Materials Science and Engineering Commons^™

Processing, Microstructure, And Mechanical Properties Of Zirconium Diboride-Molybdenum Disilicide Ceramics And Dual Composite Architectures, Ryan Joseph Grohsmeyer

Doctoral Dissertations

"This research had two objectives: characterization of processing-microstructure-mechanical property relationships of conventional ZrB₂-MoSi₂ ceramics at room temperature (RT) and 1500⁰C in air, and fabrication of ZrB₂-MoSi₂ dual composite architectures (DCAs) for use near 1500⁰C. Elastic moduli, fracture toughness, and flexure strength were measured at RT and 1500⁰C for 15 ZrB₂-MoSi₂ ceramics hot pressed using fine, medium, or coarse ZrB₂ starting powder with 5-70 vol.% MoSi₂, referred to as FX, MX, and CX respectively where X is the nominal MoSi₂ content. MoSi₂ decomposed during sintering, resulting in …

Preface-Jes Focus Issue On Electrolysis For Increased Renewable Energy Penetration, B. Pivovar, M. Carmo, K. Ayers, X. Zhang, J. O'Brien

Mechanical & Aerospace Engineering Faculty Publications

(First paragraph) Today represents a particularly exciting time, as our planet’s energy system is undergoing major changes due to dramatically decreasing renewable energy prices and increasing societal concerns over greenhouse gas emissions, criteria pollutants (arsenic, mercury, NOx, particulate matter), and climate change. These factors are pushing society toward deep decarbonization of our energy system, perhaps the most challenging issue facing the planet today. Unfortunately, wind and solar energy, while both promising generation sources, come with intermittency challenges and have limitations in their abilities to impact industrial and transportation sector demands where fossil fuel energy carriers based on chemical bonds have …

Power Maximization For Pyroelectric, Piezoelectric, And Hybrid Energy Harvesting, Murtadha A. Shaheen

Theses and Dissertations

The goal of this dissertation consists of improving the efficiency of energy harvesting using pyroelectric and piezoelectric materials in a system by the proper characterization of electrical parameters, widening frequency, and coupling of both effects with the appropriate parameters.

A new simple stand-alone method of characterizing the impedance of a pyroelectric cell has been demonstrated. This method utilizes a Pyroelectric single pole low pass filter technique, PSLPF. Utilizing the properties of a PSLPF, where a known input voltage is applied and capacitance C_p and resistance R_p can be calculated at a frequency of 1 mHz to 1 Hz. …

Design For Fractal Grid Generated Turbulence, Moira Gion

Undergraduate Research & Mentoring Program

Fractal geometry can be used to find organization or order in something that appears to be in disorder, or chaos. Turbulence is viewed as one place where fractal geometry can be found in nature. The irregularity in fluid flow is dependent on the initial conditions. In the past, the idea of self-similarity has been used to develop statistical theories of energy cascade in a turbulent flow. Recent studies have done experiments on obstructing flows with fractal objects to observe intermittency, (or self-similarity) within a turbulent flow. Experiments on fractal grid generated turbulence has been performed by other research groups, so …

Fracture Mechanics-Based Simulation Of Pv Module Delamination, Dominic I. Jarecki, Johanna B. Palsdottir, Peter Bermel, Marisol Koslowski

The Summer Undergraduate Research Fellowship (SURF) Symposium

Photovoltaic (PV) cells are rapidly growing as a renewable alternative to fossil fuels like coal, oil, and natural gas. However, greater adoption has also reduced government subsidies, placing the onus of making solar panels economically competitive on innovative research. While multiple methods have been considered for reducing costs, with each reduction in cost comes the associated peril of reduction in quality and useful lifetime. Several problems considered solved have now resurfaced as potential failure mechanisms with the introduction of cheaper PV cell technologies. However, to remain economically viable, PV modules will not only have to become cheaper, they will have …

Triboelectric Solar Generator Concept And Experimental Research, Elias Yazdanshenas

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, a novel concept, a triboelectric solar generator (TSG ), is proposed for generation of high voltage direct current (HVDC) electricity from solar radiation. An experimental investigation was conducted to prove the concepts of charge generation through the triboelectric effect and charge transmission using semiconductors. The triboelectric effect, also known as the contact electrification, is a well-known physical phenomenon that electrostatic charges are generated by rubbing dissimilar materials. However, traditional triboelectric generators had never been commercialized due to their poor power output. Physically, it is due to the difficulty of charge transmission from insulators, which generate charges. The …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Hydraulic And Thermal Performances Of A High Temperature Ceramic Plate-Fin Heat Exchanger (Pfhe), Vijaisri Nagarajan, Yitung Chen, Qiuwang Wang, Ting Ma

College of Engineering: Graduate Celebration Programs

• Numerical analysis was carried for novel configuration of high temperature PFHE
• Fluid flow and heat transfer properties were studied for various fin configurations
• Ripsaw fin design with thickness of 0.05 mm gives maximum heat transfer with less pressure drop and friction factor
• Validation and parametric study were carried out for all fin configurations

Transient And Quasi-Steady Thermal Behaviour Of A Building Envelope Due To Retrofitted Cavity Wall And Ceiling Insulation, Aimee Byrne, Gerard Byrne, Anna Davies, Anthony Robinson

Articles

Accurate understanding of the thermal behaviour of building components is essential for predicting heat-ing or cooling needs and facilitates the implementation of more successful energy saving strategies and retrofits. This paper focuses on a specific measure commonly introduced through the residential energy efficiency retrofit programmes in Ireland–insulation. Traditionally, assessments of the performance of building envelopes have been based on assumed thermal resistances of the materials involved, labora-tory tests and computer modelling. The aim of the present work is to investigate the in situ thermal behaviour of a case study building and its components under transient and quasi-steady environmental conditions, comparing …

Synthesis And Characterization Of Aluminum Doped Zinc Oxide Nanowires For Photovoltaic Devices And Semiconductors, Travis J. Wilson^, Md. Ashiqur R. Khan, Mohammad A. I. Shuvo, Miguel Mendoza, Matthew Garcia, Yirong Lin*, Chintalapalle V. Ramana*

COURI Symposium Abstracts, Spring 2012

No abstract provided.

Numerical Simulation Of Natural Convection In Rectangular Enclosures Of Varying Aspect Ratios And Its Feasibility In Environmental Impact Management Studies, Charles R. Walker

College of Graduate Studies: Theses & Dissertations

Author's abstract: Numerical simulation was used to investigate natural convection in horizontal and vertical enclosures with and without an internal heat source. Natural convection in rectangular enclosures is found in many real-world applications. Included in these applications are the energy efficient design of buildings, operation and safety of nuclear reactors, solar collector design, passive energy storage, heat transfer across multi-pane windows, thermo-electric refrigeration and heating devices, and the design-for-mitigation of optical distortion in large-scale laser systems. Considering all these applications, especially controlling heat transfer in nuclear power plants, knowledge and research results of natural convection in enclosure play a vital …

Evaluation Of Cathode Materials For Low Temperature (500-700c) Solid Oxide Fuel Cells, Alexander M. Lassman

Master's Theses

Solid oxide fuel cells (SOFC) have gained a great deal of interest, due to their potential for high efficiency power generation and ability to utilize hydrogen fuel, as well as various hydrocarbon-based fuels. A recent trend in SOFC development has been towards lower operating temperatures (500-700°C), which can substantially reduce the cost and complexity of the system. This thesis presents an investigation into state of the art Ba- and La- based cathode materials for use in low temperature (500-700°C) solid oxide fuel cells.

Synthesis of A-site deficient [A=0.97] Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃ (BSCF) was …

Phase Change Materials As A Thermal Storage Device For Passive Houses, Kevin Ryan Campbell

Dissertations and Theses

This study describes a simulation-based approach for informing the incorporation of Phase Change Materials (PCMs) in buildings designed to the "Passive House" standard. PCMs provide a minimally invasive method of adding thermal mass to a building, thus mitigating overheating events. Phase change transition temperature, quantity, and location of PCM were all considered while incrementally adding PCM to Passive House simulation models in multiple climate zones across the United States. Whole building energy simulations were performed using EnergyPlus from the US Department of Energy. A prototypical Passive House with a 1500 Watt electric heater and no mechanical cooling was modeled. The …

A Feasibility Study Of Model-Based Natural Ventilation Control In A Midrise Student Dormitory Building, Steven James Gross

Dissertations and Theses

Past research has shown that natural ventilation can be used to satisfy upwards of 98% of the yearly cooling demand when utilized in the appropriate climate zone. Yet widespread implementation of natural ventilation has been limited in practice. This delay in market adoption is mainly due to lack of effective and reliable control. Historically, control of natural ventilation was left to the occupant (i.e. they are responsible for opening and closing their windows) because occupants are more readily satisfied when given control of the indoor environment. This strategy has been shown to be effective during summer months, but can lead …

Design And Development Of Rapid Battery Exchange Systems For Electric Vehicles To Be Used As Efficient Student Transportation, Jonathan A. Bevier

Master's Theses

Rapid battery exchange systems were built for an electric van and pedal assist electric bike as a method of eliminating the need to recharge the vehicles batteries in order to increase the feasibility of using electric propulsion as a method of efficient student transportation. After selecting proper materials it was found that the systems would need a protective coating to ensure consistent operation. 1020 cold rolled steel samples coated with multiple thicknesses of vinyl resin paint, epoxy resin paint, and powder coating were subjected to environmental wear tests in order to determine if the type and thickness of common protective …

Mechanics Of Composite Materials In Fuel Cell Systems, Kenneth Reifsnider, Xinyu Huang, G. Ju, Matthew Feshler, K. An

Faculty Publications

The science and technology that are fundamental to the concept of composite materials are also the foundation for the construction and function of fuel cells and fuel cell systems. The present paper outlines this relationship in the context of the physics and chemistry that are enabled by the specific selection and arrangement of constituents of the “functional composite” fuel cell. General principles of operation are described, and fundamental issues are defined that must be addressed by the composites community if the fuel cell science and engineering is to advance. Examples of several types of functional composite fuel cells are presented, …

Thermal Assessment Of Silicon-Based Composite Materials Used In Photovoltaics, Pavlos K. Bataglannis

Theses

Photovoltaics are devices that convert sunlight directly to electricity. It is well established that the conversion efficiency of mono and poly-crystalline silicon-based photovoltaic modules is inversely related to their temperature. Substantial improvements in operational performance can thus be achieved if the thermal energy accumulating in the material can be effectively dissipated.

Accurate modelling of modules would allow possible methods of thermal dissipation to be evaluated, and as a crucial component of the model, the thermal properties of the constituent materials of PV modules needed to be known. Special consideration needed to be given to the interfaces between dissimilar materials and …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Kentucky Building Code 1980, Kentucky Library Research Collections

Research Collections

Kentucky Building Code (KBC) is the official referenced standards to ensure that a building is constructed in accordance with the approved construction documents.