown into the amorphous layer by cannibalizing a portion of the amorphous silicon …

Synthesis Of Platinum Nanocrystallites And Possible Electrocatalytic Properties For Methanol, Lei-Lei Lu, Bao-Zhong Du, Sha Sun, Jin-Fen Niu, Jie Zhao

Journal of Electrochemistry

Platinum nanocrystallites were synthesized by the colloidal method using oxamide as the stabilizer. The morphologies and electrocatalytic performances for methanol of platinum nanocrystallites prepared at different pH values and with different reactant ratios of precursor and stabilizer were investigated. It was found that the platinum nanocrystallites synthesized at pH=5 and with the reactant ratio of 1:20 showed the best electrocatalytic activity for methanol. The peak current density reached up to 1709 μA·cm^-2. Furthermore, the electrocatalytic activity of platinum nanocrystallites for methanol reduced significantly although the cyclic voltammograms in the blank solution were not obviously changed after exposing in …

Preparation And Electrochemical Performances Of Cofe2O4/Gns Nanocomposites As Anode Material For Lithium Ion Battery, Mo-Chao Cai, Sen-Rong Cai, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The CoFe₂O₄/GNS was synthesized by a simple one-pot solvothermal method. The results obtained by X-ray diffraction (XRD) and transmission electron microscopy (TEM) showed that the CoFe₂O₄ particles with sizes of 15 nm dispersed on the surface of graphene uniformly. Electrochemical tests indicated that the CoFe₂O₄/GNS nanocomposite exhibited excellent cyclic stability with almost 95.8% capacity retention after 100 cycles at the current density of 500 mA·g^-1 and delivered a high reversible capacity of 482 mAh·g^-1 at the current density of 2 A·g^-1.

Functionalization Of Carbon Nanotube Yarn By Acid Treatment, Heath E. Misak, Ramazan Asmatulu, Mat O'Malley, Emil Jurak, Shankar Mall

Faculty Publications

Carbon nanotube (CNT) yarn was functionalized using sulfuric and nitric acid solutions in 3:1 volumetric ratio. Successful functionalization of CNT yarn with carboxyl and hydroxyl groups (e.g., COOH, COO–, OH, etc.) was confirmed by attenuated total reflectance spectroscopy. X-ray diffraction revealed no significant change to the atomic in-plane alignment in the CNTs; however, the coherent length along the diameter was significantly reduced during functionalization. A morphology change of wavy extensions protruding from the surface was observed after the functionalization treatment. The force required to fracture the yarn remained the same after the functionalization process; however, the linear density was increased …

Carbon Allotrope Dependence On Temperature And Pressure During Thermal Decomposition Of Silicon Carbide, Munson J. Anderson

Theses and Dissertations

Bulk CNT and graphene films form on SiC using a metal-catalyst-free thermal decomposition approach. In this work, the background vacuum pressure and temperature used in the decomposition process are varied to investigate their impact on the type and quality of carbon allotrope formed on the SiC substrate. The carbon nanostructure growth is performed using two approaches, both of which involve intense heating (1400-1700°C) of SiC under moderate vacuum conditions (0.01 - 0.00001 Torr). The first growth method uses a conventional graphite resistance furnace capable of annealing waferscale samples over 1700°C under vacuum. Using this approach, post-growth characterization is performed using …

Zno Nanosheet Arrays Constructed On Weaved Titanium Wire For Cds-Sensitized Solar Cells, Cuncun Wu, Lin Wei, Yitan Li, Chang Liu, Jun Jiao, Yanxue Chen, Liangmo Mei

Mechanical and Materials Engineering Faculty Publications and Presentations

Ordered ZnO nanosheet arrays were grown on weaved titanium wires by a low-temperature hydrothermal method. CdS nanoparticles were deposited onto the ZnO nanosheet arrays using the successive ionic layer adsorption and reaction method to make a photoanode. Nanoparticle-sensitized solar cells were assembled using these CdS/ZnO nanostructured photoanodes, and their photovoltaic performance was studied systematically. The best light-to-electricity conversion efficiency was obtained to be 2.17% under 100 mW/cm/cm² illumination, and a remarkable shortcircuit photocurrent density of approximately 20.1 mA/cm² was recorded, which could attribute to the relatively direct pathways for transportation of electrons provided by ZnO nanosheet arrays as …

Cds Quantum Dot-Sensitized Solar Cells Based On Nano-Branched Tio2 Arrays, Chang Liu, Yitan Li, Lin Wei, Cuncun Wu, Yanxue Chen, Liangmo Mei, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

Nano-branched rutile TiO2 nanorod arrays were grown on F:SnO2 conductive glass (FTO) by a facile, two-step wet chemical synthesis process at low temperature. The length of the nanobranches was tailored by controlling the growth time, after which CdS quantum dots were deposited on the nano-branched TiO2 arrays using the successive ionic layer adsorption and reaction method to make a photoanode for quantum dot-sensitized solar cells (QDSCs). The photovoltaic properties of the CdS-sensitized nano-branched TiO2 solar cells were studied systematically. A short-circuit current intensity of approximately 7 mA/cm2 and a light-to-electricity conversion efficiency of 0.95% were recorded for cells based on …

Design And Development Of A Novel Glucose Biosensor Based On The Ferrocene-Functionalized Fe3O4 Nanoparticles/Carbon Nanotubes/Chitosan Nanocomposite Film Modified Electrode, Hua-Ping Peng, Dai-Jun Zha, Wei Chen, Ai-Lin Liu, Xin-Hua Lin

Journal of Electrochemistry

A novel platform for the fabrication of glucose biosensor was successfully constructed by entrapping glucose oxidase (GOD) in a ferrocene monocarboxylic acid-aminated Fe₃O₄ magnetic nanoparticles conjugate (FMC-AFNPs)/chitosan (CS)/multiwall carbon nanotubes (MWNTs) nanocomposite. The formation of FMC-AFNPs could effectively prevent the leakage of ferrocene and retain its electrochemical activity. This GOD/FMC-AFNPs/CS/MWNTs matrix provided a biocompatible microenvironment for retaining the native activity of the immobilized GOD. Moreover, the presence of MWNTs enhanced the charge-transport properties of the composite and facilitated electron transfer between the GOD and the electrode for the electrocatalysis of glucose. Under the optimal conditions the designed …

Pulse Electrodeposition Of Pd-Ni Alloy Nanoparticles For Electrocatalytic Oxidation Of Formic Acid, Fang-Zu Yang, Jun-Pei Yue, Zhong-Qun Tian, Shao-Min Zhou

Journal of Electrochemistry

The Pd-Ni alloy nanoparticles with nickel atomic contents of 12.0%, 16.4% and 22.6% were successfully electrodeposited from a Pd-Ni alloy electrolyte by square wave pulse plating. The alloy nanoparticles were in the spherical shape with a diameter of 50 ~ 80 nm. As the growth potential of the alloy was negatively shifted, the nickel content of the alloy was increased, and the size of the nanoparticles was almost the same, whereas the number, the degree of crosslinking and the real active area of the nanoparticles were increased. As the nickel content of the alloy nanoparticles increased, the peak current for …

Development And Application Of Biomimetic Electrospun Nanofibers In Total Joint Replacement, Wei Song

Wayne State University Dissertations

Failure of osseointegration (direct anchorage of an implant by bone formation at the bone-implant surface) and implant infection (such as that caused by Staphylococcus aureus, S. aureus) are the two main causes of implant failure and loosening. There is a critical need for orthopedic implants that promote rapid osseointegration and prevent bacterial colonization, particularly when placed in bone compromised by disease or physiology of the patients. A better understanding of the key factors that influence cell fate decisions at the bone-implant interface is required. Our study is to develop a class of "bone-like" nanofibers (NFs) that promote osseointegration while preventing …

Fundamental Studies Of Supported Graphene Interfaces : Defect Density Of States In Graphene Field Effect Transistors (Fets) And Ideal Graphene - Silicon Schottky Diodes, Dhiraj Sinha

Legacy Theses & Dissertations (2009 - 2024)

The physics of transport in atomically thin 2D materials is an active area of research, important for understanding fundamental properties of reduced dimensional materials and for applications. New phenomena based on graphene may include properties of topologically protected insulators. Applications of these materials are envisioned in electronics, optoelectronics and spintronics.

Investigating Quantum Oscillations In The Thermal Coefficient Of Resistivity Of Ultra-Thin Ag Capping Layers On Cu For Ic Interconnect Applications, Elroy Tatem

Legacy Theses & Dissertations (2009 - 2024)

As the semiconductor industry continues to scale feature sizes, scattering from phonons, surfaces, and grain boundaries result in an increase of metal interconnect resistivity in state-of-the-art integrated circuits (ICs). The interconnect chapter of the 2011 International Technology Roadmap for Semiconductors (ITRS) stated that there are currently no manufacturable solutions in the near term for suitable Cu replacements. Previous studies of thin Ag films deposited on Cu demonstrated oscillations in the electron-phonon interactions within the bilayer system. This thesis investigates oscillations in the resistive properties of the Ag/Cu bilayer system and discusses the applicability of these oscillations to the resistivity challenges …

Nanostructured Tiox As A Catalyst Support Material For Proton Exchange Membrane Fuel Cells, Richard Phillips

Legacy Theses & Dissertations (2009 - 2024)

Recent interest in the development of new catalyst support materials for proton exchange membrane fuel cells (PEMFCs) has stimulated research into the viability of TiO₂-based support structures. Specifically, substoichiometric TiO₂ (TiO_x) has been reported to exhibit a combination of high conductivity, stability, and corrosion resistance. These properties make TiO_x-based support materials a promising prospect when considering the inferior corrosion resistance of traditional carbon-based supports. This document presents an investigation into the formation of conductive and stable TiO_x thin films employing atomic layer deposition (ALD) and a post deposition oxygen reducing anneal (PDORA). …

Development Of Novel Technologies To Enhance Performance And Reliability Of Iii-Nitride Avalanche Photodiodes, Puneet Harischandra Suvarna

Legacy Theses & Dissertations (2009 - 2024)

Solar-blind ultraviolet avalanche photodiodes are an enabling technology for applications in the fields of astronomy, communication, missile warning systems, biological agent detection and particle physics research. Avalanche photodiodes (APDs) are capable of detecting low-intensity light with high quantum efficiency and signal-to-noise ratio without the need for external amplification. The properties of III-N materials (GaN and AlGaN) are promising for UV photodetectors that are highly efficient, radiation-hard and capable of visible-blind or solar-blind operation without the need for external filters. However, the realization of reliable and high performance III-N APDs and imaging arrays has several technological challenges. The high price and …

Growth And Characterization Of Graphene On Cuni Substrates, Parul Tyagi

Legacy Theses & Dissertations (2009 - 2024)

Graphene is a single layer of sp2 bonded carbon atoms that crystallizes in the honeycomb structure. Because of its true two-dimensional structure, it has very unique electrical properties, including a very high carrier mobility that is symmetric for holes and electrons. To realize these unique properties, it is important to develop a method for growing graphene films with uniform thickness and low defect density. One of the most popular methods of growth is by chemical vapor deposition on Cu substrates, because it is self-limited. However many applications require the growth of graphene films that are more than one atomic layer …

The Influence Of Impurities And Metallic Capping Layers On The Microstructure Of Copper Interconnects, Michael Rizzolo

Legacy Theses & Dissertations (2009 - 2024)

As copper interconnects have scaled to ever smaller dimensions on semiconductor devices, the microstructure has become increasingly detrimental for performance and reliability. Small grains persist in interconnects despite annealing at high temperatures, leading to higher line resistance and more frequent electromigration-induced failures. Conventionally, it was believed that impurities from the electrodeposition pinned grain growth, but limitations in analytical techniques meant the effect was inferred rather than observed.

Experimental And Simulation Studies Of Printability Of Buried Euv Mask Defects And Study Of Euv Reflectivity Loss Mechanisms Due To Standard Euv Mask Cleaning Processes, Mihirkant Upadhyaya

Legacy Theses & Dissertations (2009 - 2024)

There's a big push for development and commercialization of extreme ultraviolet (EUV) lithography for high-volume semiconductor manufacturing of 14 nm half-pitch patterning and beyond. One of the primary concerns for making this a reality has been the ability to achieve defect-free masks. My study is focused on two aspects related to the performance degradation of the EUV masks namely EUV mask cleaning induced reflectivity loss mechanisms, and the buried multilayer phase defects in EUV masks.

In-Situ Tem Plasma Chip Nanofabrication And Characterization, Xuebo Cui

Dissertations, Master's Theses and Master's Reports - Open

A silicon-based microcell was fabricated with the potential for use in in-situ transmission electron microscopy (TEM) of materials under plasma processing. The microcell consisted of 50 nm-thick film of silicon nitride observation window with 60μm distance between two electrodes. E-beam scattering Mont Carlo simulation showed that the silicon nitride thin film would have very low scattering effect on TEM primary electron beam accelerated at 200 keV. Only 4.7% of primary electrons were scattered by silicon nitride thin film and the Ar gas (60 μm thick at 1 atm pressure) filling the space between silicon nitride films. Theoretical calculation also showed …

Cnt Membrane Platforms For Transdermal Drug Delivery And Aptamer Modulated Transport, Tao Chen

Theses and Dissertations--Chemical and Materials Engineering

CNT membrane platforms are biomimetic polymeric membranes imbedded with carbon nanotubes which show fast fluid flow, electric conductivity, and the ability to be grafted with chemistry. A novel micro-dialysis probe nicotine concentration sampling technique was proposed and proved in vitro, which could greatly improve the efficiency and accuracy of future animal transdermal studies. To enhance the scope of transdermal drug delivery which was limited to passive diffusion of small, potent lipophilic drugs, a wire mesh lateral electroporation design was also proposed which could periodically disrupt the skin barrier and enhance drug flux.

It was shown that AMP binding aptamer …

Addressing Public Health Risks Of Persistent Pollutants Through Nutritional Modulation And Biomimetic Nanocomposite Remediation Platforms, Bradley J. Newsome

Theses and Dissertations--Chemistry

Due to their relative chemical stability and ubiquity in the environment, chlorinated organic contaminants such as polychlorinated biphenyls (PCBs) pose significant health risks and enduring remediation challenges. Engineered nanoparticles (NPs) provide a novel platform for sensing/remediation of these toxicants, in addition to the growing use of NPs in many industrial and biomedical applications, but there remains concern for their potential long-term health effects. Research highlighted herein also represents a transdisciplinary approach to address human health challenges associated with exposure to PCBs and NPs. The objectives of this dissertation research are two-fold, 1) to develop effective methods for capture/sensing and remediation …