Other Engineering Science and Materials Commons^™

Improving The Concrete Compressive And Flexural Strength With A Low Fraction Addition Of Carboxylated Nitro-Oxidized Cellulose Nanofibrils From Banana Rachis, Ngesa Ezekiel Mushi, Emmanuel Kagya

Tanzania Journal of Science

Conventionally, concrete strength depends on the bonding interface, especially in hydrated products such as calcium silicate hydrate (CSH). As a result, concrete is sensitive to tensile load. With its unique properties, a low fraction of carboxylated nitro-oxidized cellulose nanofibrils (NOCNF) from the banana rachis is employed to improve the mechanical performance of the concrete nanostructurally. Compressive and flexural strength using the NOCNF content at 0, 0.05, and 0.1 wt.%, cured for 7 and 28 days, were evaluated. Notably, the compressive strength increased by 16 % and the flexural strength by 13 % at 0.1 wt.% NOCNF compared to plain concrete …

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

An Analytical Framework For Quantifying Urban And Community Resilience To Natural Hazards From Cell-Phone Gps-Location And Traffic-Flow Data, Georgios Chatzikyriakidis

Civil and Environmental Engineering Theses and Dissertations

Urban areas are increasingly exposed to natural hazards while accommodating a growing share of the global population, yet a consistent science-based framework for quantifying urban and community resilience remains lacking. This dissertation develops a physics-based analytical framework grounded in statistical mechanics and the quantitative theory of Brownian motion. A city is conceptualized as a complex medium in which citizens move analogously to Brownian particles within a viscoelastic environment, influenced by socioeconomic interactions and infrastructure functionality.

A central premise is that urban resilience, interpreted as engineering resilience (an outcome), can be quantified through a single metric: the mean-square displacement MSD=⟨r²(t)⟩, of …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Fem Eem Dataset: Optimising Retrofitted Insulation For Irish Residential Building Walls, Rakshit D. Muddu, Aimee Byrne, Anthony Robinson Dr.

Datasets

A large number of combinations of Irish wall types, insulation materials, and heating fuel types were produced to compare the multiple variables which influence Optimal Insulation Thickness values. The total cost (TC) and carbon emission (CE) at optimum insulation thickness (OIT) for all combinations of insulation material and three types of fuel are considered. The dataset presents OIT for solid wall, cavity wall and cavity block wall types located in Monaghan, Dublin, and Kerry.

Development Of Inconel 718f And Inconel 718e Powders For Parts Manufacturing Utilizing Binder Jet Three-Dimensional Printing And Compressed Pellet Methods, Duncan Eric Manor Ii

Graduate Theses, Dissertations, and Problem Reports (ETD)

Alloy Inconel 718 is a Ni based superalloy used for high temperature applications including turbine blades, turbocharger rotors and nuclear reactors. Inconel 718 is a popular commercial atomized powder that has limitations in performance for use in additive manufacturing applications due to poor part quality and efficiency of current fabrication methods. Developing new compositions and additive manufacturing (AM) methodologies of IN718 is critical to improve the quality and the efficiency of IN718 parts manufacturing. Developing new additive manufacturing methodology that produces higher quality parts made of IN718 as compared to current methods has the potential to greatly impact industry, academia, …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Research Trend Of Metal Matrix Composites Reinforced With Silica Extracted By Green Route: A Bibliometric Analysis, Rinku Datkhile, Meena Laad, Babaji Ghule

Library Philosophy and Practice (e-journal)

Metal Matrix Composites have acquired an important place in the engineering applications due to their distinctive characteristics such as high specific strength, lower specific gravity, improved material stiffness, better durability, enhanced creep and fatigue strength etc. Worldwide scientists are working on the improvement of mechanical properties of composite materials. The present work attempts to summarise all the research carried out on metal matrix composites reinforced with silica extracted by green route and provides up-to-date research material for researchers who are interested in the field of composites with metal matrices. Scopus databases and software such as Gephi Vos Viewer and Table2Net …

Application Of Laser Assisted Ultrasonic Nanocrystal Surface Modification On Aluminum And 3d Printed Titanium, Eman Hassan, Thomas Crouse

Williams Honors College, Honors Research Projects

A novel surface treatment, laser assisted ultrasonic nanocrystal surface modification (LA-UNSM), has proved effective in increasing surface hardness, and fatigue life. The objective of this research is to determine the effectiveness of this process on components created with additive manufacturing. To accomplish this, we investigated the effectiveness of LA-UNSM treatment on aluminum, a common 3d printed metal, and the effectiveness of LA-UNSM processing on 3d printed titanium. We first conducted our own literature review to assess the practicality of using this same treatment on aluminum. We then treated traditionally manufactured aluminum at varying levels of laser intensity to determine if …

Bio-Binder—Innovative Asphalt Technology, Amir Tabakovic

Articles

The global road network spans 16.3 million km [1], of which 5 million km is in the EU. These road networks fulfil major economic and social goals by facilitating the movement of goods and people throughout the EU, and are therefore of the utmost importance to the economic and social life of the EU [2]. National governments invest heavily in their road networks, e.g., in 2014, EUR 53.33 billion was invested in the development and maintenance of the EU road network [3]. Each year, the world produces 1.6 trillion tonnes of asphalt [4], of which 218 million tonnes is produced …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Jominy Hardenability Tester With In-Situ Heating, Luke Allen

Williams Honors College, Honors Research Projects

This project centers on building a Jominy Hardenability tester with In-Situ heating for the manufacturing lab at the University of Akron. A new process and setup will be designed using engineering concepts in order to make the testing more efficient and safer for the teaching and testing of metal hardness. The current Jominy testing setup has efficiency issues within the transfer of specimen from induction heater to testing rig. Our design will simplify the design by creating a test rig that removes the traveling aspect of the specimen which will limit the amount of premature cooling done and will be …

Tabletop Mechanical Tester, Jamie Dombroski, Brian English, Richard Leffler, Andrew Shirk

Williams Honors College, Honors Research Projects

The need for hands-on and face-to-face experiences in the engineering classroom is very great. The equations, principles, and concepts can all be learned, but without the visual and tactile application, these don’t always sink in or become concrete. A small-scale tensile test machine was designed, sourced, manufactured, and tested for the purpose of being applied in classroom settings to provide this experience to engineering students. Extensive research was performed concerning tensile machines on the market, the essential elements of which are the load cell, grips, crosshead, extensometer, motor, and frame. The raw materials for the frame were purchased and drawings …

Bear Minimum: Ultralight Composite Bear Canister, Rama B. Adajian, Adam C. Eisenbarth

Mechanical Engineering

The ultralight backpacking community needs a strong, easy to use, safe bear canister that is lighter than current market products for trekking in the backcountry. A full design of the lid for the bear canister is to be completed. This includes the locking mechanism to ensure it is bear proof, the interface between the lid and the canister, and the structure of the lid so it passes the strength and weight specifications. The lid, along with the already designed canister body, is to be manufactured with formal documentation. The lid will initially be tested separately and then with the canister …

Case Studies Of Cavity And External Wall Insulation Retrofitted Under The Irish Home Energy Saving Scheme: Technical Analysis And Occupant Perspectives, Aimee Byrne, Gerard Byrne, Garrett O'Donnell, Anthony Robinson

Articles

The residential sector represents 27% of primary energy consumption in Ireland. This paper examines the case study of the Irish government’s national grant scheme to encourage energy efficiency retrofit in private housing. That is the Home Energy Saving (HES) Scheme, later rebranded the Better Energy: Homes (BEH) Scheme. The methodology involved monitoring several homes immediately before and after retrofit alongside discussions with occupants. The examination focused on specific measures commonly introduced through the HES/BEH programme − cavity and external wall insulation. It has been found that a significant decrease in heat loss through the walls was measured in all cases. …

Preliminary Investigation Into The Rate Of Carbonation Of Concrete Blocks Under Normal Production Yard Conditions, Aimee Byrne, Eanna Nolan

Conference papers

The release of CO2 from calcination during the manufacture of cement can be partially or fully offset by the CO2 it naturally absorbs during its lifetime. This paper reports results from a preliminary investigation into the rate of carbonation in concrete blocks stacked in a production yard over a period of 6 months. The blocks were stacked in a normal manner under natural exposure conditions. Carbonation progress was determined by splitting the blocks and spraying the freshly exposed surface with a phenolphthalein solution at intervals over the test period. It was found that the rate of the carbonation front progression …

An Overview Of The Development Of Cement-Based Batteries For The Cathodic Protection Of Embedded Steel In Concrete, Aimee Byrne, Niall Holmes, Brian Norton

Conference papers

This paper presents an overview of the cement-based batteries developed in DIT for use in the cathodic protection of embedded steel in reinforced concrete undergoing chloride-induced corrosion. Cathodic protection delivers an external current (approximately 20mA per m2 of embedded steel) which effectively polarises the internal current generated during corrosion. The batteries developed in DIT comprise of a cement-based electrolyte containing different additives including sand, aggregate, salts, carbon black and plasticiser with protruding anode and cathode metal plates. These batteries produced an initial electrical output of 1.5V and 23mA through a 10 resistor as measured using data acquisition units and a …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Plastic Deformation Of Astm A36 Steel Using Two-Stage Light Gas Gun, Shawoon Kumar Roy

College of Engineering: Graduate Celebration Programs

To characterize material deformation in high velocity impact. To validate material models for computation simulation purposes.

This ongoing research is an attempt to study the plastic deformation of A36 steel plate (0.5” thick) under hypervelocity impact. Plastic deformation of the target plate was simulated using finite element software LS-DYNA.

Analysis Of Bolted Joints Under Medium And High Impact Loading, Deepak Sankar Somasundaram, Mohamed Trabia, Brendan J. O'Toole

College of Engineering: Graduate Celebration Programs

• Develop test fixture for medium impact study on bolted joints
• Create FEA model that can replicate the experiment
• Develop test fixture for high impact loading
• Create FEA model and select material properties that can produce results that
  closely match experiments.
• Compare different modeling techniques for high impact loading