Materials Science and Engineering Commons^™

Laser Scanning In-Situ Photoelectrochemical Microscopictechnique And Its Applications, Zugeng Lin, Jinkua You, Xiangdong Zhuo, Chun Zhang, Yong Yang

Journal of Electrochemistry

The main factors of the laser scanning in-situ photoelectrochemical microscopic measurement system which is set up in our lab have been discusaed in this paper. Some applications of this technique for in-situ study of modification and processing of semiconductor electrodes, monitoring of electro deposition process of semiconducting material and redox reaction occurring at metal oxide electrodes have also been presented. The results have shown that the technique is very powerful that for studing local photoelectrochemical properties of semiconductors and metal oxide electrodes. These provide important information on the micro structural and electronic properties in the solid/electrolyte interface.

Studies On Low Temperature Performance Of Rechargeable Mh-Ni Batteries, Wenkuan Zhang, Jingxian Shi, Yuwan Lou, Qiusheng Duan

Journal of Electrochemistry

The Dependence of low temperature performance on the alloy composition and electrolyte component for rechargeable MH-Ni batteries is studied, the suitable composition of alloy and electrofyte are founds.

An Indirect Electrochemical Oxidation Of Toluene──Anodic Oxidation Of Mn(Ⅱ) On The Lead Electrode, Zhonghua Wang, Qingmin Hua, Guacai Chen, Zhongquan Wang, Yunan Qiu, Xingguo Yan

Journal of Electrochemistry

The electrochemical oxidation of Mn(Ⅱ) to Mn(Ⅱ) in concentrated H₂SO₄ (2 ~ 8 mol⋅L^-1) at lead electrode has been studied. It is found that the electrode surface is oxidized to PbO₂ in a direct electrochemical reaction, then PbO₂ formed reacts with Mn(Ⅱ) in a chemical reaction. Some effects involves current density, concentration of H₂SO₄, temperature and conversionwere evaluated. The rule of electrogenerated Mn(Ⅲ) in flow electrolysis cell were determined at several conditions. The current efficiency at greater than 90% is obtained in general.

Electrochemically Modified Glassy Carbon Electrode And Determination Of Copper By Anodic Stripping Voltammetry, Jinrui Xu, Yie Liu, Xiurun Zhuang, Tomoo Miwa, Toyohide Takeuchi

Journal of Electrochemistry

This paper reported the glassy carbon electrode modified by cyclic voltammetrybetween -0.1 and +1.5 V (vs. SCE) in an aqueous solution containing catechol, for maldehyde and talium hydroxide. The modified electrode can be applied to the determination of copper(Ⅱ) in water, and its sensitivity is about 35 times higher than that of unmedified glassy carbon electrode, The quantitative limit with this modified electrode is 0.1 ng/ml.

Photoelectrochemical And Spectroelectrochemical Studies Oniron Oxide Ultrafine Particles, Maizhi Yang, Yongjun Ji, Wen Zhang, Shengmin Cai, Xiaojiang Lu, Zhongqun Tian, Jin Luo

Journal of Electrochemistry

In this paper, Raman spectra, photocurrent and the UV-VIS reflectance aremeasured for studying the α-Fe₂O₃ ultrafine particles adsorbed on Pt electrode. The blue shifts of Raman peaks demonstrate the size quantization effect for the particles of 50 nm in diameter ascompared with the bulk material. With the changing of the potential, the photocurrent decrcases as the UV-VIS reflectance increases, and vice-versa. Therefore, the potential not only affects the hargetransfer direcdtion in the interface of electrode/redox couple, but also influences the light absortion onthe surface of particles. According to the results of photoelectrochemistry, we suggest that the cathodic …

Horseradish Peroxidase/Poly-O-Phen Ylenediamine Mem Brane Electrode: Preparation And Properties, Dong Wei, Huihuang Wu

Journal of Electrochemistry

A horseradish peroxidase (HRP)/poly-o-phenylenediamine (PPD) membrane electrode was prepared by electropolymerization of o-phenylenediamine on glassy carbon in pH 7.0 phosphate buffer, the process of the enzyme immobilization was studied. The enzyme electrode obtained exhibits the activity to catalyze the electroreduction of hydrogen peroxide in the absence of any electron transfer mediator. The red uction reaction occurs in the potential range of PPD redoxprocess, it was believed that the polymer participates in electron transfer of the enzyme. The enzyme reaction kinetics at rotating HRP/PPD electrode was analysed, and the factors influencing kinetic parameters were discussed.

The Electrochemical Reduction Of 2-Ethylanthraquinone (2eaq), Yaobin Zhu

Journal of Electrochemistry

The process of electrochemical reduction of 2EAQ in DMSO is studied using CVand ESR methods in this work, Pt, Pd and some implanted materials are used as electrodes. The quasi-rever-sible property of two electron transfer steps and their following homogeneous chemical reactions are illustrated. The mechanism of the electrochemical red uction of 2EAQ and the kinetic parameters of the related steps are obtained. Having measured the influence of water content in the system, the effect of the proton donor is discussed. After comparising the experimental results with each other these experiments gives us the idea that the replacement of metal …

The Reduction Of Oxygen To Hydrogen Peroxide At The Poly(O-Phenylenediamine)-Filmed Electrode, Zhaoe Lu, Tiangeng Zhong, Guanyong Zhang

Journal of Electrochemistry

The poly(o-phenylenediamine) (PPD) filmed graphite electrode was formed by electro-polymerization of o-phenylenediamine in acidified (pH=1) 0.2 mol·L^-1 Na₂SO₄ solution using the cyclic voltammetric methed. The catalytic effect of the electrcareduction of oxygen in acid olution was demonstrated by the voltammogram of the electrode in the oxygen saturated acid solutionof Na₂SO₄. The current efficiency of the reduction of oxygen to hydrogen peroxide was determined by the electrolysis in a divided cell under the condition of constant current. The various effectsinfluencing the accmulation of H₂O₂ in the catholyte were discussed.

Studies On Coordination Behavior Of Dimethyl Sulfoxide In Complex Of Rare Earth With Cryptand, Shichang Liu, Tianpei Zhu

Journal of Electrochemistry

Electrochemical reduction reaction in the course of the titration of Eu(2.2.2) and Eu(2.2) using strong bonding solvent, DMSO, in C₂H₄Cl₂ has been investigated by cyclic voltammetry. The greater the concentration of strong bonding solvent, the more negative the half-wave potentials for the reduction reaction are. The coordination number of Eu(2.2.2) and Eu(2.2) which are 2 and 3 respectively, with DMSO can be calculated, according to the relations between half-wave potentials and the variety of concentration of DMSO.

An Investigation Of Hole Size Effects In A Composite Material During Tensile Fracture, David Floyd Moore

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental investigation was conducted to evaluate the hole size effects, i.e., the reduction in strength with an increase in hole size at a constant stress concentration factor, for a glass fiber reinforced epoxy crossply laminate during tensile fracture. The characteristic dimension according to the point-stress and average-stress criteria of the two-parameter models proposed by Whitney and Nuismer were determined and compared for a circular hole, optimized circular hole, square hole with radiused corners and square hole with sharp corners. Modified versions of the two-parameter models proposed by Karlak and Pipes, Wetherhold, and Gillespie were also compared. On the basis …

Studies Of Elecctrochcmical Oscillation Of Au/Hcl In Presence Of ″Positive Feedback″Of Substrate Electrodes, Bin Ren, Bingwei Mao, Xiongwei Cai, Tao Jiang, Jiqian Mu

Journal of Electrochemistry

/

A Photoelectrochemical Investigation Of Zirconium Oxide Film, Maizhi Yang, Ping Wei, Di Quarto F., Piazza S., Sunseri C.

Journal of Electrochemistry

A photoelectrochemical investigation has been carried out on zirconium initialoxide film and its oxide film grownanodically at constant rate up to different thickness. Both anodicand cathedic photocurrents on the photocurrent spectrum depended on the potential, but had littlerelation with the forming anedic films or measuring solutions. Photocurrent spectrum and photocurrenttransients suggested that the oxide films on zirconium were duplex layers structure. The internal layerwas ZrO₂ and the external layer ZrO₂·(H₂O)_n. The photocurrent included photogenerated carrier ininternal and external oxide films, as well as internal photoinjection process for electrons from thesubstrate metal into the …

Application Of Inhibitor To Improve The Anticorrosion Performance Of Electrophoretic Coating, Changshou Cai, Fangteng Su, Bihuan Liu, Guomou Wen, Jingdong Guo, Renxin Liu, Weidong Tian

Journal of Electrochemistry

To improve the anti-corrosion performance of electrocoating, organic andinorganic inhibitors are applied in an anodic electrophoretic-coating. The results show that the deposition of polymer with zinc phospate exhibits a high inbihition efficiency. The inhibition mechanism of the inhibitor in electrocoating has been studied.

A Investigation Of Hydrogen-Storage Alloy As Catalytic Electrode For Hydrogenation Of Nitrobenzene, Shigang Lu, Hanxi Yang, Changfa Wan

Journal of Electrochemistry

Since hydrogen-storage alloy ean not only absorb hydrogen atoms to form highlyreactive metal hydride as hydrogen source by electrolysis but also possesses a certain catalytic activityfor hydrogenation,it is thus feasible to utilize the allov as a novel electrode for electrolvtichydrogenation in organic electroreduction. This work employed misch metal AB₅ type alloy as acatalytic electrode and studied the electrochemical hydrogenation of nitrobenzene.

The hydrogen-storage electrode (MH) was a plastic bonded electrode sheet made from a paste of Mm(NiCoMnAl)₅ alloy powder and teflon emulsion. The electrolysis was performed at constantcurrent and controlled potential in a three electrode cell of H-type …

Transient Photocurrent Behavior Of Multiple Quantum Well Gaas/AlXGa(1-X)As Electrode, Liu Yao, Xurui Xiao, Yuan Lin, Yiping Zeng, Dianzhao Sun, Haiqun Zheng

Journal of Electrochemistry

Transient photocurrents induced by short light pulses at lattice-matched multiplequantum well (MQW)GaAs/Al_0.3)Ga_0.7 As electrodes were studied in the 1 ×10^-2 mol·dm^-3 ferrocene([Fc⁰]/[Fc⁺]=9/1)-0.1 mol·dm^-3 tetrabutylammonium tetrafluoroborate acetonitrile solutionin order to examine the relaxation photoprocesses and to evaluate kinetic parameters of superlattice electrodes.

GaAs/Al_0.3Ca_0.7 As MQW electrode consisting of 10 periods with each of GaAs well (5.3 nm) and Al_0.3Ga_0.7. As barrier (10 nm) showed two pronounced and well-resolved peak structures located at 1.503 eV and 1.699 eV in the photocurrent spectrum, corresponding to the …

Synthesis Of LiXCoo2 And Its Behaviour In Rechargeable Lithium Battery, Mingfeng Guo, Ruimin Yang, Zebo Zhang, Jincao Ye

Journal of Electrochemistry

The Variations of crystal lattice parameters of Li_xCoO₂ during charge anddischarge have been st ud ied by XRD and AAR spectroscopy. It was found that the Li_xCoO₂ crystalvolume expanded during charge and contracted during discharge. The crystal lattice structure was broken because of the formation of Co₃O₄ when deeply charge.The variation of lattice parameter C₀ value in cycling process was similar to that in charge process.The variation of 006 peak was the mostsensitive in every case. In case of preheating for 20 hours at 700℃ before operating high temperature, the …

Self Assembly Via Layer By Layer Surface Reaction On Gold Electrodes And The Electrochcmical Characterization, Xiandui Dong, Juntao Lu, Chuanxin Cha

Journal of Electrochemistry

The self-assembled monolayers,which were built by spontaneous adsorption of ω-carboxylic acid thiols on gold surface,were used as substrate for further modification through later bylayer amide surface reactions. At each stage of modification,the gold surface was characterizedelectochemieally. The results demonstrated that the strategies of layer by layer self assembly is ofsignificant potential for fabrieating functionalized ultrathin layers.

Electroreduction Of The Nittobenzene On Titanium Electrode Implanted With Palladium, Zhongda Wu, Xianjun Zhu, Hongsen Wang

Journal of Electrochemistry

The titanium substrates were bombarded with 1×10¹⁷～5×10¹⁷ ions·cm^-2 ofpalladium at the room temperature. The surface composition of implanted electrode and concentration-depth profiles of various elements were measured by AES. The electrored uction processes ofnitrobenzene (NB) in 0.1 mol/L NaOH solution at Pd/Ti electrodes have been investigated by cyclicvoltaivimetry. The results show that the palladium implanted titanium electrodes exhibit a high catalyticactivity in the electroreduction of NB. The NB radical anion, which is the product of one-electronelectroreduction of NB, was detected by ESR in-situ in conjunction with electrochemical methods. Aniline was also detected as a product of …

Electroreduction Of Holmium Ion On Iron Electrde In Molten Cholorides, Qiqin Yang, Guankun Liu, Yuzhi Su

Journal of Electrochemistry

The cyclic voltammetry, open circuit potential-time curve after poteritiostatic electrolysis, current-time curve at potential step, X-ray diffraction and electron probe microanalysiswere used to investigate the electrode process of Ho(Ⅲ) reduced on iron electrode in molten chloridesand the phases of surface alloy layer. The Ho-Fe alloys are formed at first, and then the metallic holmium is deposited when Ho(Ⅲ) is reduced on iron electrode. The charge transfer is reversible. The free energies of formation for the four inter metallic compounds of Ho-Fe system, the diffusion coefficients and diffusion activation energy of Ho in alloyed cathode are determined.

The Study Of The Growth Processes Of The Oxides On Lead Electrodes In Sulfuric Acid Solution, Hesheng Zhai, Xuguang Chen, Jinkua You, Yong Yang, Zugeng Lin

Journal of Electrochemistry

The growth processes of PbO and PbO₂ on lead electrodes have been investigatedby using in-situ methods that are combined with temporary AC resistance measurment technique and in-situ laser scanning photoelectrochemical microscopy. It is found that a linear relationship existsbetween the electrode resistance(R) and^1/2 after the electrode is oxidized at +0.6 V(vs.Hg/H₂SO₄/35% H₂SO₄) for more than 5 min. This result suggests that the growth of PbO is well distributed during the early stage of oxidation. The study by using laser scanning photoelectrochemical microscopy has further proved this point. The results also …

The Electrode Process Of Y(Ⅲ) On Copper Electrode And Its Surface Metallizing, Chungen Zhou, Shuzhen Duan

Journal of Electrochemistry

The reduction of yttrium ion on copper electrode in NaCl-KCl-YCl₃ molten saltshas been investigated. The results indicate that the formation of intermetallic compounds is occuredbefore the metallic yttrium to be formed. The formation of intermetallic compounds is controlled bythe process of which yttrium atoms are diffusing into copper electrode. The kinetic characters todiffusion of yttrium atoms were also discussed.

The Catalytic Behavior For Ni-W Electrode Modified By Carbon Ion Beam Implantion, Jishuang Zhang, Yaojiao Lv, Qinglian Li, Baoen Shen

Journal of Electrochemistry

The hydrogen evolution activity in acidic and basic mediums for Ni-W electrodemodified by carbon ion bean implantation was investigated. The experimental results show thiselectrode has superior catalytic activity for the hydrogen evolution reaction than that of the unmodified Ni-electrode. Long period testing of electrolysis under high current density show that this electrode hasalonger useful life hence it is a practical electrode material. The temperature effect of electrocatalytic property was also inverstigated. The experimental regularities are explained on the basis of the formation of surface multialloys of Ni-W-WC.

Electrocatalytic Oxidation Of Formaidehyde And Formic Acid On A Pt/SbAd Electrode, Hong Li, Lincai Jiang, Xiong Jiang

Journal of Electrochemistry

The electrocatalytic activity for the oxidation of formaldehyde and formic acid ona Sb-modified platinum (Pt/Sb_ad) was investigated. Results showed that the Pt/Sb_ad electrode was electrocatalytically more active than a Pt electrode in the anodic oxidation of formaldehyde and formicacid. In the case of formaldehyde, an oxidation peak appeared at a potential of ca. 0.7V. During the oxidation of formic acid, a 4-fold increase in the 1st peak current was observed. The Sb-modified platinum electrode was found to be most electrocatalytically active at a coverage of 0.75±0.05. The electrocatalytic activity of the Pt/Sb_ad electrode can be best …

The Effect Of Some Ions On Cr2O72- Anodic Formation Process At Pt And Pbo2 Electrodes, Shixiong Jin, Zhigang Zhou, Lan Wang

Journal of Electrochemistry

The influence of Ag₂SO₄, Li₂SO₄, Na₂SO₄, K₂SO₄, (NH₄)₂SO₄,MgSO₄ and KF on the evolution of O₂ and the formation of Cr₂O at Pt and PbO₂ anodes was investigated in mixed H₂SO₄-Cr₂(SO₂)₃ solutions. The kinetic data related respectively to Cr₂O formation and O₂ evolution at Pt and PbO₂ anodes were measured by method of resolving the steady-state polarization curve. The Tafel slope …

Development Of Nial-Based Intermetallic Alloys: Effect Of Chromium Addition, R. Tiwari, Surendra N. Tewari, R. Asthana, A. Garg

Chemical & Biomedical Engineering Faculty Publications

The mechanical behavior of dual-phase NiAl(Cr) microstructures, consisting of elongated primary NiAl grains aligned with an intergranular NiAl-Cr eutectic phase, produced by extrusion of a cast NiAl(Cr) alloy, has been examined. Chromium addition to create a dual phase NiAl-based aligned microstructure leads to large increases in the yield strength but no significant toughness improvement. This is achieved primarily by solid solution hardening and precipitation hardening. The constitutional hardening rate resulting from deviations from stoichiometry in the nickel-rich NiAl was estimated to be about 66 MPa per atomic per cent of nickel.

Nonlinear Finite Element Micromechanic Analysis Of Thermoplastic Composite Of Recycled High Density Polyethylene Reinforced With Short Glass Fibers, Qiming Lou

Masters Theses

This thesis studied the nonlinear micromechanic behavior of thermoplastic composite of recycled high density polyethylene (HDPE) reinforced with short glass fibers using finite element method. The composite material was modeled using a micromechanic unit cell to simulate the stress distribution between the plastic matrix and the fiber in the composite. Nonlinear behavior of recycled HDPE and imperfect bonding between the fiber and matrix were investigated. Load-bearing capability of the fiber was evaluated using stress partition ratio (SPR) in the composite models. The effect of fiber aspect ratio on the stress distribution of the composite was studied to optimize the material …

Investigation Into The Behavior Of Geometrically Nonlinear Composite Arches, John C. Bailey

Theses and Dissertations

This research modifies the existing finite element formulation of a potential energy based large deformation and moderate rotation theory. Hermitian shape functions replace the existing linear bending angle interpolations. Negligible differences between the two formulations indicate the underlying kinematics limit the accuracy, not the finite element interpolations. Using the new program, numerous nonlinear arch geometries are modeled to investigate the effects of arc length and thickness variations. Local and global snapping phenomena are captured as well as through the thickness shear driven nonlinearities.

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite Subjected To Tension-Tension Cycling With Hold Time, Scott A. Grant

Theses and Dissertations

This study was carried out to investigate the elevated temperature behavior of the SiC-MAS5 cross- ply [0-90]_4S ceramic matrix composite manufactured by Corning Inc. to fatigue with loading waveforms that combine the characteristics of stress rupture and high cycle fatigue. The test results were compiled in the form of S-N (cycles to failure), S-T (exposure time versus cycles to failure), S-S (energy exposure versus cycles to failure), normalized modulus degradation, strain progression, and hysteresis loop progression. From the mechanical behavior demonstrated by these curves, relationships between the effect of the environment and loading waveform were developed. In addition, a …

Characterization Of Fatigue Behavior Of 2-D Woven Fabric Reinforced Ceramic Matrix Composite At Elevated Temperature, Daniel J. Groner

Theses and Dissertations

This study investigated the fatigue behavior and associated damage mechanisms in notched and unnotched enhanced Sic-SiC ceramic matrix composite specimens at 1100°C. Stiffness degradation, strain variation, and hysteresis were evaluated to characterize material behavior. Microscopic examination was performed to characterize damage mechanisms. During high cycle-low stress fatigue tests, far less fiber-matrix interface debond was evident than in low cycle-high stress fatigue tests. Notched specimens exhibited minimal stress concentration during monotonic tensile testing and minimal notch sensitivity during fatigue testing. Damage mechanisms were also similar to unnotched.

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite At Elevated Temperature Under Tension-Tension Loading, Craig D. Steiner

Theses and Dissertations

This study investigated the fatigue behavior and damage mechanisms of a [0-90]_4s SiC-MAS ceramic matrix composite under tension-tension loading at two elevated temperatures and two frequencies. Stress and strain hystereses, maximum and minimum strain, and modulus of elasticity were evaluated to characterize the material behavior. Microscopy and fractography were used to evaluate damage progression and mechanisms. Fatigue life was independent of frequency at both temperatures.