Materials Science and Engineering Commons^™

Preliminary Examination Of The Aluminum Corner Of The Ternary System Aluminum-Silver-Indium (A1-Ag-In), Jerome J. Blake

Bachelors Theses and Reports, 1928 - 1970

In this paper the author attempts to lay the groundwork for future work on the Al-Ag-In system.

Increased Corrosion Of A 304 Stainless Steel Upon Bending, William C. Tiddy

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Identification Of Nonmetallic Inclusions In Armco Ingot Iron With Polarized Light, Frank E. Panisko

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

The Hydrometallurgy Of Uranium, John E. Cesarani

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

A Preliminary Study Of The Dielectric Properties Of Bismuth Ferrate Ceramics., John Joseph Schwaller

Masters Theses

"In this investigation some of the results of Fedulov¹⁸ for a composition of 30 percent lead titanate - 70 percent bismuth ferrate were verified. The system of lead zirconatebismuth ferrate was studied with sintering data determined for the series. By X-ray and microscopic analysis the system was determined to be not a solid solution. The dielectric measurements show a linear relation between the dielectric constant and the percent lead zirconate from 100 percent BiFeo₃ to 10 percent BiFeo₃ - 90 percent PbZro₃"--Abstract, p. ii

Preliminary Investigation Of Acid Treatment For The Stabilization Of Doloma, Deward Pan

Masters Theses

"The work presented in this thesis is the result of an investigation to develop an economical and successful means for producing a stable, hydration resistant compound on the surface of doloma particles by an acid treatment, which does not significantly alter the refractoriness of the material. Granite, a commercial doloma, from Valley Dolomite Corporation, was treated with different concentrations of inorganic acid-water solutions and organic acid-alcohol solutions for varying time at atmospheric pressure and temperature. The treated doloma was examined by (l) X-ray diffraction and (2) the hydration test.

It was found that the organic acid acted as a coating …

Influence Of Porosity On The Fracture Stresses Of Electrical Porcelain., Edward Anton Snajdr

Masters Theses

"Spherical pores were induced in a typical quartz electrical porcelain body. Three levels of pore size and four levels of concentration were studied. Large strength sample sizes were employed using a three-point loading and diametral loading method. Data for induced quartz particles is also included"--Abstract, p.ii

Crystal Habit Modification Of Sodium Chlorate, Michael R. Keegan

Bachelors Theses and Reports, 1928 - 1970

All single crystals have a particular habit or morphology. The crystal habit refers to the relative degree of development of crystallographic planes into surfaces which make up the external appearance of the single crystal.

In this paper, NaClO3 is used as a parent crystal. Its simple cubic habit is modified to tetrahedral by the use of impurities of SO4=, S2O3=, Cr2O7=, and NO3-. The degree of habit change is studied as a function of impurity concentration and temperature. The problem and phenomena are explained in terms of surface chemistry and thermodynamics.

Physico-Chemical Principles Of Sixteenth Century Metallurgy, Robert E. Johnson

Bachelors Theses and Reports, 1928 - 1970

Following a review of sixteenth century metallurgical literature and a discussion of Gibbs free energy, this thesis discusses thermodynamic considerations of galena (PbS) reduction by iron from a lead assay of this period. The importance of fluxes in this assay is emphasized. The discussion covers both equilibrium and non-equilibrium conditions at 1100 degrees Celsius. Possible substitutes for iron are also covered.

Information from twenty-one small controlled lead assays is correlated with the thermodynamic discussion to determine the purpose of each constituent in the assay.

The Beneficiation Of Titaniferous-Magnetite Sands, Ronald Lloyd Nordwick

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation of beneficiation methods is to develop and study possible economic methods for recovering an iron-titanium concentrate of sufficient purity to meet metallurgical requirements for subsequent direct reduction to pig iron and a high titanium slag.

Stress-Corrosion Cracking Of Brass, Paul A. Fossey

Bachelors Theses and Reports, 1928 - 1970

the mechanism of stress-corrosion cracking of brass has been sought for many years. Investigators have proposed many mechanisms, but each of these mechanisms has always had several drawbacks. This paper presents an account of experimental work done in the laboratory on this subject and compares it to the work of previous investigations. It evaluates the mechanisms presented by investigators and shows the failures of these mechanisms. A theory of Nitrogen Embrittlement is presented and an evaluation of this theory with experimental work follows.

Experimental Arc Furnace Smelting Of Titaniferous Iron Sands From The Northern Oregon Coast, Allan P. Herring

Bachelors Theses and Reports, 1928 - 1970

This investigation is an attempt to experimentally smelt titaniferous iron sands from the Northern Oregon Coast in a laboratory arc furnace.

The Effect Of Ph Upon Chelation Reactions In Montmorillonite Clays, Joseph Michael Keane

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to investigate several chelation reactions and determine the effect of variable pH upon these reactions.

An Investigation Of The Sintering Of Iron-Wire Compacts, George L. Vivian

Bachelors Theses and Reports, 1928 - 1970

A study of the sintering of iron has been made by observing the rate of bonding of iron wires wound on iron spools. The specimens were sintered at a constant temperature of 850c in vacuum furnaces capable of producing pressures of 10-5 to 10-4 mm of mercury, and the growth of the bond between wires was observed as a function of time.

It has been concluded that the volume-diffusion mechanism is strongly operating in the sintering of iron at 850c, but in an evacuated system, the evaporation-condensation mechanism also contributes to the sintering process.

Statistical Analysis Of Fracture Stresses Of Triaxial Porcelain Bodies, Robert E. Moore

Doctoral Dissertations

"Triaxial porcelain bodies containing various forms of silica, quartz, cristobalite and fused silica, were strength tested in bending. Significance tests were employed to discern real differences in the strength sample statistics caused by the various forms of silica. Firings were performed at three temperature levels. The differences in strength sample statistics were correlated to the microstructures of these silica porcelains.

A triaxial alumina porcelain body was employed as a model brittle solid for a study of the effect of flaw density on mean fracture stress. The flaws were introduced in the form of large diameter (d̄ = 115 microns) rounded …

Preliminary Investigation Of The Effects Of Seeding Fusion Cast Refractories, Thomas Spencer Montgomery

Masters Theses

"The crystallization process in a zirconia-alumina- silica melt of high viscosity was studied, A system was used of the same composition found in commercial electrocast glass tank refractories. Artificial nucleation was tried in an attempt to control the process of crystallization; the method involved the addition of suitable "seeding" material.

It was found that introduction of nucleation agents consisting of the major component oxides of the system had noted effect upon the course of crystallization. Preferred orientation normally found in unseeded electrocast refractories was diminished with the addition of zirconia grains and amplified with particles of tabular alumina.

Results obtained …

A Preliminary Study Of The Effect Of Heat Treatment On The Strength And Microstructure Of A Glass-Ceramic Material, P. D. Ownby

Masters Theses

"The strength and microstructure of a glass-ceramic material of the composition 53 percent SiO₂, 19 percent Al₂O₃, 15 percent MgO, and 13 percent Li₂O were studied. Cylindrical specimens of glass were formed and heat-treated to six different temperature levels for various time periods. The method of strength testing used was a diametral compression loading technique. It was found that the strength of this material increased initially with heat-treatment but then decreased. The strength characteristics of the completely crystallized glass ceramic material were found to be dependent on the initial nucleation period. Some factors which influenced anomalous crystal growth are described. …

A Vacuum Induction Furnace For Pyrometric Cone Equivalent Determinations, Robert E. Farris

Masters Theses

"Various furnaces which are commonly used for P.C.E. determinations were compared from a literature review. The inadequacies of these furnaces were noted and a furnace was designed, constructed, and evaluated in an effort to minimize or eliminate some of the indicated problems. For this furnace heat is developed in opposed cones (susceptors), which are fabricated from 0.005” molybdenum sheet, by induced (induction) currents from a 10 KW vacuum tube generator. The furnace components are enveloped by a pyrex cylinder in which a vacuum (approximately 1 to 5 micron pressure absolute) is maintained during operation"--Abstract, page ii.

The Identification Of Montana Clays By X-Ray Analysis, David Stephen Malyevac

Bachelors Theses and Reports, 1928 - 1970

The purpose of this study is to identify the various Montana clay minerals by means of X-ray diffraction. The ultimate aim of this investigation is to identify the different clay mixtures through an analysis of their respective diffraction patterns, and diffraction patterns obtained after various chemical and thermal treatments.

Some Properties Of Chrome-Magnesite Mixtures And Calcium Aluminate Cement-Magnesite Mixtures, Edward Charles Duderstadt

Masters Theses

"The knowledge of the physical and chemical properties of refractories is of great importance in determining their usefulness and application. The thermal expansion of refractories is of particular importance in that it affects the thermal stability of the product. A high coefficient of thermal expansion leads to greater spalling and destruction of the bricks in use. It is, therefore, desirable to develop compositions having low coefficients of thermal expansion. This investigation was undertaken (1) to determine some of the properties of chromite-magnesite refractory mixtures in an attempt to determine the optimum composition of these mixtures, the specific properties including thermal …

Phase Relationships In The Quaternary System Lime-Titania-Zirconia-Silica, Robert Martin Gruver

Doctoral Dissertations

"The phase compatibility relationships for the quaternary system lime-titania-zirconia-silica have been determined by a solid-phase-reaction technique.

Preliminary division of the system into Alkemade tetrahedra was based on the phases found in samples by X-ray diffraction analysis. These samples covered the entire volume of the tetrahedron in a systematic fashion. When the quaternary system had been divided into regions or compatible phases, an analytical method was used to calculate the phase composition of each sample. The relative amounts of each phase in a sample determined by X-ray analysis were compared with the calculated quantities, and agreement between the two methods verified …

Nanbo₃ - Batio₃ - Basno₃ Ceramic Dielectrics, William Dean Mckee

Doctoral Dissertations

"A. The Problem.

The purpose of this investigation was to form by ceramic processes a number of compositions in the ternary system NaNbO₃ - BaSnO₃ - BaTiO₃, to determine certain dielectric properties of these, to study them by means or x-ray diffraction, and to determine the extent or correlation possible between the compositional variation of dielectric properties and the x-ray results.

Compositions investigated contained 50 mole percent or less BaSnO₃. Materials and methods of forming were chosen with the intent that the final bodies should be pure oxide compositions as represented in the ternary …

The Design And Construction Of An Electrolytic Cell For Aluminum Reduction, Thomas H. Melrose

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation was to design and construct a laboratory size electrolytic cell in which to reduce alumina, using the same basic materials that are used in a commercial size cell. The cell was designed to have a capacity of approxi­mately 100 grams of metallic aluminum produced every 8 hours. The cell was constructed so it could be operated continuously.

Investigation Of Inclusions In Armco Ingot Iron, Edwin J. Duncan

Bachelors Theses and Reports, 1928 - 1970

Various chemical and electrolytic separation methods were investigated in an attempt to separate the in­clusions in Armco ingot iron. Residues obtained were X-rayed for identification purposes. The microstruc­tures of this iron were studied with the object of de­termining the relative sizes, locations, and possible compositions of the inclusions.

Effect Of Recovery On The Recrystallized Grain-Size Of High Purity Aluminum, Rodney L. Helterline

Bachelors Theses and Reports, 1928 - 1970

When a cold-worked metal is annealed, it’s physical properties hange as a result of a new grain structure. The annealing treatment is divided into three stages according to the changes that occur in the distorted metal: (1) recovery, (2) recrystallization, and (3) grain growth.

Polarography Of Indium, John Jackson

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to study the various aspects of the polarography of indium. The eventual goal would be to develop a method of analyzing indium in unknowns. The investigation is approached by studying the indium ions in various electrolytes and in various concentrations.

Geology Of The Ragged Point Oil Field Musselshell County, Montana, David M. Amos

Bachelors Theses and Reports, 1928 - 1970

The Ragged Point oil field is located in Northwest Musselshell County, in the Lake Basin field of central Mon­tana, and on the western border of the Great Plains region. The surface topography is that of a plain marked by erosion and moderate folding. The stratigraphy of central Montana shows periodic marine invasions from the Cordilleran trough, with normal marine limestones interbedded with sandstone sand shales. These sediments are over 12,000 feet thick, with the Creta­ceous Eagle and Colorado formations exposed at the surface on the Ragged Point anticline. Undifferentiated Cambrian lime­stones and shales are the oldest rocks encountered in drilling.

An Investigation Of The Characteristics Of High Alumina Refractory Castables, Gajendra Nath Mohanty

Doctoral Dissertations

"Refractory castables or concretes, a comparatively new member of the refractories family, are an admixture of highly aluminous cements and graded refractory aggregates, blended in predetermined proportions very much like structural concrete. The refractory aggregates must contain a large amount of fines contrary to the requirements of ordinary concrete. Unlike the Portland cements, which are mainly combinations of calcium silicates, the highly aluminous cements are predominantly calcium aluminates. They are comparatively of a refractory natures, having the hydraulic setting property combined also with high early strength. The discovery of the fact that these refractory concretes could be cast, in situ, …

A Fundamental Study Of Clay Drying Using Ware Of Large Cross Section, Robert F. Grady Iii

Masters Theses

"The drying of clay has been studied extensively in the past by many investigators, some of whom attempted to relate this information to the structure of clay and thereby develop a more vivid picture, while others studied the mechanism of drying in its own right in order to present a useable theory that would allow improvements in the drying operation.

At present the literature is unable to present a theory of the mechanism of drying that is sufficiently general to cover the observed aspects of clay drying. Many and varied mechanisms are presented, but correlation is seldom completely evident between …

Testing Of Missouri Shales For Light Weight Aggregate Production, Jerry D. Plunkett

Masters Theses

"The original objective of this investigation was to determine by testing those clays, shales, and loesses occuring in Missouri in large deposits (over 15 feet in thickness with little overburden), which would be suitable for the production of light weight aggregate. The second objective was to investigate the mechanism of bloating as related to the physical and chemical properties of the above materials, and by using these relationships cause clays which do not naturally bloat, to bloat using some addition. The use of additives would permit the economical use of material closer to the market in many instances.

After the …