Other Engineering Science and Materials Commons^™

Effect Of The Stacking Sequence And Number Of Ply Orientation In A Quasi-Isotropic Laminated Plate On In-Plane Shear Modulus And Failure Modes, Ann Larson

Master's Theses

Maximizing the shear modulus and strength, as well as predicting failure mode and location, when designing a stacking sequence of quasi-isotropic carbon fiber laminated plates is essential to predict stability, resistance to deformation, and overall stiffness of the structure. This research investigates the effect of the stacking sequence of quasi-isotropic laminated composite plate materials in accordance with ASTM D5379: Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method.

In this research, experimental testing and Finite Element Analysis (FEA) were first used on aluminum to validate the simulation process before applying it to composite materials. The …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

Understanding The Feasibility Of Improving Interfacial Properties In Direct Ink Writing Of Silicone-Polyurethane Resin Hybrid Material, Ayobami Samuel Akinfenwa

College of Graduate Studies: Theses & Dissertations

The progress in materials engineering and the ability to make various models possible have made soft robotics a popular alternative to traditional robotics. Still, soft robots need various parts, like Printed Circuit Boards (PCBs), batteries, cables, fittings, and more, to work correctly or to get attached to other complex parts. These parts can have different material properties, like elastic moduli, strength, etc. Because of these differences, mechanical failures happen at the points where two materials meet, making soft robots less durable and less lasting in real-life situations due to failure. Conventionally, the fabrication of soft robot parts is through moulding. …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

LSU New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Development Of A Marine Biodegradable Target Balloon, Blake Samuel Robinson, Arash Sam Akhavi, David Leonardo Albarran-Martinez

Materials Engineering

The US Navy utilizes PVC target balloons, known as Killer Tomatoes, that are inflated onboard a naval vessel then deployed into the ocean to calibrate a variety of weaponry. The Navy has requested the investigation of biodegradable polymers to replace the PVC in attempts to reduce ocean waste that is generated from the leftover PVC material. After communicating with American Pacific Plastic Fabricators (APPF), the current manufacturer of the Killer Tomatoes, we gained an understanding of the manufacturing process and the material requirements that would allow a new material to be integrated into their current process. Two proprietary, trial polymers …

Valorization Of Xylan In Agroforestry Waste Streams, Harrison Appiah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Valorization of Xylan in Agroforestry Waste Streams.

Harrison Appiah

Microwave-assisted deep eutectic solvent and gamma-valerolactone metallic chloride catalyzed conversion of xylan to furfural were investigated using a 2x3 factorial experimental design at two levels of percent microwave power, reaction time, and catalyst concentration. The levels of each factor studied were (20%, 60% microwave power, 2, 4 minutes, and 10, 20mg) respectively. The effect of three metallic chloride catalysts (LiCl, FeCl3.6H20, CuCl2) on the conversion of xylan to furfural was also investigated. The gamma-valerolactone-ferric chloride sent system exhibited the highest mean yield of furfural (56.50%). The next highest furfural yield of …

Effects Of Heat Treatment On The Dimensional Stability And Mechanical Properties Of Guadua Bamboo, Kade Schmitz, Skye Dascher, Shalto Dascher

Materials Engineering

Contributing to about 4% of particulate emissions, the construction industry is one of the largest polluters of the environment. In an effort to reduce emissions, BamCore has produced a dual panel wall system made of Guadua bamboo with a Douglas fir veneer. Bamboo is a highly renewable material with a fast growth rate and carbon sequestration abilities. This project investigates how heat treating Guadua bamboo influences its dimensional changes and mechanical properties for building applications. It was found that a dimensional increase in every direction occurred for all samples when exposed to higher relative humidity (50% to 90%), and that …

Structure-Property Relationships Of Polyisobutylene-Block-Polyamide Thermoplastic Elastomers, Morgan Dunn Heskett

Master's Theses

Thermoplastic elastomers (TPEs) are a class of polymer fit for a wide variety of applications due to their customizability. In the synthesis of these types of materials, an elastically-performing polymer, deemed the “soft block,” is combined with a stiffer “hard block” polymer, each of which can be selected based on their own specific properties in order to achieve desired material behavior in the final copolymer. Recently, the use of polyisobutylene as a soft block in combination with a polyamide hard block has been investigated for use in TPE synthesis. While the material showed some promising behavior, many properties were still …

First-Principles Studies Of Structure-Property Relationships: Enabling Design Of Functional Materials, Qunfei Zhou

Theses and Dissertations--Chemical and Materials Engineering

First-principles calculations based on quantum mechanics have been proved to be powerful for accurately regenerating experimental results, uncovering underlying myths of experimental phenomena, and accelerating the design of innovative materials. This work has been motivated by the demand to design next-generation thermionic emitting cathodes and techniques to allow for synthesis of photo-responsive polymers on complex surfaces with controlled thickness and patterns. For Os-coated tungsten thermionic dispenser cathodes, we used first-principles methods to explore the bulk and surface properties of W-Os alloys in order to explain the previously observed experimental phenomena that thermionic emission varies significantly with W-Os alloy composition. Meanwhile, …

Predictive Modeling Of Oxygen Transmission Through Micro-Perforations For Packaging Applications, Ayman Abdellatief, Bruce A. Welt, Jason Butler, Eric Mclamore, Arthur Teixeira, Sanjay Shukla

Journal of Applied Packaging Research

Methods for creating precise perforations in respiring produce packaging are being increasingly adopted. Knowledge of oxygen transfer through perforated packaging and oxygen distribution in packages is necessary for successful packaging design of fresh produce. An approach to modeling perforated packaging performance was developed using a cylindrical chamber with precision perforations using Fick’s second law. The model was simulated using two techniques including Finite Element Method (FEM) using commercially available software and Finite Volume Method (FVM) through programming. Perforations were approximated as a source term in the second method. Both simulation techniques showed trends similar to experimental data.

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Pan Nanofibers And Nanofiber Reinforced Composites, Cheng Ren

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Nanomaterials play an important role in the development of nanotechnology. They possess unique mechanical, physical, and chemical properties coupled with small size and ultrahigh surface area that can provide critical advantages for applications. Continuous nanofibers attract special interest due to their dual nano-macro nature and ability to bridge scales. Nanofibers are being considered for a broad range of applications spanning advanced filters, separation membranes, ultrasensitive sensors, micro/nano actuators, nanoprobes, tissue engineering scaffolds, protective and smart closing, and multifunctional composites. Most of these applications require certain mechanical properties and robustness. However, the literature on the mechanical behavior of nanofibers and their …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources