Other Engineering Science and Materials Commons^™

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Improving The Concrete Compressive And Flexural Strength With A Low Fraction Addition Of Carboxylated Nitro-Oxidized Cellulose Nanofibrils From Banana Rachis, Ngesa Ezekiel Mushi, Emmanuel Kagya

Tanzania Journal of Science

Conventionally, concrete strength depends on the bonding interface, especially in hydrated products such as calcium silicate hydrate (CSH). As a result, concrete is sensitive to tensile load. With its unique properties, a low fraction of carboxylated nitro-oxidized cellulose nanofibrils (NOCNF) from the banana rachis is employed to improve the mechanical performance of the concrete nanostructurally. Compressive and flexural strength using the NOCNF content at 0, 0.05, and 0.1 wt.%, cured for 7 and 28 days, were evaluated. Notably, the compressive strength increased by 16 % and the flexural strength by 13 % at 0.1 wt.% NOCNF compared to plain concrete …

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Effect Of The Stacking Sequence And Number Of Ply Orientation In A Quasi-Isotropic Laminated Plate On In-Plane Shear Modulus And Failure Modes, Ann Larson

Master's Theses

Maximizing the shear modulus and strength, as well as predicting failure mode and location, when designing a stacking sequence of quasi-isotropic carbon fiber laminated plates is essential to predict stability, resistance to deformation, and overall stiffness of the structure. This research investigates the effect of the stacking sequence of quasi-isotropic laminated composite plate materials in accordance with ASTM D5379: Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method.

In this research, experimental testing and Finite Element Analysis (FEA) were first used on aluminum to validate the simulation process before applying it to composite materials. The …

An Analytical Framework For Quantifying Urban And Community Resilience To Natural Hazards From Cell-Phone Gps-Location And Traffic-Flow Data, Georgios Chatzikyriakidis

Civil and Environmental Engineering Theses and Dissertations

Urban areas are increasingly exposed to natural hazards while accommodating a growing share of the global population, yet a consistent science-based framework for quantifying urban and community resilience remains lacking. This dissertation develops a physics-based analytical framework grounded in statistical mechanics and the quantitative theory of Brownian motion. A city is conceptualized as a complex medium in which citizens move analogously to Brownian particles within a viscoelastic environment, influenced by socioeconomic interactions and infrastructure functionality.

A central premise is that urban resilience, interpreted as engineering resilience (an outcome), can be quantified through a single metric: the mean-square displacement MSD=⟨r²(t)⟩, of …

Development Of Stronger, More Extrudable 6xxx Series Alloys For Automotive Applications, Eli A. Harma

Dissertations, Master's Theses and Master's Reports

6xxx alloys are widely used in automotive extrusion structures for their high specific strength and formability. Advanced designs require greater formability and strength, creating an opportunity for high-strength, formable alloys. The 6xxx series forms β”-Mg₅Si₆ precipitates during age hardening and develops a fibrous microstructure during extrusion, both strengthening the alloy. Increasing Mg and Si to form more β” decreases formability. Thus, modifying texture can increase strength without reducing formability. Current alloys like 6005A add Mn and Cr to form dispersoids that inhibit recrystallization and promote strengthening textures; however, high Mn and Cr concentrations reduce formability. Replacing Mn …

Understanding The Metallic And Oxide Phases In Platinum-Based Bimetallic Heterogeneous Catalysts After High-Temperature Oxidation, Stephen John Porter Jr

Nanoscience and Microsystems ETDs

Platinum (Pt) and palladium (Pd) are critical components in diesel emission control systems, enabling the conversion of harmful pollutants under demanding conditions. However, Pt’s effectiveness is hindered by sintering under high-temperature oxidizing environments. This dissertation investigates how Pt and Pd evolve under oxidizing conditions at 800°C, highlighting their distinct thermodynamic behaviors and interactions. Using TEM, EDS, EELS, XRF, XRD, and EXAFS, we show that Pd suppresses Pt sintering by reducing the volatility of PtO₂, leading to the formation of stable particles. Both Pt and Pd are present in metallic and oxide states, forming biphasic 'Janus' particles with conjoined metal and …

Thermal Modeling Techniques For Additively Manufactured Porous Metals, Lucas D. Rambo

Master's Theses

Advances in additive manufacturing have enabled the creation of metallic components with tailored porosity, offering design flexibility for thermal, structural, and fluid transport applications. This thesis investigates the effective thermal conductivity (ETC) of porous Inconel 625 (IN625) and Inconel-ceramic composites (IN625-RAM2) fabricated by Laser Powder Bed Fusion (LPBF) using Elementum 3D’s PermiAM technology. Experimental measurements of thermal conductivity using the laser flash method are compared to numerical models built from micro-computed tomography data. Simulations were performed using both finite element (FE) and finite volume (FV) methods to evaluate thermal transport in real microstructures. The study investigates the effects of micro- …

Characteristics Of Carbonaceous Materials Synthesized From Palm Oil Empty Fruit Bunch Waste Using Ferrocene Catalyst, Ahmad Nabil Shahab, Adinda Izzatul Islam, Afif Wardana, Ilham Nur Dimas Yahya, Ary Yanuar Tri Amalia, Nofrijon Sofyan, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The synthesis of carbonaceous materials for reduced graphene oxide (rGO) precursors using oil palm empty fruit bunches waste as a carbon source offers a sustainable solution for waste management in the palm oil industry while delivering high-performance materials. The oil palm empty fruit bunches were carbonized, followed by acid washing, pyrolysis with ferrocene (8%, 12%, and 16% variations), and ultrasonication to produce rGO. The structural, electronic, and morphological properties of the rGO were analyzed using various characterization techniques. The band gap values decreased with increasing ferrocene concentration, from 1.14 eV (8%) to 1.06 (16%), indicating enhanced electronic conductivity. XRD analysis …

Microwave-Assisted Reduction Of Critical Metal Oxides From E-Waste Mixture, Kurundu Shavinka Jayasekera

Graduate Theses, Dissertations, and Problem Reports (ETD)

The efficient recovery of critical metals such as tantalum (Ta), manganese (Mn), gallium (Ga), and indium (In) from electronic waste (e-waste) is essential for resource sustainability and environmental protection. This research uses microwave-assisted treatment to investigate the carbothermal reduction of these four specific metals from their oxides in a simulated e-waste mixture, with carbon black serving as both a microwave coupling and reduction agent. Microwave processing is used specifically because it offers a rapid and energy-efficient alternative to conventional thermal methods, with the benefits of intrinsic heating and selective heating of materials. The first experiments centered on understanding the effects …

Effects Of Soil Properties On Cp Performance, Cecilia Segretario

Williams Honors College, Honors Research Projects

This research aims to evaluate the affect of various soil properties on the effectiveness of cathodic protection (CP) in preventing underground pipeline corrosion. Metal coupons of common pipeline materials with applied CP will be mounted in several separate controlled soil environments to manipulate real world underground corrosion scenarios. Each soil environment will have different physical properties by mixing the soil with a prepared chemical solution. The physical properties to be evaluated include pH, resistivity, and moisture content. At the end of a corrosion duration, weight loss method will be used to evaluate the corrosion rate over that period. Additionally, the …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

Development Of Machine Learning-Based Tool For Prediction Of Long-Term Field Performance Of Asphalt Concrete Overlays In A Hot And Humid Climate, Elise Mansour

LSU Doctoral Dissertations

The performance of pavement plays a critical role in Maintenance, Rehabilitation and Reconstruction (MR&R) for highway agencies. Reliable and accurate estimation of pavement performance can be instrumental in prioritization of the limited resources and funding for highway agencies. The latter requires robust prediction models that can handle large-scale, real-world data and can forecast pavement performance in the long run. Unfortunately, the traditional performance prediction models have raised concerns regarding their efficiency and accuracy. It is because these models were based on a limited number of explanatory variables, were not up-to-date and were designed for forecasting short-term (up to five years) …

Biocorrosion Analysis Via Multiscale Time Series Analysis, Victor Hugo Mendoza Vejar, Eliseo Hernandez Martinez, Hector Puebla

Annual Symposium on Biomathematics and Ecology Education and Research

No abstract provided.

Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb

Theses and Dissertations

Implantable drug delivery devices have many benefits over traditional drug administration techniques and have attracted a lot of attention in recent years. By delivering the medication directly to the tissue, they enable the use of larger localized concentrations, enhancing the efficacy of the treatment. Passive-release drug delivery systems, one of the various ways to provide medication, are great inventions. However, they cannot dispense the medication on demand since they are nonprogrammable. Therefore, active actuators are more advantageous in delivery applications. Smart material actuators, however, have greatly increased in popularity for manufacturing wearable and implantable micropumps due to their high energy …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Integrating Steel Slag Aggregates Into Asphalt Paving By Harmonizing Availability, Quality, Economics, And The Environment, Timothy R. Murphy

Theses and Dissertations

This thesis provides guidance on how to balance matters related to the environmental stewardship, market sources, origin and uses, material properties, performance, and economic impact of using slag materials in pavements. The literature on this topic provides numerous references on the use of slag materials for specific applications, and this thesis aims to make use of those references along with other data from the author to describe slag materials from a holistic perspective and provide some suggestions for balancing several factors that impact optimal use of this resource within pavement structures. Discussion is given to the increased importance of recycling …

Soil Respiration Measurements Reveal High Retention Of Organic Carbon From Corn Residue Derived High-Lignin Fermentation Byproduct Enabling Sustainable Lignocellulosic Biofuel Production, Michelle Sun Wang

Dartmouth College Master’s Theses

While 2G biofuel production can utilize non-edible, lignocellulosic feedstocks such as agricultural residues to produce liquid fuel, harvesting crop residues is unsustainable without careful management of the soil underneath. By harvesting a fraction of the crop residues left in the field after harvest, soil health can diminish and critically, the soil organic carbon (SOC) stored in agricultural fields can decrease. Currently, in the most popular 2G process models published, the issue of soil degradation remains unresolved with residue harvest strategies receiving considerable attention in the literature and other SOC management strategies receiving far less. Specifically, the strategy of returning the …

Machinability Of High Mn Steel Using Tool Life Criteria, Dika Handayani, Victor F. Okhuysen, Nicole Wagner

Engineering Faculty Articles and Research

High Mn steel alloys have shown to provide both high strength and ductility. However, current literature offers limited guidance on the machinability of these steel alloys. Therefore, this work provides turning recommendations for high Mn steel that is based on tool life data. Several indexable carbide inserts with various rake angles were used to machine cast billets of high Mn steel. Turning characteristics from various feed rates, cutting speeds, and depths of cut were analyzed. Through a design of experiments, it was determined that the feed rate was the most significant factor affecting tool life and that a tool with …

Assessing A Byproduct Of The Cbd Ethanol Extraction Process For Potential As A Wood Finishing Product, Avani M. Flanagan

Masters Theses

Developments in regulations concerning the use of CBD products as therapeutic remedies have allowed the global cannabidiol (CBD) market to take off within the past five years. Despite producers of CBD oil wanting to optimize their methods and increase product yields, several waste streams still exist. During the winterization phase of the ethanol extraction process, CBD oil is cooled and filtered so the fats, waxes, and lipids from the Cannabis sativa plant can coagulate and be removed, creating a purer oil with higher potency but contributing to the 58% (crude weight) total loss that occurs throughout the process. The removed …

Understanding The Feasibility Of Improving Interfacial Properties In Direct Ink Writing Of Silicone-Polyurethane Resin Hybrid Material, Ayobami Samuel Akinfenwa

College of Graduate Studies: Theses & Dissertations

The progress in materials engineering and the ability to make various models possible have made soft robotics a popular alternative to traditional robotics. Still, soft robots need various parts, like Printed Circuit Boards (PCBs), batteries, cables, fittings, and more, to work correctly or to get attached to other complex parts. These parts can have different material properties, like elastic moduli, strength, etc. Because of these differences, mechanical failures happen at the points where two materials meet, making soft robots less durable and less lasting in real-life situations due to failure. Conventionally, the fabrication of soft robot parts is through moulding. …

Development Of Inconel 718f And Inconel 718e Powders For Parts Manufacturing Utilizing Binder Jet Three-Dimensional Printing And Compressed Pellet Methods, Duncan Eric Manor Ii

Graduate Theses, Dissertations, and Problem Reports (ETD)

Alloy Inconel 718 is a Ni based superalloy used for high temperature applications including turbine blades, turbocharger rotors and nuclear reactors. Inconel 718 is a popular commercial atomized powder that has limitations in performance for use in additive manufacturing applications due to poor part quality and efficiency of current fabrication methods. Developing new compositions and additive manufacturing (AM) methodologies of IN718 is critical to improve the quality and the efficiency of IN718 parts manufacturing. Developing new additive manufacturing methodology that produces higher quality parts made of IN718 as compared to current methods has the potential to greatly impact industry, academia, …

Fem Eem Dataset: Optimising Retrofitted Insulation For Irish Residential Building Walls, Rakshit D. Muddu, Aimee Byrne, Anthony Robinson Dr.

Datasets

A large number of combinations of Irish wall types, insulation materials, and heating fuel types were produced to compare the multiple variables which influence Optimal Insulation Thickness values. The total cost (TC) and carbon emission (CE) at optimum insulation thickness (OIT) for all combinations of insulation material and three types of fuel are considered. The dataset presents OIT for solid wall, cavity wall and cavity block wall types located in Monaghan, Dublin, and Kerry.

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

In-Situ Defect Detection Using Acoustic Vibration Monitoring For Additive Manufacturing Processes, Ali Harake

Master's Theses

The world of additive manufacturing revolves around speed and repeatability. Inherently, the process of 3D printing is plagued with variability that fluctuates with every material and parameter modification. Without proper qualification standards, processes can never become stable enough to produce parts that may be used in aerospace, medical, and construction industries. These industries rely on high quality metrics in order to protect the lives of those who may benefit from them. To establish trust in a process, all points of variation must be controlled and accounted for every part produced. In instances where even the best process controls are enacted, …

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

LSU New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Detection And Identification Of Disturbances By Spectral Analysis Of Structure-Borne Noise During The Production Of A Sealing Seam, Felix Kruppa, Lars Meisenbach, Berend Oberdorfer Dr.-Ing., Bernd Wilke Prof. Dr.-Ing.

Journal of Applied Packaging Research

When sealing, disturbances or errors can occur that impair the quality of the sealing seam and, in the worst case, lead to leaks. It is therefore important to identify and eliminate defective packages during production and to minimize the elimination by readjusting machine parameters. The aim of this article is the clear identification of seam quality problems on a vertical forming, filling and sealing machine SVE2520 by evaluating process parameters during the manufacturing process. For this purpose, the structure-borne noise is measured for each seal in order to identify not-usual curves. These not-usual curves are related to different disturbances or …