Other Engineering Science and Materials Commons^™

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Molybdenum-Doped Zinc Oxide Nanocomposite For Sustainable Photoelectrocatalytic Degradation Of Dyes And Antimicrobial Activity, Samar A. Salim

Nanotechnology Research Centre

Mo-doped ZnO nanocomposite was synthesized by using auto-combustion method. X-ray diffraction patterns of prepared nanocomposite indicated effective construction of crystalline Mo/ZnO NCs with co-existence of MoO2 and ZnO in required weight ratio. XRD results revealed also that ZnO crystallite size decreased as Mo-doping concentration increased. The direct band gap reduced from 3.309 eV of (MZ-0) to 3.258 eV of (MZ-5), demonstrating a negative correlation with Mo-doping levels. The electrocatalytic activity of Mo/ZnO NCs was assessed by their capability to degrade Indigo Carmine (IC) and Murexide (ME) dyes, and their antibacterial properties were also evaluated. The electrocatalytic (EC) degradation efficiencies for …

Detecting Electrical Submersible Pump (Esp) Failures And Estimating Run Life Using Artificial Neural Networks, Mostafa Ahmed Sobhy

Theses and Dissertations

Electric Submersible Pumps (ESPs) are one of the important artificial lift methods for sustaining production in mature and high-water-cut wells; but may suffer frequent failures due to mechanical, electrical, hydraulic, chemical, and operational failures. These failures can yield substantial deferred production and intervention costs. Plenty of ESP installations are fitted with downhole sensors. Yet, it is observed that the current industry practice underutilizes the wealth of available sensor and operational data and lacks standardized, explainable failure-type identification and classification.

In this thesis, a comprehensive Machine Learning (ML) and Deep Learning (DL) framework was introduced for ESPs that simultaneously estimates remaining …

Thermophysical Properties Of Aqueous Amine Salts For Closed Air Cabin Revitalization, Mahmud R. Yusuf, Isabela Flores, Ben Hines, Li Hua Zhang, Seth Christa, Brooks D. Rabideau, Kevin West, Breanna Dobyns, James Davis

Shelby Hall Graduate Research Forum Posters

Carbon dioxide (CO2) capture plays a crucial role in closed cabin air revitalization, however current CO2 capture technologies pose several issues. Traditional amine solutions, such as monoethanolamine, are commonly used in CO2 capture on the International Space Station but face drawbacks including high volatility, thermal degradation, and unpleasant odor. To overcome these challenges, amine salt solutions have emerged as promising alternatives. Amine salt solutions have reduced environmental impact, lower corrosion potential, and improved CO2 loading capacity, making them a more efficient and sustainable replacement. Knowing these physical properties are critical for modeling and optimizing a scrubbing process that employs these …

Microwave-Assisted Reduction Of Critical Metal Oxides From E-Waste Mixture, Kurundu Shavinka Jayasekera

Graduate Theses, Dissertations, and Problem Reports (ETD)

The efficient recovery of critical metals such as tantalum (Ta), manganese (Mn), gallium (Ga), and indium (In) from electronic waste (e-waste) is essential for resource sustainability and environmental protection. This research uses microwave-assisted treatment to investigate the carbothermal reduction of these four specific metals from their oxides in a simulated e-waste mixture, with carbon black serving as both a microwave coupling and reduction agent. Microwave processing is used specifically because it offers a rapid and energy-efficient alternative to conventional thermal methods, with the benefits of intrinsic heating and selective heating of materials. The first experiments centered on understanding the effects …

Effects Of Soil Properties On Cp Performance, Cecilia Segretario

Williams Honors College, Honors Research Projects

This research aims to evaluate the affect of various soil properties on the effectiveness of cathodic protection (CP) in preventing underground pipeline corrosion. Metal coupons of common pipeline materials with applied CP will be mounted in several separate controlled soil environments to manipulate real world underground corrosion scenarios. Each soil environment will have different physical properties by mixing the soil with a prepared chemical solution. The physical properties to be evaluated include pH, resistivity, and moisture content. At the end of a corrosion duration, weight loss method will be used to evaluate the corrosion rate over that period. Additionally, the …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

Improving Static Cold Storage Life Of The Human Heart Before Transplant, Juan Sebastian Rodriguez Paez

Theses and Dissertations

Organ storage and transportation are critical steps for the success of organ transplantation. Static cold storage (SCS) of hearts for heart transplantation (HTx) remains the standard approach. However, SCS may involve damage to the tissue resulting from extended hypothermic preservation, potentially affecting organ viability. More over, the temperature distribution on and within the heart is unknown during heart transplantation. Therefore, there is an interest to study different stages of the heart transplantation process towards determining the 3D temperature distribution on and within the heart. There could be a possibility of having a hypothermic injury in different parts of the heart …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Robust Gasification Trial Results For A Variety Of Difficult-To-Recycle Packaging-Related Materials, Bruce A. Welt

Journal of Applied Packaging Research

Currently, recycling requires nearly absolute sorting of materials to accommodate the limited capabilities of existing recycling infrastructure. Whether a material is “recyclable” depends more on the method of recycling than the material itself. Our dependence upon sorting has limited success of recycling and has stifled our ability to achieve circular economy sustainability with plastic packaging materials. Our dependence upon sorting is rooted in our material-specific recycling processes. However, newer robust recycling processes are commercially available that reduce or eliminate the need to sort waste, and can convert mixed waste into primary feedstock chemicals, such as methanol for subsequent manufacture of …

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Valorization Of Xylan In Agroforestry Waste Streams, Harrison Appiah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Valorization of Xylan in Agroforestry Waste Streams.

Harrison Appiah

Microwave-assisted deep eutectic solvent and gamma-valerolactone metallic chloride catalyzed conversion of xylan to furfural were investigated using a 2x3 factorial experimental design at two levels of percent microwave power, reaction time, and catalyst concentration. The levels of each factor studied were (20%, 60% microwave power, 2, 4 minutes, and 10, 20mg) respectively. The effect of three metallic chloride catalysts (LiCl, FeCl3.6H20, CuCl2) on the conversion of xylan to furfural was also investigated. The gamma-valerolactone-ferric chloride sent system exhibited the highest mean yield of furfural (56.50%). The next highest furfural yield of …

Dry Reforming Of Methane Using Microwave Irradiated Metal Oxide/Coal Char Catalysts, Anthony Carter

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research focuses on the synthesis of both shaped and amorphous powder materials, the combination of these materials with dried Powder River Basin (PRB) coal char, and their reactionary properties with methane and carbon dioxide gasses with conventional and microwave (MW) heating. The first goal of this project was to synthesize shaped micro and nano sized particles with ideal dielectric properties for converting electromagnetic energy into heat and proven capabilities of activating methane. These particles were synthesized via solvothermal, hydrothermal, and co-preceptory treatments alone and onto the surface of dried PRB coal char. PRB is a sub-bituminous, low-ranking coal (LRC) …

Engineering Of Earth-Abundant Electrochemical Catalysts, Dylan D. Rodene

Theses and Dissertations

Alternative energy research into hydrogen production via water electrolysis addresses environmental and sustainability concerns associated with fossil fuel use. Renewable-powered electrolyzers are foreseen to produce hydrogen if energy and cost requirements are achieved. Electrocatalysts reduce the energy requirements of operating electrolyzers by lowering the reaction kinetics at the electrodes. Platinum group metals (PGMs) tend to be utilized as electrocatalysts but are not readily available and are expensive. Ni_1-xMo_x alloys, as low-cost and earth-abundant transition metal nanoparticles (NPs), are emerging as promising electrocatalyst candidates to replace expensive PGM catalysts in alkaline media. Pure-phase cubic and hexagonal Ni_{1-x …}

Nanoflower-Like Bi2moo6/Ag3po4 In Water Treatment, Xavier Morgan-Lange, Jaeyun Moon, Kaleab Ayalew

McNair Poster Presentations

• Environmental issues continue to intensify causing natural resources such as clean water to become increasingly scarce while demand only continues to grow. • Some of the most effective measures taken appear to be bioremediation tactics and their synthetic counterparts. • A critical area of interest are semi-conducting photocatalytic nanomaterials that take advantage of the photo-electric effect and use the introduction of ultra violet (UV) and visible light to induce oxidation and reduction reaction in p-type semiconductors. This results in the decomposition of certain pollutants and/or deactivates certain microbes in water. • These materials have the potential to operate using …

Influence Of Substrate Stage Temperature And Rotation Rate On The Magneto-Optical Quality Of Rf-Sputtered Bi2.1dy0.9fe3.9ga1.1o12 Garnet Thin Films, Mohammad E. Alam, Mikhail Vasiliev, Kamal Alameh

Research outputs 2014 to 2021

Highly bismuth-substituted iron garnet thin films are prepared on quartz substrates by using a radio frequency (RF) magnetron sputtering technique. We study the factors (process parameters associated with the RF magnetron sputter deposition technique) affecting the magneto-optical (MO) properties of ferrite garnet films of composition Bi2.1Dy0.9Fe3.9Ga1.1O12. All films show high MO response across the visible range of wavelengths after being annealed. In particular, the effects of substrate stage temperature and rotation rate on the various properties of films are studied. Experimental results reveal that the characteristics of garnet films of this type can be tuned and optimized for use in …

Data Driven Discovery Of Materials Properties., Fadoua Khmaissia

Electronic Theses and Dissertations

The high pace of nowadays industrial evolution is creating an urgent need to design new cost efficient materials that can satisfy both current and future demands. However, with the increase of structural and functional complexity of materials, the ability to rationally design new materials with a precise set of properties has become increasingly challenging. This basic observation has triggered the idea of applying machine learning techniques in the field, which was further encouraged by the launch of the Materials Genome Initiative (MGI) by the US government since 2011. In this work, we present a novel approach to apply machine learning …

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …

Cement Based Batteries And Their Potential For Use In Low Power Operations, Aimee Byrne, Niall Holmes, Brian Norton

Articles

This paper presents the development of an innovative cement-electrolyte battery for low power operations such as cathodic protection of reinforced concrete. A battery design was refined by altering different constituents and examining the open circuit voltage, resistor loaded current and lifespan. The final design consisted of a copper plate cathode, aluminium plate anode, and a cement electrolyte which included additives of carbon black, plasticiser, Alum salt and Epsom salt. A relationship between age, temperature and hydration of the cell and the current it produced was determined. It was found that sealing the battery using varnish increased the moisture retention and …

An Overview Of The Development Of Cement-Based Batteries For The Cathodic Protection Of Embedded Steel In Concrete, Aimee Byrne, Niall Holmes, Brian Norton

Conference papers

This paper presents an overview of the cement-based batteries developed in DIT for use in the cathodic protection of embedded steel in reinforced concrete undergoing chloride-induced corrosion. Cathodic protection delivers an external current (approximately 20mA per m2 of embedded steel) which effectively polarises the internal current generated during corrosion. The batteries developed in DIT comprise of a cement-based electrolyte containing different additives including sand, aggregate, salts, carbon black and plasticiser with protruding anode and cathode metal plates. These batteries produced an initial electrical output of 1.5V and 23mA through a 10 resistor as measured using data acquisition units and a …

Elevated Test Pressure Significantly Reduces Dynamic Accumulation Oxygen Transmission Rate (Astm F3136) Measurement Time For Barrier Packaging Films, Bruce A. Welt

Journal of Applied Packaging Research

Measurement of gas transmission rates of materials is important for successful package design. The dynamic accumulation (DA) method (ASTM F3136) is becoming increasingly popular for measuring oxygen transmission rate (OTR) due to its simplicity and low cost. However, measurement time increases with barrier properties of materials, limiting measurement throughput. A dynamic accumulation measurement prototype capable of operating up to 1,000 psig was developed in order to accelerate gas transfer by boosting concentration gradients via elevated absolute pressures. Results show that measurement results were independent of test pressure while measurement times were substantially reduced. These results also suggest that gas transmission …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

A Study Of The Flow Characteristics In The Core Region Of The Sandia Engineering Reactor, James A. Moeller

Chemical and Biological Engineering ETDs

The core region of a nuclear rector is an extremely compact area with a capability of providing a very high heat output. Regardless of the type of coolant used, the heat transfer characteristics of this region must be adequately designed to prevent any undesirable "hot-spots" from developing. The Sandia Engineering Reactor has one of the most compact cores of any in currently operating nuclear reactors. For this reason it is necessary to investigate fully the heat transfer characteristics of the core. The rate of heat transfer from the fuel elements to the coolant is directly dependent upon the temperature difference …