Other Engineering Science and Materials Commons^™

A Threshold Helium Leakage Detection Switch With Ultra Low Power Operation, Sulaiman Mohaidat, Fadi M. Alsaleem

Department of Mechanical and Materials Engineering: Faculty Publications

Detecting helium leakage is important in many applications, such as in dry cask nuclear waste storage systems. This work develops a helium detection system based on the relative permittivity (dielectric constant) difference between air and helium. This difference changes the status of an electrostatic microelectromechanical system (MEMS) switch. The switch is a capacitive-based device and requires a very negligible amount of power. Exciting the switch’s electrical resonance enhances the MEMS switch sensitivity to detect low helium concentration. This work simulates two different MEMS switch configurations: a cantilever-based MEMS modeled as a single-degreefreedom model and a clamped-clamped beam MEMS molded using …

Crystalline–Amorphous Nanostructures: Microstructure, Property And Modelling, Binqiang Wei, Lin Li, Lin Shao, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Crystalline metals generally exhibit good deformability but low strength and poor irradiation tolerance. Amorphous materials in general display poor deformability but high strength and good irradiation tolerance. Interestingly, refining characteristic size can enhance the flow strength of crystalline metals and the deformability of amorphous materials. Thus, crystalline–amorphous nanostructures can exhibit an enhanced strength and an improved plastic flow stability. In addition, high-density interfaces can trap radiation-induced defects and accommodate free volume fluctuation. In this article, we review crystalline–amorphous nanocomposites with characteristic microstructures including nanolaminates, core–shell microstructures, and crystalline/amorphous-based dual-phase nanocomposites. The focus is put on synthesis of characteristic microstructures, deformation …

Plasmon Enhanced Quantum Properties Of Single Photon Emitters With Hybrid Hexagonal Boron Nitride Silver Nanocube Systems, Mohammadjavad Dowran, Andrew Butler, Suvechhya Lamichhane, Adam Erickson, Ufuk Kilic, Sy_Hwang Liou, Christos Argyropoulos, A. Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

Hexagonal boron nitride (hBN) has emerged as a promising ultrathin host of single photon emitters (SPEs) with favorable quantum properties at room temperature, making it a highly desirable element for integrated quantum photonic networks. One major challenge of using these SPEs in such applications is their low quantum efficiency. Recent studies have reported an improvement in quantum efficiency by up to two orders of magnitude when integrating an ensemble of emitters such as boron vacancy defects in multilayered hBN flakes embedded within metallic nanocavities. However, these experiments have not been extended to SPEs and are mainly focused on multiphoton effects. …

Graphene Twistronics: Tuning The Absorption Spectrum And Achieving Metamaterial Properties, Ammar Armghan, Meshari Alsharari, Khaled Aliqab, Osamah Alsalman, Juveriya Parmar, Shobhit K. Patel

Department of Mechanical and Materials Engineering: Faculty Publications

Graphene twistronics using multilayer graphene is presented in such a way that it provides a metamaterial effect. This manuscript also analyzes the prediction of behavior using machine learning. The metamaterial effect is achieved by twisting the graphene layers. Graphene twistronics is a new concept for changing the electrical and optical properties of bilayer graphene by applying a small angle twist between the layers. The angle twists of 5^o, 10^o, and 15^o are analyzed for the proposed graphene twistronics design. Tuning in the absorption spectrum is achieved by applying small twists to the angles of the …

Heterogeneous Sensor Data Fusion For Multiscale, Shape Agnostic Flaw Detection In Laser Powder Bed Fusion Additive Manufacturing, Benjamin Bevans, Christopher Barrett, Thomas Spears, Aniruddha Gaikwad, Alex Riensche, Harold (Scott) Halliday, Prahalada Rao

Department of Mechanical and Materials Engineering: Faculty Publications

We developed and applied a novel approach for shape agnostic detection of multiscale flaws in laser powder bed fusion (LPBF) additive manufacturing using heterogenous in-situ sensor data. Flaws in LPBF range from porosity at the micro-scale (< 100 μm), layer related inconsistencies at the meso-scale (100 μm to 1 mm) and geometry-related flaws at the macroscale (> 1 mm). Existing data-driven models are primarily focused on detecting a specific type of LPBF flaw using signals from one type of sensor. Such approaches, which are trained on data from simple cuboid and cylindrical-shaped coupons, have met limited success when used for detecting multiscale flaws in complex LPBF parts. The objective of this work is to develop a heterogenous sensor data fusion …

Multifunctional Microgel-Based Cream Hydrogels For Postoperative Abdominal Adhesion Prevention, Bo Liu, Yunfan Kong, Olawale A. Alimi, Mitchell Kuss, Huiyin Tu, Wenfeng Hu, Abu Rafay, Kumar Vikas, Wen Shi, Megan Lerner, William L. Berry, Yulong Li, Mark A. Carlson, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

Postoperative abdominal adhesions are a common problem after surgery and can produce serious complications. Current anti-adhesive strategies focus mostly on physical barriers and are unsatisfactory and inefficient. In this study, we designed and synthesized advanced injectable cream-like hydrogels with multiple functionalities, including rapid gelation, self-healing, anti-oxidation, anti-inflammation, and anti-cellular adhesion. The multifunctional hydrogels were facilely formed by the conjugation reaction of epigallocatechin gallate (EGCG) and hyaluronic acid (HA)-based microgels and polyvinyl alcohol (PVA) based on the dynamic boronic ester bond. The physicochemical properties of the hydrogels including anti-oxidative and anti-inflammatory activities were systematically characterized. A mouse cecum-abdominal wall adhesion model …

Influence Of Processed Natural Black Sand Vs. Natural White Sand And Silica Flour As Additives To Oil-Well Cementing Applications, Ramy Abuel Maaty

Theses and Dissertations

Cementing is a crucial and fundamental step in the process of drilling wells to extract oil from its reservoirs. Cementing main functions are to achieve zonal isolation and provide mechanical support to the casing. Impermeable and powerful cement is strongly desired to withstand high pressures and temperatures during the lifetime of the producing wells. Various additives to cement, such as silica flour, fly ash, Nano-additives and other advanced materials have been used and tested to attain improved cement of higher quality and enhanced properties such as permeability, porosity, mechanical and rheological properties. Very few researches have discussed the uses of …

Electromagnetic Theory And Applications, Nicholas Madamopoulos, George Kliros

Open Educational Resources

This book intends to provide both the fundamentals of Electromagnetics but also some practical applications of the concepts covered. Having taught electromagnetics for several years, the authors feel that many times the field of electromagnetics comes as “old” and often times students do not appreciate the concepts and their importance in everyday applications. The authors intend to accompany the EM concepts with life applications. Hence, students may see the direct impact of the knowledge they acquire through the study of the field of electromagnetics and better appreciate the field.

Neutralization Of Fuel Tankering Emissions For Environmental Sustainability, Peter O'Reilly, Maria Petrescu, Fabricio Sulzbacher, Diogo Coutinho

National Training Aircraft Symposium (NTAS)

As aviation has been one of the fastest-growing sources of emissions, this paper explores sustainable solutions in the equation of the economic savings from the fuel tankering practice, in a way it could represent gains of credibility for this industry (Boussauw & Vanoutrive, 2019). The fuel expenses in Brazil have been responsible for the highest operational cost for the airlines and, as a result, there has been an ongoing pursuit of the highest level of efficiency (ANAC, 2019). In this context, this study has been focused on the emerging Brazilian aviation market, and uses primary data collected from three major …

Interfaces In Dynamic Brittle Fracture Of Pmma: A Peridynamic Analysis, Longzhen Wang, Javad Mehrmashhadi, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

Recent experiments in bonded PMMA layers have shown dramatic changes in dynamic crack growth characteristics depending on the interface location and toughness. In this paper we present a peridynamic (PD) analysis of this phenomenon and determine three elements that are essential in a model reproducing the observed fracture behavior: (1) softening near the crack tip to account for changes in PMMA due to heat-generation induced by the high strain rates reached around the crack tip in dynamic fracture; (2) independent extension (mode I) and shear (mode II) modes of fracture; (3) a two-parameter fracture model, which matches both strength and …

Locally Resonant Metasurface For Low-Frequency Transmissive Underwater Acoustic Waves, Zhong Chen, Shenghong Guan, Qiang Xie, Zheng Li, Zhongmei Gao, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Acoustic metasurfaces for underwater wave manipulation have great potential use, but the strong solid-fluid interaction caused by impedance closeness between the structure and water brings design difficulty, especially in the low-frequency range.

Methods: Here a locally resonant metasurface for transmissive underwater acoustic waves is proposed using finite element method for which each metasurface unit consists of one channel and three subunits. Each subunit has one plate and two rubber spacers to form a resonator. By changing the height ratio of the plate over the subunit, arbitrary phase shifts within the full 2π coverage can be obtained at …

An Efficient And Low-Cost Method To Create High-Density Nitrogen-Vacancy Centers In Cvd Diamond For Sensing Applications., Prem Bahadur Karki, Rupak Timalsina, Mohammadjavad Dowran, Ayodimeji E. Aregbesola, Abdelghani Laraoui, Kapildeb Ambal

Department of Mechanical and Materials Engineering: Faculty Publications

The negatively charged Nitrogen-Vacancy (NV^-) center in diamond is one of the most versatile and robust quantum sensors suitable for quantum technologies, including magnetic field and temperature sensors. For precision sensing applications, densely packed NV^- centers within a small volume are preferable due to benefiting from 1/√𝑁 sensitivity enhancement (N is the number of sensing NV centers) and efficient excitation of NV centers. However, methods for quickly and efficiently forming high concentrations of NV^- centers are in development stage. We report an efficient, low-cost method for creating high-density NV^- centers production from a relatively …

Correction: Nanoscale Imaging Of Antiferromagnetic Domains In Epitaxial Films Of Cr2o3 Via Scanning Diamond Magnetic Probe Microscopy, Adam Erickson, Syed Qamar Abbas Shah, Ather Mahmood, Ilja Fescenko, Rupak Timalsina, Christian H. Binek, Abdelghani Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

Correction for ‘Nanoscale imaging of antiferromagnetic domains in epitaxial films of Cr2O3 via scanning diamond magnetic probe microscopy’ by Adam Erickson et al., RSC Adv., 2023, 13, 178–185, https:// doi.org/10.1039/D2RA06440E

Traversing With Quantitative Fidelity Through The Glass Transition Of Amorphous Polymers: Modeling The Thermodynamic Dilatational Flow Of Polycarbonate, Mehrdad Negahban, Wenlong Li, Jean-Marc Saiter, Laurent Delbreilh, Kyle Strabala, Zheng Li

Department of Mechanical and Materials Engineering: Faculty Publications

We follow the assumption that the dilatational response of glassy polymers can be characterized by a back-stress type analog that includes a thermal expansion for each elastic component, and with a viscosity that is dependent on the expansion of the elastic back stress component. To this, we add the assumption of an unloaded equilibrium temperature that correlates to the past processing through the viscous flow. After setting this in a thermodynamically consistent structure, the elastic, elastic backstress, thermal expansion, back-stress thermal expansion, heat capacity and viscous damping are evaluated using existing experiments for the response of polycarbonate over the glassy …

Pinch Force Generation During Scaling By Dental Professionals: A Systematic Review, Jessica R. Suedbeck, Emily A. Ludwig

Dental Hygiene Faculty Publications

Objective

The objective of this review was to examine the impact of instrument designs on pinch force generation during scaling by dental professionals.

Methods

Three databases were utilized from September 2019 to November 2021 in addition to hand-searching specific journals and reference lists. Research articles that examined pinch force generation in dental professionals during scaling with manual instruments only were included. Bias was assessed in the individual articles.

Results

Six research articles were included with sample populations that varied from 12 to 24 participants. Four articles evaluated instrument designs in relation to pinch force generation during scaling by dental professionals. …

Peridynamic Simulation Of Elastic Wave Propagation By Applying The Boundary Conditions With The Surface Node Method, Francesco Scabbia, Mirco Zaccariotto, Ugo Galvanetto, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

Peridynamics is a novel nonlocal theory able to deal with discontinuities, such as crack initiation and propagation. Near the boundaries, due to the incomplete nonlocal region, the peridynamic surface effect is present, and its reduction relies on using a very small horizon, which ends up being expensive computationally. Furthermore, the imposition of nonlocal boundary conditions in a local way is often required. The surface node method has been proposed to solve both the aforementioned issues, providing enhanced accuracy near the boundaries of the body. This method has been verified in the cases of quasi-static elastic problems and diffusion problems evolving …

Advanced Modeling And Innovative Transcranial Magnetic Stimulation Coil Designs For The Treatment Of Neurological Disorders, Mohannad Tashli

Theses and Dissertations

Transcranial magnetic stimulation (TMS) is a safe, effective and non-invasive treatment for several mental and psychiatric disorders. TMS is an FDA approved treatment and is commonly applied to patients who do not respond to medications for the treatment of clinical depression, smoking cessation, obsessive-compulsive disorder and migraine. Recently, there has been an increase in the development of electromagnetic neuromodulation techniques targeted at enhancing the effectiveness of TMS devices for the treatment of mental diseases. In TMS stimulation, focality is an important factor which determines the specificity of the pulses induced in different brain tissues. The electromagnetic pulses must be confined …

Assessing A Byproduct Of The Cbd Ethanol Extraction Process For Potential As A Wood Finishing Product, Avani M. Flanagan

Masters Theses

Developments in regulations concerning the use of CBD products as therapeutic remedies have allowed the global cannabidiol (CBD) market to take off within the past five years. Despite producers of CBD oil wanting to optimize their methods and increase product yields, several waste streams still exist. During the winterization phase of the ethanol extraction process, CBD oil is cooled and filtered so the fats, waxes, and lipids from the Cannabis sativa plant can coagulate and be removed, creating a purer oil with higher potency but contributing to the 58% (crude weight) total loss that occurs throughout the process. The removed …

Understanding The Feasibility Of Improving Interfacial Properties In Direct Ink Writing Of Silicone-Polyurethane Resin Hybrid Material, Ayobami Samuel Akinfenwa

College of Graduate Studies: Theses & Dissertations

The progress in materials engineering and the ability to make various models possible have made soft robotics a popular alternative to traditional robotics. Still, soft robots need various parts, like Printed Circuit Boards (PCBs), batteries, cables, fittings, and more, to work correctly or to get attached to other complex parts. These parts can have different material properties, like elastic moduli, strength, etc. Because of these differences, mechanical failures happen at the points where two materials meet, making soft robots less durable and less lasting in real-life situations due to failure. Conventionally, the fabrication of soft robot parts is through moulding. …

Development Of Inconel 718f And Inconel 718e Powders For Parts Manufacturing Utilizing Binder Jet Three-Dimensional Printing And Compressed Pellet Methods, Duncan Eric Manor Ii

Graduate Theses, Dissertations, and Problem Reports (ETD)

Alloy Inconel 718 is a Ni based superalloy used for high temperature applications including turbine blades, turbocharger rotors and nuclear reactors. Inconel 718 is a popular commercial atomized powder that has limitations in performance for use in additive manufacturing applications due to poor part quality and efficiency of current fabrication methods. Developing new compositions and additive manufacturing (AM) methodologies of IN718 is critical to improve the quality and the efficiency of IN718 parts manufacturing. Developing new additive manufacturing methodology that produces higher quality parts made of IN718 as compared to current methods has the potential to greatly impact industry, academia, …

Fem Eem Dataset: Optimising Retrofitted Insulation For Irish Residential Building Walls, Rakshit D. Muddu, Aimee Byrne, Anthony Robinson Dr.

Datasets

A large number of combinations of Irish wall types, insulation materials, and heating fuel types were produced to compare the multiple variables which influence Optimal Insulation Thickness values. The total cost (TC) and carbon emission (CE) at optimum insulation thickness (OIT) for all combinations of insulation material and three types of fuel are considered. The dataset presents OIT for solid wall, cavity wall and cavity block wall types located in Monaghan, Dublin, and Kerry.