Other Engineering Science and Materials Commons^™

Expansion Of Laser Peening Application With A High-Power Microchip Laser On A Robotic Arm, Yuji Sano, Yoshio Mizuta, Satoshi Tamaki, Tomonao Hosokai, Tomoharu Kato, Yoshihiro Sakino, Volker Schneidau, Sebastian Holz, Jörg Behler

15th International Conference on Shot Peening

Laser peening (LP) introduces compressive residual stress (RS) onto the surface of metallic materials using nanosecond laser pulses irradiated through a water layer, thereby effectively suppressing fatigue crack initiation. However, conventional LP systems require large, stationary setups, restricting their use to indoor environments. To overcome this limitation, a portable LP device featuring a finger-sized microchip laser mounted on a collaborative robot arm has been developed. Equipped with a compact power supply and a water circulation/recovery system, the device can operate on-site with minimal setup. Successful processing across various materials has confirmed both compressive RS induction and fatigue life extension. Notably, …

Power-Beaming: Wireless Energy Transfer Using Lasers, Spencer L. Barnett

ATU Scholars Symposium

The objective of the project is to implement a wireless energy transfer system utilizing laser technology. This system involves modulating the laser’s beam profile and spatial distribution through precise optical manipulation. The energy transmitted by the laser is captured by a photovoltaic array, commonly referred to as a solar panel, which is engineered to convert incident photons into direct current (DC) electrical power. The current challenge is to develop a reliable wireless energy transfer mechanism capable of operating over extended distances, thereby overcoming the constraints imposed by wired connections, particularly in environments where wiring is impractical, such as in space. …

Preserve Your Hma Pavements From The Start, Tim Zahrn, Andrew Eicher

Purdue Road School

This presentation will review sustainable preservation treatments and their application timeline to extend the life of asphalt pavement. We will discuss how pre-preservation treatments like a void reducing asphalt membrane, early-life preservation treatments such as rapid penetrating emulsion, and topical rejuvenators can reduce future maintenance and delay reconstruction. We will also look at mid-life treatments, such as micro-surfacing, fit into a preventative maintenance preservation plan. And finally cover end of life cold pavement recycling alternatives.

Biocorrosion Analysis Via Multiscale Time Series Analysis, Victor Hugo Mendoza Vejar, Eliseo Hernandez Martinez, Hector Puebla

Annual Symposium on Biomathematics and Ecology Education and Research

No abstract provided.

Neutralization Of Fuel Tankering Emissions For Environmental Sustainability, Peter O'Reilly, Maria Petrescu, Fabricio Sulzbacher, Diogo Coutinho

National Training Aircraft Symposium (NTAS)

As aviation has been one of the fastest-growing sources of emissions, this paper explores sustainable solutions in the equation of the economic savings from the fuel tankering practice, in a way it could represent gains of credibility for this industry (Boussauw & Vanoutrive, 2019). The fuel expenses in Brazil have been responsible for the highest operational cost for the airlines and, as a result, there has been an ongoing pursuit of the highest level of efficiency (ANAC, 2019). In this context, this study has been focused on the emerging Brazilian aviation market, and uses primary data collected from three major …

3d Printing Of Piezoelectric Materials And Devices, Dominic Polletta, Zack Myrtle

Thinking Matters Symposium

The design goal of the project is to use a stock 3D printer to 3D print materials with piezoelectric properties by adding Barium Titanate nanoparticles to the UV resin. The result of the printed material will be a device that will produce a charge when subjected to vibrations or stress. These printed devices can be used as microphones and other vibration sensors in a variety of applications. This process will be achieved by modifying the 3D printer by changing the film in the resin vat of the printer with a conductive film. This will allow for applied voltage to create …

Simulating Dynamic Failure Of Polymer-Bonded Explosives Under Periodic Excitation, Rachel Kohler, Camilo Duarte Cordon, Marisol Koslowski

The Summer Undergraduate Research Fellowship (SURF) Symposium

Accidental mishandling of explosive materials leads to thousands of injuries in the US every year. Understanding the mechanisms behind the detonation process is crucial to prevent such accidents. In polymer-bonded explosives (PBX), high-frequency mechanical excitation generates thermal energy and can lead to an increase in temperature and vapor pressure, and potentially the initiation of the detonation process. However, the mechanisms behind this energy release, such as the effects of dynamic fracture and friction, are not well understood. Experimental data is difficult to collect due to the different time scales of reactions and vibrations, so research is aided by running simulations …

On The Microstructure And Properties Of The Pmig Welding Joint Of A7n01 Aluminum Alloy Enhanced By Supersonic Wave And Aging, Tainquan Liang, Qiumei Qin, Xiaomei Mo, Xiaolian Zhao, Jianmin Zeng

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Simulation Investigation Of Temperature Distribution In Large Aluminium Panel During Autoclave Age Forming Process, Yongqian Xu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Evaluation Of Ductile Damage In Forging, Miroslav Urbanek

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Numerical Simulation And Experiments Analysis On Stiffness Control Mechanism Of Hyperboloid Shallow Shells, Zhao Lihong, Yu Haiping, Xing Zhongwen, Lei Chengxi, Wu Bin

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Multiscale Modeling Of Thermal Properties For Graphene–Polymer Nanocomposites, Maoyuan Li

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Mpfem Simulation On 2d Compaction Of Core–Shell Particulate Composites, Yu Liu, Fen Huang, Peng Han, Xizhong An, Haitao Fu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Detecting Rule Of Balance In Photography, Uyen T. Mai, Feng Liu

Student Research Symposium

Rule of Balance is one of the most important composition rules in photography, which can be used as a standard for photo quality assessment. The rule of balance states that images with evenly distributed visual elements are visually pleasing and thus are highly aesthetic. This work presents a method to automatically classify balanced and unbalanced images. Detecting the rule of balance requires a robust technique to locate and analyze important objects and visual elements, which involves understanding of the image content. Since semantic understanding is currently beyond the state of the art in computer vision, we employ the saliency maps …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Plastic Deformation Of Astm A36 Steel Using Two-Stage Light Gas Gun, Shawoon Kumar Roy

College of Engineering: Graduate Celebration Programs

To characterize material deformation in high velocity impact. To validate material models for computation simulation purposes.

This ongoing research is an attempt to study the plastic deformation of A36 steel plate (0.5” thick) under hypervelocity impact. Plastic deformation of the target plate was simulated using finite element software LS-DYNA.

Analysis Of Bolted Joints Under Medium And High Impact Loading, Deepak Sankar Somasundaram, Mohamed Trabia, Brendan J. O'Toole

College of Engineering: Graduate Celebration Programs

• Develop test fixture for medium impact study on bolted joints
• Create FEA model that can replicate the experiment
• Develop test fixture for high impact loading
• Create FEA model and select material properties that can produce results that
  closely match experiments.
• Compare different modeling techniques for high impact loading