Materials Science and Engineering Commons^™

Electrochemical Voltammetric Behavior Of Sulfur Mustard On The Bare Pt Electrode, Yu-Lin Yang, Jie Sun, Tian Zhou, Ji-Gang Li, Shou-Ping Wei

Journal of Electrochemistry

The sulfur mustard (bis(2-chloroethyl) sulphide, HD), one of highly toxic chemical weapon agents, can damage the alive tissue cells (such as skin, lung, respiratory mucosa and so on), and cause carcinogenic and mutagenic effects for a long time exposure, which imposes a great threat not only to the human health, but also to the sustainable development of the society. With its convenience, high sensitivity and rapid response, electrochemical technology exhibits considerable potential in the field-deployed detection toward HD, but the related reports are rare. Herein, the electrochemical behavior of HD on the bare Pt electrode was investigated by electrochemical measurements, …

Electrocatalytic "Volcano-Type" Effect Of Nano-Tio2 (A)/(R) Phase Content In Pt/Tio2-CnX Catalyst, Ai-Lin Cui, Yang Bai, Hong-Ying Yu, Hui-Min Meng

Journal of Electrochemistry

The relationship between the electrochemical activity of fuel cell catalysts and Pt particle size, as well as the catalyst support and co-catalyst is still unclear. In this work, FESEM, XRD, BET, TEM and CV techniques were adopted to investigate the effects of TiO₂ anatase (A)/rutile (R) phases content on the electrochemical activity of Pt electrocatalyst. The results showed that the anatase-rutile phase transformation occurred during the heat treatment of TiO₂ at 700 ~ 900 ^oC accompanied by the growth of two-phase crystalline size, and anatase was completely transformed into rutile at 900 ^oC. TEM results revealed …

Effect Of Chloride Ion On Electrochemical Behavior Of Silver Electrodeposition In Chcl-Urea Low Eutectic Solvent, Chong-Bo Zhan, Run-Jia Zhang, Xu Fu, Hai-Jing Sun, Xin Zhou, Bao-Jie Wang, Jie Sun

Journal of Electrochemistry

Metallic silver coating has been widely used in the fields of microelectronics industry, catalyst, sensor and preparation of magnetoresistive materials because of its excellent corrosion resistance, good lubricity, high conductivity, excellent decoration and high catalysis. Compared with the traditional aqueous solution system, the research on metal electrodeposition in ionic liquid system is developing rapidly. In addition, additives are the key factors in the silver plating process. Adding a small amount of organic or inorganic additives to the plating solution will significantly change the coating properties, such as improving brightness, hardness and ductility. In this paper, using choline chloride urea (ChCl-Urea) …

Simultaneous Hydrogen And (Nh4)2So4 Productions From Desulfurization Wastewater Electrolysis Using Mea Electrolyser, Ju-Cai Wei, Lin Shi, Xu Wu

Journal of Electrochemistry

It is preferred to simultaneously recover resource and energy from waster. Sulfur dioxide, SO₂, a common air pollutant, a potential energy resource, is a key link to sulfur nature circulation. SO₂ can be conversed to NH₄HSO₃ and (NH₄)₂SO₃ during the ammonia desulfurization process, which can be used to produce (NH₄)₂SO₄ fertilizer. For high quality (NH₄)₂SO₄ fertilizer and high heat transfer efficiency of the evaporative crystallization, HSO₃^- or SO₃^2- needs to be oxidized to form SO …

Study And Improvement On Expansion Property Of Silicon Oxide, Wei-Chuan Qiao, Fang-Ru Li, Jin-Lin Xiao, Li-Juan Qu, Xiao Zhao, Meng Zhang, Chun-Lei Pang, Zi-Kun Li, Jian-Guo Ren, Xue-Qin He

Journal of Electrochemistry

The silicon-based anode materials have the potential to meet the ever-increasing demand for energy density in lithium-ion batteries market owing to their high theoretical specific capacity. Unfortunately, their commercialization was hindered by the continuous volume expansion. Herein, the expansion characteristics and corresponding mechanism of the silicon oxide and graphite-silicon oxide composites were investigated by in-situ displacement detection systematically. The results showed that the expansion property was improved by material process modifications. During the de/lithiation processes of graphite, the expansion ratio in 30% ~ 50% SOC changed little because of the small interlayer spacing variation of the intercalated graphite. …

Preparation And Properties Of Gcp-Supported Palladium Particles Composite Towards Electrochemical Ammonia Synthesis, Ying-Chao Wang, Zi-Zai Ma, Yi-Fan Wu, Xiao-Guang Wang

Journal of Electrochemistry

Ammonia (NH₃) plays an essential role in agriculture and modern industries. Electrochemical fixation of nitrogen (N₂) to ammonia (NRR) under ambient conditions with renewable electricity is a promising strategy to replace the industrial Haber-Bosch method. However, it usually suffers from extremely poor ammonia yield and low Faraday efficiency due to the poor electrocatalysts. Therefore, intensive studies have been devoted to developing efficient NRR catalysts till now. Among them, palladium (Pd) can capture protons in the aqueous phase to form stable α-PdH, which balances the competitive adsorption between nitrogen and protons as well as reduces the …

A Modular Synthesis Of Processable And Thermally Stable Semi-Fluorinated Aryl Ether Polymers Via Step-Growth Polymerization Of Fluoroalkenes, Ketki Eknath Shelar

Theses and Dissertations

Tailored fluoropolymers remain the leading choice for a wide variety of advanced high-performance applications, including electronic/optical and energy conversion, owing to their unique blend of complementary high-performance properties. Amorphous semi-fluorinated polymers exhibit improved solubility and melt processability when compared to traditional perfluoropolymers. A leading class of semi-fluorinated aryl ether polymers includes perfluorocyclobutyl (PFCB), perfluorocycloalkenyl (PFCA), and fluoroarylene vinylene ether (FAVE) polymers. Monomers containing aromatic trifluorovinyl ethers (TFVE) are used to synthesize PFCB polymers via radical-mediated [2+2] cyclodimerization. On the other hand, FAVE and PFCA polymers are polymerized via base-mediated nucleophilic addition/elimination of bisphenols with TFVE monomers and decafluorocyclohexene respectively. The …

Relating Detonation Parameters To The Detonation Synthesis Of Silicon Carbide, Martin Langenderfer, Eric W. Bohannan, Jeremy Lee Watts, William Fahrenholtz, Catherine E. Johnson

Chemistry Faculty Research & Creative Works

Detonation synthesis of silicon carbide (SiC) nanoparticles from carbon liberated by negatively oxygen balanced explosives was evaluated in a 23 factorial design to determine the effects of three categorical experimental factors: (1) cyclotrimethylene-trinitramine (RDX)/2,4,6-trinitrotoluene (TNT) ratio, (2) silicon (Si) additive concentration, and (3) Si particle size. These factors were evaluated at low and high levels as they relate to the detonation performance of the explosive and the solid Si-containing phases produced. Detonation velocity and Chapman-Jouguet (C-J) detonation pressure, which were measured using rate stick plate dent tests, were evaluated. Solid detonation product mass, silicon carbide product concentration, and residual silicon …

Structural, Charge Transport, Gas Sensing, Magnetic, Pseudocapacitive, And Electrocatalytic Properties Of Perovskite Oxides., Surendra Bahadur Karki

Electronic Theses and Dissertations

Perovskites are functional materials with the general formula ABO₃ (A = alkali, alkaline earth or lanthanoid cations and B = transition metal or main group cations). These materials are marked by a variety of crystal structures and interesting properties such as colossal magnetoresistance, ferroelectricity, multiferroicity, superconductivity, pseudocapacitance, gas sensing, charge transport, and electrocatalytic properties. The formula of perovskite can be written as AA’BB’O₆, when there is ordering between two cations over A and B-sites. Such compounds are called double perovskite oxides. Some amount of oxygen could be lost from crystal structure without decomposition of the phase. Such …

Extractive Membranes For The Detection And Screening Of Waterborne Plutonium, James Foster

All Dissertations

The development of rapid screening tools for special nuclear materials remains a crucial focus for nonproliferation efforts. Traditional approaches for the analysis of trace-level Pu isotopes in water requires tedious and time-consuming sample preparation steps that do not lend well to expeditious screening. Therefore, a novel analytical method that combines both Pu concentration and source preparation into a single detection system would make for an invaluable tool for nuclear security applications. Extractive membranes absorbers can help to fulfill this role as they are capable of concentrating Pu to detectable limits while subsequently serving as alpha spectrometry sample sources. In Chapter …

Synthesis And Molecular Processes Governing Self-Healing Polymeric Materials, Siyang Wang

All Dissertations

Self-healing polymers capable of recovering from physical damages are promising materials for advanced technologies. In these studies, we developed routes to achieve self-healable properties in acrylic-based copolymers that rely on non-covalent dipolar interactions present in essentially all polymeric materials. Using a combination of spectroscopic tools, thermo-mechanical analysis, and molecular dynamic (MD) simulations, these studies have shown that dipolar interactions lead to conformational changes of macromolecular segments which, in turn, result in self-healing without external intervention. This dissertation also describes the development of novel self-healable acrylic-based covalent adaptable networks (CANs) that combine reprocessing and self-healing properties. The utilization of dipolar interactions …

Investigation On Electrochemical Processes Of P-Aminothiophenol On Gold Electrode Of Nanostructures, Hui-Yuan Peng, Jia-Zheng Wang, Jia Liu, Huan-Huan Yu, Jian-De Lin, De-Yin Wu, Zhong-Qun Tian

Journal of Electrochemistry

Electrochemical reactions on nanostructured noble electrodes have received much attention, however, the reaction mechanism and reaction kinetics are still difficult to be studied. Probe molecule can give an insight to the investigation of electrochemical reactions on noble electrodes with nanostructures. In this paper, the electrochemical process of p-aminothiophenol (PATP) adsorbed on the gold electrode was studied by electrochemical cyclic voltammetry and surface-enhanced Raman spectroscopy (SERS). Here, we used one-step sodium citrate reduction method (Frens method) to synthesize gold nanoparticles, which are used to construct the nanostructured gold electrode. The Raman electrolytic cell used was based on the traditional three-electrode electrolytic …

Study On Electrochemical Conversion Of Ammonium Sulfate To Ammonium Persulfate In Acetylpyrazine Wastewater, Yi-Jie Wang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

Acetylpyrazine is an important spice and also plays important roles in biology, medicine and other fields. However, the wastewater containing ammonium persulfate, ferric ion (Fe³⁺), pyrazine, and a large amount of ammonium sulfate was produced during the production of acetylpyrazine. In this study, ammonium sulfate in acetylpyrazine wastewater was electrolytically converted into ammonium persulfate for economic benefits. Using platinum as an anode and graphite as a cathode, the influence factors of the electrolysis process (including the composition of the anolyte, the current density, the temperature, etc.) were firstly investigated without interference from other compositions. Under the optimal condition, …

Study On Electrodeposition Of Antimony In Choline Chloride-Ethylene Glycol Eutectic Solvent, Hao Wang, Xiao-Zhou Cao, Xiang-Xin Xue

Journal of Electrochemistry

Antimony is a chemically stable metal that has been widely used in industry, military and other fields. The use of electrodeposition to prepare antimony coating has the advantages of simple operation and low cost. The deep eutectic solvent (DES) is a eutectic mixture composed of a hydrogen bond donor and a hydrogen bond acceptor at a fixed molar ratio. It has the advantages of wide electrochemical window, high thermal stability, easy preparation, and low cost. Selecting DES as the electrolyte for electrodeposition can avoid the hydrogen evolution reaction of the aqueous system and the toxicity of ionic liquids. In recent …

Adjusting The Alloying Degree Of Pt3Zn To Improve Acid Oxygen Reduction Activity And Stability, Tian-En Zhang, Ya-Ni Yan, Jun-Ming Zhang, Xi-Ming Qu, Yan-Rong Li, Yan-Xia Jiang

Journal of Electrochemistry

Proton exchange membrane fuel cell (PEMFC) is a new type of energy device, a relatively excellent way to achieve carbon neutrality. However, due to the relatively slow reaction rate of oxygen reduction reaction (ORR) at the cathode, platinum (Pt) is the key material of the cathode catalyst. However, Pt is a kind of noble metal, and its high cost restricts the PEMFC commercialization process. At present, the main approach is to combine transition metals with Pt to prepare Pt-based alloys and to reduce the use of Pt. Pt-based alloys are excellent catalysts for ORR, improving both the activity and stability, …

Effects Of Electrode Shape On Lithiation Process Of Lithium-Ion Battery Electrodes, Shi-Wei Sun, Jian-Jun Nie, Yi-Cheng Song

Journal of Electrochemistry

This paper studies the influence of electrode shape on the lithiation process of lithium ion batteries. Both experimental observation and numerical simulation are employed to investigate the competitive interaction between the diffusion of lithium ions in both solid and liquid phases and the lithium intercalation reaction at the electrode surface. Experimental cells were prepared with the anode and cathode being placed parallel, leaving the latter embracing the former. An experimental device based on CCD camera was set up for in situ observation of electrode lithiation. The lithiation levels of the graphite anodes were estimated according to the observed color profile. …

Preparation Of Pt@Basrtio3 Nanostructure And Its Properties Towards Photoelectrochemical Ammonia Synthesis, Jing Zhang, Rui-Xia Guo, Jian-Jun Fu, Shi-Bin Yin, Pei-Kang Shen, Xin-Yi Zhang

Journal of Electrochemistry

Ammonia is an important industrial raw material and a potential green energy. Using renewable energy to convert nitrogen into ammonia under ambient condition is an attractive method. However, the development of efficient photoelectrochemical ammonia synthesis catalysts remains a challenge. Perovskite such as BaSrTiO₃ (BST) is a good photocatalytic material. However, BST is active under ultraviolet light and has a high recombination rate of photogenerated electron-hole pairs. By dispersing precious metals, it can effectively regulate the absorption of sunlight by BST. In this work, we used a two-step method to prepare BST. The H₂PtCl₆·6H₂O …

Multi-Scale Simulation Revealing The Decomposition Mechanism Of Electrolyte On Lithium Metal Electrode, Yan-Yan Zhang, Yue Liu, Yi-Ming Lu, Pei-Ping Yu, Wen-Xuan Du, Bing-Yun Ma, Miao Xie, Hao Yang, Tao Cheng

Journal of Electrochemistry

Lithium metal is considered as an ideal anode material for next-generation high energy density batteries with its high specific capacity and low electrode potential. However, the high activity of lithium metal can lead to a series of safety issues. For example, lithium metal will continuously react chemically with the electrolyte, forming unstable the solid electrolyte (SEI) films. In addition, lithium dendrites can be formed during cycling, which can puncture the SEI film and cause short circuits in the battery. These drawbacks greatly hinder the commercial application of lithium metal. To solve the above problems, it is important to understand the …

Controlling Unequal Surface Energy Results Caused By Test Liquids: The Case Of Uv/O3 Treated Pet, Bilge N. Altay, Paul D. Fleming, Md Arifur Rahman, Alexandra Pekarovicova, Bruce Myers, Cem Aydemir, Arif Karademir

Articles

Ultraviolet/ozone (UV/O3) treatment has been reported to be an effective method to modify properties such as wettability, adhesion or adsorption of plastic surfaces. The change in the surface is measured by contact angle analysis, which employs liquids and their surface tensions (ST) to estimate the surface energy (SE). We found two different practices in the scientific community: (1) the majority of researchers adopted the ST value of liquids from the literature, while (2) other researchers conducted real-time measurements in the lab under ambient conditions prior to SE estimation. To the best of our knowledge, there is no study that compares …

Metal Complexes Of Redox Active Ligands, Alexandra Chaparro, Parker Keller

Chemistry & Biochemistry Student Scholarship

Alexandra Chaparro ’22, Major: Biochemistry

Parker Keller ’24, Major: Chemistry

Mentor: Dr. Maria Carroll, Chemistry and Biochemistry

Our research focuses on synthesizing and studying the properties of metal complexes that contain redox active ligands. Ligands are molecules or ions that can bind to a metal ion, and this particular class of ligands is interesting because they can either accept or lose electrons. We synthesized zinc complexes, in order to measure the reduction potentials of the ligands, which provide information about the ease with which they accept electrons. We then synthesized iron complexes and determined their structures. These complexes are potentially …

Simplified Synthesis Of Conjugated Polymers Enabled Via 1,4-Dihydropyrrolo[3,2-B]Pyrrole, Kenneth-John Jack Bell

Master of Science in Chemical Sciences Theses

Conjugated polymers have attracted significant attention as the active layer material in organic electronics, such as organic photovoltaics and light-emitting diodes, partly due to the ability to influence a broad range of properties through structural design motifs. However, high performance conjugated polymers suffer from numerous synthetic steps, generation of toxic waste, and harsh reaction conditions all of which impart additional costs that inhibit their widespread utilization. Therefore, an emphasis on reducing synthetic complexity and utilizing abundant, commercially available starting materials is needed for organic electronics to reach their full potential. Dihydropyrrolo[3,2-b]pyrrole (H₂DPP) chromophores offer a simple one-pot synthesis …

Limits Of Detection Of Mycotoxins By Laminar Flow Strips: A Review, Xinyi Zhao, Hugh Byrne, Christine M. O’Connor, James Curtin, Furong Tian

Articles

Mycotoxins are secondary metabolic products of fungi. They are poisonous, carcinogenic, and mutagenic in nature and pose a serious health threat to both humans and animals, causing severe illnesses and even death. Rapid, simple and low-cost methods of detection of mycotoxins are of immense importance and in great demand in the food and beverage industry, as well as in agriculture and environmental monitoring, and, for this purpose, lateral flow immunochromatographic strips (ICSTs) have been widely used in food safety and environmental monitoring. The literature to date describing the development of ICSTs for the detection of different types of mycotoxins using …

Theranostic Copolymers Neutralize Reactive Oxygen Species And Lipid Peroxidation Products For The Combined Treatment Of Traumatic Brain Injury, Aaron Priester, Richard Waters, Ashleigh Abbott, Krista Hilmas, Klaus Woelk, Hunter A. Miller, Aria W. Tarudji, Connor C. Gee, Brandon Mcdonald, Forrest M. Kievit, Anthony J. Convertine

Chemistry Faculty Research & Creative Works

Traumatic brain injury (TBI) results in the generation of reactive oxygen species (ROS) and lipid peroxidation product (LPOx), including acrolein and 4-hydroxynonenal (4HNE). The presence of these biochemical derangements results in neurodegeneration during the secondary phase of the injury. The ability to rapidly neutralize multiple species could significantly improve outcomes for TBI patients. However, the difficulty in creating therapies that target multiple biochemical derangements simultaneously has greatly limited therapeutic efficacy. Therefore, our goal was to design a material that could rapidly bind and neutralize both ROS and LPOx following TBI. To do this, a series of thiol-functionalized biocompatible copolymers based …

Block Copolymer Directed Self-Assembly: Exploring The Efficacy Of Applications In Semiconductor Fabrication, Jakin Bryce Delony

USF Tampa Graduate Theses and Dissertations

Over the course of the past 80 years, semiconductor devices have become increasingly ubiquitous in everyday life.From constructing mainframes that encompassed entire rooms during the 1940s, to inventing personal computers in the 1980s, to developing progressively faster smartphones and wearable technology in the 2010s, the primary driving force behind the Digital Revolution has been increasing transistor counts, and thus computing power, via incremental improvements in optical lithography. In 1965, Intel co-founder Gordon Moore boldly predicted that the transistor density of semiconductor devices would double approximately every 18-24 months. While this prediction -- now colloquially referred to as Moore's Law -- …

In Situ Characterization Of Electrode Structure And Catalytic Processes In The Electrocatalytic Oxygen Reduction Reaction, Ya-Chen Feng, Xiang Wang, Yu-Qi Wang, Hui-Juan Yan, Dong Wang

Journal of Electrochemistry

As an electrochemical energy conversion system, fuel cell has the advantages of high energy conversion efficiency and high cleanliness. Oxygen reduction reaction (ORR), as an important cathode reaction in fuel cells, has received extensive attention. At present, the electrocatalysts are still one of the key materials restricting the further commercialization of fuel cells. The fundamental understanding on the catalytic mechanism of ORR is conducive to the development of electrocatalysts with the enhanced activity and high selectivity. This review aims to summarize the in situ characterization techniques used to study ORR. From this perspective, we first briefly introduce the advantages of …

An Additive Incorporated Non-Nucleophilic Electrolyte For Stable Magnesium Ion Batteries, Mao-Ling Xie, Jun Wang, Chen-Ji Hu, Lei Zheng, Hua-Bin Kong, Yan-Bin Shen, Hong-Wei Chen, Li-Wei Chen

Journal of Electrochemistry

Non-nucleophilic electrolytes are promising next-generation highly stable electrolytes for magnesium-ion batteries (MIBs). However, a passivation layer on Mg metal anode usually blocks Mg²⁺ diffusion, leading to poor reaction kinetics and low Coulombic efficiency of the Mg plating/stripping in these electrolytes. Here we explore the utilization of phenyl disulfide (PDF) as a film-forming additive for non-nucleophilic electrolytes to regulate the interfacial chemistry on Mg metal anode. Phenyl-thiolate generated from the PDF additive was found to suppress the unfavorable surface blocking layer, resulted in a high Coulombic efficiency of up to 99.5% for the Mg plating/stripping process as well as a …

Synchrotron X-Rays Characterizations Of Metal-Air Batteries, Ya-Jie Song, Xue Sun, Li-Ping Ren, Lei Zhao, Fan-Peng Kong, Jia-Jun Wang

Journal of Electrochemistry

The rapid development of electric vehicles urgently requires high-energy-density batteries. Recently, metal-air batteries have attracted much attention in industry and academia for their ultra-high theoretical energy densities. However, the practical application of metal-air batteries is severely impeded by multiple drawbacks, including severe side reactions, low energy efficiency, and limited cycle life. Understanding the reaction mechanism of the cell and further developing effective strategies are beneficial for the practical application of metal-air batteries. In the past decade, advanced characterization techniques have accelerated the development of metal-air batteries. In particular, synchrotron radiation-based characterization techniques have been widely applied to the mechanistic study …

In-Situ/Operando57Fe Mössbauer Spectroscopic Technique And Its Applications In Nife-Based Electrocatalysts For Oxygen Evolution Reaction, Jafar Hussain Shah, Qi-Xian Xie, Zhi-Chong Kuang, Ri-Le Ge, Wen-Hui Zhou, Duo-Rong Liu, Alexandre I. Rykov, Xu-Ning Li, Jing-Shan Luo, Jun-Hu Wang

Journal of Electrochemistry

The development of highly efficient and cost-effective electrocatalysts for the sluggish oxygen evolution reaction (OER) remains a significant barrier to establish effective utilization of renewable energy storage systems and water splitting to produce clean fuel. The current status of the research in developing OER catalysts shows that NiFe-based oxygen evolution catalysts (OECs) have been proven as excellent and remarkable candidates for this purpose. But it is critically important to understand the factors that influence their activity and underlying mechanism for the development of state-of-the-art OER catalysts. Therefore, the development of in-situ/operando characterizations is urgently required to detect key intermediates along …

Rational Design Of Electrochemical Molecular Probes For Highly Selective And Long-Term Measurement In Vivo, Yue Wang, Li-Min Zhang, Yang Tian

Journal of Electrochemistry

Designing electrochemical interfaces for in vivo analysis of neurochemicals with high selectivity and long-term stability is vital for monitoring dynamic variation and dissecting the complex mechanisms of pathogenesis in living animals. This review focuses on the development of electrochemical interfaces based on rational design of molecular probes for in vivo measurement with high selectivity and high stability from three aspects: (1) Specific recognition probes were rationally designed and created to remarkably improve the selectivity of in vivo analysis in a complicated brain environment. (2) The Au-C≡C functionalized surface was developed to remarkably enhance the stability of molecular assembly, and employed …

Discussion Of Materials Science Development Trend Through Climate Change, Manufacturing Update, National Security And Materials Genome Initiative, Weijian Lin, Bowen Zhang, Weihua Wang

Bulletin of Chinese Academy of Sciences (Chinese Version)

New materials are considered as the foreguide and the base of the revolution of advanced technology. Its development and trend of new materials greatly influences the human life and society development. Nowadays, the risk of climate change is increasing day by day, the pressure of manufacturing update of new technology revolution is bigger than ever, the competition and the friction between countries become more and more intense, and the iteration of advanced materials turns to a rigid demand. In this work, we analyze and predict the development tread of material from the aspects of climate change, manufacturing update, national security, …