Other Engineering Science and Materials Commons^™

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Improving The Concrete Compressive And Flexural Strength With A Low Fraction Addition Of Carboxylated Nitro-Oxidized Cellulose Nanofibrils From Banana Rachis, Ngesa Ezekiel Mushi, Emmanuel Kagya

Tanzania Journal of Science

Conventionally, concrete strength depends on the bonding interface, especially in hydrated products such as calcium silicate hydrate (CSH). As a result, concrete is sensitive to tensile load. With its unique properties, a low fraction of carboxylated nitro-oxidized cellulose nanofibrils (NOCNF) from the banana rachis is employed to improve the mechanical performance of the concrete nanostructurally. Compressive and flexural strength using the NOCNF content at 0, 0.05, and 0.1 wt.%, cured for 7 and 28 days, were evaluated. Notably, the compressive strength increased by 16 % and the flexural strength by 13 % at 0.1 wt.% NOCNF compared to plain concrete …

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Characteristics Of Carbonaceous Materials Synthesized From Palm Oil Empty Fruit Bunch Waste Using Ferrocene Catalyst, Ahmad Nabil Shahab, Adinda Izzatul Islam, Afif Wardana, Ilham Nur Dimas Yahya, Ary Yanuar Tri Amalia, Nofrijon Sofyan, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The synthesis of carbonaceous materials for reduced graphene oxide (rGO) precursors using oil palm empty fruit bunches waste as a carbon source offers a sustainable solution for waste management in the palm oil industry while delivering high-performance materials. The oil palm empty fruit bunches were carbonized, followed by acid washing, pyrolysis with ferrocene (8%, 12%, and 16% variations), and ultrasonication to produce rGO. The structural, electronic, and morphological properties of the rGO were analyzed using various characterization techniques. The band gap values decreased with increasing ferrocene concentration, from 1.14 eV (8%) to 1.06 (16%), indicating enhanced electronic conductivity. XRD analysis …

Inspection Program Effectiveness Key Performance Indicator For Pressurized Static Equipment Integrity At Offshore Platform, Teuku Ahmad Haekal, Johny Wahyuadi Soedarsono, Badrul Munir, Muhammad Yudi Masduky Sholihin

Journal of Materials Exploration and Findings

One of the key challenges in asset integrity management system at offshore platform is the lack of visibility regarding performance issues and program effectiveness. Without proper performance measurement systems, it becomes difficult to address positive or negative trends promptly and for management to stay informed about the status and the impact of the inspection program. Therefore, Key Performance Indicator (KPI) is needed to measure inspection program effectiveness to prevent undesirable equipment failures that could lead to Loss of Primary Containment (LOPC) or Process Safety Event (PSE). The developed KPI is the ratio of the number of non-leak inspection findings with …

Effect Of Addition Monofilament And Multifilament Polypropylene Fibers On Mechanical Properties Of Concrete At Elevated Temperatures, Nourhan Osama Hanafy Dr

Journal of Engineering Research

Some researchers studied the effect of different types of fibers on the strengths of concrete at elevated temperature. However, there are some limitations in the study of the strengths of concrete using different methods of cooling after elevated temperature. Thus, the main objective of this research is to study the mechanical properties of concrete with the addition of 1% polypropylene fibers, featuring different structures, at elevated temperatures and with various cooling methods, compared to normal concrete. An experimental program using three different series of mixes, the first series included normal concrete (control) mix without fibers, the second series included 1% …

Usability Analysis Of The Ronnie Baugh (Oggun Ii) Tractor Using The Single Usability Metric [Research Note], John Lester Remot, John Kenneth Punongbayan, Stephanie Caridad Landicho, Alan Marco Mercado, Josefa Angelie Revilla, Omar Zubia

The Philippine Agricultural Scientist

Agricultural mechanization is one of the policies created by the Philippine government to alleviate systemic problems facing the country. In 2020, a local company was licensed to manufacture the American-designed Ronnie Baugh tractor (RBT), which aims to enable smaller-scale production with low-cost and customizable features. This study assessed the usability of the RBT and evaluated the appropriateness of its design for Filipino tractor operators using the single usability metric (SUM). A total of 21 participants were classified according to their age and experience (A – young and experienced, B – old and experienced, and C – young and inexperienced) and …

Thermal Performance Investigation Of Thermoelectric Cooling System With Various Hot-Side Cooling Methods, Bowo Y. Prasetyo, Parisya P. Rosulindo, Fujen Wang

Makara Journal of Technology

Thermoelectric devices have been widely used in various applications, including cooling and power generation. The potential application of thermoelectric cooling systems has been studied. However, these systems still face challenges in achieving optimal performance compared with other cooling systems. Several factors, including the hot-side cooling method, influence the performance of thermoelectric systems. This study aimed to investigate the effects of different hot-side cooling methods on the thermoelectric performance and thermal behavior of thermoelectric cooling systems. The testing methods involved the combination of the thermoelectric module with five hot-side heat exchangers, including a square heatsink, a round heatsink, a two-pipe heat …

Analysis Of Marine Zone Management In Disputed Island Territories, Khomsin Khomsin, Danar Guruh Pratomo, Ayu Isnania Zahra

Journal of Environmental Science and Sustainable Development

Indonesia has 17,204 islands registered, named, and coordinated by Geospatial Information Agency (BIG). The number of islands can threaten maritime boundary disputes between provinces, districts, and cities. One of the disputes is the claim over Pulau Tujuh, which is mutually contested for ownership by the Province of Bangka Belitung and the Province of Riau Islands. This study aims to analyze the marine management zone of the Pulau Tujuh claim. It is carried out using the cartometric method. This study of regional boundaries refers to the Regulation of The Minister of Home Affairs of The Republic of Indonesia 141 of 2017, …

Multi-Mode Regulation Of The Drying Process Of Industrial Gas, Isamidin Xakimovich Sidikov Pr, Nashvandova Gulruxsor Murot Qizi Phd

Technical science and innovation

Currently, much attention is paid to the issue of energy efficiency of gas processing enterprises. The continuous growth of world prices for energy resources requires constant improvement of the management system, providing the most optimal conditions for the flow of technological processes. A conceptual model of the heat-mass transfer process occurring in the absorber as an object of research has been developed, which characterizes the relationship of the variables involved in the drying process of natural gas, control, measurable and immeasurable, as well as controlled parameters have been selected, which are used to develop and study a mathematical model of …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Robust Gasification Trial Results For A Variety Of Difficult-To-Recycle Packaging-Related Materials, Bruce A. Welt

Journal of Applied Packaging Research

Currently, recycling requires nearly absolute sorting of materials to accommodate the limited capabilities of existing recycling infrastructure. Whether a material is “recyclable” depends more on the method of recycling than the material itself. Our dependence upon sorting has limited success of recycling and has stifled our ability to achieve circular economy sustainability with plastic packaging materials. Our dependence upon sorting is rooted in our material-specific recycling processes. However, newer robust recycling processes are commercially available that reduce or eliminate the need to sort waste, and can convert mixed waste into primary feedstock chemicals, such as methanol for subsequent manufacture of …

Detection And Identification Of Disturbances By Spectral Analysis Of Structure-Borne Noise During The Production Of A Sealing Seam, Felix Kruppa, Lars Meisenbach, Berend Oberdorfer Dr.-Ing., Bernd Wilke Prof. Dr.-Ing.

Journal of Applied Packaging Research

When sealing, disturbances or errors can occur that impair the quality of the sealing seam and, in the worst case, lead to leaks. It is therefore important to identify and eliminate defective packages during production and to minimize the elimination by readjusting machine parameters. The aim of this article is the clear identification of seam quality problems on a vertical forming, filling and sealing machine SVE2520 by evaluating process parameters during the manufacturing process. For this purpose, the structure-borne noise is measured for each seal in order to identify not-usual curves. These not-usual curves are related to different disturbances or …

Mathematical Model Of The Efficiency Of Investments Aimed In The Implementation Of Water-Saving Technologies

Irrigation and Melioration

In Uzbekistan, research work is being carried out aimed at improving the economic mechanisms for the introduction of water-saving technologies for irrigating agricultural crops. At the same time, the issues related to the analysis of the effectiveness of the use of water-saving technologies when irrigating cotton, the development of mathematical methods for assessing the effectiveness of investments, as well as their introduction into practice have not been sufficiently studied. This article provides a mathematical model of the efficiency of investments aimed at introducing water-saving technologies. The results of a numerical experiment of a mathematical model show that the introduction of …

Efficient Use Of Water Resources In The Basins Of Small Rivers, F. Gapparov, M.F. Gafforova

Irrigation and Melioration

The article provides a recommendation for the efficient use of water resources in the basins of small foothill rivers. The research was carried out on the example of the Govasay river basin located in the northern part of the Fergana Valley. The efficiency factor of the canal has been determined and a technical assessment has been given for the management of water resources in the river basin; the efficiency of the canal is 65-75%. A program for the operational management of water resources in The Govasay river basin and a GIS map of water consumers in the Govasay river basin …

Model Of Groundwater Level Control Using Horizontal Drainage, A. Arifjanov, M. Otaxonov, Z. Abdulkhaev

Irrigation and Melioration

The article describes the main factors affecting the rise in the level of groundwater in the city of Fergana and ways to eliminate them. Currently, in order to reduce the negative impact of rising groundwater levels on the environment, crops, buildings and structures, as well as underground utilities, it is proposed to design horizontal drainage in urban areas and a mathematical model has been developed for changing the groundwater level. For this, long-term data from observation wells were analyzed and the hydraulic parameters of horizontal drainage were selected taking into account the hydrogeology of the area. Taking into account the …

Results Of Proximate Analysis Of Energy Use Of Municipal Solid Waste, N.N. Abduganiev

Irrigation and Melioration

In the modern industrialized world, various raw materials are processed and used for human consumption. While some of the raw materials are converted into the desired product, the rest is thrown into the environment as waste. It is known that solid waste is a type of biomass that is formed in the course of human life. The article presents the results of a preliminary analysis of studies on the use of solid waste energy in the Urta-Chirchik district of the Tashkent region. Sorting results showed that the total volume of municipal solid waste in the district consists mainly of wood …

Shredding Of Cotton Stalks Under The Action Of Toothpicks In A Combined Unit, B. Khudayarov, U. Kuziev, B. Sarimsakov, М. Kholbutaev

Irrigation and Melioration

The article presents materials devoted to the justification of the parameters of the crown-wheel of the combined aggreagate. The technological process of work and the design of the working part, which is crushed by crushing cotton stalks, without breaking them, laying them on the movement of the unit, has been substantiated and developed. The optimal parameters of the crown-wheel and the tooth are determined by solving the regression equations that determine the optimal values of the vertical load on the teeth and its working quality. The results of theoretical and experimental research show that the amount of crushing of cotton …

Influence Of Electrophysical Methods On The Processes Of Root Formation Of Grapes, N.M. Markayev

Irrigation and Melioration

The article describes the possibilities of electrophysical processing before planting cuttings during vegetative cultivation of grape seedlings. The processes of root formation in cuttings using the electrophysical method in the article Acceleration of the process of root formation in cuttings of black raisins, treated at 71 V/m and an electric field strength of 15 hours, and an increase in the viability, quality, growth and survival of rooted seedlings up to 16.67-34% Presented the results of experiments on the increase and methods of electrotechnological processing of grape cuttings. The result of the study is the analysis and results of the processes …

Conditions, Criteria And Principles For Creating An Agri-Cultural Land Market In Uzbekistan, A.R. Nurnazarov

Irrigation and Melioration

The article analyzes the prerequisites for creating a market for agricultural land in the Republic of Uzbekistan, special attention is paid to land reform, land degradation (reduction of the bonitet score from 60 in 1991 to 50 or more at present, pasture degradation by 20-30%) and increase in economic from their use, the role of land rent in payments for land. 6 basic principles for creating a land market have been established and systematized, the relationship between X-rays and water in the irrigated farming zone, the role of the market in increasing the efficiency and effectiveness of the use of …

Economic Assessment Of The Effect Of Family Income On Students' Disciplines, Sh.A. Muratov

Irrigation and Melioration

The importance of higher education in scientific research, its role in poverty reduction and population growth has been studied theoretically. Also, when using the data of social surveys conducted by 538 respondents (students) studying in higher education institutions, they were awarded the Order of the logistics regulator in the economic assessment of the factors influencing the rate of mastery of disciplines. Factors influencing the acquisition of subjects by students: the main income of the family comes from non-farm (69,9 %), sex (52,2 %), studying at a higher education institution on a state grant (108,8 %), the student's course of study …

Innovative Rotor Casing And Leveling Apron For Combined Tillage Machine, A.A. Akhmetov, L.B. Muratov

Irrigation and Melioration

Investigations of the design of a combined machine equipped with an innovative casing and a leveler apron are presented, and the parameters of the leveler apron are substantiated. It was experimentally established that when the height of the drawing prism is exceeded by more than 200 mm, due to the falling of the crumbling part of the soil onto the rotor, the soil is thrown forward in the direction of the machine. Therefore, to eliminate soil waste, it is necessary either to reduce the height of the drag prism, or to increase the distance between the rotor and the leveling …

Ensuring The Uniformity Of Movement Of The Working Bodies Of The Machine For Processing Ridges In The Depth Of Travel, А. Tukhtakuziev, K.G. Abdulkhaev

Irrigation and Melioration

The article theoretically investigates the issue of identifying ways to ensure the deepening of the working bodies of the machine for processing ridges to a given processing depth and its required uniformity of stroke. The research results show that the deepening of the working bodies of the ridges processing machine to a given processing depth and its required uniformity is provided mainly due to the correct choice of the vertical distance from its reference plane to the lower connection points. The novelty of the conducted research lies in the fact that an analytical dependence has been obtained that allows us …

Develepment Of Land Market In Eastern European Countries And Experience For Uzbekistan, A.R. Nurnazarov

Irrigation and Melioration

The article examines the experience of the formation of the agricultural land market in Eastern European countries since the 90 s of the twentieth century, the problems and features of its devel-opment, the impact of the land market on the economies of countries. Particular attention is paid to the transformation of land ownership, methods of land privatization, land pricing, restrictions on land purchase, regulation of land relations in market conditions, issues of granting the right to pur-chase land to foreign individuals and legal entities, requirements for land owners for the presence of a special agricultural education or 3-5 years of …

The Developmet Of Competences Via Techniques For Enhancing Esp (English For Specific Purposes) Vocabulary Of Learners, G. Eshchanova

Irrigation and Melioration

In the article a recent trend in higher education is ESP (English for Specific Purposes) courses is discussed. These courses are designed around students’ needs based on their field of study. The goal is to strengthen students’ proficiency and help them to get ready to cope with everyday situations and deal with professionals in many fields such as: engineering, medicine, education and IT. There are many training sessions organized by international experts whose goal is to train local teachers to teach these courses successfully. In order to develop an ability to learn new vocabulary, for both general English and technical …

Development Of Girls’ Sports, A.R. Khodjanov, V.V. Mahmudov

Irrigation and Melioration

The article addresses current issues of higher education, taking into account its specifics. She has been providing appropriate advice on improving girls' physical well-being. The use of opportunities and qualities has an impact on the creation of comfortable conditions for female athletes. For girls involved in sports, the creation of impressive quality and possible conditions is considered. As a result, the girls-athletes of our institute took 2-3 places in the district and city qualifying rounds of chess, table tennis and won a ticket to the republican stage. At the republican stage, 2 female students of our team took 4th place …

The Imrovement Of Esp Teaching Via Methodical Provision At Technical Institution: Specializm-Oriented English Via Agriculture, G. Eshchanova, U. Nullaev

Irrigation and Melioration

In the given article the ways that ESP combines subject matter and English language teaching is discussed. This approach can be highly motivating for students because students are able to apply what they learn in their English classes to their main field of study, whether it be law, computing, business, tourism, etc. Being able to use the vocabulary and structures that they learn in a meaningful context reinforces what is taught and increases their motivation. Nevertheless, ESP concentrates more on language in context than on teaching grammar and language structures. Additionally, the ways of teaching English in ESL classes and …

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Justification Of The Main Parameters And Operating Modes Of The Crushers-Shredders Of Coarse Feed, K.D. Astanakulov, F.U. Karshiev, Sh.Kh. Gapparov

Irrigation and Melioration

The article presents the results of research on the justification of the parameters of the working bodies and operating modes of the mini crushers-shredders of coarse feed. On the basis of experimental research to study the effect of the rotor parameters Mini Crusher its qualitative performance indicators. According to the teachings found that rational parametres and operating modes-Crusher are: rotor length 350 mm; rotor diameter 550 mm; rotor speed 1290 min-1; the number of hammers 20 pcs; angle of rotation of the hammers 60.

Plan Dimensions Of The Flow Confinited By Cross Dams, On Rivers With Non-Symmetric Flooring, M.R. Bakiev, U.A. Kahhorov, A.А. Jakhonov

Irrigation and Melioration

Improving methods and technologies for calculating and designing floodplain transverse dams, taking into account the interaction of floodplain and riverbed flows to protect the banks from erosion and regulate riverbeds is one of the most important tasks. At the same time, the priority remains the transverse blind dams made of local soil with the attachment of their head. Their construction on rivers with two-sided asymmetric floodplains has its own characteristics, which consist in the need to take into account the morphology, the different roughness of the floodplain and the channel, the interaction of floodplain and channel flows, the asymmetry of …