Materials Science and Engineering Commons^™

Effect Of Wall Movement On Porosity Formation In Ductile Iron Castings Under Varying Processing Parameters, Shamsul Alam

College of Graduate Studies: Theses & Dissertations

Shrinkage porosity is a major defect that significantly impairs the mechanical properties and overall performance of ductile iron castings. Although graphite formation during solidification induces volumetric expansion, this expansion alone is insufficient to fully compensate for the shrinkage occurring throughout solidification. During the solidification and cooling of ductile iron, multiple phase transformations occur, resulting in dynamic volume changes that exert pressure on mold walls and internal cavities. These pressures can deform mold walls and casting surfaces, leading to defects such as swell and porosity, while also influencing shrinkage formation. This study aims to analyze the mechanisms of porosity formation and …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

Overcoming Resolution Vs. Throughput Trade-Offs In Ceramic Material Extrusion Additive Manufacturing Via Viscoelastic Filament Stretching, Abid H. Rafi, David W. Lipke, Jeremy L. Watts, Gregory E. Hilmas, Ming C. Leu

Materials Science and Engineering Faculty Research & Creative Works

Fabricating large, monolithic ceramic parts using material-extrusion additive manufacturing remains challenging due to difficulty maintaining uniform moisture content during printing, which can lead to drying-induced defects such as warping and cracking, especially as part size and print time increase. Fabricated parts have trade-offs among print resolution, high throughput, and structural fidelity. Our study has shown that increasing the ratio of nozzle traverse speed vs. material extrusion speed increases filament stretching in viscoelastic ceramic paste, helping to overcome the trade-offs between resolution and throughput. Using aqueous ZrB2–SiC (70/30 vol.%) as a representative ultra-high temperature ceramic paste, rheological characterisation revealed viscoelastic yield-stress …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Effect Of Complex Alloying Elements On Oxide Scale Formation And Water-Jet Descaling Performance On Continuously Cast Low-Carbon Steels, Tochukwu P. Ojiako, Tsvetkov Dmitry, Mario Buchely, Haiming Wen, Simon N. Lekakh, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

The formation and evolution of oxide scale in contact with mold flux during continuous casting, subsequent reheating, and hydraulic descaling are strongly governed by steel chemistry. To elucidate the effect of complex alloying elements (Si, Mn, and Cr), two industrially produced continuously cast low-carbon steel grades for manufacturing stamped parts (a base and alloyed steel grade) were investigated. The objective was to determine how alloying elements influence oxidation behavior, scale morphology, interfacial adhesion, and water-jet descaling efficiency. Continuously cast slab specimens were subjected to controlled thermal and atmospheric oxidation cycles simulating multistage industrial practice. Three initial surface conditions (industrial as-cast, …

Simulated Lunar Gravity Testing Of A Magnetic And Electrostatic System For Beneficiating Lunar Regolith, Blake A. Coffman, Gabriel Porter, Lindsay Manteufel, Mitchell Cottrell, Jeffrey D. Smith, David J. Bayless, William Shonberg, Frank D. Han, Fateme Rezaei, Kirby Runyon

Materials Science and Engineering Faculty Research & Creative Works

We present the design and testing of a lunar regolith beneficiation device that utilizes magnetic and electrostatic separation methods to concentrate desired minerals by removing unwanted material, such as the mineral anorthite, from bulk lunar regolith. The beneficiated materials would have value for downstream in-situ resource utilization (ISRU) processes such as metal extraction, oxygen extraction, and metal oxide additive manufacturing processes. The apparatus uses a dual-strength magnet system with N52 and N42 neodymium magnets to separate particles by magnetic susceptibility. The electrostatic separation system, which acts like a sieve, sorts the regolith simulant by particle size using a single-phase 50% …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Viscoelastic Behavior Of Magnetically Filled Pdms Elastomers: Influence Of Filler Loading And Particle Type, Madison Procyk

College of Graduate Studies: Theses & Dissertations

Magnetorheological elastomers (MREs) offer a promising pathway for soft, magnetically actuated drug‑delivery systems, yet material‑selection guidelines remain unclear due to limited comparative data across particle chemistries, size scales, and concentrations. This study systematically evaluates how magnetic filler type (carbonyl iron and magnetite) and particle size (micro vs. nano), at two weight percentages – 40 wt% and 50 wt% – in Sylgard 184 PDMS influence the viscoelastic behavior of MREs intended for compliant biomedical actuation. Eight particle formulations were prepared through sieving, controlled mixing, vacuum degassing, and isotropic curing, producing nineteen total specimens (16 with filler particles and 3 without). Dynamic …

Effect Of Graphene Oxide On The Upconversion Photoluminescence Behavior Of Er/Yb Co-Doped Pvdf-Go Composite Nanofibers, Saptasree Bose, Jack Ryan Summers, Bhupendra B. Srivastava, Karen Lozano, Victoria Padilla-Gainza

Mechanical Engineering Faculty Publications

Upconversion photoluminescence (UCPL) materials, particularly rare-earth (RE) doped nanoparticles, have garnered significant attention due to their ability to convert near-infrared (NIR) excitation into visible emission, offering benefits such as high photostability, long lifetimes, low autofluorescence, and deep tissue penetration. Among various platforms, polymer-based one-dimensional (1D) nanofibers with in-situ lanthanide doping remain relatively unexplored, despite their superior mechanical flexibility, processability, and potential for improved luminescence performance. In this study, we report the fabrication and UCPL quenching behavior of Er3+/Yb3+ co-doped polyvinylidene difluoride (PVDF) nanofibers incorporated with graphene oxide (GO), synthesized for the first time using the scalable Forcespinning® technique. PVDF, a …

Areosense, Josephine Turney

Williams Honors College, Honors Research Projects

The AeroSense growing system is designed to make indoor aeroponic gardening easy and accessible for everyone. By combining sensors, automation, and AI, the system can monitor and adjust humidity, lighting, and nutrient levels to help plants thrive without requiring expert knowledge. The goal is to create a self-regulating garden that takes the guesswork out of growing fresh herbs and vegetables at home. The project involves building a working aeroponic prototype equipped with misters, pumps, and environmental sensors, all managed by a Raspberry Pi. Using computer vision and machine learning, AeroSense will be able to assess plant health and respond automatically …

Using A Record Player Inspired Probe System To Investigate Adhesion And Friction Of Tire Rubber At Micrometer Length Scales, Kyle J. Galigher, Brendan Schmitt

Williams Honors College, Honors Research Projects

We will be using the principles behind how a record player turns physical grooves into electrical signals to develop a device that can be used to measure the surface of tires. The device will be capable of measuring the surface roughness of rubber samples from both new and worn tires, in order to compare the differences between them. It will be operable at varying speeds, and will produce electrical signals that correspond to the bumps along the surface of the rubber. The design will be carried out and optimized with the use of SolidWorks modeling, finite element analysis, motion analysis, …

Mechanical Behavior Of Additively Manufactured Ti-6al-4v Eli Parts: Effects Of Laser Parameter Selection, Samuel Lopez

UNF Graduate Theses and Dissertations

Additive manufacturing (AM) of TI-6AL‑4V Extra‑Low Interstitial (ELI) enables complex geometries for fatigue‑critical medical device applications, yet fatigue performance remains sensitive to process‑induced defects. This work investigates the effect of laser process parameter selection on the microstructure, mechanical properties, and fatigue behavior of TI- 6AL‑4V ELI fabricated via laser powder bed fusion (L‑PBF) using a Renishaw RenAM system. The influence of laser parameters was isolated by holding powder chemistry, build orientation, scan strategy, sub‑transus annealing, and post‑processing constant between a non‑optimized baseline and an optimized parameter set selected based on tensile performance.

Optical microscopy showed the optimized condition exhibited improved …

Thermomechanical Modeling Of Transpiration Surfaces For Hypersonic Propulsion, Spencer D. Smith

Graduate Studies Theses and Dissertations 2026

Hypersonic flight vehicles are a promising form of high speed passenger transport and efficient space access architectures. However, they are fundamentally a thermally limited technology. High heat fluxes exceeding 10 MW/m2 and gas temperatures between 3000-4000K can be found both within the engine, and on the outer surface. Current conventional engineering materials are non-viable at these conditions. In order to make these materials viable, active cooling strategies could be utilized. One particularly promising type is transpiration cooling, where a coolant is diffused through a porous surface. Although researched heavily in the 1960s, adoption is still minimal. Part of the reason …

Machine Learning Modeling Of In-Situ Effective Thermal Conductivities And Ablation Behaviors Of Ceramic Matrix Composites Under Hydrogen Combustion Environments For Gas Turbine Engines, Jayanta Bhusan Deb

Graduate Studies Theses and Dissertations 2026

Through the integration of experimental characterization, machine learning, deep learning, numerical modeling, and physics-informed artificial intelligence, this dissertation explores the thermal performance of polymer-derived ceramic matrix composites (CMCs) for hydrogen combustion environments. The polymer infiltration and pyrolysis (PIP) process was used to create Yttria-stabilized zirconia (YSZ)-fiber-reinforced ceramic matrix composites, which were then experimentally assessed under hydrogen torch and hydrogen combustion conditions typical of next-generation gas turbine and aerospace propulsion systems. Front- and back-surface temperature measurements were used to continually monitor thermal reactions, and post-test microstructural characterization and numerical simulations were carried out to evaluate material integrity and heat-transfer behavior. To …

Study On Fracture Toughness Under Different Modes Through Continuum Damage Mechanics Based Fracture Locus, Yeting Sun

Graduate Studies Theses and Dissertations 2026

Traditional elastic-plastic fracture mechanics (EPFM) relies on crack-tip analysis, whereas continuum damage mechanics (CDM) is typically calibrated from uncracked bodies. This dissertation aims to bridge the gap between these two fundamental branches by explicitly linking fracture toughness with ductile damage models. Based on the assumptions regarding Mode I crack deformation, analytical solutions are derived to establish a novel relationship among Mode I fracture toughness, CDM-based ductile fracture strain, and material strain hardening capability. This theoretical framework is subsequently extended to encompass Mode II and Mode III loading conditions. To validate the proposed relationships, finite element (FE) models are developed in …

Advanced Ysz/Si(B)Cn And Bnnt/Si(B)Cn Ceramics Matrix Composites For Extreme Environments In Hydrogen Combustion, Yiting Wang

Graduate Studies Theses and Dissertations 2026

The growing demand for carbon-neutral energy conversion has accelerated the development of hydrogen-fueled gas turbine systems, which operate at significantly higher temperatures and more chemically aggressive environments than conventional natural gas turbines. To meet these stringent requirements, ceramic matrix composite (CMC) materials consisting of yttria-stabilized zirconia (YSZ) fiber reinforced Si(B)CN ceramic matrix were developed. To further enhance in-plane heat dissipation, thermal stability, thermal shock resistance, and thermal cycling performance, a Si(B)CN/Boron Nitride Nanotubes (BNNT) nanocomposite coating was incorporated onto the YSZ/Si(B)CN composites. Microstructural characterization confirmed the formation of a continuous Si(B)CN ceramic matrix reinforced with uniformly distributed BNNTs. The resulting …

A Framework For Optimizing Creep Model Parameters From Conventional And Accelerated Creep Tests, William D. Day

Graduate Studies Theses and Dissertations 2026

The demand for efficiency in power generation and propulsion requires higher firing temperatures and reduced cooling air consumption which raises metal temperatures. This makes simplistic creep evaluations, such as Larson-Miller and Orr-Sherby-Dorn parameters, inadequate. Finite element analysis (FEA) must simulate primary and secondary creep, predict failure, and provide design guidance. Gas turbine components, expected to last over 100,000 hours, often require extrapolation of limited test data for new materials. It is essential that robust creep simulations be developed efficiently, accurately, and effectively use limited test data.

This dissertation describes an optimized framework for efficient creep testing and rapid construction of …

Processing, Characterization And Performance Of Ceramic Liners For Hydrogen Gas Turbine Engines, Fahim Faysal

Graduate Studies Theses and Dissertations 2026

Advanced ceramics and ceramic matrix composites (CMCs) are known for their endurance at high temperatures. This study investigated the fabrication and testing of two material systems: silicon carbide nitride (SiCN) reinforced with yttria-stabilized zirconia (YSZ) fiber manufactured through polymer infiltration and pyrolysis (PIP), and 3D-printed alumina (Al₂O₃) ceramics. The CMC thermal stability at high temperatures was explored through a hydrogen torch test. The CMC surface could withstand a temperature of 1,400°C for 10 minutes during the torch test. Furthermore, the internal surface of a hydrogen combustion chamber was coated with CMC to assess its applicability as a protective barrier against …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Parts, Logan Trimmer

Harrisburg University Other Works

Presentation covering the broad strokes of the project. The goal was to prove the viability of hybrid/additive manufacturing for high stress automotive applications. This project focused on recreating a piston from an old engine to examine if hybrid manufacturing could be used for such applications. On a small scale, hybrid manufacturing was able to be more cost effective if the costs of the equipment and electricity were ignored. The decision to ignore those costs came from the inability to find accurate prices for industrial casting.

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Components, Logan Trimmer

Harrisburg University Other Works

The goal of this research was to establish the viability of using hybrid manufacturing for automotive applications. By verifying that high-stress components can be created, it can be assumed that any other lower stress part could be made to match the strength requirements. A limiting factor of adoption for hybrid manufacturing is how new the technology is. Studies on time and cost were performed allowing for comparisons with traditional manufacturing technologies (casting, forging, milling) used in automotive applications. This research utilized a Haas Automation UMC750 5-axis CNC mill with a Meltio laser wire direct energy deposition attachment. Fusion 360 was …

Numerical Simulation Of Micro-Cutting Processes For The Estimation Of Material Fracture Toughness, Juan J. Lainez

Graduate Studies Theses and Dissertations 2026

Accurate determination of plane-strain fracture toughness is essential for structural integrity assessments of engineering components, yet conventional ASTM standardized testing methods require large, notched specimens that are impractical in many industrial and research contexts. This thesis presents a finite element method-based approach for estimating the mode I plane-strain fracture toughness of engineering materials from orthogonal micro-cutting simulations if the continuum damage mechanics-based fracture locus is calibrated. This method will eliminate the need for pre-cracked specimens while maintaining physically grounded fracture mechanics principles. The methodology applies to the Atkins energy-based cutting force model, in which the depth-independent intercept of the specific …

Stiffening Of Soft Silicone Upon Deep Uv Treatment As Characterized Using Nanoindentation, Amanda Wilder, Zaria Booth, Caden Obermeyer, Saika Sharmin, Venkat Maruthamuthu

Mechanical & Aerospace Engineering Faculty Publications

Silicones are elastomers that have a wide variety of uses, including biomedical applications such as the coating of biomedical devices and as implants. Soft silicones with mechanical properties similar to those of biological tissues have particularly gained use as substrates for cell culture in mechanobiology studies. In this context, it would be desirable to be able to alter their surface mechanical properties with a relatively simple physical treatment. While deep ultraviolet (deep UV) or ultraviolet C (UV-C) treatment has been previously used as a surface treatment method for stiffer silicones formulations, the effect of this treatment on soft silicones relevant …

Effect Of Local Steel Slag Incorporation On The Mechanical Properties Of Concrete, Ahmed Safaa Tariq Karmah, Wissam Khadum Alsaraj, Luma A. Zghair

Al-Esraa University College Journal for Engineering Sciences

The increasing interest in the production of concrete through the utilization of inexpensive materials has caused a rise in the number of studies concerning the use of materials with cementitious properties, such as Silica Fume, Slag, Fly Ash and other pozzolanic materials. Moreover, the increasing amounts of Steel Slag being produced from local factories that are being deposited without an available method of disposal provides an opportunity to harness the Slag in the production of an inexpensive, and possibly better concrete. Slag has been used as both an addition and substitution of the cement and fine aggregate. The mixtures included …

Decoding Climate Change: A Comprehensive Statistical Insight Into Temperature Anomalies In Iraq And Its Neighboring Countries, Jameel T. Al-Naffakha, Mohammed R. Al-Qassabanda, Israa Jafar

Al-Esraa University College Journal for Engineering Sciences

This study applies advanced statistical techniques, including the Mann-Kendall Trend Test and ARIMA forecasting, to validate and predict temperature anomalies across Iraq and its neighboring countries (2014–2024). Findings confirm a statistically significant warming trend (p < 0.00000005) across all nations, with Syria (1.02°C) and Turkey (0.97°C) experiencing the highest anomalies. GIS-based spatial analysis highlights regional disparities, identifying climate-vulnerable zones. The persistent rise in temperature anomalies correlates with worsening water scarcity, desertification, and extreme weather events, including prolonged droughts and heatwaves. Iraq’s peak anomaly (1.48°C) has exacerbated heat stress, agricultural decline, and reduced river inflows, while Kuwait and Saudi Arabia struggle to maintain critical infrastructure under record-breaking temperatures exceeding 50°C. These climate shifts pose severe risks to water availability, food security, and energy demand, necessitating urgent policy interventions. Key recommendations include enhanced water resource management, climate-adaptive agriculture, and renewable energy expansion. If left unaddressed, rising temperatures could destabilize the region, increasing socio-economic vulnerabilities and escalating resource conflicts. This study underscores the need for cross-border collaboration and sustainable adaptation policies to mitigate the long-term impacts of climate change in the Middle East.

Optimal Power Flow Control In The Iraqi Power Grid Using Artificial Intelligence Algorithms For Carbon Emission Reduction, Mohammed Shakir Juber

Al-Esraa University College Journal for Engineering Sciences

Iraq’s power sector remains in a protracted and severe crisis characterized by a significant mismatch between supply and demand, high levels of losses during transmission and distribution, as well as an increasing challenge to the resources base being largely unfavourably. These inefficiencies impose heavy costs on the national economy in excess of 40 billion annually and they also reinforce greenhouse gas emissions, and exacerbate environmental issues. To deal with these problems, we proposed in this paper that a new hybrid AI tool should be developed for the solution of multi-objective optimization problem based on purpose Genetic Algorithm (GA) merger with …

Applying Machine Learning Techniques For Early Detection Of Cyber Attacks On Iot Devices, Noor Adnan Allamy

Al-Esraa University College Journal for Engineering Sciences

This research designs, implements, and evaluates a machine learning-based framework for the early detection of cyber attacks targeting Internet of Things (IoT) devices, with a specific focus on the context and challenges present in Iraq. The study conducts a comparative analysis of three supervised learning algorithms—Support Vector Machine (SVM), Random Forest (RF), and Deep Neural Networks (DNN)—using a combination of benchmark datasets (NSL-KDD, CIC-IDS-2017, Bot-IoT) and a synthesized dataset adapted to simulate the Iraqi threat landscape. Key performance metrics, including accuracy, precision, recall, and F1-score, were used for evaluation. The proposed Random Forest model demonstrated superior performance, achieving an accuracy …

Ai-Enhanced Heat Transfer Optimization In Magnetic Bio-Nanofluids, Hasan Attyah Shaboot

Al-Esraa University College Journal for Engineering Sciences

This study presents a hybrid Artificial Intelligence–Computational Fluid Dynamics (AI-CFD) framework for optimizing heat transfer in magnetic bio-nanofluids subjected to external magnetic fields. Magnetic bio-nanofluids, composed of biocompatible base fluids containing superparamagnetic nanoparticles, exhibit tunable thermal and flow behavior, making them promising for biomedical and micro-cooling applications. Conventional optimization methods based on experiments or brute-force CFD are computationally expensive and limited in exploring the full design space. To overcome these challenges, an Artificial Neural Network (ANN) surrogate model was developed to predict two key performance indicators, the Nusselt number and the friction factor, with high accuracy (R² > 0.997). The surrogate …

Hybrid Experimental–Computational Study On The Energy Absorption Of Graphene Nanoplatelet-Reinforced Sandwich Structures, Hamdan Yousif Hamdan

Al-Esraa University College Journal for Engineering Sciences

Background: Sandwich composites are widely used in aerospace, automotive, and marine applications because of their lightweight, stiffness, and strength, but they remain prone to out-of-plane impacts and barely visible impact damage (BVID). Graphene Nanoplatelets (GNPs) have shown strong potential to improve fracture toughness and impact resistance. However, hybrid experimental–computational studies applying such reinforcement are still lacking in developing contexts like Iraq, where practical and accessible solutions are essential. Aims: The study investigates the effect of GNP reinforcement on the low-velocity impact behavior and energy absorption of glass fiber/epoxy sandwich panels with PVC foam and balsa wood cores. Objectives include fabricating …

Effect Of Thick Closed Walls Of West And South Elevations Of Iraqi Middle And South Territory Housing Building On Reducing Energy Use, Abeer Qasim Jbur, Shaimaa M. Hamza, Mayyadah Lutfi Abdulwahhab

Al-Esraa University College Journal for Engineering Sciences

Thermal insulation is one of the most important factors in achieving sustainability, increasing efficiency, and reducing energy consumption, but modern insulation materials are expensive, in addition to their availability. Therefore, through our research, we resorted to investigating the issue of reducing thermal load in buildings through the use of thick-walled facades in the southern and western facades, where we studied a building with two windows with windows on the southern and western facades and another without these windows and with thick walls, for two locations, the first in central Iraq, which is the city of Baghdad, and the second in …