Materials Science and Engineering Commons^™

Data-Driven Viewpoint For Developing Next-Generation Mg-Ion Solid-State Electrolytes, Fang-Ling Yang, Ryuhei Sato, Eric Jian-Feng Cheng, Kazuaki Kisu, Qian Wang, Xue Jia, Shin-Ichi Orimo, Hao Li

Journal of Electrochemistry

Magnesium (Mg) is a promising alternative to lithium (Li) in solid-state batteries due to its abundance and high theoretical volumetric capacity. However, the sluggish Mg-ion conduction in the lattice of solid-state electrolytes (SSEs) is one of the key challenges that hamper the development of Mg-ion solid-state batteries. Though various Mg-ion SSEs have been reported in recent years, key insights are hard to be derived from a single literature report. Besides, the structure-performance relationships of Mg-ion SSEs need to be further unraveled to provide a more precise design guideline for SSEs. In this Viewpoints article, we analyze the structural characteristics of …

Professor Yong Yang, The Editorial Board Member Of Journal Of Electrochemistry, Is Elected As A Fellow Of The Electrochemical Society, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Kai Wu, The Editorial Board Member Of Journal Of Electrochemistry And Chief Scientist Of Catl, Receives The National Science And Technology Progress Award, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Sorbitol-Electrolyte-Additive Based Reversible Zinc Electrochemistry, Qiong Sun, Hai-Hui Du, Tian-Jiang Sun, Dian-Tao Li, Min Cheng, Jing Liang, Hai-Xia Li, Zhan-Liang Tao

Journal of Electrochemistry

The unstable zinc (Zn)/electrolyte interfaces formed by undesired dendrites and parasitic side reactions greatly hinder the development of aqueous zinc ion batteries. Herein, the hydroxy-rich sorbitol was used as an additive to reshape the solvation structure and modulate the interface chemistry. The strong interactions among sorbitol and both water molecules and Zn electrode can reduce the free water activity, optimize the solvation shell of water and Zn²⁺ ions, and regulate the formation of local water (H₂O)-poor environment on the surface of Zn electrode, which effectively inhibit the decomposition of water molecules, and thus, achieve the thermodynamically stable …

Series Reports From Professor Wei’S Group Of Chongqing University: Advancements In Electrochemical Energy Conversions (1/4): Report 1: High-Performance Oxygen Reduction Catalysts For Fuel Cells, Fa-Dong Chen, Zhuo-Yang Xie, Meng-Ting Li, Si-Guo Chen, Wei Ding, Li Li, Jing Li, Zi-Dong Wei

Journal of Electrochemistry

Two major challenges, high cost and short lifespan, have been hindering the commercialization process of low-temperature fuel cells. Professor Wei’s group has been focusing on decreasing cathode Pt loadings without losses of activity and durability, and their research advances in this area over the past three decades are briefly reviewed herein. Regarding the Pt-based catalysts and the low Pt usage, they have firstly tried to clarify the degradation mechanism of Pt/C catalysts, and then demonstrated that the activity and stability could be improved by three strategies: regulating the nanostructures of the active sites, enhancing the effects of support materials, and …

First Announcement Of 76th Annual Meeting Of The International Society Of Electrochemistry, International Society Of Electrochemistry (Ise)

Journal of Electrochemistry

No abstract provided.

Tribocorrosion And Metal Release From Austenitic Stainless Steels 304 And 201 In Simulated Cassava Food Contact, Robert Addai, Temitope E. Olowoyo, Thalia E. Standish, Jeffrey Daniel Henderson, Ubong Eduok, Yolanda Hedberg

Chemistry Publications

Cassava is the third most significant calorie source in the tropics. Its processing has changed from traditional methods to stainless steel processing machines. This study investigated the influence of cassava on metal release from two common stainless steels, ASTM 304 and 201, with and without friction, and on tribocorrosion (multianalytically) of 304. Cassava was relatively corrosive and hindered repassivation of the surface oxide of stainless steel, but it also acted as a lubricant against mechanical friction. The combined action of friction and cassava caused a significant increase in iron, chromium, nickel, and manganese release from the stainless steels (30–35- fold …

Poly(Thioether) Thermosets With Gated Photodegradation, Surabhi Jha

Dissertations

Photodegradable polymer networks are attractive due to the precise spatiotemporal control and large-area applicability of light. Chemical linkages that enable these polymer networks to be photo-responsive, also hinder their applicability in ambient light. Photostable and photodegradable networks have recently been reported to overcome this challenge by combining other stimuli with light for degradation. We report the design of a network that responds to a simultaneous, dual stimulus for photodegradation. We design poly(thioether acetal) networks with benzylidene acetal moieties that are known to undergo β-scission in the presence of free thiols. By blocking these free thiols with a thermally labile protecting …

Carbon-Based Nanocomposite Membranes For Membrane Distillation: Progress, Problems And Future Prospects, Chhabilal Regmi, Yuwaraj K. Kshetri, S. Ranil Wickramasinghe

Chemical Engineering Faculty Publications and Presentations

The development of an ideal membrane for membrane distillation (MD) is of the utmost importance. Enhancing the efficiency of MD by adding nanoparticles to or onto a membrane’s surface has drawn considerable attention from the scientific community. It is crucial to thoroughly examine state-of-the-art nanomaterials-enabled MD membranes with desirable properties, as they greatly enhance the efficiency and reliability of the MD process. This, in turn, opens up opportunities for achieving a sustainable water–energy–environment nexus. By introducing carbon-based nanomaterials into the membrane’s structure, the membrane gains excellent separation abilities, resistance to various feed waters, and a longer lifespan. Additionally, the use …

Surface Structures And Properties Of High-Voltage Licoo2: Reviews And Prospects, Jian-Jun Fang, Yu-Hao Du, Zi-Jian Li, Wen-Guang Fan, Heng-Yu Ren, Hao-Cong Yi, Qing-He Zhao, Feng Pan

Journal of Electrochemistry

Nowadays, the development of high-voltage LiCoO₂ (lithium cobalt oxide, LCO) cathodes has attracted the widespread attention from both the academic and industry fields. Among the multiple concerns, researches on the surface issues would provide the most effective performance optimization pathway for the synthesis of high-voltage LCO. In this work, the issues of high-voltage LCO, including the phase transitions and crack formation, the oxygen redox related issues and side reactions, as well as the surface structure degradation, have been systematically reviewed. Then, we further clarify the surface modulations, and the interplay between the surface modulation and electrolyte tuning. Finally, we …

In Situ Diffuse Reflectance Spectroelectrochemistry Of Cathode Materials In Lithium-Ion Batteries, Lu-Lu Chen, Hao-Ran Li, Wei-Yi Liu, Wei Wang

Journal of Electrochemistry

Developing in situ spectroelectrochemistry methods, which can provide detailed information about species transformation during electrochemical reactions, is very important for studying electrode reaction mechanisms and improving battery performance. Studying real-time changes in the surface of electrode materials during normal operation can be an effective way to assess and optimize the practical performance of electrode materials, thus, in situ and in operando characterization techniques are particularly important. However, batteries are hard to be studied by in situ characterization measurements due to their hermetically sealed shells, and there is still much room for battery characterizations. In this work, a specially designed battery …

Molybdenum Disulfide And Carbon Nanotubes Composite Electrode For Electrochemical Conversion Of Salinity Gradient Energy, Jia-Jun Li, Wei-Bin Zhang, Xin-Yu Liu, Jing-Lei Yang, Yi Yin, Ze-Qin Yang, Xue-Jing Ma

Journal of Electrochemistry

The ocean accounts for 97% of the total water resources on earth, covering over 70% of the map's surface area. With the continuous consumption of non-renewable energy sources such as fossil fuels and the rapid development of renewable energy, humans are increasingly paying attention to the utilization of ocean resources. Ocean energy includes tidal energy, wave energy, temperature difference energy, and salinity gradient energy. Salinity gradient energy is the energy generated by the interaction of seawater and fresh water, which is the ocean energy existing in the form of chemical energy. This energy is mostly generated in estuaries. The osmotic …

Photodegradation Of Microplastics Through Nanomaterials: Insights Into Photocatalysts Modification And Detailed Mechanisms, Yiting Xiao, Yang Tian, Wenbo Xu, Jun Zhu

Biological and Agricultural Engineering Faculty Publications and Presentations

Microplastics (MPs) pose a profound environmental challenge, impacting ecosystems and human health through mechanisms such as bioaccumulation and ecosystem contamination. While traditional water treatment methods can partially remove microplastics, their limitations highlight the need for innovative green approaches like photodegradation to ensure more effective and sustainable removal. This review explores the potential of nanomaterial-enhanced photocatalysts in addressing this issue. Utilizing their unique properties like large surface area and tunable bandgap, nanomaterials significantly improve degradation efficiency. Different strategies for photocatalyst modification to improve photocatalytic performance are thoroughly summarized, with a particular emphasis on element doping and heterojunction construction. Furthermore, this review …

Modeling Charging Current Dynamics At Microelectrodes And Their Interfaces With Electrolyte And Insulators With A Focus On Microfabricated Gold Microband Electrodes On An Su-8 Substrate, Miguel Angel Abrego Tello, Mahsa Lotfi Marchoubeh, Ingrid Fritsch

Chemistry & Biochemistry Faculty Publications and Presentations

The suitability of electrochemical methods for quantitative measurements at microdevices is influenced by the relatively large electrode-insulator interface-to-electrode area ratio, greatly impacting charging dynamics due to interactions among electrolyte, conductor material, and insulator layers. The resulting charging current can overwhelm the faradaic current from redox chemistry. The device studied here features a 70 μm × 100 μm electroactive window, hosts gold coplanar microband electrodes, and is insulated by SU-8, which serves as both overlayer and substrate. The overlayer defines the electroactive length and isolates the leads of the electrodes from the sample solution. Cyclic voltammetry in 0.10 M …

In Situ And 2d And 3d In Silico Redox Cycling Studies For Design Optimization Of Coplanar Arrays Of Microband Electrodes In A 70 Μm × 100 Μm Electroactive Footprint, Miguel Angel Abrego Tello, Mahsa Lotfi Marchoubeh, Ingrid Fritsch

Chemistry & Biochemistry Faculty Publications and Presentations

Optimization of redox-cycling currents was performed by adjusting the height (sidewalls, h), width (w), and length (l) of band electrodes and their spacing (w_gap) in coplanar arrays restricted to a small-electroactive window of 70 × 100 μm. These arrays can function in μL-volumes for chemical analysis (e.g., in-vivo dopamine detection using probes). Experiments were conducted with an array of five electrodes (NE = 5), w = 4.3 μm, w_gap = 3.7 μm, h = 0.150 μm, and l = 99.2 μm. Reasons for …

Predicting Rheology Of Uv-Curable Nanoparticle Ink Components And Compositions For Inkjet Additive Manufacturing, Cameron D. Lutz

Master's Theses

Inkjet additive manufacturing is the next step toward ubiquitous manufacturing by enabling multi-material printing that can exhibit various mechanical, electronic, and thermal properties. These characteristics are realized in the careful formulation of the inks and their functional materials, but there are many constraints that need to be satisfied to allow optimal jetting performance and build quality when used in an inkjet 3-D printer. Previous research has addressed the desirable rheology characteristics to enable stable drop formation and how the metallic nanoparticles affect the viscosity of inks. The contending goals of increasing nanoparticle-loading to improve material deposition rates while trying to …

Effects Of Ti Addition On The Characteristics Of Al-10zn-6mg-2si/Zro2 Composites Produced By Squeeze Casting, Qesha Diva Prameshvara, Pipin Indah Lestari, Bondan Tiara Sofyan

Journal of Materials Exploration and Findings

Metal matrix composite (MMC) with 7xxx aluminum matrix is potential for ballistic applications due to the combination of strength, toughness, and light weight. Previous study successfully produced aluminum-based composites with SiC particles which were able to stop type III bullet, however cracks remained on back of the plate. Therefore, in this research, SiC was replaced by zirconia (ZrO₂) due to its high fracture toughness. Ti-B grain refiner was added to further improve toughness through grain boundary strengthening mechanism. This research developed 5 vol.% ZrO₂ strengthened Al-10Zn-6Mg-2Si composite with addition of Al-5Ti-1B grain refiner produced through squeeze casting …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Review Of Cyclic Voltammetry Measurements For Uranium In Flinak Molten Salt, Jackson Ivory

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

The electrochemical behavior of uranium FLiNaK molten salts is explored, focusing on cyclic voltammetry (CV) as a powerful tool for redox characterization and diffusion studies. Through a comprehensive review of recent research, the study highlights the significance of CV in understanding electrode kinetics, material compatibility, and process optimization in molten salt environments. The findings underscore the potential of FLiNaK molten salt reactors in advancing nuclear energy technologies, fuel processing, and waste management strategies. Collaborative interdisciplinary efforts are emphasized to address challenges and accelerate innovation in electrochemical methods for nuclear applications.

An Overview Of How To Measure The Kinetic Properties Of An Anode Material For The Chlorine Evolution Reaction, Cameron Vann

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

The process of generating chlorine gas using electrolysis in aqueous systems is well established. However, a new process requires chlorine to be generated at high temperatures using molten salt. This harsh environment requires a new study of anode materials for the chlorine evolution reaction. Anode materials can be compared by their kinetic parameters, the transfer coefficient α and the exchange current i0. The basic theory of these properties as they relate to the chlorine evolution reaction has been detailed and an analysis method for finding these effective parameters has been shown and demonstrated.

Investigating The Impact Of Secondary Activation Time On The Adsorption Properties Of Activated Biochar For Arsenic Removal From Wastewater, Achyuth Bharadwaj Rayarao

Graduate Theses and Dissertations (2019 - present)

Biochar, a naturally occurring and renewable carbon material, becomes porous through activation. Activated biochar is an ideal candidate for use as an adsorbent. The objective of this study is to investigate whether activated biochar derived from Colorado soft pine serves as a better adsorbent and demonstrates enhanced adsorption capabilities after undergoing secondary physical activation at various activation times. The effect of secondary action time on physical adsorption properties drawn from the analysis of isotherm plots, surface areas and pore size patterns were examined by using a physisorption analyzer. Chemical structures were identified using both ultimate and proximate analyses, while porosity …

Boron-Doped Diamond As A Resilient Electrode Material In Molten Salts, Hannah Katherine Patenaude

UNLV Theses, Dissertations, Professional Papers, and Capstones

Molten salt chemistry has a range of applications within nuclear technology, including for the Molten Salt Reactors (MSRs) and pyroprocessing to recover valuable actinides for energy and national security needs. However, the high-temperature, corrosive nature of molten salts makes them particularly challenging to deploy on an industrial scale and study in benchtop measurements. Material accountability and corrosion monitoring of MSR fuels are essential components to the successful deployment of MSRs, and electroanalytical techniques like cyclic voltammetry (CV) and spectroelectrochemistry (SEC) can provide a wealth of information to describe salt systems in situ. To perform such measurements, it is imperative to …

Revealing The Three-Dimensional Arrangement Of Polar Topology In Nanoparticles, Chaewa Jeong, Juhyeok Lee, Hyesung Jo, Jaewhan Oh, Hionsuck Baik, Kyoung-June Go, Junwoo Son, Si-Young Choi, Sergey Prosandeev, Laurent Bellaiche, Yongsoo Yang

Physics Faculty Publications and Presentations

In the early 2000s, low dimensional ferroelectric systems were predicted to have topologically nontrivial polar structures, such as vortices or skyrmions, depending on mechanical or electrical boundary conditions. A few variants of these structures have been experimentally observed in thin film model systems, where they are engineered by balancing electrostatic charge and elastic distortion energies. However, the measurement and classification of topological textures for general ferroelectric nanostructures have remained elusive, as it requires mapping the local polarization at the atomic scale in three dimensions. Here we unveil topological polar structures in ferroelectric BaTiO₃ nanoparticles via atomic electron tomography, which …

Engineering Multifunctional Silicon Nanostructures From Biorenewable Cellulose Nanocrystals, Nancy Chen

All Dissertations

The imperative search for alternative materials to address the pressing demand for advance energy storage is underscored by the escalating environmental predicaments. Lithium-ion batteries (LIBs) with graphite anodes have become the benchmark in energy storage; however, they are approaching a saturation point in terms of energy density. Silicon emerges as a promising contender to supplant graphite, owing to its profuse availability, cost-effectiveness, and impressive specific capacity of 4200 mAh g^-1. By integrating silicon anodes, LIBs stand to undergo a radical transformation, markedly diminishing in weight and size, thus heralding a novel wave of compact, lightweight energy storage systems. …

Surface Treatments' Effects On The Capacitor's Dielectric Performance Under Electro-Thermal Stresses, Haider. M. Umran, Feipeng Wang

Karbala International Journal of Modern Science

Biaxial-oriented polypropylene (BOPP) films are characterized by unfavorable aging behavior because of their poor susceptibility to high temperatures, humidity, and high electric fields. This makes them unqualified to withstand harsh operating conditions, such as in capacitor applications. This study investigates the impact of annealing BOPP samples at 100 °C for five hours after fluorination at different times (15, 30, and 60 minutes) on their electrical and mechanical performance under electro-thermal stresses. Scanning electron microscope (SEM) images confirm that there is an increase in surface roughness and the formation of a dense layer of fluorine-containing groups monotonically with fluorination time. So, …

Seeding Effects Of Submicron Caal-No3 Ldh Particles On The Hydration And Properties Of Portland Cement And Sulfoaluminate Cement Pastes, Sukanta K. Mondal, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Layered double hydroxide (LDH) is reported to improve the durability of concretes, primarily due to its ability to exchange anionic species, including chloride, which is implicated in corrosion-driven durability issues. However, there is no comprehensive study investigating the effect of LDH on the properties of different cement systems at both early and mature ages. in this study, the early age and mature age properties of Portland cement (OPC) and calcium sulfoaluminate (CSA) cement pastes seeded with submicron-sized calcium aluminum-NO3 LDH (CaAl-NO3 LDH) were investigated. the effects of the 1–5%mass dosage of LDH on the hydration of both cement systems were …

Thermal Frontal Polymerization – Applications In Coatings And Composites, Maria Martinez

LSU Doctoral Dissertations

Thermal frontal polymerization has long been used as a method to cure composites and coatings. However, this is the first time these applications have been used without the use of a catalyst, for the case of composites and coatings.

Chapter 2 discusses how to optimize cure-on-demand, thin layer coatings, using frontal polymerization. Previously, for the use of curing thin layer coating using thermal FP, it was known to just make the formulation viscous enough, as this would prevent premature quenching caused by heat loss. It was discovered that for a given layer thickness, a minimum viscosity and initiator concentration were …

Shorting At Long Duration: Impact Of Extended Discharge Capacity On Battery Solid Electrolytes, Ryan C. Hill, Amanda S. Peretti, Leo J. Small, Erik D. Spoerke, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

Long-duration energy storage (LDES) is critical to a stable, resilient, and decarbonized electric grid. While batteries are emerging as important LDES devices, extended, high-power discharges necessary for cost-competitive LDES present new materials challenges. Focusing on a new generation of low-temperature molten sodium batteries, we explore here unique phenomena related to long-duration discharge through a well-known solid electrolyte, NaSICON. Specifically, molten sodium symmetric cells at 110 ° C were cycled at 0.1 A cm−2 for 1–23 h discharges. Longer discharges led to unstable overpotentials, reduced resistances, and decreased electrolyte strength, caused by massive sodium penetration not observed in shorter duration discharges. …

Advancements In Characterization Of Ancient Potteries From Southeast Asia: A Review Of Analytical Techniques, Chitnarong Sirisathitkul

Makara Journal of Science

Ancient potteries offer valuable information regarding technological advancements, life dynamics, cultural diversity, and trade routes in the past. Earthenware, stoneware, and porcelain from Southeast Asia have been characterized using several analytical techniques, as reviewed in this article. Fluorescent and diffracted X-rays give rise to elemental and phase compositions, respectively. Examination of molecular bonds requires vibrational spectroscopy, which is useful for the identification of organic materials in ancient potteries. With the advent of portable X-ray fluorescence and Raman spectrometry, on-site analysis of archeological ceramics is now possible. For in-depth analysis, synchrotron light sources can provide new insights into artifacts through X-ray …

Recent Advances In Solar Photo(Electro)Catalytic Nitrogen Fixation, Jun-Bo Ma, Sheng Lin, Zhiqun Lin, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Ammonia (NH₃) is an essential chemical in modern society. It is currently produced in industry by the Haber-Bosch process using H₂ and N₂ as reactants in the presence of iron-based catalysts at high-temperature (400–600 ^oC) and extremely highpressure (20–40 MPa) conditions. However, its efficiency is limited to 10% to 15%. At the same time, a large amount of energy is consumed, and CO₂ emission is inevitably. The development of a sustainable, clean, and environmentally friendly energy system represents a key strategy to address energy crisis and environmental pollution, ultimately aiming to achieve carbon neutrality. …