Materials Science and Engineering Commons^™

Research Progress In Electrodeposition Technology Of Titanium-Based Iridium Oxide Electrode, Dan-Dan Wu, Xu Wu

Journal of Electrochemistry

Titanium-based iridium oxide electrode has been widely used in various fields, such as electrocatalytic oxidation, biomedical applications, hydrometallurgical metal recovery, electro-osmotic dewatering, etc. At present, it is mainly prepared by traditional thermal decomposition method, however, which has high cost, cumbersome process, mainly relying on manual labor and cannot be mass-produced yet. It is, therefore, urgently necessary to explore new preparation technologies by focusing on electrodeposition technology, with technological characteristics such as eco-friendly and sustainable development. This article systematically discusses the research progress in iridium oxide electrodeposition preparation technology from the aspects of deposition solution formulation, base material selection and treatment, …

Preparations And Electrocatalytic Ethanol Properties Of Palladium Intercalated Hydrotalcite, Shou-Xun Hu, Liang Li, Jun-Hao Yang, Liu-Qiang Li, Zhi-Hao Jin

Journal of Electrochemistry

High-performance electrocatalysts play a vital role in the commercial application of direct fuel cells. Current anode materials still have such problems as low activity, easy poisoning and high cost. In this study, a new type of nano- palladium (Pd) catalyst was prepared by dipping method using layered double hydroxides (LDHs) as the carrier. X-ray diffractometer, scanning electron microscope (SEM), inductively coupled plasma mass spectrometer (ICP-MS), energy spectrometer, transmission electron microscope (TEM), cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscope were used to analyze the structure and electrocatalytic performance of the catalyst. The results showed that the newly prepared Pd/Mg-Al-LDHs still maintained …

Research Progress Of Sio2 Regrowth During Selective Etching Process In 3d Nand Manufacture Procedure, Zi-Han Zhou, Yun-Wen Wu, Ming Li, Su Wang

Journal of Electrochemistry

As one of the most significant memory chips in semiconductor market, NAND has been developed from two-dimension (2D) to three-dimension (3D). Due to the three-dimensional memory structure of 3D NAND, the capacity density, read-write speed and reliability of memory chips have been greatly improved, as well as the reduction of power dissipation. It is by nitride-oxide selective etching process in the alternate stacked structure of 3D NAND that the inter-dielectric layers can be obtained. The more stack layers, the better performance of chips will be. Meanwhile, however, silicon dioxide (SiO₂) would regrow on the corner of oxide layers, …

Influence Of Resveratrol On Performance Of Long-Term Storage’S Lithium-Ion Battery Electrolyte, Lei Zhang, Xu-Ping Zhang, Si-Wei Zhang, Quan-Chao Zhuang

Journal of Electrochemistry

Electrolyte of lithium-ion battery usually goes through processes of filling, transportation and storage from the completion of manufacture to the use. Understanding the influence of long-term storage process on performance of lithium-ion battery electrolyte is of theoretical significance for production of lithium-ion battery. Scanning electron microscope (SEM) images showed that the solid electrolyte interface (SEI) film formed on the surface of the graphite electrode was thicker in the base electrolyte after 6 months of storage. The charge/discharge test results showed that the reversible cycle capacity and cycle stability (capacity retention rate) of graphite electrode decreased significantly after 6 months of …

Syntheses Of Na3V2(Po4)2O2F As A Cathode For Sodium Ion Battery Application, Kai Wu

Journal of Electrochemistry

High-temperature solid-state method, hydro-thermal method and solvo-thermal method have been mainly employed to synthesize Na₃V₂(PO₄)₂O₂F (NVPF) cathode materials. However, these methods are energy consuming and complicated, which is not applicable for a large scale industrial production. In this study, a rather low-temperature (70℃) co-precipitation strategy was proposed to synthesize NVPF cathode materials. The as-prepared NVPF cathode materials showed a spherical shape with a diameter of 400 ~ 500 nm, and exhibited a sodium storage of 105.6 mAh·g^-1 and an efficiency of 90.06%. After a simple thermal process, the specific …

Doped-Magnesium Manganese Oxide Cathode For Rechargeable Magnesium Batteries, Nurhidayu Harudin

Student Works (2020-2029)

Magnesium has numerous good characteristics that make it attractive as an electrode material for rechargeable batteries. There are many advantages of Magnesium (Mg) such as available in abundance, ease of handling, low toxicity and environmental friendly. Due to its benefits, magnesium ion battery can be considered as an alternative to lithium in future. In the present work, the improvement electrochemical properties of magnesium-based cathode material, MgMn2O4 was done by adding calcium (Ca) and strontium (Sr) as dopant i.e MgMn2-xCaxO4 and MgMn2-xSrxO4. These materials with compositions of x=0.1,0.2,0.3,0.4,0.5 were synthesized by self-propagating combustion method using citric acid as a reducing agent. …

Nanoengineered Materials For Energy Conversion & Storage Applications: A Density Functional Theory Study, Ahmed Biby

Theses and Dissertations

The conventional approach for the development of novel materials has become long relative to the desired product development cycle. Thus, the sluggish pace of the development of materials within the conventional approach hinders the rapid transformation of the scientific outcomes into useful technological products. To this end, the field of hierarchical materials informatics evolved to bridge this gap. In this field, the multiscale material internal structure is considered the starting point and the core of this approach. This being said, the density functional theory (DFT) was used to generate useful materials data for the advancement of the hierarchical materials data-bases …

Synthesis And Characterization Of Perovskite-Based Materials For Memory Device Application, Gregory Thien Soon How

Student Works (2020-2029)

This project aims to study the resistive switching behaviour in memory devices using perovskites-based structures. A hybrid organic-inorganic lead halide perovskite was studied in this project, specifically methylammonium lead triiodide, CH3NH3PbI3 or MAPbI3 perovskite. The effect of the various counter electrodes in MAPbI3 perovskite was investigated by fabricating MAPbI3 perovskite on Indium Tin Oxide (ITO). Three commonly used electrodes which are Aluminium (Al), Silver (Ag), and Gold (Au) were thermally evaporated on top of the MAPbI3 perovskite layer. It was found that the ITO/MAPbI3/Al exhibits Resistive Random Access Memory (ReRAM) behaviour with SET voltage (VSET) of 4.5 V and RESET …

Valorization Of Xylan In Agroforestry Waste Streams, Harrison Appiah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Valorization of Xylan in Agroforestry Waste Streams.

Harrison Appiah

Microwave-assisted deep eutectic solvent and gamma-valerolactone metallic chloride catalyzed conversion of xylan to furfural were investigated using a 2x3 factorial experimental design at two levels of percent microwave power, reaction time, and catalyst concentration. The levels of each factor studied were (20%, 60% microwave power, 2, 4 minutes, and 10, 20mg) respectively. The effect of three metallic chloride catalysts (LiCl, FeCl3.6H20, CuCl2) on the conversion of xylan to furfural was also investigated. The gamma-valerolactone-ferric chloride sent system exhibited the highest mean yield of furfural (56.50%). The next highest furfural yield of …

Multi-Level Analysis Of Atomic Layer Deposition Barrier Coatings On Additively Manufactured Plastics For High Vacuum Applications, Nupur Bihari

Dissertations, Master's Theses and Master's Reports

While hardware innovations in micro/nano electronics and photonics are heavily patented, the rise of the open-source movement has significantly shifted focus to the importance of obtaining low-cost, functional and easily modifiable research equipment. This thesis provides a foundation of open source development of equipment to aid in the micro/nano electronics and photonics fields.

First, the massive acceptance of the open source Arduino microcontroller has aided in the development of control systems with a wide variety of uses. Here it is used for the development of an open-source dual axis gimbal system. This system is used to characterize optoelectronic properties of …

Development Of Synthetic Coal Char Simulant For Microwave Conversion Studies: A Computationally-Driven Approach, Kevin A. Hager

Graduate Theses, Dissertations, and Problem Reports (ETD)

Recent experimental demonstration of new reaction windows for coal char/methane reactions that are less energy-intensive, provides innovation for modular reactors. However, the correlation of the exact mechanism for the enhancement of these reaction windows is not certain. This study investigates the simplification of these experimental studies by developing a well-characterized coal char simulant. The approach involves using a computational approach to screen macroscopic composition to replicate the dielectric and compositional response of actual char. This study is focused on PRB coal char. A discrete element method (DEM) technique was used to simulate the packing of coal chars to give the …

In Depth Characterisation Of The Biomolecular Coronas Of Polymer Coated Inorganic Nanoparticles With Differential Centrifugal Sedimentation, André Perez-Potti, Hender Lopez, Beatriz Pelaz, Abuelmagd Abdelmonem, Mahmoud G. Soliman, Ingmar Schoen, Philip M. Kelly, Kenneth A. Dawson, Wolfgang J. Parak, Zeljka Krpetic, Marco P. Monopoli

Articles

Advances in nanofabrication methods have enabled the tailoring of new strategies towards the controlled production of nanoparticles with attractive applications in healthcare. In many cases, their characterisation remains a big challenge, particularly for small-sized functional nanoparticles of 5 nm diameter or smaller, where current particle sizing techniques struggle to provide the required sensitivity and accuracy. There is a clear need for the development of new reliable characterisation approaches for the physico-chemical characterisation of nanoparticles with significant accuracy, particularly for the analysis of the particles in the presence of complex biological fluids. Herein, we show that the Differential Centrifugal Sedimentation can …

Treated Hfo2 Based Rram Devices With Ru, Tan, Tin As Top Electrode For In-Memory Computing Hardware, Yuvraj Dineshkumar Patel

Theses

The scalability and power efficiency of the conventional CMOS technology is steadily coming to a halt due to increasing problems and challenges in fabrication technology. Many non-volatile memory devices have emerged recently to meet the scaling challenges. Memory devices such as RRAMs or ReRAM (Resistive Random-Access Memory) have proved to be a promising candidate for analog in memory computing applications related to inference and learning in artificial intelligence. A RRAM cell has a MIM (Metal insulator metal) structure that exhibits reversible resistive switching on application of positive or negative voltage. But detailed studies on the power consumption, repeatability and retention …

Effect Of 18-Crown-6 Additive On Chromium Electrodeposition In Ionic Liquid, Yi-Jie Wang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

Trivalent chromium ion (Cr³⁺) is used for electrodeposition due to its low toxicity. Electrodeposition in ionic liquids can greatly solve for hydrogen evolution problem. However,as a widely used Cr(III) precursor, chromium chloride hydrate (CrCl₃·6H₂O), still contains water. In the presence of water, Cr³⁺ will form a complex coordination structure with water molecules ([Cr(H₂O)₆]³⁺), which is a stable octahedral structure and is difficult to be directly reduced to chromium metal. Therefore, coordination agents should be added into the bath. In this work, the effect of 18-Crown-6 additive on …

Effect Of Reaction Conditions On Cu⁃Catalyzed Co2 Electroreduction, Chang Zhu, Wei Chen, Yan-Fang Song, Xiao Dong, Gui-Hua Li, Wei Wei, Yu-Han Sun

Journal of Electrochemistry

Electrochemical conversion of carbon dioxide (CO₂) driven by renewable electricity that can meet both carbon emission reduction and renewable energy utilization has been rapidly developed in recent years. Copper (Cu) catalyst has long been a promising candidate for CO₂ electroreduction applications because of its natural abundance and specific capability of producing a substantial amount of C2 products. However, various metallic Cu electrodes reported have been significantly influenced by the adsorption of certain cation/anion ions, resulting in wide-span catalytic activities and selectivity for various products. In addition, a recent report demonstrated that by virtue of gas-diffusion flow cell …

Numerical Simulations Of Current And Temperature Distribution Of Symmetrical Double-Cathode Solid Oxide Fuel Cell Stacks Based On The Theory Of Electric-Chemical-Thermal Coupling, Cheng-Rong Yu, Jian-Guo Zhu, Cong-Ying Jiang, Yu-Chen Gu, Ye-Xin Zhou, Zhuo-Bin Li, Rong-Min Wu, Zheng Zhong, Wan-Bing Guan

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) is a high-efficient clean conversion device for future energy management. Because of the low antioxidant reduction ability and complex thermal stress, the structure of traditional asymmetrical thin anode-supported planar SOFC is easily to be broken under stack operating conditions. To overcome these defects, a new complete symmetrical SOFC based on double-sided cathodes was developed. To study the influences of gas flow direction and current collection mode on the cell performance inside stack, a numerical model was established by finite element method based on the theory of electro-thermo-chemo multiphysical coupling. By applying this model, the molar …

Pitting Behaviors Of Passivated And Trans-Passivated 304 Stainless Steel, Jing Shen, Zi-Ming Wang, Da-Jiang Zheng, Guang-Ling Song

Journal of Electrochemistry

In order to further understand the passivation and trans-passivation behaviors of 304 stainless steels, the samples were pretreated under different polarization potentials and their corrosion behaviors were investigated. It was found that the pitting potential of the untreated sample was the same as that of the sample treated with 1.1 V trans-passivation potential, while the pitting potential of the sample treated with 0.5 V passivation treatment was the highest. This observation was further verified by the SKP results. According to SEM observations, the surface of the untreated sample preserved a polishing morphology, while the surface of the 0.5 V passivation …

Degradation And Thermal Characteristics Of Lini0.8Co0.15Al0.05O2/Graphite Lithium Ion Battery After Different State Of Charge Ranges Cycling, Cun Wang, Wei-Jiang Zhang, Teng-Fei He, Bo Lei, You-Jie Shi, Yao-Dong Zheng, Wei-Lin Luo, Fang-Ming Jiang

Journal of Electrochemistry

The LiNi_0.8Co_0.15Al_0.05O₂ (NCA) cathode exhibits high energy density and large reversible capacity, which plays an essential role in the field of electric vehicles (EVs). However, low capacity retention and poor thermal stability limit its application. Few literatures are found for the capacity degradation mechanism of NCA/graphite batteries at home and abroad. The different state of charge (SOC) ranges cycle degradation behaviors of 18650-type NCA/graphite (2.4 Ah) battery were studied in this paper. The SOC ranges considered were 0% ~ 20% (low), 20% ~ 70% (medium), 70% ~ 100% (high), and 0% ~ 100% …

Preparations And Sodium Storage Properties Of Ni3S2@Cnt Composite, Ming-Tao Duan, Yan-Shuang Meng, Hong-Shuai Zhang

Journal of Electrochemistry

Transition metal sulfides (TMSs)-based electrode materials with highly reversible sodium storage have attracted extensive attentions as one of the most prospective electrode materials for sodium ion batteries (SIBs). However, low cycling stability and rate property caused by large volume expansion and poor electronic conductivity during the electrochemical reaction still hamper their further practical application. In this work, in-situ encapsulated Ni₃S₂ nanoparticles in carbon nanotubes (Ni₃S₂@CNT) have been successfully fabricated as an anode material for high-performance SIBs by a one-step solid-phase calcination process. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), …

Effect Of Stereotaxically-Constructed Graphene On The Negative Electrode Performance Of Lead-Acid Batteries, Pin-Song Chen, Yi-Tao Hu, Xin-Yi Zhang, Pei-Kang Shen

Journal of Electrochemistry

With the advantages of high ratio surface area, excellent conductivity and high stability, the stereotaxically-constructed graphene (SCG) material was added to the negative active material (NAM) of lead-acid battery for improving battery performance. XRD, SEM and cyclic voltammetry tests were carried out to analyze the influence of SCG on negative active material. It is found that the conversion efficiency of lead sulfate to lead in the negative active material added with SCG material was higher than that of control group, and the particle size of the lead sulfate obtained after the discharge reaction was smaller, which are favorable factors for …

Core-Shell Structured Ru@Ptru Nanoflower Electrocatalysts Toward Alkaline Hydrogen Evolution Reaction, Xue-Liang Wang, Yuan-Yuan Cong, Chen-Xi Qiu, Sheng-Jie Wang, Jia-Qi Qin, Yu-Jiang Song

Journal of Electrochemistry

Water electrolysis for hydrogen production is beneficial for solving the problem of energy crisis and environmental issues. It is necessary to study highly active and cost-effective catalysts toward hydrogen evolution reaction (HER) to reduce the consumption of noble metals. Herein, we report the synthesis of core-shell structured Ru@Pt_0.24Ru nanoflowers electrocatalyst by stepwise reduction of Ru and Pt precursors in the mixture of oleylamine and benzyl alcohol at 160 ^oC. The average diameter of the resultant Ru@Pt_0.24Ru was 16.5±4.0 nm with a bulk atomic ratio between Pt and Ru of 0.24:1 and a surface ratio of …

Preparations And Photoelectrochemical Performances Of Rgo-Tio2 Nanotubes Arrays, Ze-Yang Zhang, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Decorating TiO₂ nanotube arrays with RGO to improve the photocatalytic activity of TiO₂ nanotube arrays has been reported. For the reported RGO-TiO₂ nanotube arrays, TiO₂ nanotube arrays were prepared by anodizing the high-purity Ti foil in an organic electrolyte for multiple-step treatments, while RGO were deposited on TiO₂ nanotube arrays by using cyclic voltammetry or other electrical reduction methods. To enhance the reduction degree and the coverage of RGO on the resultant RGO-TiO₂ nanotube arrays, in this work, the one-step electrochemical anodization in hydrofluoric acid was used to fabricate TiO₂ nanotube arrays with …

Preparation And Process Optimization Of Cathode Materials For Lithium-Sulfur Batteries, Kai Wu

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries represent promising candidates for next-generation energy storage system due to their high energy density and low material cost. However, the industrial application of Li-S batteries remains challenges because of the shuttle effect from lithium polysulfides and the lack of facial routes for Li-S battery preparation. To solve these problems, a cathode consisting of different commercial carbon materials, namely, acetylene black (SP), Ketjen Black (KB) and carbon nanotube (CNT), with sulfur (S) is prepared separately for Li-S battery. After the process of 8-h ball milling for KB/S composite, together with the polyvinyl pyrrolidone (PVP) binder, the cathode could …

Synergistic Effect Of Dissolving O2 And Wavelength On The Photo-Assisted Anodic Deposition Of Ceo2 Thin Films, Tong-Zheng Jin, Yu-Meng Yang, Sheng-Hui Fan, Guo-Ying Wei, Zhao Zhang

Journal of Electrochemistry

Cerium dioxide (CeO₂) thin films have been applied as new material in many technical fields such as solid oxide fuel cells, catalysts, UV absorbents, pharmacology, and coatings for corrosion protection of many metals and alloys. Electrodeposition is widely considered to be one of the best preparation methods for CeO₂ film. In this work, the CeO₂ films were prepared by photo-assisted anodic deposition in the bath solutions containing 0.05 mol·L^-1 cerium (III) nitrate, 0.1 mol·L^-1 ammonia acetate and 70% (V/V) ethanol onto 316L stainless steel (SS) surface. The synergistic effects of …

Preparations And Properties Of Low Cost Sulfide Solid Electrolytes Li6-XPs5-XClX, Na-Chuan Yang, Yu Wang, Yi Shuai, Kang-Hua Chen

Journal of Electrochemistry

With the shortage of energy and environmental pollution, the storage of electric energy is getting more attention all over the world. In order to improve the energy density and safety performance of batteries, uses of solid electrolyte become more and more popular. However, because the conductivity of solid electrolyte is not comparable to that of liquid electrolyte, the solid electrolyte application has certain limitations. With the efforts of researchers from various countries, there are several different solid electrolytes having better conductivity, for instance, sulfide solid electrolyte and oxide solid electrolyte. Sulfide solid electrolyte is a highly promising solid electrolyte material …

Step-By-Step Modification Of Graphite Felt Electrode For Vanadium Redox Flow Battery, Jing-Yuan Lou, Dong-Jiang You, Xue-Jing Li

Journal of Electrochemistry

As a well-known electrode material of the vanadium redox flow battery (VRFB),graphite felt electrode is the frequently-used electrode material in VRFB, and its low electrochemical activity is one of the key factors for the low power density of VRFB. In this work, we proposed a step-by-step modification method, which used KMnO₄ to oxidize graphite felt first and then placed in an activation solution to excite its reactivity, to improve the electrochemical performance of the graphite felt electrode. According to the results from cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) characterizations …

Practical Adhesion Measurements In Organic Coatings; Advancing Understanding And Mechanical Methods Development, Diana Gottschalk

Dissertations

“Adhesion” can be considered either a mechanical or chemical phenomenon. The mechanical interpretation describes the difficulty of separating surfaces and is useful for quantifying performance within applications that depend on bulk and interfacial properties. Chemical adhesion describes interfacial resistance to chemical attack and does not depend on bulk properties. Predicting chemical failure through mechanical measurement is confounded by the influence of bulk properties. However, the prospect is attractive because of the robust tolerance for sample geometries, allowing experiments to resemble an end-use system. The present work's primary goal was to elevate mechanical methods to provide a detailed interfacial characterization of …

Study On Cation Exchange Of A Lead Coordination Polymer Targeting Dynamic Mixed Cation Doped And Mixed-Valent Coordination Polymers, Hamisu Aliyu Mohammed

Student Works (2020-2029)

Solid solution in Metal-Organic Coordination Polymers (MOCPs) is an emerging synthetic pathway for modifying chemical compositions and has been expansively investigated. It has been demonstrated to be an important tool for engineering novel functional materials that otherwise have not been synthesized via the conventional technique. Although stable solid material with variable functionalities and intriguing structural motifs could be engineered by judicious selection of multivariate metal centers and multifunctional ligands. However, solid solution featuring mixed valence in MOCP is rare. Motivated by the ability of Pb2+ to adopt range of coordination numbers (CN) and chemical environments (CE), in addition to its …

Topology And Control Of Self-Assembled Domain Patterns In Low-Dimensional Ferroelectrics, Y. Nahas, S. Prohorenko, Q. Zhang, V. Govinden, N. Valanoor, L. Bellaiche

Physics Faculty Publications and Presentations

Whilst often discussed as non-trivial phases of low-dimensional ferroelectrics, modulated polar phases such as the dipolar maze and the nano-bubble state have been appraised as essentially distinct. Here we emphasize their topological nature and show that these self-patterned polar states, but also additional mesophases such as the disconnected labyrinthine phase and the mixed bimeron-skyrmion phase, can be fathomed in their plurality through the unifying canvas of phase separation kinetics. Under compressive strain, varying the control parameter, i.e., the external electric field, conditions the nonequilibrium self-assembly of domains, and bridges nucleation and spinodal decomposition via the sequential onset of topological transitions. …

Research Progress Of Sulfur Cathode Catalytic Conversions For Lithium-Sulfur Batteries, Qin-Jun Shao, Jian Chen

Journal of Electrochemistry

The electrochemical reduction of sulfur (S) takes place through multistep reactions when S is used as a cathode material. The complete discharge of S to form final product lithium sulfide (Li₂S) is a two-electron reaction. The formation of low-order lithium polysulfides (LiPS) needs to overcome certain energy barriers. And the reduction of Li₂S₂ to Li₂S is the rate-limited step. The reaction kinetic of sulfur cathode is the critical key to determine the electrochemical performance of Li-S batteries, such as specific energy, specific power and low temperature performance, etc. Accelerating the rate-limited step kinetics …