Engineering Mechanics Commons^™

The Effects Of Bending On The Strain Distributions In A Stiffener-Skin Interface Region, Osvaldo F. Lopez

Mechanical & Aerospace Engineering Theses & Dissertations

An analytical and experimental study to assess the effect of bending on the adhesive strain distributions in a stiffener-skin interface region is described. A one-dimensional beam analysis is derived using a variational approach. Parametric studies are conducted to assess the effects of stiffener, skin, and adhesive thickness and adhesive material nonlinearity on the adhesive layer extensional and shear strain distributions subjected to applied bending. Two experimental methods of measuring through-the-thickness extensional strains in an adhesive are investigated. One method involves measuring the changes in the resistance of a composite strain sensor subjected to applied tension and compression loads. The second …

Application Of Shape Sensitivity Analysis For Computation Of Transient Free-Surface Flows, Frank Nicolas Michel

Mechanical & Aerospace Engineering Theses & Dissertations

Shape sensitivity analysis is introduced into a numerical scheme simulating a transient free-surface flow and applied to the case of a fluid advancing through a bed of cylinders. For this incompressible Newtonian flow, viscous forces are dominant. A penalty function finite element formulation is used to solve the problem. Coordinates of nodes on the moving boundary are chosen as design variables and an analytical formulation of the gradient of the finite element algebraic system, with respect to these variables, is derived.

In a numerical example, the results obtained with and without sensitivity analysis are compared. The efficiency and accuracy of …

Determinations Of Molecular Weight And Molecular Weight Distribution Of High Polymers By The Rheological Properties, Joan Y. Z. Huang

Mechanical & Aerospace Engineering Theses & Dissertations

Several methods are reviewed by which the molecular weight (MW) and molecular weight distribution (MWD) of polymeric material were determined from the rheological properties. A poly (arylene ether) polymer with six different molecular weights was used in this investigation. Experimentally measured MW and MWD were conducted by GPC/LALLS (Gel Permeation Chromatography/Low Angle Laser Light Scattering), and the rheological properties of the melts were measured by a Rheometric System Four rheometer. It was found that qualitative information of the MW and MWD of these polymers could be derived from the viscoelastic properties, with the methods proposed by Zeichner and Pate1, and …

Stability Design Of A Slender Column With Curved Longitudinal Stiffeners, Mark S. Lake

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents the results of a stability design study of a slender column with curved longitudinal stiffeners for large space structure applications. The stiffened column concept is attractive because it allows the buckling load of a slender column to be increased at a fairly low cost in increased mass, and at no change in the column packaged size. Linear stability analyses are performed using a "linked-plate" representation of the stiffeners to determine stiffener local buckling stresses. Results from a set of parametric analyses are used to determine an approximate explicit expression for stiffener local buckling in terms of its …

Global/Local Stress Analysis Of Composite Structures, Jonathan B. Ransom

Mechanical & Aerospace Engineering Theses & Dissertations

A method for performing a global/local stress analysis is described and its capabilities are demonstrated. The method employs spline interpolation functions which satisfy the linear plate bending equation to determine displacements and rotations from a global model which are used as "boundary conditions" for the local model. Then, the local model is analyzed independent of the global model of the structure. This approach can be used to determine local, detailed stress states for specific structural regions using independent, refined local models which exploit information from less-refined global models. The method presented is not restricted to having a priori knowledge of …

Investigating The Method Of Structural Topological Variations For Sensitivity Analysis And Design Optimization, Niki A. Mehta

Mechanical & Aerospace Engineering Theses & Dissertations

The method of structural topological variations is a newly developed technique for analysis of frame structures. It provides a novel method that completely avoids formulating and solving simultaneous equations, required in the finite element displacement method. The principal objective of this thesis is to investigate the method of topological variations as a possible design tool and study its applicability in the sensitivity analysis and in the process of design optimization.

A computer code was developed for this method to obtain its comparative performance against the finite element displacement method. For analysis of large structures involving frequent local modifications, the method …

Explicit And Implicit Calculations Of Turbulent Cavity Flows With And Without Yaw Angle, Guan-Wei Yen

Mechanical & Aerospace Engineering Theses & Dissertations

Computations have been performed to simulate turbulent supersonic flows past three-dimensional deep cavities with and without yaw. Simulation of these self-sustained oscillatory flows have been generated through time accurate solutions of the Reynolds averaged complete Navier-Stokes equations using two different schemes: (1) MacCormack, finite-difference, (2) implicit, upwind, finite-volume schemes. The second scheme, which is approximately 30% faster, is found to produce better time accurate results. The Reynolds stresses have been modeled, using the Baldwin-Lomax algebraic turbulence model with certain modifications. The computational results include instantaneous and time averaged flow properties everywhere in the computational domain. Time series analyses have been …

Simulation Of Fluid Flow In Packed Beds Using A Simplified Model And Network Analysis Technique, Haggai W.K. Sarakikya

Tanzania Journal of Engineering and Technology (TJET)

Abstract

A Reiner-Rivlin Fluid Flow Through Entrance Region Of A Circular Pipe, V. G. Masanja

Tanzania Journal of Engineering and Technology (TJET)

The flow of a Reiner-Rivlin fluid with two viscosity coefficients through the entrance region of a circular pipe has been studied numerically. In particular the growth of the entrance length as a function of the Reynolds number and the non-Newtonian parameters has been examined. Where comparison could be made, the results have been compared with existing experimental -and numerical data as well as the limited theoretical work available.

Expert Systems For Automated Maintenance Of A Mars Oxygen Production System, Ming-Tsang Ho

Mechanical & Aerospace Engineering Theses & Dissertations

A prototype expert system has been developed for maintaining autonomous operation of a Mars oxygen production system. Normal operation conditions and failure modes according to certain desired criteria are tested and identified. Several schemes for failure detection and isolation using forward chaining, backward chaining, knowledge-based and rule-based are devised to perform several housekeeping functions. These functions include self-health checkout, an emergency shut down program, fault detection and conventional control activities. An effort has been made to derive the dynamic model of the system using Bond-Graph technique in order to develop the model-based failure detection and isolation scheme by estimation method. …

The Effects Of Nonlinearities On The Optimal Design Of Forced Vibrating Beams, Cheryl Celestine Jackson

Mechanical & Aerospace Engineering Theses & Dissertations

The optimal design of a beam under harmonic excitations is formulated and solved numerically for linear and nonlinear forced vibration theories. The beam has a nonuniform cross-sect ion, whose thickness can change during the optimization procedure. Based on the numerical results, for the given input frequency range, the linear vibration theory produces a more conservative design than the nonlinear vibration theory.

The analytical formulation for both theories is presented. For the linear case, a mean case is defined for the self-weight on a beam, and an alternating case is defined for input forcing frequencies which cause fatigue variations on a …