Materials Science and Engineering Commons^™

X-Ray Powder Data And Unit Cell Parameters Of Mgbr2.6h2o, Charles A. Sorrell, Roy R. Ramey

Materials Science and Engineering Faculty Research & Creative Works

Detailed X-ray powder data for MgBr2·6H2O were obtained by diffractometry by use of CuKα radiation at 22°C. The data were indexed on a bimolecular monoclinic unit cell, space group C2/m, with a = 10.290 ± 0.001 Å; b = 7.334 ± 0.001 Å; C = 6.211 ± 0.001 Å; β = 93° 25′ ± 10′. Calculated density was 2.074 g/cm3, compared with a measured density of 2.07 ± 0.01 g/cm3. © 1974, American Chemical Society. All rights reserved.

Knudsen Effusion Study Of The Vaporization Of Cdo(S), R. Tom Coyle, Gordon Lewis

Materials Science and Engineering Faculty Research & Creative Works

Knudsen effusion studies were conducted on CdO(s) in fused‐SiO2 Knudsen cells from 889 to 1110 K. The orifice size was varied; the largest cell orifice yielded a calculated pressure significantly lower than could be accounted for by experimental error. Average‐slope‐ and average‐free‐energy‐function‐based values of ΔHc298 were 86.9 ± 1.1 and 88.8 ± 0.5 kcal/mol, respectively. The data from the present work were combined with those of previous investigators using a method discussed by McCreary and Thorn; a ΔHc298 of 88.2 ± 0.2 kcal/mol was obtained. Using this combined value for ΔHc298 and ΔSc298= 51.40 ± 0.1 eu (obtained from the …

Phase Equilibria And Transformations In Potassium Sulfate, Chromate, Molybdate, And Tungstate, Roy Richard Ramey

Doctoral Dissertations

"Thermal expansion and transformations of K₂SO₄, K₂CrO₄, K₂MoO₄, and K₂WO₄ were studied by high temperature diffractometry, differential thermal analysis, and dilatometry. K₂SO₄ and K₂CrO₄ transform from an orthorhombic to a hexagonal structure at 580°C and 670°C respectively, with initiation of the transformation probably related to increased amplitude of S-O tetrahedral vibrations. K₂MoO₄ and K₂WO₄ transform from a monoclinic to an orthorhombic structure at 300° and 370°C respectively. A minor K₂MoO_{4 …}

Thermal Decomposition Of Boron Triiodide On Molybdenum Field Emitter Surfaces, Richard E. Moore, P. Darrell Ownby

Materials Science and Engineering Faculty Research & Creative Works

Boron has been adsorbed onto molybdenum field emitter surfaces by the thermal decomposition of boron triiodide at corrected partial pressures of 1.4 x 10-9 Torr to 4.5 x 10-9 Torr. Based on field emission work function data and an analytical work function versus adsorbate-coverage relationship, a quantitative measure of the monolayer coverage of boron on molybdenum has been determined; this value is 6.3 x 1014 atoms/cm2/monolayer. A parameter, β, is defined which is a measure of the effective yield of adsorbed boron on molyb-denum from BI3. β is formulated in terms of the free energy of dissociation of the BI3 …

X-Ray Powder Data And Unit Cell Parameters Of Mgcl2.6h2o, Charles A. Sorrell, Roy R. Ramey

Materials Science and Engineering Faculty Research & Creative Works

Detailed X-ray powder data for MgCl2·6H2O were obtained by diffractometry by use of CuKα radiation at 22°C. The data were indexed on a bimolecular monoclinic unit cell, space group C2/m, with a = 9.858 ± 0.001 Å; b = 7.107 ± 0.001 Å; c = 6.069 ± 0.001 Å; ß = 93° 47′ ± 10′. Calculated density was 1.591 g/cm3, compared with a measured density of 1.593 ± 0.003 g/cm3. © 1974, American Chemical Society. All rights reserved.

A Mass Spectrometric Study Of Positive Ions Produced In An Experimental Diode, L. A. Addington, Gordon Lewis

Materials Science and Engineering Faculty Research & Creative Works

A simple diode ion source has been developed for direct observation in a mass spectrometer of the positive ions created in an operating diode. The ionic species accelerated toward the cathode were identified. The shape of the peak displayed in the spectrum is related to the region of the diode in which the ions were formed. Variation of experimental parameters, including the composition of the background gases, indicated that the characteristic shapes of the peaks can be related to space charge in the diode. This is complicated by the tendency of some of the species to fragment and further work …

Effect Of Dissolved Water On Physical Properties Of Silver Borate Glasses, E Richard Reynolds

Masters Theses

"The effect of dissolved water on borate glasses containing 4-20 mol % Ag₂O was investigated. Water was dissolved in the glasses by bubbling with a carrier gas (oxygen) containing different partial pressures of water vapor. A minimum in water solubility was found at 11 mol % Ag₂O. Water contents in excess of 0.5 mol % H₂O did not have a great effect on the transition temperature or the dilatometric softening point. Below 15 mol % Ag₂O, the water content had no effect on the thermal expansion coefficients. Beyond 15 mol % Ag …

Determination Of Oxygen Chemical Diffusion Coefficients In Single Crystal Strontium Titanate By Capacitance Manometry, Douglas Bugh Schwarz

Masters Theses

"The use of the tensi-volumetric apparatus to study the non-stoichiometric behavior of strontium titanate was discussed. Oxidation kinetics of reduced single crystal strontium titanate were measured with an ultrasensitive capacitance manometer as the sample absorbed oxygen in response to a changing oxygen activity.

The oxidation kinetics were found to fit a solution to Fick's second law for rectangularly shaped samples....

The procedure selected for measurement of the oxidation kinetics, and the method of obtaining diffusion coefficients from the oxidation data was discussed along with potential sources of error of the system"--Abstract, page ii.

Synthesis Of Fused Silica By Flame Hydrolysis, James Edward Rourke

Masters Theses

"Apparatus to synthesize and dope high purity, optical quality fused silica by flame hydrolysis was constructed. Fused silica samples containing 0, <35, 35 and 90 ppm niobium were synthesized and characterized by the following properties: purity, refractive index, radiation damage resistance, and transmission spectra. The properties of the undoped sample were shown to be comparable to those of available commercial fused silica. Deviations in the properties of the doped samples from those of the undoped samples were explained in terms of the niobium content"--Abstract, page ii.

Solid Transformations And Premelting Phenomena In Fluorite Structures And The System Srcl₂Bacl₂, Damri Sukhotanang

Doctoral Dissertations

"Thermal expansion and phase transformations in CaF₂, BaF₂, SrCl₂, and BaCl₂ were studied by high temperature x-ray diffractometry, differential thermal analysis, and thermodilatometric analysis. Thermal expansion characteristics of CaF₂, BaF₂ and SrCl₂ are very similar. The structures expand normally at lower temperatures and depart substantially from linearity at higher temperatures, because of formation of defects and disordering of anions. At high temperatures CaF₂ and BaF₂ react with water vapor, even at low humidities, forming oxides and emitting HF, leading to difficulty in observation of phase transformations. SrCl …

Polynary Silicon Arsenic Chalcogenide Glasses With High Softening Temperatures, H. E. Anthonis, N. J. Kreidl, W. H. Ratzenboeck

Materials Science and Engineering Faculty Research & Creative Works

The introduction of Ag in SiAsTe glasses permits the incorporation of Se, otherwise volatile and/or degradable as a constituent in Si-containing chalcogenide glasses. SiAsAgTeSe glasses exhibit much higher softening ranges and glass transition temperatures than encountered in known chalgogenide systems. A glass Si35As15Ag10Te20Se20 had the viscosity log ν = 13 at about 500°C, as compared to 370°C for the base glass Si35As25Te40, the viscosity of log ν = 9.8 at about 560°C, as compared to 442°C for the base glass. Phase separation occurs in the system SiAsAgTeSe and becomes manifest in two glass transitions indicated by changes in the slopes …

Oxidation Of Tetragonal Pbo In Air, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

Isothermal oxidation of tetragonal PbO in air produced multiphase assemblages with apparent equilibrium compositions which varied linearly with temperature from PbO1.548 at 286°C to PbO1.333 at 351°C. Oxidation at each temperature was relatively rapid to PbO1.40 and very slow from PbO1.40 to apparent equilibrium values. Pseudocubic PbO1+x, with compositions between PbO1.41 and PbO1.57, was indexed on a cubic unit cell at the lower O/Pb ratios and on a tetragonal unit cell at the higher ratios. Linear changes in lattice parameters and deviation from cubic symmetry accompanied reversible oxidation and reduction of the phase. Pseudocubic PbO1+x was reduced irreversibly to Pb3O4 …

Formation And Densification Of Cadmium Manganese Ferrite, B. W. Jong, P. D. Ownby

Materials Science and Engineering Faculty Research & Creative Works

Formation of Ni-ferrite, Mn-ferrite, NiZn-ferrite, Zn-ferrite and Mg-ferrite have been investigated using X-ray diffraction analysis. Jander's diffusion equation described the data from these investigations over a portion of the temperature ranges studied. However, the reaction mechanisms and sequences involved in the formation of mixed ferrites have not been well defined in the literature. The purposes of this investigation were: ( 1) To further the understanding of the formation of CdMnferrite by studying first the kinetics of the formation of Cd-ferrite and Cd-manganite, which provides a basis for understanding the details of the mixed CdMn-ferrite reaction and to obtain the optimum …

Oxidation State Control Of Volatile Species In Sintering, P. D. Ownby

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Characterization Of A Mexican Halloysitic Clay And Behavior In Dry Pressing, Jesus L. Derat

Masters Theses

"A Mexican clay, intended to be used as refractory raw material, was identified. Problems encountered in the characterization of halloysitic clays are discussed and emphasis is made on the use of the electron microscope (scanning or transmission type) as a definite evidence of the existence of halloysite due to its unique morphology within the kaolinite group of clay minerals.

Beneficiation of this particular clay was carried out on a small scale hydrocyclone equipment and the results are discussed.

In an attempt to increase the green density in dry pressing of this halloysitic clay, mixtures with grog were prepared using different …

Sintering And Microstructure Control Of A Ferrimagnetic Mn-Zn Ferrite Spinel, Joel Keith Michel

Masters Theses

"The effect of minor additions of CaO dopant to a manganese zinc ferrite – Zn_.25Mn_.75 Fe_2.17 O_4.0 - on its grain growth and densification kinetics in air at 1250°C., 1300°C., and 1350°C. was studied. Grain growth was controlled over a range of dopant levels. At a sintering temperature of 1350°C. and time of six hours a ferrite with the smallest dopant addition was sintered to the highest density - 98% of theoretical. Under the same sintering conditions ferrites with higher dopant levels also sintered with normal growth but sintered to lower densities.

Due to discontinuous …

The Effect Of Porosity On Strength Degradation In Thermally Shocked Alumina, Russell David Smith

Masters Theses

"Strength degradation and crack propagation in Al₂O₃ are shown to depend on the initial strength and porosity of the material. Specimens were fabricated containing between 0 and 5% induced cylindrical, two dimensional, and spherical porosity. The strengths of the various porosity samples decreased discontinuously at a critical quenching temperature. No difference was observed in the critical temperature for the various aluminas; initial strength decrease occurred between 165°C and 175°C temperature differential. The strength retained after thermal shock decreased with increasing initial strength. The degree of damage sustained upon shocking was also characterized by crack density and crack …

Initial Surface Reactions And Nucleation Kinetics Of Boron On Atomically Clean Molybdenum Substrates, Richard Eugene Moore

Doctoral Dissertations

"A study of the chemical vapor deposition (CVD) of boron from boron triiodide (BI₃) on molybdenum has been done with field emission microscopy (FEM) and low energy electron diffraction (LEED).

A correlation of the efficiency by which BI₃ is effectively dissociated to form adsorbed boron, and the temperature of the substrate has been shown through work function measurements on the boron covered molybdenum field emitter surfaces. The boron-induced work function change of molybdenum has been shown to be in agreement with a theoretical model which predicts positive, as well as negative work functions for adsorbate-substrate systems. It …

Polynary Telluride Glasses Containing Silver, H. E. Anthonis, N. J. Kreidl

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Pbo Transformation Induced By Water, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Phase Transformations In The System Zro₂-Cao, Damri Sukhotanang

Masters Theses

"Thermal expansion, thermal hysteresis, and the monoclinic tetragonal phase transformation of ZrO₂ have been studied with high temperature x-ray diffractometry. The initial transformation temperature in pure ZrO₂, on heating, is about 1150ºC. The transformation occurs over a 100ºC temperature range and thermal hysteresis occurs on heating and cooling. The mechanism of the transformation is related to preferred vibrational modes of atoms on the A_O -C_O plane of the monoclinic structure. Because the monoclinic B_O axis is parallel with the tetragonal [110] axis, structural relationships can be seen to be a controlling factor in the transformation. Initiation of …

A Mass Spectrometric Characterization Of Positive Ions Created In Simple Vacuum Diodes Incorporating Oxide Cathodes With Supplementary Analysis Of Background Gases, Larry A. Addington

Masters Theses

"Simple diodes were constructed utilizing oxide cathodes and nickel anodes. The cathodes were obtained by applying a mixture of barium, strontium, and calcium carbonates to a nickel filament and decomposing them to yield the oxides. The products of decomposition were analyzed by monitoring the composition of the background gases in the vacuum chamber. A portion of the flux of positive ions bombarding the cathode during diode operation was analyzed. It was possible to determine the region of origin of the ions and their potential energy at the time of formation. Positive ions of chlorine, fluorine, sodium, potassium, and rubidium were …

A Study Of The System Lithia - Silica, Roy Richard Ramey

Masters Theses

"X-ray intensity and d-spacing measurements were performed upon samples in the system Li₂O-SiO₂. Samples ranged from 0.0 to 28.0 mole percent lithia and were fired for 72 hours at temperatures from 920ºC to 1400ºC. Atomic absorption analyses were made upon the fired samples. Non-equilibrium conditions were prevalent and results are inclusive. Quartz is the stable phase in the high silica field at temperatures below 1050ºC with cristobalite stable above that. The quartz - cristobalite transformation occurs at 950ºC with the cristobalite transforming into tridymite at 1010ºC. There was wide scattering of data at 1000ºC and below. There was no correlation …

A Tensi-Volumetric Apparatus: Theory, Calibration, And Use In An Investigation Of The Oxygen Non-Stoichiometry Of Pure Batio₃, Glenn Jon Conger

Masters Theses

"The development of the tensi-volumetric apparatus has been traced to its current position of significance in studies relating to oxide non-stoichiometry. Components of the tensi-volumetric apparatus, especially the capacitance membrane manometer, were examined in detail as were the parameters affecting the performance of such an apparatus. Based on a careful consideration of components and performance, a tensi-volumetric apparatus has been designed, built, and its operation theoretically justified for its particular physical configuration. Results of existing studies of the oxygen non-stoichiometry of barium titanate have been used to predict its behavior during a tensi-volumetric study. Specific analytical procedures developed for use …

Concentration By Sorting : Feasibility Determination By Radial Distribution Analysis, Robert M. Doerr

Masters Theses

"A method was developed for determining certain factors for assessing the feasibility of sorting fragments of an inhomogeneous solid to concentrate a species. These factors are the typical size of zones in which the grade exceeds a selected value, and the recovery potentially achievable by sorting fragments of such size"--Abstract, page iii.

Polynary Silicon Tellurium Glasses, Henry Edward Anthonis

Masters Theses

"The introduction of Ag into Si-As-Te glasses permits the incorporation of Se, otherwise volatile and/or degradable as a constituent in Si-containing chalcogenide glasses. Si-As-Ag-Te-Se glasses exhibit much higher softening ranges and glass transition temperatures than encountered in known chalcogenide systems. A glass Si₃₅As₁₅Ag₁₀Te₂₀Se₂₀ had the viscosity log η =13 at about 500°C, as compared to 370°C for the base glass Si₃₅As₂₅Te₄₀, the viscosity of log η = 9.8 at about 560°C, as compared to 442°C for the base glass Si₃₅As₂₅Te_{40 …}

Synthesis And Properties Of Cadmium Manganese Ferrites, B. W. Jong

Doctoral Dissertations

"The formation sequence of (Cd,Mn,Fe) (Mn,Fe)₂O₄ from the individual oxides,x CdO + (1-x) MnCO₃ + α-Fe₂O₃,was found by X-Ray diffraction. Cd(Mn,Fe)₂O₄ was formed completely from CdO·Fe₂O₃ and CdO·Fe₂O₄ at 900°C and reacted with MnFe₂O₄ for 0 < x < 0.5 and with α-Fe₂O₃ for 0.5 < x < 1.0 to form a single phase of (Cd,Mn,Fe) (Mn,Fe)₂O₄ at 1150°C. This is the first time that the details involved in the formation sequence of CdMn-ferrite have been shown. A mixture of 0.5 CdO + 0.5 MnCO₃ + α-Fe₂O₃ was calcined at 900°C for 2 hrs forming Cd(Mn,Fe)₂O₄ with no Cd present in the other phases. Sintering was accomplished at 1150°C for 30 minutes forming a single phase of Cd₀.₅Mn₀.₅Fe₂O₄ with a bulk sintered density of 98-99% of the X-Ray density. The rate of changing density followed the relationship, p = K ln t + c, at temperatures between 1050°C and 1300°C. Magnetic properties of CdₓMn₁₋ₓFe₂O₄ were affected by composition x. A relationship, B = gx + h, was found between maximum magnetic flux density B and composition x at room temperature for 0 <̲ x <̲ 0.3. This was rationalized by a modification of Néel's theory. The maximum magnetic flux density decreased with increasing cadmium concentration for 0.3 < x <̲ 0.5. This decrease was attributed to the changing direction of the magnetic moment in the octahedral site sub-lattice according to the superexchange theory. No magnetic properties were observed due to the formation of a compensated antiferromagnetic phase for 0.5 < x <̲ 1.0. Maximum magnetic flux density increased with bulk density, while the coercive force decreased with the grain growth and the initial permeability increased with the bulk density and grain size. A stator core used for a-c electric motor application was formed by pre-sintering at 900⁰C for 2 hrs. Slots were then sawed with a tungsten carbide blade and final sintering was accomplished at 1150⁰C for 1 hr"--Abstract, pages iii-iv.

A Study Of The Solid Regions In The System Zr-Te, Frances Dolores Jenkins

Doctoral Dissertations

"Relative intensity measurements of X-ray powder diffraction lines were made of compositions in the region ZrTe₀.₅ to ZrTe₂.₀, fired between 600º and 817ºC in evacuated sealed tubes. The experimental relative intensities of samples between ZrTe and ZrTe₂ were compared with values calculated for several theoretical models with different Zr vacancy ordering schemes and Te vacancy concentrations. The most probable structural model for compositions in the range ZrTe to ZrTe₁.₅ is one in which the number of Zr vacancies located at z = 0 ranges from 0% to 30%, with the concentration of Te vacancies ranging from 0 to 35%. A …

Liquid Viscosity Measurement Using A Buret: An Instructional Technique, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Mixed‐Cation Effect In Silver Borate Glasses, E. N. Boulos, N. J. Kreidl

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.