Materials Science and Engineering Commons^™

A Study On The Impact Of Silicon And Manganese On Peritectic Behavior In Low Alloy Steels Assisted By Mold Thermal Mapping Technology And Shell Growth Measurements, Damilola Balogun, Muhammad Roman, Rex E. Gerald, Laura Bartlett, Jie Huang, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Non-Uniform Shell Growth Commonly Caused by the Peritectic Transformation in Low Carbon and Low Alloy Steels Has Been Directly Correlated with Mold Thermal Maps using a Mold Immersion Test into a Molten Steel Alloy. Mold Thermal Maps Were Obtained by Performing Real-Time Temperature Measurements with Optical Fibers Embedded 1 Mm from the Mold Working Surface. Shell Growth Measurements Were Obtained by 3D Optical Scanning of the Recovered Steel Shell Following Immersion Testing. the Effects of Silicon and Manganese on the Shell Growth and Mold Temperature Maps Have Been Examined in Relation to the Peritectic Transformation for Varying Carbon Contents. Results …

Real-Time Air Gap And Thickness Measurement Of Continuous Caster Mold Flux By Extrinsic Fabry-Perot Interferometer, Abhishek Prakash Hungund, Hanok Tekle, Bohong Zhang, Ronald J. O'Malley, Jeffrey D. Smith, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

Mold Flux plays a critical role in continuous casting of steel. Along with many other functions, the mold flux in the gap between the solidifying steel shell and the mold serves as a medium for controlling heat transfer and as a barrier to prevent shell sticking to the mold. This manuscript introduces a novel method of monitoring the structural features of a mold flux film in real-time in a simulated mold gap. A 3-part stainless-steel mold was designed with a 2 mm, 4 mm and, 6 mm step profile to contain mold flux films of varying thickness. An Extrinsic Fabry-Perot …

Carrier Transport Engineering In Wide Bandgap Semiconductors For Photonic And Memory Device Applications, Ravi Teja Velpula

Dissertations

Wide bandgap (WBG) semiconductors play a crucial role in the current solid-state lighting technology. The AlGaN compound semiconductor is widely used for ultraviolet (UV) light-emitting diodes (LEDs), however, the efficiency of these LEDs is largely in a single-digit percentage range due to several factors. Until recently, AlInN alloy has been relatively unexplored, though it holds potential for light-emitters operating in the visible and UV regions. In this dissertation, the first axial AlInN core-shell nanowire UV LEDs operating in the UV-A and UV-B regions with an internal quantum efficiency (IQE) of 52% are demonstrated. Moreover, the light extraction efficiency of this …

Damage Stability Study Of A 500 Dw Ro-Ro Ferry Vessel, Zulfaidah Ariany, Budhi Santoso, Sarwoko Sarwoko, Nauval Abdurrahman Prasetyo

Makara Journal of Technology

The development of the crossing transportation industry is currently increasing in the island areas. The use of Ro-Ro type ferry boats is extremely efficient in moving people, goods, and vehicles. The current research focuses on the damage stability of the 500 DWT Ro-Ro ferry, which aims to meet the needs of the Ro-Ro ferry in the archipelago area. The previously existing initial design of a barge hull with a main size Lpp = 40.15 m, B = 12 m, H = 3.2 m, and T = 2.15 m was used to analyze the damage stability condition further. First, the drawings …

Advances On Composite Cathodes For Lithium-Sulfur Batteries, Xi-Yao Li, Chang-Xin Zhao, Bo-Quan Li, Jia-Qi Huang, Qiang Zhang

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries are deemed as high-promising next-generation energy storage technique due to their ultrahigh theoretical energy density, where the sulfur cathodes with high specific capacity guarantee the energy density advantage and directly determine the battery performances. After decades of exploration, the most promising sulfur cathodes are sulfur/carbon composite (S/C) cathodes and sulfurized polyacrylonitrile (SPAN) cathodes. In this manuscript, recent advances on S/C and SPAN cathodes in Li-S batteries are comprehensively reviewed. The electrochemical reaction circumstances on S/C and SPAN cathodes are firstly introduced and compared to reveal the working mechanisms of the two types of Li-S batteries. The S/C …

Preparation Of Highly-Cyclized Sulfurized Polyacrylonitrile For Lithium-Sulfur Batteries, Xuan Ji, Jia-Yu Wang, An-Bang Wang, Wei-Kun Wang, Ming Yao, Ya-Qin Huang

Journal of Electrochemistry

Sulfurized polyacrylonitrile (SPAN) is regarded as an attractive cathode candidate of lithium-sulfur (Li-S) batteries for its non-dissolution mechanism and effective alleviation of polysulfides shuttling issue in Li-S batteries, displaying high utilization of cathode active material, outstanding cycle stability and structural stability. However, the relation between cyclization degree and cycle stability of SPAN is still unveiled. In this work, SPAN-C-V composites were synthesized by co-introduction of CuSO₄ and zinc n-ethyl-n-phenyldithiocarbamate (ZDB) in the co-heating of sulfur and polyacrylonitrile. The co-introduction of CuSO₄ and ZDB reduced the cyclization reaction onset temperature of PAN while increased the C—C/C=C within SPAN-C-V, thus …

Carbon-Al Interface Effect On The Performance Of Ionic Liquid-Based Supercapacitor At 3 V And 65 OC, Zhen-Zhen Ye, Shu-Ting Zhang, Xin-Qi Chen, Jin Wang, Ying Jin, Chao-Jie Cui, Lei Zhang, Lu-Ming Qian, Gang Zhang, Wei-Zhong Qian

Journal of Electrochemistry

Ionic liquid (IL) electrolyte-based supercapacitors (SCs) have advantages of high operating voltage window, high energy density and nonflammability, as compared to conventional acetonitrile-based organic electrolyte SCs, and are typically suitable for the large-scale energy storage in the era of carbon neutrality full of renewable, but unstable electricity. However, current efforts were concentrated on the study with coin-cell type of IL-SCs, and less has been reported on the pouch type of IL-SCs for a long cycling time yet. To fabricate a reliable SC for the life time test or for the accelerated aging test under high temperature, one should concern the …

Application Of Artificial Intelligence To Lithium-Ion Battery Research And Development, Zhen-Wei Zhu, Jing-Yi Qiu, Li Wang, Gao-Ping Cao, Xiang-Ming He, Jing Wang, Hao Zhang

Journal of Electrochemistry

Lithium-ion batteries (LIBs) have become one of the best solutions to the energy storage issue in modern society. However, the battery materials and device development are both complex, and involve multivariable problems. Traditional trial-and-error approach, which relies on researchers to conduct experiments, has encountered bottlenecks in the improvement of the battery performance. Artificial intelligence (AI) is the most potential technology to deal with this issue due to its powerful high-speed and capabilities of processing massive data. In particular, the capability of machine learning (ML) algorithms in assessing multidimensional data variables and discovering patterns in the sets are expected to assist …

Multi-Electron Reaction-Boosted High Energy Density Batteries: Material And System Innovation, Rui-Qi Guo, Feng Wu, Xin-Ran Wang, Ying Bai, Chuan Wu

Journal of Electrochemistry

The continuous development of the global energy structure transformation has put forward higher demands upon the development of batteries. The improvements of the energy density have become one of the important indicators and hot topic for novel secondary batteries. The energy density of existing lithium-ion battery has encountered a bottleneck due to the limitations of material and systems. Herein, this paper introduces the concept and development of multi-electron reaction materials over the past twenty years. Guided by the multi-electron reaction, light weight electrode and multi-ion effect, current development strategies and future trends of high-energy-density batteries are highlighted from the perspective …

Void-Semiconductor Gaas Photonic Crystal Surface-Emitting Lasers By Epitaxial Regrowth And Single-Epitaxy Methods, Kevin James Reilly

Nanoscience and Microsystems ETDs

Monolithic semiconductor lasers including edge-emitting lasers (EELs) and vertical-cavity surface-emitting lasers (VCSELs) fail to realize simultaneous achievement of both high-power high-quality beams due to intrinsic limitations of their resonant cavity. Photonic crystal surface emitting lasers (PCSELs) address these structural limitations through employment of a two-dimensional photonic crystal (PC) cavity that creates feedback at a single wavelength for laterally scalable devices. This function of the PC allows PCSELs to power scale with area while maintaining single-mode emission required for diffraction-limited beams. In this way, PCSELs fulfill an industry demand for high-power high-quality lasing from a single chip.

Early PCSELs were fabricated …

Enhancing The Performance Of Poly(3-Hexylthiophene) Based Organic Thin-Film Transistors Using An Interface Engineering Method, Eyob Negussie Tarekegn

All Dissertations

An original design and photolithographic fabrication process for poly(3-hexylthiophene-2, 5-diyl) (P3HT) based organic thin-film transistors (OTFTs) is presented. The structure of the transistors was based on the bottom gate bottom contact OTFT. The fabrication process was efficient, cost-effective, and relatively straightforward to implement. Current–voltage (I-V) measurements were performed to characterize the primary electronic properties of the transistors. The measured mobility of these transistors was significantly higher than most results reported in the literature for other similar bottom gate bottom contact P3HT OTFTs. The higher mobility is explained primarily by the effectiveness of the fabrication process in keeping the interfacial layers …

A Fiber-Optic Sensor-Embedded And Machine Learning Assisted Smart Helmet For Multi-Variable Blunt Force Impact Sensing In Real Time, Yiyang Zhuang, Taihao Han, Qingbo Yang, Ryan O'Malley, Aditya Kumar, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

Early on-site diagnosis of mild traumatic brain injury (mTBI) will provide the best guidance for clinical practice. However, existing methods and sensors cannot provide sufficiently detailed physical information related to the blunt force impact. In the present work, a smart helmet with a single embedded fiber Bragg grating (FBG) sensor is developed, which can monitor complex blunt force impact events in real time under both wired and wireless modes. The transient oscillatory signal "fingerprint" can specifically reflect the impact-caused physical deformation of the local helmet structure. By combination with machine learning algorithms, the unknown transient impact can be recognized quickly …

Which Factor Dominates Battery Performance: Metal Ion Solvation Structure-Derived Interfacial Behavior Or Solid Electrolyte Interphase Layer?, Hao-Ran Cheng, Zheng Ma, Ying-Jun Guo, Chun-Sheng Sun, Qian Li, Jun Ming

Journal of Electrochemistry

Solid-electrolyte interphase (SEI) layer formed on the electrode by electrolyte decomposition has been considered to be one of the most important factors affecting the battery performance. We discover that the metal ion solvation structure can also influence the performance, particularly, it can elucidate many phenomena that the SEI cannot. In this review, we summarize the importance of the metal ion solvation structure and the derived metal ion de-solvation behaviors, by which we can build an interfacial model to show the relationship between the interfacial behavior and electrode performance, and then apply to different electrode and battery systems. We emphasize the …

Efficient Interface Enabled By Nano-Hydroxyapatite@Porous Carbon For Lithium-Sulfur Batteries, Jia-Yu Wang, Xue-Feng Tong, Qi-Fan Peng, Yue-Peng Guan, Wei-Kun Wang, An-Bang Wang, Nai-Qiang Liu, Ya-Qin Huang

Journal of Electrochemistry

The dissolution and “shuttle effect” of lithium polysulfides (LiPSs) hinder the application of lithium-sulfur (Li-S) batteries. To solve those problems, inspired by natural materials, a nano-hydroxyapatite@porous carbon derived from chicken cartilage (nano-HA@CCPC) was fabricated by employing a simple pre-carbonization and carbonization method, and applied in Li-S batteries. The nano-HA@CCPC would provide a reactive interface that allows efficient LiPSs reduction. With a strong affinity for LiPSs and an excellent electronic conductive path for converting LiPSs, the shuttle effect of LiPSs was confined and the redox kinetics of LiPSs was substantially enhanced. Li-S batteries employing nano-HA@CCPC-modified separators exhibited long cycle life and …

Advances And Atomistic Insights Of Electrolytes For Lithium-Ion Batteries And Beyond, Tingzheng Hou, Xiang Chen, Lu Jiang, Cheng Tang

Journal of Electrochemistry

Electrolytes and the associated electrode-electrolyte interfaces are crucial for the development and application of high-capacity energy storage systems. Specifically, a variety of electrolyte properties, ranging from mechanical (compressibility, viscosity), thermal (heat conductivity and capacity), to chemical (solubility, activity, reactivity), transport, and electrochemical (interfacial and interphasial), are correlated to the performance of the resultant full energy storage device. In order to facilitate the operation of novel electrode materials, extensive experimental efforts have been devoted to improving these electrolyte properties by tuning the physical design and/or chemical composition. Meanwhile, the recent development of theoretical modeling methods is providing atomistic understandings of the …

Insight Into The Effects Of Cation Disorder And Surface Chemical Residues On The Initial Coulombic Efficiency Of Layered Oxide Cathode, Jin-Li Liu, Han-Feng Wu, Zhi-Bei Liu, Ying-Qiang Wu, Li Wang, Feng-Li Bei, Xiang-Ming He

Journal of Electrochemistry

Lithium layered oxide LiNi_0.6Co_0.2Mn_0.2O₂ (NCM622) is one of the most promising cathode materials in high-energy lithium-ion batteries for electric vehicles. However, one drawback for NCM622 is that its initial coulombic efficiency (ICE) is only about 87%, which is at least 6% lower than that of LiCoO₂ or LiFePO₄. In this work, we investigated the effects of surface chemical residues (e.g., LiOH and Li₂CO₃) and Li/Ni cation disorder resulted during the sintering on the ICE. We found that the ICE of the as-prepared samples could be boosted …

Review On Oxygen-Free Vanadium-Based Cathodes For Aqueous Zinc-Ion Batteries, Xiao-Ru Yun, Yu-Fang Chen, Pei-Tao Xiao, Chun-Man Zheng

Journal of Electrochemistry

Aqueous zinc-ion batteries (AZIBs) are considered as one of the most promising next-generation electrochemical energy storage systems owing to their high-power density, environmental benign, intrinsic safety, and the low cost of the abundant zinc resources. However, their further development is still plagued by the inferior electrochemical performance of cathode materials. Though extensive research has been conducted to investigate various cathode materials (including manganese oxides, vanadium oxides, Prussian blues analogy, and organic materials), design of high-performance cathodes with satisfying capacity and long-term cycling stability still faces great challenges. Oxygen-free vanadium-based compounds, owing to their better conductivity, larger interlayer spacing, lower ion …

Transition-Metal Ions In Β-Ga2O3 Crystals: Identification Of Ni Acceptors, Timothy D. Gustafson, Nancy C. Giles, Brian C. Holloway, J. Jesenovec, B. L. Dutton, M. D. Mccluskey, Larry E. Halliburton

Faculty Publications

Excerpt: Transition-metal ions (Ni, Cu, and Zn) in β-Ga₂O₃ crystals form deep acceptor levels in the lower half of the bandgap. In the present study, we characterize the Ni acceptors in a Czochralski-grown crystal and find that their (0/−) level is approximately 1.40 eV above the maximum of the valence band.

Material Characterization And Comparison Of Sol-Gel Deposited And Rf Magnetron Deposited Lead Zirconate Titanate Thin Films, Katherine Lynne Miles

Mechanical Engineering ETDs

Lead zirconate titanate (PZT) has been a material of interest for sensor, actuator, and transducer applications in microelectromechanical systems (MEMS). This is due to their favorable piezoelectric, pyroelectric and ferroelectric properties. While various methods are available to deposit PZT thin films, radio frequency (RF) magnetron sputtering was selected to provide high quality PZT films with the added capability of batch processing. These sputter deposited PZT films were characterized to determine their internal film stress, Young’s modulus, composition, and structure. After characterization, the sputtered PZT samples were poled using corona poling and direct poling methods. As a means of comparison, commercially …

Development Of An Automated Platform For Sensing And Differentiating Vapor-Phase Btex Constituents, Jonathan Samuelson

USF Tampa Graduate Theses and Dissertations

Light aromatic hydrocarbons are an inevitable byproduct of fossil fuel extraction, refinement, distribution, and use. The four lightest and most prevalent of these are benzene, toluene, ethylbenzene, and xylene, which are known collectively as BTEX. In spite of their chemical similarity these species have markedly different effects on human health and substantially different concentrations are permitted by OSHA in workplaces and by the EPA in ambient air and groundwater. Real-time detection, identification, and quantification of these species is therefore of great importance wherever they see industrial use.This work represents the continuation and advancement of a line of research in which …

Electrochemical Syntheses Of Nanomaterials And Small Molecules For Electrolytic Hydrogen Production, Jia-Qi Wei, Xiao-Dong Chen, Shu-Zhou Li

Journal of Electrochemistry

Hydrogen is a clean, efficient, renewable energy resource and the most promising alternative to fossil fuels for future carbon-neutral energy supply. Therefore, sustainable hydrogen production is highly attractive and urgently demanded, especially via water electrolysis that has clean, abundant precursors and zero emission. However, current water electrolysis is hindered by the sluggish kinetics and low cost/energy efficiency of both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). In this regard, electrochemical synthesis offers prospects to raise the efficiency and benefit of water electrolysis by fabricating advanced electrocatalysts and providing more efficient/value-adding co-electrolysis alternatives. It is an eco-friendly and facile …

Catalytic Effect Of Disordered Ru-O Configurations For Electrochemical Hydrogen Evolution, Xue Sun, Ya-Jie Song, Ren-Long Li, Jia-Jun Wang

Journal of Electrochemistry

Phase engineering is considered as an effective method for modulating the electronic structure and catalytic activity of catalysts. The disordered conformation of amorphous materials allows flexible reforming of the surface electronic structure, showing their attractiveness as catalysts for hydrogen evolution reaction (HER). Herein, we designed and developed an amorphous ruthenium dioxide (a-RuO₂) catalyst with a disordered Ru-O configuration. The conformational relationship between Ru-O ordering and HER performance is established by combining advanced electron microscopic techniques with detailed electrochemical tests. Specifically, the disordered Ru-O coordination significantly enhanced the HER catalytic activity in both acidic and alkaline media, ultimately leading …

Alkaline Water Electrolysis For Efficient Hydrogen Production, Wen-Fu Xie, Ming-Fei Shao

Journal of Electrochemistry

Hydrogen production from water electrolysis is a sustainable and environmentally benign strategy in comparison with fossil fuel-based hydrogen. However, this promising technique suffers from the high energy consumption and unsatisfactory cost due to the sluggish kinetics of both half reaction and inferior stability of electrocatalysts. To address this challenge, herein, we present a timely and comprehensive review on advances in alkaline water electrolysis that is already commercialized for large scale hydrogen production. The design principles and strategies with aiming to promote the performance of hydrogen generation are discussed from the view of electrocatalyst, electrode, reaction and system. The challenges and …

Alkaline Seawater Electrolysis At Industrial Level:Recent Progress And Perspective, Tao Zhang, Yi-Pu Liu, Qi-Tong Ye, Hong-Jin Fan

Journal of Electrochemistry

Industrial hydrogen generation through water splitting, powered by renewable energy such as solar, wind and marine, paves a potential way for energy and environment sustainability. However, state-of-the-art electrolysis using high purity water as hydrogen source at an industrial level would bring about crisis of freshwater resource. Seawater splitting provides a practical path to solve potable water shortage, but still faces great challenges for large-scale industrial operation. Here we summarize recent developments in seawater splitting, covering general mechanisms, design criteria for electrodes, and industrial electrolyzer for direct seawater splitting. Multi-objective optimization methods to address the key challenges of active sites, reaction …

A Self-Supported Ru-Cu3P Catalyst Toward Alkaline Hydrogen Evolution, Zi-Xuan Wan, Chao-Hui Wang, Xiong-Wu Kang

Journal of Electrochemistry

Transition metal phosphide (TMP) is a kind of effective catalysts toward hydrogen evolution reaction (HER) in alkaline electrolytes. However, the performance of TMP catalysts is strongly limited by water splitting. In this work, we developed a method to prepare a copper foam (CF) supported Ru-doped Cu₃P catalyst (Ru-Cu₃P/CF) by a consecutive growth of Cu(OH)₂ nanoarrays, soaking in RuCl₃ solution and phosphorization. A large surface area was obtained by the self-supported catalysts with the appropriative Ru doping. As an excellent HER catalyst, it exhibited a low overpotential of 95.6 mV at a current density of …

Impulse, Fall 2022, University Marketing And Communications, Jerome J. Lohr College Of Engineering

Impulse (Jerome J. Lohr College of Engineering Publication)

2 | Sanjeev Kumar Takes Helm as College’s 12th Dean
5 | College Develops Partnerships in India, Turkey
6 | Faculty News
8 | Aerofly — Profs, Alum Partner To Build Unique Drone
10 | Researchers Find Way to Extend Produce Shelf Life
12 | SDSU Claims National Title in Quarter-Scale Tractors
14 | Nation’s Top ASCE Chapter Housed at SDSU
16 | National Geo-Video Title Won By State Students
18 | Summer Brings Engineering Camps to Campus
20 | Haleigh Timmer — Money on the Court, In Classroom
22 | Daniel Burkhalter — Day in the Life of Student-Athlete …

Preface To Special Issue On Water Electrolysis For Hydrogen Production, Li Li, Jin-Song Hu, Zi-Dong Wei

Journal of Electrochemistry

No abstract provided.

Perovskite-Type Water Oxidation Electrocatalysts, Xiao Liang, Ke-Xin Zhang, Yu-Cheng Shen, Ke Sun, Lei Shi, Hui Chen, Ke-Yan Zheng, Xiao-Xin Zou

Journal of Electrochemistry

The development of energy conversion/storage technologies can achieve the reliable and stable renewable energy supply, and bring us a sustainable future. As the core half-reaction of many energy-related systems, water oxidation is the bottleneck due to its sluggish kinetics of the four-concerted proton-electron transfer (CPET) process. This necessitates the exploitation of low cost, highly active and stable water oxidation electrocatalysts. Perovskite-type oxides possess diverse crystal structures, flexible compositions and unique electronic properties, enabling them ideal material platform for the optimization of catalytic performance. In this review, we provide a comprehensive summary for the crystal structures, electronic structures and synthetic methods …

Recent Development Of Low Iridium Electrocatalysts Toward Efficient Water Oxidation, Jing Ni, Zhao-Ping Shi, Xian Wang, Yi-Bo Wang, Hong-Xiang Wu, Chang-Peng Liu, Jun-Jie Ge, Wei Xing

Journal of Electrochemistry

Developing high-performance and low-cost electrocatalysts for oxygen evolution reaction (OER) is the key to implementing polymer electrolyte membrane water electrolyzer (PEMWE) for hydrogen production. To date, iridium (Ir) is the state-of-the-art OER catalyst, but still suffers from the insufficient activity and scarce earth abundance, which results in high cost both in stack and electricity. Design low-Ir catalysts with enhanced activity and stability that can match the requirements of high current and long-term operation in PEMWE is thus highly desired, which necessitate a deep understanding of acidic OER mechanisms, unique insights of material design strategies, and reliable performance evaluation norm, especially …

The Rapid Preparation Of Efficient Mofeco-Based Bifunctional Electrocatalysts Via Joule Heating For Overall Water Splitting, Ao Zhou, Wei-Jian Guo, Yue-Qing Wang, Jin-Tao Zhang

Journal of Electrochemistry

Water electrolysis is an available way to obtain green hydrogen. The development of highly efficient electrocatalysts is a current research hotspot for water splitting, but it remains challenging. Herein, we demonstrate the synthesis of a robust bifunctional multi-metal electrocatalysts toward water splitting via the rapid Joule-heating conversion of metal precursors. The composition and morphology were well regulated via altering the ratio of metal precursors. In particular, the trimetal MoC/FeO/CoO/carbon cloth (CC) electrode revealed the outstanding bifunctional electrocatalytic performance due to the unique composition and large electrochemical active surface area. Typically, the MoC/FeO/CoO/CC catalyst needed low overpotentials of 121 and 268 …