Materials Science and Engineering Commons^™

Stability Of A Solid Oxide Cell Stack Under Direct Internal-Reforming Of Hydrogen-Blended Methane, Ya-Fei Tang, An-Qi Wu, Bei-Bei Han, Hua Liu, Shan-Jun Bao, Wang-Lin Lin, Ming Chen, Wan-Bing Guan, Subhash C. Singhal

Journal of Electrochemistry

In this work, the long-term stability and degradation mechanism of a direct internal-reforming solid oxide fuel cell stack (IR-SOFC stack) using hydrogen-blended methane steam reforming were investigated. An overall degradation rate of 2.3%·kh^–1 was found after the stack was operated for 3000 hours, indicating a good long-term stability. However, the voltages of the two cells in the stack were increased at the rates of 3.38 mV·kh^–1 and 3.78 mV·kh^–1, while the area specific resistances of the three metal interconnects in the stack were increased to 0.276 Ω·cm², 0.254 Ω·cm² and 0.249 Ω·cm^{2 …}

Enhancing Electromigration Reliability In Solder Interconnects Through Microstructure Control And Thermomechanical Failure Mechanisms In Thin Metal Lines Under Surge Current Conditions, Hariram Mohanram

Material Science and Engineering Dissertations - Archive

The relentless miniaturization of semiconductor devices has intensified reliability challenges in electronic packaging, particularly for solder interconnects and thin metal lines. This dissertation investigates two critical failure mechanisms—electromigration (EM) and thermomechanical fatigue (TMF)—and explores strategies to mitigate these effects. Electromigration, driven by high-density current-induced atomic migration, significantly impacts solder interconnects. This study examines the role of Under-Bump Metallization (UBM) and solder microstructure in improving EM reliability. Findings reveal that thicker UBMs delay void nucleation and enhance EM resistance, while the absence of UBM leads to failure through vertical void propagation. Additionally, grain orientation, particularly the c-axis alignment in Sn grains, …

Nano-Patterned Si Structures For Optical Filters And Electro-Mechanical Relays: Fabrication, Characterization, Prospects, And Limitations, Md Ataul Mamun

Theses and Dissertations

Nanofabrication technology, especially nanopatterning, is a rapidly advancing field that has already resulted in creating novel devices and holds promise for producing even more with unmatched performance. These techniques also allow us to gain insight into physical phenomena at the micro- and nanoscale. The ultimate performance of nanofabricated devices and their compatibility with existing Si-based CMOS technology hinge upon the careful selection of materials and precise design, coordinated with meticulous pattern transfer. In this work, we applied nanopatterning techniques on silicon to create optical filters for the shortwave infrared (SWIR) region and nanoelectromechanical system (NEMS) relay-based logic gates. Additionally, these …

Fabrication Of Smooth Sac305 Thin Film Via Magnetron Sputtering, M. Ojha, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

SAC305 (96.5 wt% Sn, 3 wt% Ag, 0.5 wt%Cu) solder is increasingly becoming popular due to its reliability good characteristics and performance in addition to the environmental concerns and regulations that restrict the use of lead in nano/microelectronic products. In nano/microelectronics, manufacturing smooth solder coatings free of defects such as voids and cracks, which can compromise joint reliability is crucial. Magnetron sputtering offers a high degree of control over film thickness and composition, resulting in films with excellent uniformity and adhesion. Despite these advantages, fabricating continuous and robust SAC305 films using magnetron sputtering remains a difficult task with limited research …

A Comprehensive Review Of Piezoelectric Ultrasonic Motors: Classifications, Characterization, Fabrication, Applications, And Future Challenges, Sidra Naz, Tian-Bing Xu

Mechanical & Aerospace Engineering Faculty Publications

Piezoelectric ultrasonic motors (USMs) are actuators that use ultrasonic frequency piezoelectric vibration-generated waves to transform electrical energy into rotary or translating motion. USMs receive more attention because they offer distinct qualities over traditional magnet-coil-based motors, such as miniaturization, great accuracy, speed, non-magnetic nature, silent operation, straightforward construction, broad temperature operations, and adaptability. This review study focuses on the principle of USMs and their classifications, characterization, fabrication methods, applications, and future challenges. Firstly, the classifications of USMs, especially, standing-wave, traveling-wave, hybrid-mode, and multi-degree-of-freedom USMs, are summarized, and their respective functioning principles are explained. Secondly, finite element modeling analysis for design and …

Ultra-Fast Annealing Improves Snr And Long-Term Stability Of A Highly Multiplexed Line-By-Line Fbg Array Inscribed By Femtosecond Laser In A Coreless Fiber For Extreme-Temperature Applications, Farhan Mumtaz, Bohong Zhang, Jeffrey D. Smith, Ronald J. O'Malley, Rex E. Gerald, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This study reports the fabrication of an 4th-order line-by-line Fiber Bragg Gratings (FBG) array using femtosecond laser inscription within a highly multimode coreless optical fiber, with a particular focus on achieving substantial multiplexing capabilities. An ultra-fast annealing procedure is employed, resulting in an impressive enhancement of the FBG sensor's fringe visibility by approximately 13 dB, signifying a notable improvement of approximately ~4 dB. This substantial enhancement contributes to the long-term stability and performance of the multiplexed FBG array in extreme temperature conditions. The systematic fabrication approach employed for the multiplexed FBG array guarantees a high signal-to-noise ratio (SNR) for each …

Underlying Substrate Effect On Electrochemical Activity For Hydrogen Evolution Reaction With Low-Platinum-Loaded Catalysts, Baleeswaraiah Muchharla, Peter V. Sushko, Kishor K. Sadasivuni, Wei Cao, Akash Tomar, Hani Elsayed-Ali, Adetayo Adedeji, Abdennaceur Karoui, Joshua M. Spurgeon, Bijandra Kumar

Electrical & Computer Engineering Faculty Publications

Platinum is known as the best catalyst for the hydrogen evolution reaction (HER) but the scarcity and high cost of Pt limit its widespread applicability. Herein, the role of the underlying substrate on the HER activity of dispersed Pt atoms is uncovered. A direct current magnetron sputtering technique is utilized to deposit transition metal (TM) thin films of W, Ti, and Ta as underlying substrates for extremely low loading of Pt (

Direct Measurement Of Microwave Loss In Nb Films For Superconducting Qubits, B. Abdisatarov, D. Bafia, A. Murthy, G. Eremeev, H. E. Elsayed-Ali, J. Lee, A. Netepenko, C. P. A. Carlos, S. Leith, G. J. Rosaz, A. Romanenko, A. Grassellino

Electrical & Computer Engineering Faculty Publications

Niobium films are a key component in modern two-dimensional superconducting qubits, yet their contribution to the total qubit decay rate is not fully understood. The presence of different layers of materials and interfaces makes it difficult to identify the dominant loss channels in present two-dimensional qubit designs. In this paper, we present the study that directly correlates measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radio frequency (SRF) resonator. By using a 3D SRF structure, we are able to isolate the niobium film loss …

Effect Of Annealing On Photoluminescence From Defects In Gan, Oleksandr Andrieiev

Theses and Dissertations

Annealing is a critical process in modern GaN technology, essential for achieving p-type conductivity by activating the Mg_Ga acceptor, as first demonstrated by Shuji Nakamura in the early 1990s. Despite the omnipresence of hydrogen as an impurity in GaN crystals, the precise mechanisms governing hydrogen diffusion and acceptor passivation remain only partially understood. The presented research investigates the effects of annealing-induced activation and hydrogen passivation on C and Be acceptors in GaN grown by MOCVD, HVPE, and MBE methods. We explored these effects by using several annealing techniques, gas compositions, and thermal regimes. A transient behavior between the C …

Electrospun Pt-Tio₂ Nanofibers Doped With Hpa For Catalytic Hydrodeoxygenation, Amos Taiswa, Randy L. Maglinao, Jessica M. Andriolo, Sandeep Kumar, Jack L. Skinner

Civil & Environmental Engineering Faculty Publications

Electrospinning is utilized to fabricate catalytic nanofiber scaffold for biocrude upgrading in hydrodeoxygenation (HDO) following computational studies suggesting the need for nano-catalysts for efficient HDO conversion and selectivity. Here, Pt-TiO₂ nanofibers are fabricated through electrospinning, followed by wet impregnation with a heteropoly acid (HPA), tungstosilicic acid. Intensive heat treatments were incorporated during and after processes to obtain a HPA doped Pt-TiO₂ nano-catalyst. Catalytic HDO was performed in a batch reactor with phenol as the raw biocrude dissolved in hexadecane. The HPA doped Pt-TiO₂ catalyst demonstrated promising HDO performance of 37.2% conversion and a 78.9% selectivity to oxygen …

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Schaeffler Icvd Coating Machine, Louis Mcgrath

Williams Honors College, Honors Research Projects

Chemical Vapor Deposition (CVD) is mutual technology used to deposit thin film through a gaseous phase by vaporizing the solid materials. This conventional process usually requires high thermal stability of the materials, which is not applicable for most of the polymeric materials. Therefore, a novel process, initiated Chemical Vapor Deposition (iCVD) is developed by introducing the gaseous monument and initiator to form the thin film in-situ. By adjusting the free-radical polymerization in the vapor phase, a variety of thin and uniform polymer films can be achieved. Depending on the chemistry, iCVD has many categories. This report explains the design …

Extending Trailer, Alex Grove

Williams Honors College, Honors Research Projects

The goal of this research project is to revolutionize the convenience in towable transportation. This innovative design aims to enhance the versatility of pull-behind trailers by incorporating an extendable feature, allowing users to effortlessly adjust the length according to their specific needs. Whether navigating tight spaces or accommodating extra cargo, our trailer adapts to diverse situations, providing unmatched flexibility. In addition to its adjustable length, the trailer is engineered to be compactable, addressing the storage constraints often faced by users with limited space. The collapsible design ensures easy storage without compromising on functionality, making it an ideal solution for individuals …

Photoluminescence Of Beryllium-Related Defects In Gallium Nitride, Mykhailo Vorobiov, Mykhailo Vorobiov

Theses and Dissertations

This study explores the potential of beryllium (Be) as an alternative dopant to magnesium (Mg) for achieving higher hole concentrations in gallium nitride (GaN). Despite Mg prominence as an acceptor in optoelectronic and high-power devices, its deep acceptor level at 0.22 eV above the valence band limits its effectiveness. By examining Be, this research aims to pave the way to overcoming these limitations and extend the findings to aluminum nitride and aluminum gallium nitride (AlGaN) alloy. Key contributions of this work include. i)Identification of three Be-related luminescence bands in GaN through photoluminescence spectroscopy, improving the understanding needed for further material …

Machine-Learning-Assisted Design Of Deep Eutectic Solvents Based On Uncovered Hydrogen Bond Patterns, Usman Lame Abbas, Yuxuan Zhang, Joseph Tapia, Md Selim, Jin Chen, Jian Shi, Qing Shao

Markey Cancer Center Faculty Publications

Non-ionic deep eutectic solvents (DESs) are non-ionic designer solvents with various applications in catalysis, extraction, carbon capture, and pharmaceuticals. However, discovering new DES candidates is challenging due to a lack of efficient tools that accurately predict DES formation. The search for DES relies heavily on intuition or trial-and-error processes, leading to low success rates or missed opportuni- ties. Recognizing that hydrogen bonds (HBs) play a central role in DES formation, we aim to identify HB features that distinguish DES from non-DES systems and use them to develop machine learning (ML) models to discover new DES systems. We first analyze the …

Passive Wireless Corrosion And Temperature Detection In High-Temperature Environments, Noah Lane Strader

Graduate Theses, Dissertations, and Problem Reports (ETD)

This work focuses on the theory and development of LC sensors for high temperature and corrosion measurement for stainless steel and copper surfaces with power industry and general corrosion detection applications. The LC resonators were fabricated via screen printing an Ag inductor on an alumina substrate. The LC design was modeled using the ANSYS HFSS modeling package. The LC passive wireless sensors operate with resonant frequencies centered at 85-110 MHz. The wireless response of the LC sensor was interrogated and received by a radio frequency signal generator and spectrum analyzer at temperatures from 50-800 °C for copper ground planes and …

Natural Convection Heat Transfer Characteristics Of Sierpinski Carpet Fractal Fins In Horizontal And Vertical Orientations, Ayomide Ayoola

College of Graduate Studies: Theses & Dissertations

This study investigates the thermal performance of fins with perforations inspired by the Sierpinski carpet fractal pattern under natural convection conditions in both vertical and horizontal orientations. The objective is to analyze the effects of fractal iteration levels on three primary performance metrics: efficiency, effectiveness, and effectiveness per unit mass. Experimental evaluations were conducted for fractal fins from iterations 0 through 4, utilizing aluminum material, with each fin heated to controlled conditions. The results reveal that efficiency generally decreases with higher fractal iterations, reflecting increased thermal resistance associated with greater porosity and complex geometry. However, effectiveness per unit mass improves …

Femtosecond Laser–Inscribed Fiber Bragg Grating Sensors: Enabling Distributed High- Temperature Measurements And Strain Monitoring In Steelmaking And Foundry Applications, Ogbole Collins Inalegwu, Yeshwanth Reddy Mekala, Rony Kumer Saha, Farhan Mumtaz, Dinesh Reddy Alla, Deva Prasaad Neelakandan, Jeffrey D. Smith, Ronald J. O'Malley, Rex Gerald, Jie Huang

PSMRC Faculty Research

This study demonstrates the use of fiber Bragg grating (FBG) sensors for distributed temperature and strain monitoring in steelmaking and foundry applications. Integrated into inexpensive optical fibers, FBGs offer accurate and real-time remote sensing, detecting shifts in wavelength due to temperature (up to 1,800 °C), strain, or structural wear and tear. Furthermore, the intrinsic features of FBG sensors: compact size, immunity to electromagnetic interference and corrosion, robustness to vibration, ease of integration into existing composite structures, and non-intrusive measurement capacity in harsh environments make them ideal for steelmaking. FBGs optimize production, ensure quality, and enhance safety within the steel industry.

Enhanced Bottom Anode Monitoring In Dc Electric Arc Furnaces Using Fiber Optic Sensors, Yeshwanth Reddy Mekala, Rony Kumer Saha, Ogbole Collins Inalegwu, Muhammad Roman, Farhan Mumtaz, Rex Gerald, Jeffrey D. Smith, Jie Huang, Ronald J. O'Malley

PSMRC Faculty Research

A pin style bottom anode employs conductive steel rods that serve as the pathway for the high electrical power through rammed refractory at the bottom of a DC Electric Arc Furnace (EAF). Anode wear during operation is important to monitor, as anode replacement is expensive and impacts EAF productivity. Liquid steel penetration into the un-sintered refractory layer can result from rapid electrical power ramp-up, dips in furnace temperature, or operating the anode for too long between EAF campaigns. In extreme cases, the liquid steel may penetrate the bottom of the furnace when anode wear progresses too close to the bottom …

Fiber-Optic Raman Probe For On-Line Eaf Slag Analysis, Bohong Zhang, Hanok Tekle, Jeffrey D. Smith, Todd Sander, Ronald J. O'Malley, Jie Huang

PSMRC Faculty Research

In Electric Arc Furnace (EAF) steelmaking, the push for improved efficiency requires accurate analysis of the chemical composition of its slag system to control slag foaming, provide refractory protection, and maintain high furnace iron yield. Therefore, the ability to obtain real-time slag chemistry data would provide a useful tool to improve the control and efficiency of the process. The work reported here aims to assess the structure and chemistry of EAF slags at high temperatures using a portable fiber-optic Raman probe. The ability to relate Raman spectra peaks to chemistry and structure is demonstrated in experimental result with EAF slags …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Application Of Quantum Algorithms In The Synthesis Of Dynamic Objects, Noilakhon Yakubova

Chemical Technology, Control and Management

Around the world, the food industry is focusing on achieving energy and resource efficiency. One of the main challenges in the field of process automation is the creation of effective control systems using intelligent technologies to improve the quality of processes and achieve the production of high-quality products with less energy and resources. Therefore, it is necessary to work with a large amount of data. Particular attention is paid to the development of computational algorithms for automated high-speed computational analysis systems for processing this data at high speed. Therefore, the article discusses the use of quantum computing methods in controlling …

Electrochemical Performance Of Porous Ceramic Supported Tubular Solid Oxide Electrolysis Cell, Heng-Ji Wang, Wen-Guo Chen, Zhou-Yi Quan, Kai Zhao, Yi-Fei Sun, Min Chen, Ogenko Volodymyr

Journal of Electrochemistry

Solid oxide electrolysis cell (SOEC) is an efficient and clean energy conversion technology that can utilize electricity obtained from renewable resources, such as solar, wind, and geothermal energy to electrolyze water and produce hydrogen. The conversion of abundant intermittent energy to hydrogen energy would facilitate the efficient utilization of energy resources. SOEC is an all-ceramic electrochemical cell that operates in the intermediate to high temperature range of 500–750 ℃. Compared with traditional low temperature electrolysis technology (e.g., alkaline or proton exchange membrane cells operating at ~100 ℃), the high-temperature SOEC can increase the electrolysis efficiency from 80% to ~100%, providing …

Nitrogen-Doped Graphite Felt On The Performance Of Aqueous Quinone-Based Redox Flow Batteries, Heng Zhang, Li-Xing Xia, Shan Jiang, Fu-Zhi Wang, Zhan-Ao Tan

Journal of Electrochemistry

Modification of electrode is vitally important for achieving high energy efficiency in aqueous quinone-based redox flow batteries (AQRFBs). The modification of graphite felt (GF) was carried out by means of urea hydrothermal reaction, and simultaneously, the effects of hydrothermal reaction time on the functional groups and surface structure of nitrogen-doped graphite felt were studied. The surface morphology and defect, element content and surface chemical state of the modified electrode were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) test, Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). The electrochemical performance of the modified electrodes was evaluated by cyclic voltammetry, electrochemical impedance …

An In-Situ Raman Spectroscopic Study On The Interfacial Process Of Carbonate-Based Electrolyte On Nanostructured Silver Electrode, Yu Gu, Yuan-Fei Hu, Wei-Wei Wang, En-Ming You, Shuai Tang, Jian-Jia Su, Jun Yi, Jia-Wei Yan, Zhong-Qun Tian, Bing-Wei Mao

Journal of Electrochemistry

The solid-electrolyte interphase (SEI) plays a key role in anodes for rechargeable lithium-based battery technologies. However, a thorough understanding in the mechanisms of SEI formation and evolution remains a major challenge, hindering the rapid development and wide applications of Li-based batteries. Here, we devise a borrowing surface-enhanced Raman scattering (SERS) activity strategy by utilizing a size optimized Ag nanosubstrate to in-situ monitor the formation and evolution of SEI, as well as its structure and chemistry in an ethylene carbonate-based electrolyte. To ensure a reliable in-situ SERS investigation, we designed a strict air-tight Raman cell with a three-electrode configuration. Based on …

Isolation And Characterization Of Caffeine-Degrading Bacteria From Coffee Plantation Areas In Malaysia, Elvina Clarie Dullah, Mohd Fazli Farida Asras

Makara Journal of Technology

Decaffeination by microbial degradation is currently the most optimal and low-cost approach, involving only microbial cells and/or their enzymes. The bacterium was characterized using a series of biochemical tests. Positive results were obtained from carbohydrate fermentation, citrate utilization, and catalase tests, while negative results were obtained from Voges-Proskauer (VP) and indole tests. Three different caffeine concentrations of 0.25%, 0.4%, and 2% were tested and measured through Gas Chromatography-Mass Spectrophotometry (GC-MS) analysis. The highest caffeine reduction (89.25%) was found when 0.25% caffeine was used in the media. Only a small amount of caffeine was reduced to 0.4% and 2%, with 34.78% …

Optimization Of The Building Envelope And Roof Shading To Reduce The Energy Consumption Of College Low-Rise Buildings In Indonesia, Nasruddin Nasruddin, Azimil Gani Alam, Mohammad Imroz Sohel

Makara Journal of Technology

Energy consumption in buildings is a crucial concern globally, prompting researchers to explore innovative solutions to mitigate its impact. This study investigates the optimization of building envelopes and roof shading systems of existing buildings in Indonesia to realize notable energy savings. Multiple scenarios were explored, with modifications to building envelopes and roof shading, highlighting the overall thermal transfer value as a key parameter. Using EnergyPlus simulations, the efficacy of natural ventilation in corridors and roof shading modifications was assessed in reducing energy consumption. The findings revealed that renovating existing buildings by optimization of the building envelope and roof shading by …

Design, Fabrication And Characterization Of Zero Power Sensor/Harvester For Smart Grid Applications, Zeynel Guler

Mechanical Engineering ETDs

This study presents a flexible sensor/harvester device to be used in both electromagnetic sensing and energy harvesting applications for smart grids. When a current passes through a wire, the sensor detects the magnetic field created by that current. The sensor magnet interacts with the wire magnetic field resulting in a transfer of energy through the piezoelectric cantilever. Piezoelectric, conductive, magnetic, and magnetostrictive composite thin films were prepared to fabricate this device.

Initially, the magnet of the cantilever was optimized considering its shape, thickness, length, taper angle etc. via both simulations and experiments. Peak to peak voltage versus cantilever position graph …

Lif-Sn Composite Modification Layer To Modify Garnet/Lithium Metal Interface, Wu Yang, Xue-Fan Zheng, Yu-Qi Wu, Zheng-Liang Gong

Journal of Electrochemistry

The growing demands for electric vehicles and consumer electronics; as well as the expanding renewable energy storage market; have promoted extensive research on energy storage technologies with low costhigh energy density and safety. Lithium (Li) metal and solid-state electrolytes are considered as important components for next-generation batteries because of their great potential for improvements in energy density and safety performance. Inorganic garnet-type solid electrolytes with high Li-ion conductivity (about 10^-3 S·cm^-1) and high shear modulus (55 GPa) are considered to be ideal solid-state electrolytes; however; the issue of Li dendrite growth still obstructs their practical application. Herein; …

Constructing Carbon-Encapsulated Nifev-Based Electrocatalysts By Alkoxide-Based Self-Template Method For Oxygen Evolution Reaction, En-Hui Ma, Xu-Po Liu, Tao Shen, De-Li Wang

Journal of Electrochemistry

The development of green and sustainable water-splitting hydrogen production technology is beneficial to reducing the over-reliance on fossil fuels and realizing the strategic goal of "carbon neutral". As one of the half reactions for water splitting, oxygen evolution reaction has suffered the problems of sluggish four-electron transfer process and relatively slow reaction kinetics. Therefore, exploring efficient and stable catalysts for oxygen evolution reaction is of critical importance for water-splitting technology. Metal alkoxides are a series of compounds formed by the coordination function of metal ions with alcohol molecules. Metal alkoxides possess the double advantages of organic materials and inorganic materials, …