Engineering Science and Materials Commons^™

On The Measurement Of Energy Dissipation Of Adhered Cells With The Quartz Microbalance With Dissipation Monitoring, Amir Monemian Esfahani, Weiwei Zhao, Jennifer Y. Chen, Changjin Huang, Ning Xi, Jun Xi, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We previously reported the finding of a linear correlation between the change of energy dissipation (ΔD) of adhered cells measured with the quartz crystal microbalance with dissipation monitoring (QCM-D) and the level of focal adhesions of the cells. To account for this correlation, we have developed a theoretical framework for assessing the ΔD-response of adhered cells. We rationalized that the mechanical energy of an oscillating QCM-D sensor coupled with a cell monolayer is dissipated through three main processes: the interfacial friction through the dynamic restructuring (formation and rupture) of cell-extracellular matrix (ECM) bonds, the interfacial viscous damping by the liquid …

Optical Direct Detection Of Thermal Vibrations Of Ultralow Stiffness Micro-Nano Structures., Sri Sukanta Chowdhury

Electronic Theses and Dissertations

A direct detection optical vibrometer is constructed around an 850 nm laser and a quadrant photodetector (QPD). The limit of detection is 0.2 fW which corresponds to a minimum amplitude of 0.1 Å. The vibrometer is used to measure the thermal vibration spectra of low stiffness micromechanical structures have nanometer features. One structure measured is a cantilevered 30 μm diameter glass fiber. Vibration amplitudes as low as 1.1 Å are measured. The thermal vibration spectra show fundamental resonances at 80-250 Hz and a signal to noise ratio (SNR) of 23-55 dB. Young’s modulus of glass in the cantilevers, estimated from …

Microstructural Effects On Photocatalytic Performance In Ag3po4/Bi2moo6 Z-Scheme Photocatalyst Systems, Kaleab Mengesha Ayalew

UNLV Theses, Dissertations, Professional Papers, and Capstones

As the world population continues to grow and access to modern industry become increasingly common, humanity finds itself amid an environmental and energy crisis. Natural resources, such as clean water are getting scarce. Currently, the development of high efficiency, green energy sources, and eco-friendly methods for water treatment have become a nonelective task. As a result, photocatalysis, as one of the most promising technologies in utilizing solar energy and pollutant removal, has attracted considerable attention.

However, the practical application of photocatalysis is still elusive because of the difficulty of finding an individual material that can satisfy all the requirements for …

Preparation Of Chitosan-Polyethylene Oxide-Colocasia Esculenta Flour Nanofibers Using Electrospinning Method, Riesca Ayu Kusuma Wardhani, Lia Asri, Muhamad Nasir, Bambang Sunendar Purwasasmita

Journal of Mechanical Engineering Science and Technology (JMEST)

Nanofibers have been prepared from the mixture of chitosan, polyethylene oxide (PEO) and Colocasia esculenta flour (CE flour) by using the electrospinning method. Two different nanofibers were formulated, containing chitosan-PEO and chitosan-PEO-CE flour. The higher concentration of PEO (3%chitosan-6%PEO) (w/v) resulted in more uniform chitosan-PEO electrospun nanofibers without beads. Chitosan-PEO-CE flour was prepared by addition of colloidal CE flour into the solution containing 3%chitosan-6%PEO with variation of the CE flour concentration of 5, 15 and 25% (w/v). Scanning Electron Microscopy demonstrated that the average diameter of chitosan-PEO nanofibers was 128±41 nm, whereas the diameter of chitosan-PEO-CE flour nanofibers was 159±45 …

Study On The Thermal Distortion, Hardness, And Microstructure Of St 37 Steel Plate Joined Using Fcaw, Maijuansyah Maijuansyah, Yanuar Rohmat Aji Pradana, Gaguk Jatisukamto, Solichin Solichin

Journal of Mechanical Engineering Science and Technology (JMEST)

This study sets out to investigate the distortion angle, microstructure, and hardness of St 37 steel plate weld joint produced by FCAW using the welding current of 80, 110, and 140 A. By using flat position, CO2 and E71T-1 wire were utilized as a shielding gas and electrode filler, respectively. The distortion angle measurement was done on 3 different locations of the welded sample perpendicular to weld direction by using bevel protractor. The micro Vickers tests were then applied gradually at the crosssectional surface with a distance of 0, 5, 10 and 15 mm from weld centerline using the load …

Comparison Study Of Mechanical Properties Of Al-Si Alloy With And Without Nanoreinforce Iron Oxide (Fe2o3), Cepi Yazirin, Poppy Puspitasari, Muhamad Fatikul Arif

Journal of Mechanical Engineering Science and Technology (JMEST)

Nanoreinforce materials such as ZnO, eggshell, Al2O3, TiO2, and ZrO2 have been shown to improve the mechanical properties of Al-Si alloy. Nanomaterial Fe2O3 has many applications as catalysts reaction in electronic devices, for example, semiconductor materials, paint formulations, lithium rechargeable batteries, and is often applied in industrial fields. It is known that Fe2O3 can be synthesized through the stirring process on machine and method used will involve several steps that relatively take a long time. In this study, Al-Si alloy reinforced by using nanomaterial Fe2O3 which sintered at a temperature of 600C for 3 hours aimed to improve mechanical and …

The Effect Of Chemical Pretreatment Process On Mechanical Properties And Porosity Of Bacterial Cellulose Film, Tito Arif Sutrisno, Heru Suryanto, Retno Wulandari, M. Muhajir, Shikh Mohd Shahrul Nizan Shikh Zahari

Journal of Mechanical Engineering Science and Technology (JMEST)

Bacterial cellulose (BC) is a natural polymer which have superior properties, like high porosity, high purity, and high permeability. The study objective is to determine the influence of chemical pretreatment on tensile strength and the porosity of BC. The method was to make BC films from pineapple peel extract through fermentation process for 14 days. The pretreatment was conducted by immersion of BC in BmimCl, H2O2, and NaOH solution with a concentration of 2.5%; 5%; and 7.5 %, heated at 80 °C then dried in the oven, and the samples were then tested by a tensile test using ASTM-D636-V standard, …

The Characteristic Of Overhang Object To Material Usage On Fdm 3d Printing Technology, Redyarsa Dharma Bintara, Aminnudin Aminnudin, Zumrotul Ida, Ferian Rizki Arbianto, Dani Prasetiyo

Journal of Mechanical Engineering Science and Technology (JMEST)

Fuse Deposition Modeling (FDM) 3D printing is one of additive manufacturing technology which physical 3D model is build up layer by layer. The support structure is almost involved on the process if overhang shape is met on the 3D model. It has main function to prevent the 3D printed model from collapsing. Commonly, the single material source of FDM 3D printer machine is to supply building two structure, structure of main 3D object and support structure. Hence, our goal optimizes the using of support material for reducing the main material usage. Furthermore, the sixteen of variation overhang angle is set …

Elastic Linear Analysis Of Connecting Rods For Single Cylinder Four Stroke Petrol Engines Using Finite Element Method, Didin Zakariya Lubis, Andoko Andoko

Journal of Mechanical Engineering Science and Technology (JMEST)

A connecting rod is one of the most critical parts in engine assembly which transfers energy from the piston to the crankshaft. The connecting rod mainly undergoes tensile and compressive loading under engine cyclic process. The forces acting on the connecting rod are forces due to maximum combustion pressure and forces due to the inertia of the connecting rod. This research aimed to analyze the design of the connecting rod of single-cylinder four-stroke engines. This study used CAD software for modeling and structural design. Stresses generated across all the locations of the connecting rod were evaluated using FEA Software. Elastic …

Observations Of Shear Stress Effects On Staphylococcus Aureus Biofilm Formation, Erica Sherman, Kenneth W. Bayles, Derek Moormeir, Jennifer Endres, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

Staphylococcus aureus bacteria form biofilms and distinctive microcolony or “tower” structures that facilitate their ability to tolerate antibiotic treatment and to spread within the human body. The formation of microcolonies, which break off, get carried downstream, and serve to initiate biofilms in other parts of the body, is of particular interest here. It is known that flow conditions play a role in the development, dispersion, and propagation of biofilms in general. The influence of flow on microcolony formation and, ultimately, what factors lead to microcolony development are, however, not well understood. The hypothesis being examined is that microcolony structures form …

Modeling Thermal And Mechanical Cancellation Of Residual Stress From Hybrid Additive Manufacturing By Laser Peening, Guru Madireddy, Chao Li, Jingfu Liu, Michael P. Sealy

Department of Mechanical and Materials Engineering: Faculty Publications

Additive manufacturing (AM) of metals often results in parts with unfavorable mechanical properties. Laser peening (LP) is a high strain rate mechanical surface treatment that hammers a workpiece and induces favorable mechanical properties. Peening strain hardens a surface and imparts compressive residual stresses improving the mechanical properties of a material. This work investigates the role of LP on layer-by-layer processing of 3D printed metals using finite element analysis. The objective is to understand temporal and spatial residual stress development after thermal and mechanical cancellation caused by cyclically coupling printing and peening. Results indicate layer peening frequency is a critical process …

Method For Fabrication Of A Soft-Matter Printed Circuit Board, Carmel Majidi, Tong Lu, Eric J. Markvicka

Department of Mechanical and Materials Engineering: Faculty Publications

A fabrication process for soft - matter printed circuit boards is disclosed in which traces of liquid - phase Ga - In eutectic ( eGaIn ) are patterned with UV laser micromachining ( UVLM ) . The terminals of the elastomer - sealed LM circuit connect to the surface mounted chips through vertically aligned columns of eGaIn - coated ferromagnetic micro spheres that are embedded within an interfacial elastomer layer .

Pseudo-Spectral Method To Control Three-Degree-Of-Freedom Wave Energy Converters, Ossama Abdelkhalik, Giorgio Bacelli, Shangyan Zou, Rush D. Robinett Iii, David G. Wilson, Ryan G. Coe

Michigan Tech Patents

The invention provides optimal control of a three-degree-of-freedom wave energy converter using a pseudo-spectral control method. The three modes are the heave, pitch and surge. A dynamic model is characterized by a coupling between the pitch and surge modes, while the heave is decoupled. The heave, however, excites the pitch motion through nonlinear parametric excitation in the pitch mode. The invention can use a Fourier series as basis functions to approximate the states and the control. For the parametric excited case, a sequential quadratic programming approach can be implemented to numerically solve for the optimal control. The numerical results show …

High-Performance Polyvinyl Chloride Gel Artificial Muscle Actuator With Graphene Oxide And Plasticizer, Taeseon Hwang, Zachary Frank, Justin Neubauer, Kwang Jin Kim

Mechanical Engineering Faculty Research

A transparent and electroactive plasticized polyvinyl chloride (PVC) gel was investigated to use as a soft actuator for artificial muscle applications. PVC gels were prepared with varying plasticizer (dibutyl adipate, DBA) content. The prepared PVC gels were characterized using Fourier-transform infrared spectroscopy, thermogravimetric analysis, and dynamic mechanical analysis. The DBA content in the PVC gel was shown to have an inverse relationship with both the storage and loss modulus. The electromechanical performance of PVC gels was demonstrated for both single-layer and stacked multi-layer actuators. When voltage was applied to a single-layer actuator and then increased, the maximum displacement of PVC …

Investigation Of Fundamental Principles Of Rigid Body Impact Mechanics, Khalid Alluhydan

Mechanical Engineering Research Theses and Dissertations

In impact mechanics, the collision between two or more bodies is a common, yet a very challenging problem. Producing analytical solutions that can predict the post-collision motion of the colliding bodies require consistent modeling of the dynamics of the colliding bodies. This dissertation presents a new method for solving the two and multibody impact problems that can be used to predict the post-collision motion of the colliding bodies. Also, we solve the rigid body collision problem of planar kinematic chains with multiple contacts with external surfaces.

In the first part of this dissertation, we study planar collisions of Balls and …

Influence Of Tempering And Cryogenic Treatment On Retained Austenite And Residual Stresses In Carbonitrided 18crnimo7-6 Low Alloy Steel, Richard Katemi

Tanzania Journal of Engineering and Technology (TJET)

This work investigated the influence of tempering conditions coupled with cryogenic treatment on thermal stabilization of retained austenite and residual stress distributions in carbonitrided 18CrNiMo76 low alloy steel samples. The carbonitriding conditions were set to enable attaining surface carbon and nitrogen content of 0.87 and 0.34 mass.-percent respectively. After carbonitriding, some of the samples were subjected to varying tempering conditions followed by cryogenic treatment at-120 °C using nitrogen gas. Analysis of both retained austenite and residual stresses was conducted using X-ray diffraction. In the as-quenched state, carbonitrided samples contained 52 mass.-percent. Samples that were directly subjected to the cryogenic treatment …

Electrocatalytic Nanomaterials For Reduction Of Hydrogen Peroxide As Potential Radioprotectors, Rui-Hong Jia, Jin-Xuan Zhang, Xiao-Dong Zhang, Mei-Xian Li

Journal of Electrochemistry

Nanomaterials have shown many potential application prospects in the biomedical field, such as medical imaging, drug delivery and biosensing due to their unique physical and chemical properties. In this review we focus on nanomaterials that have shown not only abilities of radiation protection, but also good electrocatalytic activities toward reduction reactions of hydrogen peroxide and oxygen. We discuss the abilities of radiation protection of these nanomaterials that are ascribed to their enzyme-like activities because their catalytic properties provide an effective pathway for scavenging free radicals in vivo via rapid reactions with reactive oxygen species. We also provide insights into electrocatalytic …

Generating Electrospray From A Ferrofluid, Lyon Bradley King

Michigan Tech Patents

An electrospray device for generating electrospray from a ferrofluid. The electrospray device includes an emitter, an extraction electrode, and a magnet. The emitter is configured to receive a ferrofluidic liquid. The extraction electrode includes an aperture and is positioned a first distance from the emitter. The magnet generates a magnetic field in a first direction toward the emitter. The magnetic field causes Rosensweig instability in the ferrofluidic liquid, and generates a ferrofluidic peak in the ferrofluidic liquid. The magnet is positioned a second distance from the emitter, and the emitter is positioned between the extraction electrode and the magnet. The …

Group Iv Environmentally Benign, Inexpensive Semiconductor Nanomaterials For Solar Cells, Lisa Je

ENGS 86 Independent Projects (AB Students)

Modern solar cells are composed of silicon, cadmium tellurium, and copper indium gallium diselenide. While these materials are efficient, elements such as cadmium and indium are rare and expensive. To make this renewable energy source more inexpensive and sustainable, the Liu Optics lab is substituting expensive rare earth metals for more commonly found transition state metals. Work has been done to replace the solar cell layers composed of cadmium and gallium to replace them with glass, silicon, and/or thin films. Common metals such as germanium and tin are investigated and characterized to provide a platform for solar cell components.

Effects Of Heat Treatment On The Dimensional Stability And Mechanical Properties Of Guadua Bamboo, Kade Schmitz, Skye Dascher, Shalto Dascher

Materials Engineering

Contributing to about 4% of particulate emissions, the construction industry is one of the largest polluters of the environment. In an effort to reduce emissions, BamCore has produced a dual panel wall system made of Guadua bamboo with a Douglas fir veneer. Bamboo is a highly renewable material with a fast growth rate and carbon sequestration abilities. This project investigates how heat treating Guadua bamboo influences its dimensional changes and mechanical properties for building applications. It was found that a dimensional increase in every direction occurred for all samples when exposed to higher relative humidity (50% to 90%), and that …

Me-Em Enewsbrief, June 2019, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Design And Control Of Fiber Encapsulation Additive Manufacturing, Matt Saari

Mechanical Engineering Research Theses and Dissertations

This work presents the design, development, and analysis of the Fiber Encapsulation Additive Manufacturing (FEAM) system developed at the Laboratory for Additive Manufacturing Robotics \& Automation at the Lyle School of Engineering at Southern Methodist University. The innovation introduced by FEAM is the ability to insert a continuous fiber of different material into the flowing extrudate. Correctly positioning the fiber feed inside the extrudate while turning the fiber in arbitrary directions is a critical aspect of the technology. This will allow for the full exploitation of the capabilities of the FEAM technology to produce robotic components that actuate and sense. …

Multifunctional Properties Of Gan Nws Applied To Nanometrology, Nanophotonics, And Scanning Probe Microscopy/Lithography, Mahmoud Behzadirad

Optical Science and Engineering ETDs

GaN nanowires are promising for optical and optoelectronic applications because of their waveguiding properties and large optical bandgap. Recent researches have shown superior mechanical properties of GaN nanowires which promises their use in new research areas e.g. nanometrology. In this work, we develop a scalable two-step top-down approach using interferometric lithography as well a bottom-up growth of NWs using MOCVD, to manufacture highly-ordered arrays of nanowires with atomic surface roughness and desired aspect-ratios to be used in nanophotonics and atomic precision metrology and lithography. Using this method, uniform nanowire arrays were achieved over large-areas (~1 mm²) with aspect-ratio …

Defect Chemistry And Ion Intercalation During The Growth And Solid-State Transformation Of Metal Halide Nanocrystals, Bo Yin

McKelvey School of Engineering Graduate Student Theses & Dissertations

Abstract of the Dissertation

Defect Chemistry and Ion Intercalation During the Growth and Solid-State Transformation of Metal Halide Nanocrystals

Semiconductor metal halides as light-sensitive materials have applications in multiple areas, such as photographic film, antibacterial agents and photocatalysts. One focus of this dissertation is to achieve novel morphologies of ternary silver bromoiodide (AgBr1-xIx, 0

For the silver halide system, we demonstrate that the anion composition of AgBr1-xIx nanocrystals determines their shape through the introduction of twin defects as the nanocrystals are made more iodide-rich. AgBr1-xIx nanocrystals grow as single-phase, solid solutions with the rock salt crystal structure for anions compositions …

Agent-Based Microgrid Architecture For Generation Following Protocols, Steven Goldsmith

Michigan Tech Patents

A system for predicting power and loads over a single, relatively short time horizon. More specifically, a system comprising a Storage Agent (S-agent) Cohort within a grid control society, wherein the system expands G and L intra-cohort protocols to allow the S-cohort to participate in power management of the grid by scheduling storage components in source or load roles as determined by the time-varying state of the power imbalance and by the risk-adjusting capacity margin relationship between the G and L cohorts.

Wearable Devices For Single-Cell Sensing And Transfection, Lingqian Chang, Yu-Chieh Wang, Faheem Ershad, Ruiguo Yang, Cunjiang Yu, Yubo Fan

Department of Mechanical and Materials Engineering: Faculty Publications

Wearable healthcare devices are mainly used for biosensing and transdermal delivery. Recent advances in wearable biosensors allow for long-term and real-time monitoring of physiological conditions at a cellular resolution. Transdermal drug delivery systems have been further scaled down, enabling wide selections of cargo, from natural molecules (e.g., insulin and glucose) to bioengineered molecules (e.g., nanoparticles). Some emerging nanopatches show promise for precise single-cell gene transfection in vivo and have advantages over conventional tools in terms of delivery efficiency, safety, and controllability of delivered dose. In this review, we discuss recent technical advances in wearable micro/nano devices with unique capabilities or …

Transferring Power Through A Magnetic Couple, Nickolas Cruz Villalobos Jr.

Senior Theses

Properties of several working magnetic coupled rotors have been measured and their performance compared to theoretical models. Axial magnetic couplers allow rotors to work within harsh environments, without the need for seals, proper alignment, or overload protection on a motor. The influence of geometrical parameters, such as distance from the center of the rotors, polarity arrangement, and the number of dipole pairs were experimentally tested. These results can be used to improve rotor designs, to increase strength and efficiency.

Predicting The Mechanical Properties Of Nanocomposites Reinforced With 1-D, 2-D And 3-D Nanomaterials, Scott Edward Muller

Graduate Theses and Dissertations

Materials with features at the nanoscale can provide unique mechanical properties and increased functionality when included as part of a nanocomposite. This dissertation utilizes computational methods at multiple scales, including molecular dynamics (MD) and density functional theory (DFT), and the coupled atomistic and discrete dislocation multiscale method (CADD), to predict the mechanical properties of nanocomposites possessing nanomaterials that are either 1-D (carbyne chains), 2-D (graphene sheets), or 3-D (Al/amorphous-Si core-shell nanorod).

The MD method is used to model Ni-graphene nanocomposites. The strength of a Ni-graphene nanocomposite is found to improve by increasing the gap between the graphene sheet and a …

The Development Of A Viscoelastic Ellipsoidal Model For Use In Measuring Plantar Tissue Material Properties During Walking, Jessica Lee Deberardinis

UNLV Theses, Dissertations, Professional Papers, and Capstones

Introduction: The mechanical characteristics of the plantar tissues during walking is not well understood as most of the current research focuses on testing specific plantar regions in cadavers or while the feet of the participants are raised. In this work, it is hypothesized that a viscoelastic geometric ellipsoid model used to assess multiple structures of the foot would be accurate and robust. This model would be participant-specific and applicable to the entire stance phase of gait.

Methods: The proposed viscoelastic ellipsoid model would represent several key anatomical areas: Heel, Posterior Midfoot, Anterior Midfoot, Metatarsals 1-2, Metatarsals 3-5, Toe 1, Toe …

Equation Of State Of H2o Ice Using Melt-Recrystallization, Zachary Michael Grande

UNLV Theses, Dissertations, Professional Papers, and Capstones

The recent surge in exoplanet discoveries due to advancements in astrophysical technology and analysis has brought the reliability of early equation of state measurements into question as they are the limiting factor when modeling composition of these planets. H2O content is among the most important for the search of habitable planets as well as in understanding planetary dynamics and atmosphere formation. Over the last three decades the equation of state of H2O has been investigated with various techniques but, has suffered from anisotropic strain and poor powder statistics resulting in a large discrepancy in equation of state fits. At pressures …