Other Engineering Science and Materials Commons^™

Fabrication Of Soft Gripper Via Direct Inkjet Writing Additive Manufacturing, Evan D. Johnson

Electronic Theses and Dissertations

Additive manufacturing (AM) has bloomed recently in the manufacturing field due to its many applications. Direct inkjet writing (DIW) is one of the main am technologies used in the production of grippers. DIW is the most popular taking advantage of materials like silicone and hydrogels. The technology of 3D printing with silicone is still in early stages ,nevertheless, the ability to print with soft materials is very alluring. The implementation of complex geometries in the silicone world would yield vast opportunities in the medical and robotics fields. Additive manufacturing allows for this to be thoroughly examined. In this research these …

Parameters That Influence The Performance Of Dispersion Barrier Coatings, Randy Raditya

Electronic Theses and Dissertations

Barrier coating layers are important in many paper grades used in food packaging and have the potential to help reduce our use of plastics in some situations. Barrier layers to produce water proof packaging such as milk or juice cartons or coffee cups are common. Water based dispersion barrier coatings have the potential to be a low-cost alternative to extrusion coated layers. Water borne coatings are reported to be easy to recycle and break down in the environment. However, barrier properties are often less than what is desired and expected for these water borne coatings. The reason for this poor …

Metal Thin Film Stiffness Extraction Technique For Surface Acoustic Wave Filters, Travis R. Weismeyer

Electronic Theses and Dissertations

Accurate knowledge of the surface acoustic wave (SAW) properties propagating at the surface of a piezoelectric substrate with thin films, electrodes or temperature compensated films, is critical in SAW filter design to meet the target frequency response, power durability and performance prior to device fabrication. While reliable material constants exist for substrates such as LiNbO3 used in SAW filters, the absolute elastic constants associated with operational thin films used for electrodes or temperature compensation do not exist. Although the bulk values of the constituent materials are known, the composite film/substrate properties are difficult to predict since they depend strongly on …

Coating Component Migration In Paper Coatings, Emilia Purington

Electronic Theses and Dissertations

In many applications such as in paints and coatings, pigments are mixed with polymeric binders to generate the final product. In the coating of paper, properties like strength, durability, and print quality are affected not only by the binder type, but the final location of the binder relative to the pigments and the fibers. During the application and drying of a paper coating, binder is known to migrate. A number of methods are available to measure the migration of latex or starch. However, all of these methods have some limitations, especially when starch, latex and kaolin are components of the …

Microwave Acoustic Saw Resonators For Stable High-Temperature Harsh-Environment Static And Dynamic Strain Sensing Applications, Anin K. Maskay

Electronic Theses and Dissertations

High-temperature, harsh-environment static and dynamic strain sensors are needed for industrial process monitoring and control, fault detection, structural health monitoring in power plant environments, steel and refractory material manufacturing, aerospace, and defense applications. Sensor operation in the aforementioned extreme environments require robust devices capable of sustaining the targeted high temperatures, while maintaining a stable sensor response. Current technologies face challenges regarding device or system size, complexity, operational temperature, or stability.

Surface acoustic wave (SAW) sensor technology using high temperature capable piezoelectric substrates and thin film technology has favorable properties such as robustness; miniature size; capability of mass production; reduced installation …

Structural And Aerodynamic Design, Procedure And Analysis Of A Small V-Shaped Vertical Axis Wind Turbine, Odari J. Whyte

Electronic Theses and Dissertations

Over the last two decades there has been a renewed interest in Vertical Axis Wind Turbines. This turbine configuration though unpopular for large-scale generation has found a niche market in the way of offshore energy harvesting. However, offshore wind has its challenges. In this thesis a detailed comprehensive study of a proposed V-shaped vertical axis turbine rotor is performed in order to examine its structural and aerodynamic characteristics. The design met and exceeded the safety parameters establish for test bed operation, showing a factor of safety of 1.87 with regard to fatigue stress response. A satisfactory fatigue stress design life …

The Development Of A Vacuum Forming System For Kydex® And Other Thermoplastic Sheet, Andrew G. Smith

Electronic Theses and Dissertations

Vacuum forming is a popular, cost effective method amongst large and small scale applications. The method is used to mold a material to the surface of a mold/pattern in order to create a negative copy for reproduction or an object in positive form. The prototype vacuum forming system developed and documented herein is of a membrane-seal type that consists of three (3) principle parts: radial platen, Hinged Frame and Platen Support Assembly, and a PVC surge tank. Each part is described in detail through design, manufacturing, and testing processes. The design supports functional versatility, small scale molding, and uses readily …

Data Driven Discovery Of Materials Properties., Fadoua Khmaissia

Electronic Theses and Dissertations

The high pace of nowadays industrial evolution is creating an urgent need to design new cost efficient materials that can satisfy both current and future demands. However, with the increase of structural and functional complexity of materials, the ability to rationally design new materials with a precise set of properties has become increasingly challenging. This basic observation has triggered the idea of applying machine learning techniques in the field, which was further encouraged by the launch of the Materials Genome Initiative (MGI) by the US government since 2011. In this work, we present a novel approach to apply machine learning …

Developing An Insider Threat Experimental Environment, Eric Ortiz

Electronic Theses and Dissertations

Simulated, 3D gaming environments have been used for a wide-range of applications including training, entertainment, and experimentation in an assortment of domains for some time. This can be attributed to their unique ability to emulate multifaceted situations that may be difficult to control, while affording participants the opportunity to operate in a relatively safe environment. In cybersecurity research, investigation of insider threat behavior is an endeavor that has received little attention in terms of available environments and resources for experimental manipulation. This research effort aimed to close this gap. A simulated, 3D gaming environment and accompanying scenarios were developed for …

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …