Engineering Mechanics Commons^™

Magnetic Field-Induced Transformation In Polycrystalline Ni2mnal Heusler Type Magnetic Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The martensitic and magnetic transformations, as well as the mechanical properties, of Ni₂MnAl alloys in as-cast (AC) and heat-treated (HT) conditions were investigated. Magnetic-field-induced strain was evaluated via magnetostriction, with reversible strains of 0.14% and 0.2% achieved in the martensitic phase at 2 K for the AC and HT alloys, respectively. Transformation temperatures and Curie temperatures were determined under constant applied magnetic field, revealing that γ-phase inclusions in the AC microstructure suppress antiferromagnetic domain response, yielding a lower magnetization (∼8.4 emu g⁻¹) compared to the HT alloy (∼13.4 emu g⁻¹). Both alloys exhibited hysteretic behavior in the martensitic state and …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. The end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …

Electrochemical Deposition In Energy Storage Devices, Witness Atutala Martin

Graduate Theses and Dissertations

Metals, whether in a solid or soluble ion form, are a vital part of any electrochemical storage system. More so, Li metal is widely considered as the ideal anode because of its low density and low electrochemical potential (-3.04 V vs. the standard hydrogen electrode – SHE). However, just like most metals, it does not plate or strip evenly during cycling which can lead to cycling performance issues, short cycling lifespans, and even safety concerns brought about by dendrites that can cause internal short-circuiting within cells. This research focused on investigating the electroplating of metals in both aqueous and non-aqueous …

Spherical Cavity Expansion Approach For The Study Of Rigid-Penetrator’S Impact Problems, Mario Buchely, Alejandro Marañon

Materials Science and Engineering Faculty Research & Creative Works

In recent years, Spherical Cavity Expansion (SCE) theory has been extensively utilized to model dynamic deformation processes related to indentation and penetration problems in many fields. In this review, the SCE theory is introduced by explaining the different mathematical features of this theory, its solution, and a potential application to model the penetration of a rigid penetrator into a deformable target. First, a chronologically literature review of the most common models used to study this kind of penetration problems is introduced, focusing on the SCE theory. Then, the engineering model of penetration is presented using the SCE approach. The model …

Tensile Specimen Punch, John Allen

All Undergraduate Projects

This project comes from a need to have tensile specimens made for the MET 351, Metallurgy/Materials and Processes, and 426, Applied Strengths of Materials, labs. This punch is designed to be used with an arbor press to create the desired tensile specimen shape out of plastic blanks. The initial concept was suggested by Dr. Craig Johnson. The designs went through many changes, for example getting rid of the sides originally proposed to hold the specimen in place, and modifications to other parts to make them more efficient. Additional parts were also added to the design with the help and advice …

Weld Thermal Simulation Of Crmov With Pwht In Type Iv Region, Bin Xu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

The Influence Of Welding Thermal Cycle On Microstructure And Mechanical Properties For 9cr2wvta Steel, Jian Wang, Shanping Lu, Lijian Rong, Dianzhong Li

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Xiaolong Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fundamental issues related to the selection of a metallic fuel casting furnace design are presented and discussed including heating mechanisms, casting issues, crucible design, and issues related to the mass transport of americium. The process of evaluating all of these different criteria is undertaken to select a concept that would have the greatest chance of success for casting americium in a metallic fuel rod. Based on this evaluation process, a concept for the casting of metallic fuel pins containing high vapor pressure materials is selected and discussed. The important physics of this concept include mass transport of americium from the …