Materials Science and Engineering Commons^™

Effects Of Gypsum And Limestone On Early-Age Hydration And Strength Optimization In Belite Calcium Sulfoaluminate Cement, Sai Akshay Ponduru, Bryan K. Aylas-Paredes, Taihao Han, Advaith Neithalath, Narayanan Neithalath, Gaurav Sant, Aditya Kumar

Materials Science and Engineering Faculty Research & Creative Works

Belite calcium sulfoaluminate cement (CSAB), an alternative to Portland cement, exhibits excellent strength at both early and later ages. However, due to its high belite content, the carbon reduction from this type of cement is not sufficient when compared to other alternative cements. To further enhance CSAB's sustainability, this study investigates the performance of CSAB when partially replaced by low-carbon mineral additives (i.e., limestone and gypsum). The primary objective is to identify the optimal mixture design by incorporating gypsum and limestone to formulate a sustainable binder that maintains high compressive strength. The CSAB is replaced (with both additives) by up …

Effect Of Shrinkage-Mitigating Materials, Fiber Type, And Repair Thickness On Flexural Behavior Of Beams Repaired With Fiber-Reinforced Self-Consolidating Concrete, Jingjie Wei, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

While self-consolidating concrete (SCC) has emerged as a highly effective approach for the repair of concrete structures, there have been few investigations regarding the effect of the combination of different fiber and shrinkage-mitigating material types (shrinkage-reducing admixture, SRA; superabsorbent polymer, SAP; and expansive agent, EA) on the flexural behavior of repaired structures. This study aims to explore the influence of three different shrinkage-mitigating materials (1.25%–2.5 % SRA, 4%–8% EA, and 0.2%–0.4 % SAP), four fiber types (two macro synthetic fibers, MSFA and MSFB; 5D hooked steel fibers, 5D; a combination of 80 % 3D hooked steel +20 % short steel …

Optimizing And Validation Of Sustainable Uhpc With Waste Glass Powder Utilizing Modified Particle Packing Approach And Response Surface Methodology, Mohamed Taman, Elsaid Maaty, Alaa Mehrez, Ahmed Kamal Isaac

Journal of Engineering Research

The current study explores the potential of utilizing Waste glass powder (WGP) as an alternative to cement in the development of sustainable eco-friendly Ultra-high-performance concrete (UHPC). UHPC mixtures underwent optimization through the application of a Modified Andreasen and Andersen (MAA) particle packing model, resulting in a reduction of cement content from 900 to 800 kg/m³. Six mixes were cast, with varying levels of cement replacement ratios with WGP up to 50%. The evaluation focuses on the flowability, dry density, and mechanical properties of UHPC at different ages using normal curing. A statistical model utilizing response surface methodology (RSM) …

Integrating Off-Spec Scms Into Plc Blends, George A. Qubty

Civil Engineering Theses - Archive

Off-spec supplementary cementitious materials (SCMs) remain underutilized due to variability in reactivity and non-conformance with existing standards. This study evaluates the hydration behavior and fresh-state and mechanical performance of these materials in Portland limestone cement (PLC) systems. One Class F fly ash (FA), one bottom ash (BA), and two calcined clays (HACC and LACC) were evaluated as 20 % replacements to PLC. Hydration behavior was characterized using isothermal calorimetry and thermogravimetric analysis (TGA), while fresh-state and mechanical performance were assessed through flow table, Vicat setting time, load–crack mouth opening displacement (CMOD) flexural testing, and compressive strength testing. HACC increased compressive …

Corrosion Of Pipes In Soil Under Cathodic Protection, Ashley Chow

Williams Honors College, Honors Research Projects

This research project focuses on understanding how various soil properties affect the corrosion of buried pipelines that are protected by cathodic protection (CP) systems. Specifically, the study seeks to evaluate key soil characteristics, including resistivity, moisture content, and pH levels to determine their influence on the efficiency of CP systems in mitigating corrosion. Through controlled laboratory experiments, carbon steel specimens were exposed to a range of simulated soil conditions to mimic real-world environments. Corrosion rates were assessed using advanced electrochemical techniques, such as linear polarization resistance (LPR) and Tafel slopes, along with traditional mass loss methods. The primary objectives of …

Pla Polymer Binder In Core Production - Influence On Final Casting Dimensions, Artur Soroczyński, Krzysztof Rechowicz

Virginia Digital Maritime Center (VDMC) Faculty Publications

The foundry industry is seeking an ecological alternative to synthetic molding resins. This study evaluates the technological properties of core sands bonded with biodegradable polylactide (PLA). Cores prepared on a 2% quartz sand matrix were subjected to casting processes using two alloys with extremely different pouring temperatures: gray cast iron (approx. 1200 °C) and AK11 silumin (approx. 710 °C). The research methodology included macroscopic assessment, dimensional analysis using 3D scanning (GOM Inspect), and qualitative knock-out assessment supported by numerical temperature field simulation. The results showed that the high crystallization temperature of cast iron leads to complete thermal degradation of the …

Thermo-Rheological And Tribological Properties Of Low- And High-Oleic Vegetable Oils As Sustainable Bio-Based Lubricants, Abiodun Saka, Tobechukwu K. Abor, Anthony C. Okafor, Monday U. Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Vegetable oil-based lubricants have attracted increased research attention in recent decades as sustainable alternatives to conventional petroleum-based lubricants in metal machining. However, more studies are required to fully elucidate the thermo-rheological and tribological properties. This study presents an investigation of the thermo-rheological and tribological properties of different vegetable oils, including low- and high-oleic soybean oil, high-oleic sunflower, safflower, and canola oils. The lubricity, and evolution of viscosity and thermodynamic properties as a function of temperature were investigated to obtain important parameters including the viscosity index, flow behavior index, flow activation energy, specific heat capacity, thermal conductivity, coefficient of friction, contact …

Evaluating The Effectiveness Of Stay-In-Place Forms To Improve The Tosional Stability Of Box Beam Bridges During Erection, Karl E. Barth, Michael W. Seek, Gregory K. Michaelson, Dimitra Pyrialakou, Brook T. Woldegabriel

Engineering Technology Faculty Publications

Cold-formed tub girders provide an effective steel solution for short-span bridges. The girders are often delivered with an open top with stay-in-place forms installed on site. Walkways may be installed to the side of the girder that can induce significant torsion rotations in the open cross section. Full scale tests on girder specimens have shown that installing one or two panels of stay in place forms at the ends of the girder can significantly reduce the torsion rotation of the girder by providing warping resistance. Cantilever tests on the stay in place forms are performed to investigate the influence of …

Flexural Post-Cracking Performance Of Macro Synthetic Fiber Reinforced Super Workable Concrete Influenced By Shrinkage-Reducing Admixture, Jingjie Wei, Nima Farzadnia, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Most literature has focused on the effect of shrinkage-reducing admixture (SRA) in shrinkage mitigation resistance of concrete. This study aims to examine the impact of SRA on the efficiency of macro synthetic fibers (MSF) in enhancing the flexural post-cracking behavior of fiber-reinforced super workable concrete (FR-SWC). A comparative analysis of the influence of fiber combinations on the flexural post-cracking behavior of beams is also included. Results showed that a higher dosage of SRA, particularly at 5 % by mass of binder, had a noticeable negative impact on flexural post-cracking performance of beams while exhibiting positive effect on workability and shrinkage …

Coating Compositions And Methods For Using The Same, Fateme Razaei, Thomas P. Schuman, Glenn C. Morrison

Patents

Coating compositions and methods for using the same are disclosed. The coating compositions can include an aminosilica adsorbent. The coating compositions can adsorb CO2 .

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Ultrafast Belite (Β-C2s) Production Using Biofuel-Based Combustion Synthesis, Shubham Agrawal, Sayee Srikarah Volaity, Oluwadamilare Charles Adesina, Bryan K. Aylas-Paredes, Taihao Han, Srinivas Kilambi, Aditya Kumar, Narayanan Neithalath

Materials Science and Engineering Faculty Research & Creative Works

This study presents a novel low-temperature, combustion synthesis (CS) approach for the rapid production of belite-rich cements. CS leverages the exothermic heat released from the combustion of biofuels such as lignin and/or biomass, intermixed with pelletized limestone and quartz. At an imposed furnace temperature of ∼700°C (as opposed to 1200°C–1300°C required in a conventional kiln), the source materials are rapidly transformed to belite, resulting in energy, emissions, and economic benefits. This work explores the influence of various process parameters, viz., fuel types and contents, airflow rate, porosity, holding temperature, and holding time on the efficiency of CS-based belite synthesis. Through …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

Development Of Bio-Based Coating Materials For Environmentally Friendly Controlled-Release Nitrogen Fertilizer Applications, Anne Carolyne Mendonca Cidreira

Electronic Theses and Dissertations

No abstract provided.

Investigating The Effects Of Fly Ash On The Properties Of Silica-Deficient High Alumina Materials, Sai Akshay Ponduru

Doctoral Dissertations

This research is made up of five studies mainly focused on attaining sustainability in high alumina cements like calcium aluminate cement (CAC) and calcium sulfoaluminate belite cements (CSAB) by partially replacing them with additives and supplementary cementitious materials (SCMs) like fly ash (FA). The first study focused on understanding the reaction kinetics of CAC and FA binders at different replacement levels (i.e. between 10%-to-50% by mass) and their effect on mechanical properties. It was also shown that the reactive nature of FAs can be determined by calculating a single parameter called number of constraints (nc) derived from topological constraint theory. …

A Comparative Study Between Soft Structures And Hard Structures For The Protection Of Egypt’S Coastlines Against Climate Change, Donia Eldwib

Theses and Dissertations

Coastal communities worldwide face unprecedented threats from climate change, with rising sea levels, increased storm intensities, and accelerated coastal erosion posing significant risks. Egypt, with over 3,000 kilometers of coastlines along the Mediterranean and Red Seas, it is particularly vulnerable due to its densely populated and economically critical low-elevated coastal zones. With the Mediterranean Sea, and the Nile Delta specifically under huge threats, this study examines the different coastal protection strategies used to address these climate change impacts. Different coastal protection structures have been used throughout the years starting with the well-known hard structures moving on to greener alternatives such …

Capacity Of Self Compact Concrete Walls Using Attapulgite As A Partial Replacement Of Cement Under One Way And Two Way Action Restriction, Wissam Kadhim Alsaraj, Luma Abdul Ghani Zghair, Akhlas Hashem Mohammed

Al-Esraa University College Journal for Engineering Sciences

This investigation about the structural performance of sustainable self-compact concrete walls exposed to eccentric axial regularly dispersed loading, including the effect of aspect ratio (AR) and slenderness ratio (λ) by one-way and two-way action. The experimental program includes testing ten wall panels, the eccentricity of the loading system equivalent to one-sixth of depth. These wall panels are separated into four groups, each one consisting of three specimens. first and second groups clarify the aspect ratio (H/L) effect. The results indicated for decreasing AR from (0.75 to 0.625), (0.625 to 0.5), and (0.75 to 0.5), the increase of final load is …

Exploring The Benefits Of Feature Selection Based On Bat Algorithm And Deep Learning In Brain Cancer Diagnosis, Noor Fawzi Shafiq

Al-Esraa University College Journal for Engineering Sciences

Brain cancer is considered one of the most dangerous types that must be treated as soon as possible. Therefore, it is necessary to detect brain cancer in its early stages to enhance the diagnosis of the condition. This study proposes to combine the bat algorithm (BA) with deep learning methods to identify and classify brain tumors in medical images accurately.

In this paper, the bat algorithm was used to select distinctive features from the input brain images. The Bat Algorithm (BA) is a metaheuristic optimization algorithm that mimics the echolocation behavior of bats. It efficiently explores the feature space to …

Unveiling The Hidden Threat: How Wireless Networks Fuel Serious Cyber Attacks, Ibtesam Jomaa Hawi

Al-Esraa University College Journal for Engineering Sciences

The spread of wireless networks has led to an increase in serious cyber attacks due to their weak architecture. This article focuses on reevaluating cybersecurity in wireless network technology by integrating statistical information detection methods and artificial intelligence (AI) algorithms. To construct a wireless networking scenario that accurately reflects real-life conditions, we created a data fabrication that included four pre-existing anomalies as well as four newly introduced anomalies. The synthetic dataset created from these generation processes contains 20 thousand distinguishable values, which are later divided into training and validation sets. Using the strategy described before, we began to analyze the …

A Study On Improving The Accuracy And Effectiveness Of Similarity Detection Processes In Text Files Using Nlp Techniques, Noor Abdulmuttaleb Jaafar

Al-Esraa University College Journal for Engineering Sciences

The rapid expansion of the Internet has revolutionized access to information, especially in the area of unstructured data, most of which consists of textual content. While instant access to information brings many advantages, it has also given rise to a prevalent problem – plagiarism. Copying and reusing materials without proper permission poses a significant threat to academic integrity and integrity. Rates of plagiarism, especially in academic and scientific publications, have risen with the advent of the Internet, reaching alarming levels, such as 60% in student projects. This study examines the proposed model that includes computation of similarity using cosine coefficients, …

An Intelligent System Using Deep Learning For Healthcare Monitoring In Light Of The Covid-19 And Future Pandemics Based On Iot, Sara Salman Qasim, Rajaa J. Khanjar, Jamal Nasir Hasoon, Baesher Abdullateff Abad, Ali Hussein Fadil, Shajan.M. Alsowaidi

Al-Esraa University College Journal for Engineering Sciences

Recently, the Internet of Things has become a compelling research field as a new topic of research in various disciplines, particularly in the field of healthcare, because the Internet of Things is rebuilding modern healthcare systems by integrating technology, economics, and social perspectives. The development of healthcare systems from traditional to more personalized systems in which patients can be easily diagnosed, monitored and treated and many people can be helped. People are treated and cared for remotely and this is what some people need in the crisis the world has been through like COVID-19. This epidemic is caused by the …

Speech Coding Based On A Hybrid Approach: Dct, Huffman And Run-Length Coding, Sundos Abdulameer Alazawi, Esraa Jaffar Baker, Shahbaa Mohammed Abdulmaged

Al-Esraa University College Journal for Engineering Sciences

The exponential expansion of data in the digital world necessitates the development of effective methods for data transmission and storage. Data compression (DC) strategies are suggested to reduce the quantity of data stored or conveyed due to constrained resources. As a result of DC ideas' ability to efficiently use existing storage space and transmission capacity, different methods have been developed in various areas. Speech coding is a lossy method of coding; therefore, the output signal differs slightly from the input signal. Speech coding is useful for message encryption, communication over long distances and speech quality. In the fields of digital …

The Evolution Of The University Of Al-Anbar Urban Planning Based On The Mental Picture's Diversity And The Contemporary Planning Spaces Filling, Ali Abdulsamea Hameed

Al-Esraa University College Journal for Engineering Sciences

This research concentrated on the role of environmental graphic design (EGD) and the place-making idea in the interior environment of Al-Anbar University. To develop an identity being visual for the University of Al-Anbar internal environment (IE) is this goal of project. The search sought to create and enhance the shape of the internal University of Al-Anbar vacuum by reviving the idea of place building. In order to build and filling the internal emptiness of the campus, the identity being visual must also be strengthened. The descriptive analytical approach was chosen since it was best suited to achieve the goal of …

Optimization Of Construction Scheme Of Ultra‑Large Special‑Shaped Foundation Pit Adjacent To Existing Station And Temporary Steel Bridge, Chen Dengwei

Journal of China & Foreign Highway

With the intensifying development density of urban underground space in China，the impact of ultra-large foundation pit construction on the normal operation of adjacent structures cannot be ignored.Relying on the Huangmugang Comprehensive Transportation Hub Project in Shenzhen，this paper studied the deformation of the envelope structure and soil caused by the excavation of the ultra-large special-shaped foundation pit，as well as the structural response of the deformation of the adjacent existing station and the temporary steel bridge.The paper optimized the construction scheme of the special-shaped foundation pit excavation.The results show that the deformation trend of the envelope structure on the north and south …

Comparison Analysis Of Different Settlement Prediction Models Under Small Post‑ Constructio N Load On Soft Foundation, Han S Hanpeng, Fu Wei, Zhang Junhui, Lin Chen

Journal of China & Foreign Highway

Settlement deformatio n is a key conc ern in soft foundation construction.Since there is still a small load applied after the filling of soft foundation in the actual project,based on the settlement monitoring data of the high-fill section of Zhaoyang West Ring Expressway in Zhaotong City,Yunnan Province,three settlement prediction methods,namely the hyperbolic method,the three-point method,and the Hoshino method,were used to predict,compare,and analyze the settlement of the fill foundation,and the fitting characteristics of each model were summarized.By comparing the fitting curves and the actual settlement curves,it was found that the loading on the roadbed will cause large errors in the prediction …

Experimental Study On Deformation Characteristics Of High Liquid Limit Soil Considering The Effect Of Temperature, Li Bangwu, Shen Xuning, Zhang Rui, Chen Yanrong

Journal of China & Foreign Highway

In order to study the influence of temperature on the absorbed bound water and deformation characteristics of high liquid limit soil，the high liquid limit soil in Hunan and Hainan provinces were selected for test.The influence of temperature on the content of bound water was measured by a temperature-controlled water bath volumetric flask test.The consolidation test was carried out on the samples with a one-dimensional temperature-controlled consolidometer，and the variation law of high liquid limit soil deformation affected by temperature was analyzed under the modified pore ratio considering the bound water content.The results show that the absorbed bound water in the high …

Research Progress Of Rubber‑Modified Asphalt By Wet Process, Ge Dongdong, Jiang Xiangyang, Lyu Songtao, Zhang Honggang, Song Xiaojin

Journal of China & Foreign Highway

The application of waste tires in asphalt pavements can not only effectively reduce resource consumption but also significantly reduce environmental pollution.Crumb rubber could be obtained by processing waste tires and used as a modifier by mixing with asphalt through the wet process to improve the performance of asphalt.This paper reviewed the research progress of rubber-modified asphalt by wet process and discussed its preparation process，influencing factors of performance，and modification mechanism.By reviewing the relevant studies，the critical conditions in the preparation process and their effects on storage stability were summarized.Furthermore，the effects of rubber dosage，particle size，matrix asphalt type，and preparation parameters on the physical and …

Friction‑ 1d Transformer ： A 1d Vision Transformer Hybrid Model For Skid Resistance Prediction On Asphalt Pavements, Pei Feifei, Nie Zilong, Xu G Uomin, Zhan You, Gong Xianqi, Ai Changfa, Deng Yuan, Ji Zhengyun, Wang Shifa

Journal of China & Foreign Highway

The friction performance of road surfaces is an important indicator of highway safety，which is closely related to road texture.In this paper，a set of three-dimensional denoising methods for road texture data with different noise levels was proposed，which could effectively remove noise while preserving local texture features.In addition，a skid resistance prediction model named Friction- 1D Transformer was developed based on the design concept of Vision Transformer （VIT） for skid resistance evaluation of asphalt pavements.Unlike traditional convolutional neural networks，the Friction- 1D Transformer utilized positional encoding structures and multi-head attention mechanisms to extract global features from one-dimensional （1D） texture signals along the direction of …