Other Engineering Science and Materials Commons^™

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

Characteristics Of Carbonaceous Materials Synthesized From Palm Oil Empty Fruit Bunch Waste Using Ferrocene Catalyst, Ahmad Nabil Shahab, Adinda Izzatul Islam, Afif Wardana, Ilham Nur Dimas Yahya, Ary Yanuar Tri Amalia, Nofrijon Sofyan, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The synthesis of carbonaceous materials for reduced graphene oxide (rGO) precursors using oil palm empty fruit bunches waste as a carbon source offers a sustainable solution for waste management in the palm oil industry while delivering high-performance materials. The oil palm empty fruit bunches were carbonized, followed by acid washing, pyrolysis with ferrocene (8%, 12%, and 16% variations), and ultrasonication to produce rGO. The structural, electronic, and morphological properties of the rGO were analyzed using various characterization techniques. The band gap values decreased with increasing ferrocene concentration, from 1.14 eV (8%) to 1.06 (16%), indicating enhanced electronic conductivity. XRD analysis …

Experimental Investigation And Operating Characteristics Of Lhr Engine Using Bio-Fuel Blends With Additives, Suresh R

Theses and Dissertations

The huge energy demand and environmental anxiety are the reasons for the focus on the interest in alternative fuels for diesel engines. This has resulted in a worldwide search for renewable, less pollutant and agricultural-based alternate fuels. Also, attention is given to increasing the efficiency of a conventional diesel engine when operating on alternative fuels. The bio-fuel derived from non-edible oil such as Pongamia oil and Neem seed oil are suggested alternative fuels for this LHR engine.

Diesel engine combustion components viz., the piston crown and liner were coated with Aluminium Titanate thermal barrier coating material. The objective of this …

Usability Analysis Of The Ronnie Baugh (Oggun Ii) Tractor Using The Single Usability Metric [Research Note], John Lester Remot, John Kenneth Punongbayan, Stephanie Caridad Landicho, Alan Marco Mercado, Josefa Angelie Revilla, Omar Zubia

The Philippine Agricultural Scientist

Agricultural mechanization is one of the policies created by the Philippine government to alleviate systemic problems facing the country. In 2020, a local company was licensed to manufacture the American-designed Ronnie Baugh tractor (RBT), which aims to enable smaller-scale production with low-cost and customizable features. This study assessed the usability of the RBT and evaluated the appropriateness of its design for Filipino tractor operators using the single usability metric (SUM). A total of 21 participants were classified according to their age and experience (A – young and experienced, B – old and experienced, and C – young and inexperienced) and …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Development Of Reduced Order Models Using Reservoir Simulation And Physics Informed Machine Learning Techniques, Mark V. Behl Jr

LSU Master's Theses

Reservoir simulation is the industry standard for prediction and characterization of processes in the subsurface. However, simulation is computationally expensive and time consuming. This study explores reduced order models (ROMs) as an appropriate alternative. ROMs that use neural networks effectively capture nonlinear dependencies, and only require available operational data as inputs. Neural networks are a black box and difficult to interpret, however. Physics informed neural networks (PINNs) provide a potential solution to these shortcomings, but have not yet been applied extensively in petroleum engineering.

A mature black-oil simulation model from Volve public data release was used to generate training data …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

Effective Magnetic And Electric Response Of Composite Materials, Mona Hassan Alsaleh

Doctoral Dissertations

Metamaterials (MMs) are nanocomposite materials consisting of metal-dielectric resonators much smaller in size than the wavelength of the incident light. Common examples of metamaterials are based on split ring resonators (SRRs), parallel wires or strips and fishnet structures. These types of materials are designed and fabricated in order to provide unique optical responses to the incident electromagnetic radiation that are not available in naturally existing materials. The MMs can exhibit unusual properties such as strong magnetism at terahertz (THz) and optical frequencies. Additionally, negative index materials (NIMs) can provide negative index of refraction which can be used in many applications …

Structural And Aerodynamic Design, Procedure And Analysis Of A Small V-Shaped Vertical Axis Wind Turbine, Odari J. Whyte

College of Graduate Studies: Theses & Dissertations

Over the last two decades there has been a renewed interest in Vertical Axis Wind Turbines. This turbine configuration though unpopular for large-scale generation has found a niche market in the way of offshore energy harvesting. However, offshore wind has its challenges. In this thesis a detailed comprehensive study of a proposed V-shaped vertical axis turbine rotor is performed in order to examine its structural and aerodynamic characteristics. The design met and exceeded the safety parameters establish for test bed operation, showing a factor of safety of 1.87 with regard to fatigue stress response. A satisfactory fatigue stress design life …

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …

In-Situ Ellipsometry Characterization Of Anodically Grown Silicon Dioxide And Lithium Intercalation Into Silicon, Eric A. Montgomery

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, in-situ ellipsometry and electroanalytical investigations of two electrochemical processes are reported: including the formation of anodically grown silicon dioxide and the intercalation of lithium into silicon. Analysis of the ellipsometry data shows that the anodically grown silicon dioxide layer is uniform and has similar properties as thermally grown silicon dioxide. The lithium-ion intercalation data reveals non-uniform thin film formation, which requires further studies and development of appropriate ellipsometric optical models.

Advisers: Eva Schubert and Mathias Schubert

A Digital Hydraulic Valve, Actuated Using A Piezoelectric Linear Motor, Brian C. Bevill

Purdue Polytechnic Directed Projects

Proportional control in hydraulics is widely utilized. The most widely used current types of proportional valves utilize solenoid technology. While this technology has been around for decades and has been proven an effective means of control, there is always a demand for improved performance of advancing technologies. Integrating piezoelectric devices as a means to control hydraulic systems helps advance control for hydraulic systems.

Piezoelectric stack devices have been used to control hydraulic systems with success. Advantages of these stacks include being relatively small with a high power to weight ratio, using less energy than solenoid operations, and being fast acting. …