Engineering Science and Materials Commons^™

Additive Manufacturing With High Density Polyethylene: Mechanical Properties Evaluation, Calvin Wampol

Electronic Theses and Dissertations

High-density polyethylene is a common recyclable plastic that has a large potential as an additive manufacturing material due its economic and environmental benefits. However, high-density polyethylene has undesirable thermal properties that cause the material to shirk and not adhere to the printing bed during an additive manufacturing processes. Researchers have attempted to combat these thermal properties but have only created novel filaments of high-density polyethylene without being able to create 3D printed specimens for mechanical property testing. This paper presents several methods to create 3D printed specimens with pure high-density polyethylene filament on a fused filament fabrication type 3D printer. …

Structural And Aerodynamic Design, Procedure And Analysis Of A Small V-Shaped Vertical Axis Wind Turbine, Odari J. Whyte

College of Graduate Studies: Theses & Dissertations

Over the last two decades there has been a renewed interest in Vertical Axis Wind Turbines. This turbine configuration though unpopular for large-scale generation has found a niche market in the way of offshore energy harvesting. However, offshore wind has its challenges. In this thesis a detailed comprehensive study of a proposed V-shaped vertical axis turbine rotor is performed in order to examine its structural and aerodynamic characteristics. The design met and exceeded the safety parameters establish for test bed operation, showing a factor of safety of 1.87 with regard to fatigue stress response. A satisfactory fatigue stress design life …

Thermal-Fatigue And Thermo-Mechanical Equivalence For Transverse Cracking Evolution In Laminated Composites, Javier Cabrera Barbero

Graduate Theses, Dissertations, and Problem Reports (ETD)

Carbon fiber reinforced plastics (CFRP) are potential materials for many aerospace and aeronautical applications due to their high specif strength/weight and a low coeffcient of thermal expansion (CTE) resulting in a high long-term stability. Among candidate structures, the re-entry reusable launch vehicles (RLV), the fuel oxidant storage and transportation at cryogenic temperature, space satellites, and aircraft structure (frame, wings, etc...) can be highlighted. However, CFRP are prone to internal damage as a result of high residual stresses and thermal fatigue loading. In this study, micro-cracking damage evolution in laminated composites subjected to monotonic cooling and thermal cyclic loads is developed …

Characterization Of 3d Printed Polylactic Acid/ Polycaprolactone/Titanium Dioxide Composites For Bone Replacement And Grafting, Sandra Elena Najera Beltran

Open Access Theses & Dissertations

A material that mimics the properties of bones was developed by optimizing the ratio of polymer composites of polylactic acid (PLA) and poly-ε-caprolactone (PCL), containing small amounts of titanium oxide (TiO2). Although titanium-based alloys have commonly been used for bone replacement procedures due to their biocompatibility with the human body and their mechanical properties, stress shielding continues to be a problem. The structure of a bone has a porosity which permits the flow of nutrients, blood, oxygen and minerals, and is an issue at the time of creating bone replacements using conventional methods. PLA and PCL have been used in …

Solvent And Concentration Effects Governing The Hierarchical Organization Of Asphaltenes: A Small-Angle X-Ray Scattering Study, Hasan Rejoanur Rahman

Open Access Theses & Dissertations

Asphaltenes are a group of planar molecules found in crude oil and are prone to aggregation which often causes blockage of pipes along the oil production stream resulting a huge economic downside. In an effort to understand the hierarchical organization of asphaltene in different solvents and concentrations, the solution structure of various asphaltene solutions were studied using small-angle x-ray scattering (SAXS). Solvents were chosen based on miscibility maps. Such maps are generated on the critical value of the solubility parameter difference between asphaltenes or asphaltene components, and a range of solvents. The critical factors that affect asphaltene and asphaltene component …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Spectrally-Selective Energy-Harvesting Solar Windows For Public Infrastructure Applications, Mikhail Vasiliev, Kamal Alameh, Mohammad Alam

Research outputs 2014 to 2021

A study of photovoltaic solar window technologies is reported and it focuses on their structural features, functional materials, system development, and suitability for use in practical field applications including public infrastructures and agricultural installations. Energy generation performance characteristics are summarized and compared to theory-limit predictions. Working examples of pilot-trial solar window-based installations are described. We also report on achieving electric power outputs of about 25 Wp/m2 from clear and transparent large-area glass-based solar windows.

Influence Of Substrate Stage Temperature And Rotation Rate On The Magneto-Optical Quality Of Rf-Sputtered Bi2.1dy0.9fe3.9ga1.1o12 Garnet Thin Films, Mohammad E. Alam, Mikhail Vasiliev, Kamal Alameh

Research outputs 2014 to 2021

Highly bismuth-substituted iron garnet thin films are prepared on quartz substrates by using a radio frequency (RF) magnetron sputtering technique. We study the factors (process parameters associated with the RF magnetron sputter deposition technique) affecting the magneto-optical (MO) properties of ferrite garnet films of composition Bi2.1Dy0.9Fe3.9Ga1.1O12. All films show high MO response across the visible range of wavelengths after being annealed. In particular, the effects of substrate stage temperature and rotation rate on the various properties of films are studied. Experimental results reveal that the characteristics of garnet films of this type can be tuned and optimized for use in …

Evaluation Of Procurement Scenarios In One-Dimensional Cutting Stock Problem With A Random Demand Mix, Hüseyin Sarper, Nebojsa I. Jaksic

Electrical & Computer Engineering Faculty Publications

The one-dimensional cutting stock problem describes the problem of cutting standard length stock material into various specified sizes while minimizing the material wasted (the remnant or drop as manufacturing terms). This computationally complex optimization problem has many manufacturing applications. One-dimensional cutting stock problems arise in many domains such as metal, paper, textile, and wood. To solve it, the problem is formulated as an integer linear model first, and then solved using a common optimizer software. This paper revisits the stochastic version of the problem and proposes a priority-based goal programming approach. Monte Carlo simulation is used to simulate several likely …

Leaching Of A Mongolian Chalcopyrite Concentrate, Nicholas J. Welham, Jadambaa Temuujin, Nader Setoudeh

Research outputs 2014 to 2021

A Mongolian chalcopyrite flotation concentrate was leached using sodium hypochlorite adjusted to different pH using hydrochloric acid. It was found that using a starting pH of below 5.0 resulted in more efficient leaching. The extent of chalcopyrite leaching was determined by the concentration of sodium hypochlorite with > 40% dissolution being achieved. The residue after leaching was found to consist primarily of unreacted chalcopyrite which would be suitable for further leaching or smelting.

Effects Of Air And Other Gases In The Stabilization Process Of The Superprotonic Phase Of Cesium Dihydrogen Phosphate Within A Hermetically Sealed Chamber, Israel Martinez

Open Access Theses & Dissertations

The solid acid CsH2PO4 (CDP), exhibits a sudden increase in its proton conductivity as it’s heated above a certain temperature (around T~235oC), which makes it a very attractive candidate to be used as an electrolyte in intermediate temperature fuel cells. Unfortunately, at these temperatures the sample is not stable, as starts to dehydrate; which causes a dramatic drop in the proton conductivity over a short period of time (less than one hour). In order to inhibit, or at least delay, the dehydration process, the solid acid it’s put under a saturated water vapor atmosphere. Another method to stabilize the highly …

Implementation Of Magnesium Alloy Az91d On Wire And Arc Additive Manufacturing, David Adrian Martinez Holguin

Open Access Theses & Dissertations

As progress on Additive Manufacturing (AM) techniques focusing on ceramics and polymers evolve, metals continue to be a challenging material to manipulate when fabricating products. Current methods, such as Selective Laser Sintering (SLS) and Electron Beam Melting (EBM) face many intrinsic limitations due to the nature of their processes. Material selection, elevated cost and low deposition rates are some of the barriers to consider when one of these methods is to be used for the fabrication of engineering products. The research here presented demonstrates the use of a Wire and Arc Additive Manufacturing (WAAM) system for the creation of metallic …

การประมาณค่าในช่วงเชิงพหุนามลากรานจ์ร่วมกับตัวประกอบถ่วงน้ำหนักนอกช่วงแบบใหม่เพื่อแก้ปัญหาการไหลภายในช่องว่างสี่เหลี่ยมผืนผ้า, อุทัย ประสพชิงชนะ

Chulalongkorn University Theses and Dissertations (Chula ETD)

งานวิจัยนี้มีวัตถุประสงค์เพื่อนำเสนอแผนแบบใหม่ที่มีชื่อว่าแผนแบบ LIP (Lagrange Interpolating Polynomial scheme) และการประมาณค่านอกช่วงแบบใหม่ที่มีชื่อว่าการประมาณค่านอกช่วงแบบ WF-LIP (Weighting Factors with Lagrange Interpolating Polynomial extrapolation) โดยแผนแบบ LIP ถูกใช้สำหรับการประมาณค่าของตัวแปรและอนุพันธ์ของตัวแปรทั้งเทียบกับระยะและเวลาในระเบียบวิธีไฟไนต์วอลู่ม ข้อดีของแผนแบบ LIP คือ เป็นแผนที่มีความแม่นยำลำดับสี่ เป็นแผนที่ง่ายต่อการพัฒนาโปรแกรมที่ใช้การแก้ปัญหาด้วยเม็สซ์ที่ไม่สม่ำเสมอ และเป็นทั้งแผนทางระยะและแผนทางเวลา สำหรับการประมาณค่านอกช่วงแบบ WF-LIP ถูกนำมาใช้ในการหาค่าคาดเดาเริ่มต้นของตัวแปรในแต่ละช่วงเวลาย่อยของปัญหาที่สภาวะไม่คงตัว ซึ่งใช้วิธีการหาคำตอบของแต่ละช่วงเวลาย่อยด้วยวิธีการทำซ้ำ จากผลการตรวจสอบความถูกต้องของคำตอบที่คำนวณจากแผนแบบ LIP และการทดสอบประสิทธิภาพของการประมาณค่านอกช่วงแบบ WF-LIP พบว่า คำตอบที่คำนวณจากแผนแบบ LIP มีความถูกต้องและมีความสอดคล้องกับคำตอบที่นำมาใช้ในการเปรียบเทียบความถูกต้อง ขณะที่การประมาณค่านอกช่วงแบบ WF-LIP สามารถช่วยลดระยะเวลาที่ใช้ในการคำนวณเพื่อหาคำตอบของปัญหาได้สูงสุดถึงร้อยละ 49.69 เมื่อเทียบกับกรณีที่การคำนวณหาคำตอบ โดยไม่ได้ใช้การประมาณค่านอกช่วงแบบ WF-LIP

Magnetic And Catalytic Properties Of Transition Metal Doped Mos2 Nanocrystals, Luis Martinez

Open Access Theses & Dissertations

Magnetism and catalytic activity of nanoscale layered two-dimensional (2D) transition metal dichalcogenides (TMDs) have gained an increasing research interest in the recent past. To broaden the current knowledge and understanding on this subject, in this work, together with my collaborators, I study the magnetic and electrocatalytic properties of hydrothermally grown pristine and transition metal doped (10% of Co, Ni, Fe and Mn) 2H-MoS2 nanosheets/nanocrystals (NCs), with the particle size of 25-30 nm. A broad range of experimental measurements such as x-ray diffraction, transmission electron microscopy, x-ray photo absorption spectroscopy, Raman spectroscopy, magnetic, catalytic and electron spin resonance have been employed …

Tribological Characterization Of Ti-Based Alloys For Biomedical Applications In Simulated Body Fluid, Edgar Reyes

Open Access Theses & Dissertations

Tribology is a terminology introduced in the 1960's and it is a study that relates to the investigation of the damage of materials. Titanium, as a material used for a wide range of application, it has been brought to the attention of researchers some characteristics such as its much lower density if compared to steel, its capability as an alloying agent with an amount of metals to enhance physical and mechanical properties, to name just a few characteristics. This paper will discuss the performance on tribology behavior in two different Titanium alloys. These Titanium alloys are Ti-6Al-4V (Ti64), and Ti-24Nb-4Zr-8Sn …

Development And Characterization Of Novel Materials For The Advancement Of Additive Manufacturing By Material Extrusion 3d Printing, Jose Gilberto Siqueiros

Open Access Theses & Dissertations

The development of additive manufacturing technologies has been under the spotlight from the past decade due to its enormous potential to disrupt current manufacturing processes. Material extrusion 3D printing (ME3DP) is the most common type of additive manufacturing technology as it experienced an exponential growth after the expiration of the fused deposition modeling patent filed in 1989 by Scott Crump. The large interest behind this technology is generated from the capacity to create complex shapes, rapid prototyping, relatively ease of use, low cost, and high accessibility. The gradual evolution of material extrusion 3D printing calls to become a technology ordinarily …

Tungsten Doping Induced Superior Mechanical Properties Of Hafnium Oxide For Energy Applications, Ann Marie Uribe

Open Access Theses & Dissertations

Hafnium oxide, or hafnia, is a high temperature refractory material with good electrical, chemical, optical, and thermodynamic properties. The effects of dopants have been widely studied, especially after the discovery of ferroelectricity induced in hafnia thin films. While attractive and used in the opto-electronic, memory devices, and semiconductor industries, there is a lack in the literature on enhancing the mechanical properties of hafnium oxide, specifically through doping it with tungsten, another material of interest particularly for future high temperature device applications. Thus, this work aimed to grow hafnia thin films doped with varying amounts of tungsten. The samples were grown …

Heterogeneous Integration Of Metallic, Semiconducting And Dielectric Two-Dimensional Layered Material Inks For Electronics And Sensing Device Platforms, Jay Amrish Desai

Open Access Theses & Dissertations

In monolayers of two-dimensional (2-D) layered materials, the motion of electrons is confined to a 2-D plane yielding a "zero" effective thickness with regard to the electrons. These monolayers are commonly obtained by exfoliating membranes from the bulk crystal to overcome the weak interplanar Van der Waals bonding using the so-called top-down approach. The bottom-up approach is another avenue to realize these materials, where atoms and molecules coalesce together into increasingly larger assemblies for the realization of the bulk three-dimensional (3-D) crystal. The unique properties of many of these 2-D materials make them highly sought out candidates for advancing conventional …

A New Approach To Multiplanar, Real-Time Simulation Of Physiological Knee Loads And Synthetic Knee Components Augmented By Local Composition Control In Fused Filament Fabrication, Joshua Taylor Green

Open Access Theses & Dissertations

Despite numerous advances in biomedical engineering, few developments in surgical simulation have been made outside of computational models. Cadavers remain the primary media on which surgical research and simulation is conducted. Most attempts to quantify the effects of orthopedic surgical methods fail to achieve statistical significance due to limited quantities of cadaver specimen, large variations among the cadaver population, and a lack of repeatability among measurement techniques. The general purpose of the research covered in this dissertation is to develop repeatable simulation of physiological loads and develop techniques to fabricate a synthetic-based replacement of cadaver specimens. Future work applying this …

Structural And Optical Investigations Of Rbxcs1-Xh2po4, Alex D. Price

Open Access Theses & Dissertations

Proton conductor solid acid electrolytes RbxCs1-xH2PO4 (0≤x≤1) have been investigated using second harmonic generation and powder x-ray diffraction. Second harmonic generation is an optical technique which can be used to study the structural properties of materials. Microscopes of this nature have the ability to image objects with a variable penetration depth in a non-destructive manner, allowing for great potential to be used for in situ observations of the electrolyte’s structure when in a fuel cell under operating conditions.

X-ray powder diffraction was carried out on the series of samples and found for values of 0≤x≤0.5 the structure of the material …

Titanium Incorporated Gallium Oxide (Ga-Ti-O): Structure Property Relationship And Performance Evaluation For Extreme Environment Applications, Sandeep Manandhar

Open Access Theses & Dissertations

The existing power generation systems, which utilize fossil fuels, are in dire need of efficient, reliable chemical sensors that can operate safely at higher temperatures. These sensors control the combustion environment and the emissions during combustion. Several sensing materials such as SnO2, ZnO, TiO2, WO3, and Ga2O3 exhibit high sensitivity to certain type of chemical molecules and in a certain range of temperatures. Among these candidate materials, β-Ga2O3 is stable at very high temperatures and has shown functionality for oxygen sensing at higher temperatures (>700°C). However, the response time and sensitivity must be significantly improved in order to derive …

Streamlining Alloy Design And Thermo-Mechanical Processing Parameters For High Strength Line Pipe Steels And Hot Rolled Microalloyed Steels: Process - Structure - Property Paradigm, Venkata Vignesh Natarajan

Open Access Theses & Dissertations

The process parameters related to thermo-mechanical controlled processing (TMCP) of steels play a vital role in affecting the ultimate mechanical properties. We illustrate here the impact of coiling temperature, the impact of finish cooling temperature on interrupted cooling and compare with continuous cooling, and the impact of carbon and niobium on the microstructure and precipitation behavior and corresponding changes in mechanical properties, in an ultrahigh strength titanium-niobium microalloyed steel. The microstructural advancement was contemplated via transmission electron microscopy and electron backscattered diffraction (EBSD). The goal was to underscore the impact of coiling temperature on the nature and distribution of microstructural …

Evaluation Of Large Area Additively Manufactured Fiber Reinforced Acrylonitrile Butadiene Styrene (Abs), Kevin Schnittker

Open Access Theses & Dissertations

To enable the advancement of large-scale additive manufacturing processes, it is necessary to establish and standardize methodologies to characterize the mechanical properties of printed test coupons. Due to the large size of the print beads, conventional test standards are inadequate. The focus of this study was to determine the feasibility of using Digital image correlation (DIC) technology as a key enabler for robust data collection of strain measurements of large 3D printed parts. To incorporate the DIC measurements, a novel method was developed to prepare large 20 wt.% glass filled ABS test coupons for adequate contrast. Through this technique, Poisson's …

Microstructural Characterization Of LensTm Ti-6al-4v: Investigating The Effects Of Process Variables Across Multiple Deposit Geometries, Laura Christine Davidson

Browse all Theses and Dissertations

Laser based additive manufacturing of Ti-6Al-4V components is under consideration for aerospace applications. The mechanical properties of the finished components depend on their microstructure. Process mapping compares process variables such as heat source power, heat source travel speed, material feed rate, part preheat temperature and feature geometry to process outcomes such as microstructure, melt pool geometry and residual stresses. In this work, the microstructure of two-dimensional pads, multilayer pads, thin walls, and structural components at the steady state location was observed. A method for measuring β grain widths that allows for the calculation of standard deviations, confidence intervals, and variances …

Galvanic And Pitting Corrosion Of A Fastener Assembly, Julie Shallman

Williams Honors College, Honors Research Projects

This research focuses on coupled galvanic/pitting corrosion of AA7075 when combined with stainless steel in a fastener assembly. A one-dimensional mathematical model of a well-mixed thin film electrolyte is developed to predict the damage profile of the AA7075 surface when its protective coating is damaged. The damage exposes the galvanic couple. A time dependent system of partial differential equations for potential, chloride concentration, aluminum ion concentration, and damage is developed and solved numerically. Two approaches to calculate the current density within aluminum pits are discussed. The first is a current balance between the cathodic, anodic and passive portions of the …

Defect Engineering: Novel Strengthening Mechanism For Low- Dimensional Zinc Oxide Nanostructures, Seyed Emad Rezaei

Browse all Theses and Dissertations

The advent of nanomaterials has opened a new avenue for designing and fabricating materials with unique properties, e.g., superior mechanical properties. Based on a common notion, the perfect structures are assumed to exhibit better mechanical properties, such as higher yield strength and Young's modulus. Therefore, researchers have devoted an extensive amount of time to decrease defect concentration by fabricating materials with the micro/nanoscale, e.g., nanowires (NWs) and nanobelts (NBs), to enhance the mechanical characteristics of the system. However, defects are a part of the fabrication process and precise control over synthesizing procedure is needed to eliminate them from the material. …

Functionalization And Characterization Of Chemical Vapor Deposited Graphene Sheets Towards Application In Chemical Vapor Sensing, Nicholas Alexander Engel

Browse all Theses and Dissertations

Chemical/biological sensors serve many purposes in protecting machinery, the environment, and human life/wellness. Graphene, a two-dimensional (2-D) material made up of carbon atoms in a honeycomb-like lattice, is promising for applications to chemical/biological sensing due to its unique properties. Functionalization of graphene by surface decorating with nanoparticles and increasing interior adsorption sites can tailor its catalytic activity and electrical properties, and hence, important for detecting and distinguishing trace hazardous gases. This research introduces two different approaches to functionalize graphene towards enhanced sensitivity and selectivity of graphene-based sensors. The morphologies, structures, and electrical properties of the functionalized graphene are systematically characterized. …

Magneto-Optical Properties Of Thin Permalloy Films: A Study Of The Magneto-Optical Generation Of Light Carrying Angular Momentum, Patrick D. Montgomery

Theses and Dissertations--Electrical and Computer Engineering

Magneto-optical materials such as permalloy can be used to create artificial spin- ice (ASI) lattices with antiferromagnetic ordering. Magneto-optical materials used to create diffraction lattices are known to exhibit magnetic scattering at the half- order Bragg peak while in the ground state. The significant drawbacks of studying the magneto-optical generation of OAM using x-rays are cost, time, and access to proper equipment. In this work, it is shown that the possibility of studying OAM and magneto-optical materials in the spectrum of visible light at or around 2 eV is viable. Using spectroscopic ellipsometry it is possible to detect a change …

Flow Patterns Through Vascular Graft Models With And Without Cuffs, Chia Min Leong, Gary B. Nackman, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

The shape of a bypass graft plays an important role on its efficacy. Here, we investigated flow through two vascular graft designs±with and without cuff at the anastomosis. We conducted Digital Particle Image Velocimetry (DPIV) measurements to obtain the flow field information through these vascular grafts. Two pulsatile flow waveforms corresponding to cardiac cycles during the rest and the excitation states, with 10% and without retrograde flow out the proximal end of the native artery were examined. In the absence of retrograde flow, the straight end-to-side graft showed recirculation and stagnation regions that lasted throughout the full cardiac cycle with …

Dislocations Interaction Induced Structural Instability In Intermetallic Al2cu, Qing Zhou, Jian Wang, Amit Misra, Ping Huang, Fei Wang, Kewei Xu

Department of Mechanical and Materials Engineering: Faculty Publications

Intermetallic precipitates are widely used to tailor mechanical properties of structural alloys but are often destabilized during plastic deformation. Using atomistic simulations, we elucidate structural instability mechanisms of intermetallic precipitates associated with dislocation motion in a model system of Al₂Cu. Interaction of non-coplanar <001> dislocation dipoles during plastic deformation results in anomalous reactions—the creation of vacancies accompanied with climb and collective glide of <001> dislocation associated with the dislocation core change and atomic shuffle—accounting for structural instability in intermetallic Al₂Cu. This process is profound with decreasing separation of non-coplanar dislocations and increasing temperature and is likely to be …