Materials Science and Engineering Commons^™

Study Of Transport Properties Of Inas Using Monte Carlo Simulation, Satyanadh Gundimada

Electrical & Computer Engineering Theses & Dissertations

The present research is aimed at ascertaining the usefulness of InAs semiconductor material for single photon avalanche photo detectors operating in the Geiger mode at 2 μm wavelengths. InAs is considered as the material suitable for the purpose because of its less bandgap and lower effective mass of the electrons when compared to other semiconductor materials presently in use. Hence, theoretically transient transport properties of bulk InAs are superior and the velocity overshoot phenomena stronger. InAs is a relatively less explored material when compared to other materials like GaAs. The choice of the material is justified with thorough exploration of …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Multipacting is one of the major loss mechanisms in rf superconductivity cavities for accelerators. This loss mechanism limits the maximum amount of energy/power supported by the cavities. Optimal designs have been identified in others’ studies. In practice, these designs are not easily manufactured. Chemical etching processes used to polish the cavity walls result in a nonuniform surface etch. A nonuniform surface etch will leave some unclean areas with contaminants and micron size particles. These significantly affect mutipacting. Further, a nonuniform etch will leave areas with damaged grain structure, which is not good for superconducting properties. Typically, the depth of chemical …

Initial Stages Of Copper Electrodeposition On Glassy Carbon Electrode, Ling Huang, Rui Zhang, Min Gu, Fang-Zu Yang, Shu-Kai Xu, Shao-Min Zhou

Journal of Electrochemistry

Initial stages of copper electrodeposition on glassy carbon electrode from acid sulphate solutions were studied using cyclic voltammetry and chronoamperometry. The electrolyte solution was a 0.05 mol.L^-1 copper sulphate, 1.4～1.8 mol⋅L^-1 sulphuric acid containing 1 mg·L^-1 2-mercaptobenzoimidazole, Results show that 2-mercaptobenzoimidazole produced an inhibition of the copper deposition, probably related to the adsorption,sulphuric acid promote copper electrodeposition. The initial deposition kinetics corresponded to a model including instantaneous nucleation and diffusion controlled growth.Addition of 2-mercaptobenzoimidazole and sulphuric acid did not change the initial nucleation of copper electrocrystallization, it increased the nucleation rate and the number density of nuclei …

Ionic Conduction In Ba0.95Ce0.9Y0.1O3 - Α Solid Oxide And Its Performance In Fuel Cell, Gui-Lin Ma, Ding-Xian Jia, Li-Gan Qiu, Hui Shi, Rong Chen

Journal of Electrochemistry

Using Ba_0.95Ce_0.9Y_0.1O_3-α as a solid electrolyte and porous platinum as electrodes,hydrogen and oxygen concentration cells and hydrogen-air fuel cell were constructed, respectively. Electromotive forces (MEFs) of the gas concentration cells and I-V characteristics of the fuel cell were detdrmined in the temperature range of 600～1 000 ℃. The Ba_0.95Ce_0.9Y_0.1O_3-α exhibited almost the pure protonic conduction under hydrogen gas,and a mixed conduction of oxide-ion and electron hole with oxide-ion transport number of 0.3～0.5 under oxygen gas. It exhibited a mixed conduction of proton and oxide-ion with the …

Some Consideration For Lithium-Ion Cells' Safety, Guang-Xia Hu, Jing-Ying Xie

Journal of Electrochemistry

The safety is the most important problem for lithium ion cells, especially for large lithium ion cells. In this paper, some information about lithium ion cells' safety can be learned by discussing several aspects of lithium ion cells, such as, materials of lithium ion cell, manufacturing processes, using conditions and so on.

Synthesis And Characterization Of Lini0.8-XAlXCo0.2O2 As Cathodes For Lithium-Ion Batteries, Jun Zhang, Zhong-Kao Jin, Qing-He Yang, Qing-Mei Song, Xiao-Hua Ma, Xiang-Fu Zong

Journal of Electrochemistry

Single-phase solid solution of LiNi_0.8-xAl_xCo_0.2O₂ (0≤ x <0.1)had been synthesized and characterized by X-ray diffraction(XRD) and scanning electron microscopy (SEM). Their electrochemical performance was examined by charge-discharge cycling. The LiNi_0.71Al_0.09Co_0.2O₂ compound showed a discharge capacity of 152 mAh/g after 20 cycles that corresponds to 97.4% capacity retention. The beneficial effect of co-doping with Al and Co elements was corro-borated by slow scanning cyclic voltammograms(SSCV), electrochemical impedance spectrum (EIS) and differential scanning calorimetry (DSC) data on charged cathodes. These results show that the 2D-character of the crystal lattice was stabilized by co-doping with Al and Co, the phase transitions that occur during deintercalation or intercalation of Li-ions were significantly suppressed, …

Research Progress On Electrode Material In All-Vanadium Redox Battery, Hua Li, Shou-Wen Chang, Chuan-Wei Yan

Journal of Electrochemistry

An all-vanadium redox flow storage battery possesses many advantages over conventional storage batteries.The development statue of two types electrode materials (metal and compound type) is introduced in this article.

Optimum Of Catalyst Layers For Direct Methanol Fuel Cells, Jun Zhang, Lei Li, Li Xu, Yu-Xin Wang

Journal of Electrochemistry

The performances of membrane electrode assemblies (MEAs)with various Pt loading were compared. The amount of Nafion in a catalytic layer was optimized, and the effect of Nafion loading on the resistance of MEAs was investigated with ac impedance spectroscopy. For a MEA with both Pt 4 mg/cm² in the anode and the cathode, suitable Nafion loading was 21.4 wt% in the anode. With 21.4 wt% Nafion loading in the cathode, the Direct Methanol Fuel Cells(DMFC) showed the highest performance at high current density. While, the DMFC performances came down, as Nafion loading increasing,for ohm and concentration polarization.

Modification Of Molybdenum Nitride Electrode For Supercapacitor(I)——The Effect Of Ammonium Vanadate On The Properties Of Molybdenum Nitride Electrode, Xue-Liang Li, Dao-Rong Luo, Hua-Lin Wang, Jian-Bo He, Yun-Guei Zhu

Journal of Electrochemistry

The effect of vanadium on the properties of the electrode of molybdenum nitride has been studied by using XRD, SEM and cyclic voltammetry. Modified molybdenum nitride was made as follow: films were coated by dipping titanium sheet in the solution containing different composition of molybdenum oxide, ammonium vanadate, ammonia, glycol and oxalic acid, and coated films are reacted with free ammonia. The results show that the specific capacitance of modified electrode was considerably increased and the operation voltage was broadened with the addition of ammonium vanadate in the dipping solution. The mechanism of these effects generated is the formation of …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: I. Swamp Water, Sulistyoweni Widanarko, Henki W. Ashadi, Andri Krisnadi Wicaksono

Makara Journal of Technology

Most of infrastructures using steel concrete to reinforce the strength of concrete. Steel concrete is so vulnerable to chemical compounds that can cause corrosion. It can happen due to the presence of chemical compounds in acid environment in low pH level. These chemical compounds are SO4 2-, Cl-, NO3 -. There are many swamp area in Indonesia. The acid contents and the concentration of ion sulphate, chlorides, and nitrate are higher in the swamp water than in the ground water .The objective of this research was to find out the influence of corrosive chemicals in the swamp water to the …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: Ii. Swamp Sludges, Henki W. Ashadi, Sulistyoweni Widanarko, Irma Gusniani

Makara Journal of Technology

A polluted environment will influence the building age. The objective of this research was to find out the influence of corrosive chemicals within the sludge swamp area with the corrosion rate of steel concrete. Corrosion in steel concrete usually occur in acid area which contain of SO4 2-, Cl- and NO3 -. The research treatment used by emerging ST 37 and ST 60 within 60 days in ‘polluted’ sludge swamp area. Three variation of ‘polluted’ swamp sludge were made by increasing the concentration a corrosive unsure up to 1X, 5X and 10X. The corrosion rate measured by using an Immersion …

The Effect Of Ca Content On Cao-Zeolite On Nitrogen Adsorption Capacity, Mohammad Nasikin, Tania Surya Utami, Agustina Tp Siahaan

Makara Journal of Technology

In industry, Ca zeolite is used as nitrogen selective adsorbent with the use of PSA (Pressure Swing Adsorption)/VSA (Vacuum Swing Adsorption) methods. Natural zeolite modified to be Cao-zeolite by ion exchange process using Ca(OH)2. Adsorption test was done on CaO-zeolite with different Ca concentration to understand how it’s adsorption phenomena on oxygen and nitrogen. Adsorption test has been done for CaO-zeolite with Ca concentration = 0,682%, 0,849% and 1,244% to oxygen and nitrogen with equal concentration seperately. Pressure variation has being done three times (5 minutes long each time) adsorption time to analyze the connection between adsorption time and how …

Cetane Number Booster Additive For Diesel Fuel Synthesized From Coconut Oil, Mohammad Nasikin, Rita Arbianti, Abdul Azis

Makara Journal of Technology

To reduce NOx, SOx, HC, and particulates that produce because of using diesel fuel, can be done by increasing cetane number. One of methods is adding an additive to diesel fuel. 2-Ethyl Hexyl Nitrate (2-EHN) is a commercial additive that an organic nitrate. Making an additive in this research is used palm oil by nitration reaction that used HNO3 and H2SO4. Result of this reaction is methyl ester nitrate that has a structure looks like 2-EHN. IR spectra from research show that methyl ester nitrate is indicated by spectrum NO2 at 1635 cm-1. This result show that methyl ester nitrate …

Analogy Method Development For Cost Estimation Of Software Design, Riyanarto Sarno, Joko Lianto Buliali, Siti Maimunah

Makara Journal of Technology

The important aspect of planning and managing software development project is to estimate the cost of a project. There are several methods for estimating the cost of a software development project, and the Analogy method is a method which gives relatively better estimates. This paper shows that the modified Analogy method selects a closer project reference, estimates more accurate project effort and cost. This study enhances the cost estimate technique by including valid and complete cost parameters, therefore the estimate of a project cost is better than the result of the standard Analogy method.

The Role Of Si3n4 Amorphous Phase In Nc-Tin/A-Si3n4 Nanocomposites In Increases The Hardness And Thermal Stability, Keba Moto

Makara Journal of Technology

The role of Si3N4 amorphous phase in nc-TiN/a-Si3N4 nanocomposites will be shown and compared with polycrystalline ZrN/Ni which has no such amorphous phase (non-composites). The presence of amorphous phase Si3N4 increases the hardness of film as well as the toughness of the bulk nanocomposites under indentation load. It has been observed that nc-TiN/a-Si3N4 nanocomposites films has higher thermal stability than ZrN/Ni polycrystalline films.

Biodiesel's Characteristics Preparation From Palm Oil, Tilani Hamid. S, Rachman Yusuf

Makara Journal of Technology

Biodiesel’s characteristics preparation from palm oil. Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester) by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH) as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio …

Development Of Hardness Measurement Procedure For Nanocomposite Nc-Tin/A-Si3n4, Keba Moto

Makara Journal of Technology

Hardness of nc-TiN/a-Si3N4 nanocomposites which was determined by using two methods of measurements i. e. depth sensing method and remaining plastic indentation area that were magnified by using SEM (Scanning Electron Microscope) lie in the good agreement. The hardness value is not influenced by the biaxial and residual compressive stress. The measurement of the biaxial stress on the substrate shows a very small value of biaxial stress as well as the constant hardness and crystallite size against annealing temperature. Therefore, the reported hardness value here is the intrinsic value that depend on its microstructure properties.

Study Of Non-Equilibrium Electron Dynamics In Metals, Wael Mohamed Gomaa Ibrahim

Electrical & Computer Engineering Theses & Dissertations

Thermal phenomena, such as heat propagation, lattice melting, and ablation, are the result of energy deposition in metals. A fundamental understanding of the electron dynamics leading to these thermal phenomena would benefit many laser applications, such as laser deposition of thin films and laser processing.

In this work, thin metal films were prepared using the resistive heating evaporation technique. High dynamic range autocorrelators were constructed to characterize the different laser systems used in this study. The nonequilibrium electron dynamics in single layer gold films, multi-layer gold-vanadium, and gold-titanium films were studied. The time evolution of the electron temperature was monitored …

An Investigation On Sr-Doped Spinel Phase-LisrXMn2-XO4, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

Sr-doped spinel phase-LiSr_xMn_2-xO₄ was successfully prepared by solid-state method. Structural and electrochemical characterizations were carried out. Although Sr²⁺ has a large ion radius-1.12 , the spinel structure can be well maintained for LiSr_xMn_2-xO₄ sample as far as the x value doesn't surpass 0.05. Electrochemical study presents supporting evidence that doping the stoichiometric LiSr_xMn_2-xO₄ phase with Sr is an effective way to improve the cycleability of LiSr_xMn_2-xO₄ spinel material. A remarkable enhancement of the cycleability with retention of the initial …

Electrosynthesis Of Glyoxylic Acid In A Cooled Cathode Reactor, Jin-Hong Fan, Jun Li, Xue-Yun Chen, Wei Li, Hao-Qi Gao

Journal of Electrochemistry

Glyoxylic acid was produced by electroreduction of oxalic acid in a well designed cooled cathode reactor. The cathodic and anodic electrolytes were super-saturated oxalic acid and hydrochloric acid aqueous solutions separated by a super-acid ion-exchange membrane. The current efficiency and time-space yield of glyoxylic acid were studied under different temperatures of cathode and electrolyte, current densities, materials of cathode. With the cooled cathode reactor, the energy consumption was reduced and higher oxalic acid concentration was available in solution, so that current efficiency was improved. The results indicated that the average time-space yield of glyoxylic acid was about 0.032 kg·dm^{-3 …}

Development Of 200～500 W Portable Proton Exchange Membrane Fuel Cell Power System, Li-Qing Hu, Li-Rong Zhou, Zheng Li, Jian-Wei Xia, Ming-Zhu Fu, Xin Wu, Yun Zhu

Journal of Electrochemistry

The Properties of the Portable PEM Fuel Cell Power Source are very unique compared with the common primary or rechargeable electro-chemical battery. This paper describes the In this work, of the 200～500 W portable PEM fuel cell power system, was developed. The system mainly composed of four subsystem: 1)Fuel cell stack; 2)Air delivery; 3)Hydrogen source; 4)Heat dissipation and system control.

Corrosive Electrochemical Behavior Of Carbon Steel In Microbiological Medium, Jing Liu, Hong-Bo Fan, Hai-Ping Xu, Jia-Shen Zheng, Li-Ming Xu, Zong-Qiang Mao

Journal of Electrochemistry

Sulfate-reducing bacteria (SRB)grows and propagates, PH of the solution is dropped from 7.5 to 5.8, and forms the biofilms on carbon steel in culture medium. The micro-environment on the surface of carbon steel is changed under the biofilms, the factors accelerate the formation of the pitting corrosion. When the biofilm on carbon steel is cleaned out, the surface of carbon steel have the non-uniform pitting corrosion. The activity of SRB and the porous structure of biofilms induced the initiation and development of the pitting corrosion of carbon steel. The process of microbiologically induced corrosion (MIC) involves the development of SRB …

Electrocatalytic Oxidation Of Formaldehyde On The Proline Film Modified Electrode, Yu-Rong Ma, Qiu-Xia Yang, Guo-Bao Li, Zheng-Kai Xi, Xue-Lin Wang

Journal of Electrochemistry

The proline film modified electrode and its electrochemical behavior was studied by cyclic voltammetry and spectroelectrochemistry. After incorporation of Ni(Ⅱ), the cyclic voltammograms of the proline Ni(Ⅱ) film electrode exhibited a typical redox peak, which appeared at potential of 0.52 V anodic and 0.44 V cathodic in NaOH. The formal potentials E' were linearly dependent on the pH, and the peak currents ip were linearly dependent on the square root of the scan rates, thus charge transfer in the film was controlled by diffusion. The diffusion coefficient is figured out to be 2×10^_-10 cm²·s^-1. The …

Preparation,Structure And Properties Of Electrochromic Rhodium Oxide Films, Hai-Hong Wang, Tao Wang, Man-Ming Yan, Zhi-Yu Jiang

Journal of Electrochemistry

Electrochromic rhodium oxide films were prepared on ITO substrate by sol-gel method. The films exhibited reversible two-color (bright yellow at reduction and dark green at oxidation) electrochromic behavior in alkaline solution with good cycle stability. In-situ XRD, TGA-DTA, IR, XPS methods were used for studying the structure and chemical process of the films. The diffusion coefficient during the electrochromic process was measured by electrochemical impedance spectra method. It was found that the rhodium oxide films may be suitable for the use in electrochromic devices.

Recent Developments In The Electrolyte For Lic6/Electrolyte/Cathode Battery, Cui-Ying Wang, Sheng-Liang Zhao, Guang-Ming Zhu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

We present a reviewed the development and status of electrolyte for LiC 6/electrolyte/cathode battery. The effect of the salt, solvent, additive and impurity on the conductivity of the electrolyte, formation of the solid-electrolyte-interphase (SEI) and cycle life of the battery were described.

Syntheses And Photoluminescence Of Zinc Oxide Polyaniline Coaxial Nanowires And Their Array, Zhi-Xin Zheng, Yan-Yan Xi, Ping Dong, Huai-Guo Huang, Jian-Zhang Zhou, Lin-Lin Wu, Zhong-Hua Lin

Journal of Electrochemistry

A novel nanomaterial, zinc oxide (ZnO) and polyaniline (PANI) coaxial nanowires and their array in the template, was synthesized using anodic aluminum oxide (AAO) membrane as template. The morphology of these coaxial nanowires was observed with transmission electron microscope (TEM). The experiments on photoluminescence (PL) of coaxial nanowires and their array in AAO membrane show that the visible emission band of ZnO shifts from 530 nm to 400 nm and the luminescence is enhanced for the coaxial nanowires array in AAO membrane,and the visible emission band shifts to a lower wavelergth (385 nm) for coatial nanowires in NaOH solution. Possible …

Electrochemical Properties Of Mixed Metal Oxide Coated Titanium Anodes In Seawater, Ting-Yong Wang, Li-Kun Xu, Guang-Zhang Chen

Journal of Electrochemistry

Mixed metal oxide coated titanium anodes prepared by thermal decomposition were characterized by scanning electron microscopy and electrochemical measurement, while the consumption rate of an anode was also measured in seawater. In order to examine the practical performances of mixed metal oxide-coated anodes, a simulating test on floating dock in seawater has also been carried out. The SEM results indicate that oxide layers exhibited a cracked-mud morphology which endows the anode with good electrocatalytic activity. The electrochemical measurements showed that mixed metal oxide-coated anodes exhibit excellent electrochemical activity and electrochemical stability in seawater. Owing to good corrosion resistance and low …

A Blend Conducting Membranes For Direct Methanol Fuel Cells, Lei Li, Jun Zhang, Hong Wu, Yu-Xin Wang

Journal of Electrochemistry

An attempt was made to modify membranes for direct methanol fuel cells by blending Nafion or polystyrene sulfonic acid (PSSA) with polyvinylidene fluoride (PVDF) from their solutions. The proton conductivity and methanol barrier property as a function of the membrane compositions are discussed. Compared with the Nafion 117 membrane, the PVDF-Nafion blend membranes with 25 wt% of Nafion showed a decrease in the conductivity by about 2 orders of magnitude, and the methanol barrier properties increased about 3 orders of magnitude. If the ratio (σ/P) is adopted to characterize the performance of the membrane, the PVDF-PSSA and PVDF-Nafiion blend membranes …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces led to the use of a buffered chemical polishing procedure for surface cleaning to get good performance of the cavities. This proposal discusses the second phase of research in the second year of the project.

The first phase (starting Summer 2001) has resulted in improving the basic understanding of multipacting and the process of chemical etching. Based …

Integrating Passenger And Modulo As Learning Tools For Collaborative Engineering Education, Kalamullah Ramli, Frank Schwarz, Stefan Werner, A Halim Shamsuddin, Axel Hunger

Makara Journal of Technology

The University of Indonesia (UI), Gerhard Mercator University (GMU), the Universiti Kebangsaan Malaysia (UKM) have agreed to cooperate as partners to develop a joint bachelor (3+1) and masters (1+1) degree, and collaborate in the research fi elds of multimedia- and internet-based learning and application level active networks. This paper describes the introduction of the Offshore Project and the extending of information technology applications to the partner institutions in this international cooperation which would very much enhance the operations of the new initiative in engineering education, which could provide students in far distance with more fl exible learning environment.