Engineering Mechanics Commons^™

Me-Em Enewsbrief, December 2012, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Implementation Of Magnetic Resonance Elastography For The Investigation Of Traumatic Brain Injuries, Thomas Boulet

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Magnetic resonance elastography (MRE) is a potentially transformative imaging modality allowing local and non-invasive measurement of biological tissue mechanical properties. It uses a specific phase contrast MR pulse sequence to measure induced vibratory motion in soft material, from which material properties can be estimated. Compared to other imaging techniques, MRE is able to detect tissue pathology at early stages by quantifying the changes in tissue stiffness associated with diseases. In an effort to develop the technique and improve its capabilities, two inversion algorithms were written to evaluate viscoelastic properties from the measured displacements fields. The first one was based on …

Vibrations Of Crystal Plates With Surface Structures For Resonator And Sensor Applications, Nan Liu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

This dissertation is mainly on the theoretical analysis of vibrating crystal plates for acoustic wave resonator and sensor applications. The frequency and mode effects of different surface structures on either or both sides of the crystal plates are the main concerns in this dissertation. These effects are fundamental to the improvement of existing acoustic wave devices, or to the design of new acoustic wave devices, especially new sensors based on these effects.

At first, two-dimensional equations of motion for an anisotropic crystal plate with two thin films on its surfaces are derived by reduction from the three-dimensional equations of anisotropic …

Steering Adaptation In A Driving Simulator, Brian P. Moran

Undergraduate Research Posters 2012

Steering adaptation in a driving simulator occurs when participants, who possess the skills necessary to control a vehicle, modify their use of the steering controls to successfully interact with a driving simulator. This approach is sensitive to individual driving styles, as it is free of any threshold, criterion, or benchmark value and can be applied to any steering task at any driving speed.

Me-Em Enewsbrief, September 2012, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

A Resistance Based Structural Health Monitoring System For Composite Structure Applications, Dennis N. Boettcher

Master's Theses

This research effort explored the possibility of using interwoven conductive and nonconductive fibers in a composite laminate for structural health monitoring (SHM). Traditional SHM systems utilize fiber optics, piezoelectrics, or detect defects by nondestructive test methods by use of sonar graphs or x-rays. However, these approaches are often expensive, time consuming and complicated.

The primary objective of this research was to apply a resistance based method of structural health monitoring to a composite structure to determine structural integrity and presence of defects.

The conductive properties of fiber such as carbon, copper, or constantan - a copper-nickel alloy - can be …

Propagation Of Ultrasound Through Freshly Excised Human Calvarium, Armando Garcia Noguera

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The propagation of ultrasound through complex biological media, such as the human calvarium, poses a great challenge for modern medicine. Several ultrasonic techniques commonly used for treatment and diagnosis in most of the human body are still difficult to apply to the human brain, in part, because of the properties of the skull. Moreover, an understanding of the biomechanics of transcranial ultrasound may provide needed insight into the problem of blast wave induced traumatic brain injury (TBI). In the present study, the spatial variability of ultrasonic properties was evaluated for relevant frequencies of 0.5, 1, and 2.25 MHz. A total …

Me-Em Enewsbrief, June 2012, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Finite Element Modeling Of Ballistic Impact On A Glass Fiber Composite Armor, Dan M. Davis

Master's Theses

Finite Element Modeling of Ballistic Impact on a Glass Fiber Composite Armor

Dan Davis

Experiments measuring the ballistic performance of a commercially available fiberglass armor plate were used to guide the development of constitutive laws for a finite element model of the impact. The test samples are commercially available armor panels, made from E-glass fiber reinforced polyester rated to NIJ level III. Quasi-static tensile tests were used to establish material properties of the test panels. These properties were then used to create models in the explicit finite element code LSDYNA.

Ballistic impact testing of the panels was conducted using a …

Shock And Vibration Isolation System For Ambulatory And Litter Patients In Ground And Air Medical Transport, Mohamad R. Hachem

UNLV Theses, Dissertations, Professional Papers, and Capstones

This project explored the effectiveness of seat and litter air bladder technologies in reducing patient exposure to whole body shock and vibration during ground borne and airborne medical transport. Several seat and litter air bladder configurations were examined during field tests in a U.S. Army RG-33 MRAP ambulance and a U.S. Army HH-60M Black Hawk helicopter. The MRAP field tests were conducted at Ft. Detrick, Maryland. The Black Hawk field tests were conducted at Ft. Rucker, Alabama.

During the field tests, tri-axial vibration signals were recorded on a 16-channel CoCo90 Data Logger/Frequency Analyzer and then post processed in the laboratory …

Me-Em Enewsbrief, March 2012, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …