Engineering Science and Materials Commons^™

Electrochemical Performance Of Moo2-C Composite Coatings, Quan-Yi Li, Qi Yang, Yan-Hong Zhao

Journal of Electrochemistry

The molybdenum dioxide-carbon(MoO₂-C)composite coatings on the surface of Cu foils were prepared by simple knife coating route and followed by sintering in vacuum. The morphology, composition, structure and electrochemical performance of the MoO₂-C composite coatings were investigated. The results demonstrated that the MoO₂-C composite coatings consist of MoO₂ nano-particles with monoclinic crystal structure and amorphous carbon. Some MoO₂ nano-particles with a size range of 5-30nm were loaded on the surface of carbon matrices; while some MoO₂ nano-particles with a size of ~5nm were encapsulated inside. The composite coatings showed porous structure …

Preparation Of Co3O4/Ti Electrocatalytic Membrane Electrode For Catalytic Oxidation Of Benzyl Alcohol, Yu-Mei Zheng, Zhen Yin, Hong Wang, Jian-Xin Li

Journal of Electrochemistry

The cobalt oxide(Co₃O₄) nanoparticles were loaded on microporous Ti membrane to prepare Co₃O₄/Ti electrocatalytic membrane electrode by dip-coating method. The microstructures and electrochemical properties of Co₃O₄/Ti electrocatalytic membrane were investigated. The Co₃O₄/Ti electrocatalytic membrane reactor (ECMR) assembled by using the Co₃O₄/Ti electrocatalytic membrane as an anode was adopted for catalytic oxidation of benzyl alcohol to produce benzaldehyde and benzoic acid.The effects of different operation parameters on benzyl alcohol conversion, and selectivity to benzaldehyde and benzoic acid of ECMR were studied. …

Electrochemical Oxidation Of P-Chlorophenol On Porous Ti/Bdd Electrode Cooperated With Cathode Dechlorination, Rong-Ling Chen, Wei-Min Huang, Ya-Peng He, Jun Shi, Hai-Bo Lin

Journal of Electrochemistry

The electrochemical oxidation of p-chlorophenol on porous Ti/BDD electrode cooperated with synergistic effect of cathode dechlorination was studied. Electrochemical degradation tests of p-chlorophenol were conducted in single and double compartment electrolytic cells separately, and the results showed that the mineralization happened mainly in the anode region. The product of chloride ions produced from the cathodic reduction of 4-chlorophenol in the single cell migrated to the anode region and further generated active chlorine toward electro-catalytic oxidation. At the same time, the chloride ion produced from the cathode of the double cell was difficult to be migrated to the anode region, which …

Preparations And Corrosion Protection Investigations Of Diethylene Triamine Penta(Methylene Phosphonic Acid)-Zn2+ Conversion Coatings On Cold Rolled Steel Substrates, Wei He, Ru Yan, Ying-Qi Wang, Xiang Gao, Hou-Yi Ma

Journal of Electrochemistry

Novel diethylene triamine penta(methylene phosphonic acid) (DTPMPA)-zinc ion (Zn²⁺) conversion coatings with uniform blue color and excellent corrosion protection were directly formed on the cold rolled steel (CRS) substrates by immersing a CRS plate into the film-forming solutions containing the appropriate concentrations of DTPMPA and Zn²⁺ ion at the proper pH. In this paper, surface morphologies and elemental compositions of DTPMPA-Zn²⁺ conversion coatings were characterized by SEM and EDS, respectivey. The surface functional groups, chemical constituents and binding modes to the substrates were investigated by means of FTIR and XPS methods. The influences of DTPMPA concentrations …

Simulation Analysis In Dynamic Performance Of Proton Exchange Membrane Fuel Cell Under Starting Condition, Yan Xiao, Ying-Jie Chang, Wei Zhang, Qiu-Hong Jia

Journal of Electrochemistry

Based on the equivalent circuit model, by considering both the dynamic gas pressure model and the dynamic heat transfer model, a lumped parameter model is developed. The start process of the fuel cell is simulated by using SIMULINK software. The undershoot of the voltage is observed from the simulation results, and the response time of the voltage is basically the same as that of the fuel cell temperature, which indicates that the temperature has great influence on the dynamic performance of the fuel cell. From the perspective of the temperature, the dynamic responses of the thermodynamic potential, the activation overvoltage, …

Interaction Between Energy And Electrocatalysis —— A Review On The 1st Young Scientist Forum On Energy Electrocatalysis, Hong Li, Wen-Bin Cai

Journal of Electrochemistry

No abstract provided.

Effects Of Rotating Magnetic Fields On Pem Fuel Cell Performance, Mao-Liang Wu, En-Ze Wang, Guang-De Pan, Zhong-Jun Liu, Fei Xie

Journal of Electrochemistry

Proton Exchange Membrane (PEM) fuel cell performance may be improved by application of additional magnetic fields. In this work, one square permanent magnet, made of either 16 combination cylinder magnets with homopolarity or 16 combination cylinder magnets with heteropolarity, was exerted on the fuel cell surface to produce additional magnetic field affecting PEM fuel cell performance. The influences of magnetic field status (rotating, static and none) on polarization and power density curves measured in a PEM fuel cell were investigated. The results verified the benefit of magnetic field, proving that the magnetic field distribution could improve the fuel cell output. …

Preparation Of Ni(Dpim)2Cl2 Complex For The Electrocatalytic Reduction Of Co2, Li-Pu Zhang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

A new Ni(dpim)₂Cl₂complex using 2-(diphenylphosphino)-1-methylimidazole (dpim) as ligand was prepared and served as a catalyst for the electrochemical reduction of CO₂. The electrochemical redox behavior of Ni(dpim)₂Cl₂ in CH₃CN/TPABF₄ solution under nitrogen atmosphere showed the two-electron irreversible reduction at -0.7 V and one-electron quasi-reversible reduction at -1.3 V. After bubbling CO₂ into the electrolyte, the reduction peak appeared at -1.3 V became irreversible and the peak current increased from 0.48 mA·cm^-2 to 0.55 mA·cm^-2. Moreover, the peak current at -1.3 V could further increase …

Preparation And Properties Of Manganese Oxide And Polyaniline-Carbon Composite Electrode, Tian-Tian Zhou, Bing Wu, Chao Deng, Ying Gao

Journal of Electrochemistry

The polyaniline-carbon (PAnC) electrode was prepared by the polymerization of aniline monomer and activated carbon in ice water bath, and followed by chemical deposition of manganese dioxide MnO₂-PAnC composite material. The specific capacitance of MnO₂-PAnC reached 459 F•g^-1. The cyclic voltammetric results showed a small deformation in the voltammogram curve obtained with the MnO₂-PAnC electrode at high scan rate, indicating good reversibility and capacitive properties. The AC impedance results revealed that the MnO₂-PAnC electrode displayed the smallest charge transfer resistance and the fastest diffusion
rate of surface ions than other …

In Situ Defect Detection Using Three Color Spectroscopy In Laser Powder Bed Additive Manufacturing, Andrew Drieling

The University Honors Program

Additive Manufacturing (AM) provides a way to create parts that would be extremely difficult or impossible with conventional manufacturing processes. However, AM also introduces defects, which are detrimental to the mechanical performance. These defects are potentially unknown until post-processing inspection and testing, wasting time and resources on an unusable part or initiating unexpected failure. Historically, spectroscopy has successfully been used for in situ monitoring of laser welding, using changing parameters in the generated plume to predict defects. In situ monitoring using a visible spectrometer for fabrication of Alloy 718 on a test bed laser powder bed fusion system is performed. …

Rare Earth - Free Permanent Magnetic Material, Laura H. Lewis, Jeffrey E. Shield, Katayun Barmak Viziri

Department of Mechanical and Materials Engineering: Faculty Publications

The invention provides rare earth - free permanent magnetic materials and methods of making them . The materials can be used to produce magnetic structures for use in a wide variety of commercial applications , such as motors , generators , and other electromechanical and electronic devices . Magnets fabricated using the materials can be substituted for magnets requiring rare earth elements that are costly and in limited supply . The invention provides two different types of magnetic materials . The first type is based on an iron - nickel alloy that is doped with one or more doping elements …

Method Of Fabricating A Continuous Nanofiber, Yuris Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

A method of fabricating a continuous nanofiber is described . The method includes preparing a solution of one or more polymers and one or more solvents and electrospinning the solution by discharging the solution through one or more liquid jets into an electric field to yield one or more continuous nanofibers . The electrospinning process ( i ) highly orients one or more polymer chains in the one or more continuous nanofibers along a fiber axis of the one or more continuous nanofibers , and ( ii ) suppresses polymer crystallization in the one or more continuous nanofibers . The …

Method For Data - Driven Learning - Based Control Of Hvac Systems Using High - Dimensional Sensory Observations, Amir-Massoud Farahmand, Saleh Nabi, Piyush Grover, Daniel Nikolaev Nikovski

Department of Mechanical and Materials Engineering: Faculty Publications

A controller for controlling an operation of an air - conditioning system conditioning an indoor space includes a data input to receive state data of the space at multiple points in the space , a memory to store a code of a reinforcement learning algorithm and a history of the state data and a history of control commands having been applied to the air - conditioning system , wherein the history of the control commands is associated with the state data and history of rewards , a processor coupled to the memory determines a value function outputting a cumulative value …

Review Of Challenges And Advances In Modification Of Food Package Headspace Gases, Ziynet Boz, Bruce A. Welt, Jeffrey K. Brecht, William Pelletier, Eric Mclamore, Gregory A. Kiker, Jason E. Butler

Journal of Applied Packaging Research

Modified Atmosphere Packaging (MAP) has been widely used as an effective way to preserve foods. Fresh produce, meat and meat products, seafood, and dairy products can benefit from modified gaseous atmospheres, which are usually achieved by reducing oxygen and increasing carbon dioxide concentrations, within limits, defined by product tolerances. MAP of fresh produce is particularly challenging because products are living and respiring. Respiration rates depend on several factors including temperature, oxygen, and carbon dioxide concentrations. Balancing package permeation with respiration is challenging, often due to limited selection of practical packaging materials. Failing to remain within tolerance limits of products leads …

An Evaluation Of Induction Heating In Healthcare Food Industry, Barrett Alexander Hampton

Masters Theses & Specialist Projects

This thesis addresses the problem healthcare facilities are having in maintaining proper food temperatures while transporting meals to patients after food has left the kitchen area. Induction heat has been a known method for generating heat for many years. The commercial food industry currently uses this technology, which is beginning to appear in the residential sector as well because of developments made by manufacturers. This study focuses on the top commercial brand models of induction heaters and the supporting materials currently used to create heat sources to maintain food temperatures in hospitals and long term care facilities.

The research in …

Experimental Investigation Of And Constitutive Model For The Thermo-Poro-Mechanical Deformation Of Granular Salt Under Hydrostatic Compression, Brandon C. Lampe

Civil Engineering ETDs

The influence of pore pressure and porosity on the ductile deformation of granular salt was experimentally investigated under hydrostatic compression. Confining and pore pressures were independently controlled while granular salt samples exhibited rate-dependent deformation that resulted in large decreases of sample volume and porosity. The sample deformation rates were observed to correspond with both the sample porosity and the pressure difference between the confining and pore pressures. Post-test observations revealed that the reduced porosity was caused by the solid particles deforming in a ductile manner. Insight into the cause of ductile deformation was gained by considering the local stress distribution …

Creep Of Hafnium Diboride -20 Vol% Silicon Carbide At 1500°C In Air, Glen E. Pry

Theses and Dissertations

Refractory metal borides, commonly referred to as Ultra High Temperature Ceramics (UHTCs), exhibit a number of unique properties, such as extremely high melting temperature and hardness, chemical stability, high electrical and thermal conductivity and corrosion resistance. It has been demonstrated that the addition of SiC improves the oxidation resistance of ZrB2- and HfB2-based UHTCs above 1200°C by modifying the composition of the oxide scale. Addition of SiC retards the oxidation rate of ZrB2 and HfB2 by forming a protective layer of borosilicate glass. Creep deformation is one of the critical criterion for structural application of ceramics at elevated temperatures. Compression …

Tensile Properties And Fatigue Behavior Of Geopolymer Matrix Composites With Carbon Fiber Reinforcement At Elevated Temperature, Steffan M.L. Wilcox

Theses and Dissertations

The tensile stress-strain and tension-tension fatigue of geopolymer matrix composites reinforced with 0/90 carbon fibers was investigated at 23 and 300°C in laboratory air. Geopolymers are inorganic polymeric materials composed of alumina, silica, and alkali metal oxides. Because geopolymers are synthesized as a fluid mixture or particles and liquid, they can be cast into a desired shape, and cured at only slightly elevated temperatures. The relative ease of synthesis and low processing temperatures make geopolymers an attractive choice as a matrix material for composite materials. Geopolymers also offer resistance to heat and oxidizing environments. Currently, geopolymer matrix composites are being …

Creep Of Nextel 720/A Ceramic Matrix Composite With Laser Drilled Effusion Holes At 1200°C In Air And In Steam, Savannah N. Minor

Theses and Dissertations

Creep behavior of an oxide-oxide ceramic matrix composite (CMC) containing an array of effusion holes was investigated at 1200⁰C in air and in steam. The composite (N720/A) consisted of a porous alumina matrix reinforced with alumina-mullite NextelTM 720 fibers. Test specimens had an array of 17 effusion holes with 0.5-mm diameter. The effusion holes were drilled through the specimen thickness normal to the specimen surface using a CO2 laser. Effect of the effusion holes on tensile properties was evaluated tension tests to failure at 1200°C in air. Creep of specimens with effusion holes at 1200°C was studied for creep stresses …

Influence Of Coolant Flow Rate Parameters In Scaling Gas Turbine Cooling Effectiveness On A Flat Plate, Jacob P. Fischer

Theses and Dissertations

Effective film cooling relies on the performance of the selected cooling hole shape and placement of the holes on the surface of the blade. To test each holes effectiveness, large scale, low-temperature testing has been used to reduce cost and complexity. The resulting quantity from this testing is called the adiabatic effectiveness (n). The adiabatic effectiveness can then scaled up to engine operating conditions to predict how the selected film cooling hole will perform. This process is complicated by the nonlinear variation of gas properties between coolant and freestream conditions as well as between the experimental and engine conditions. In …

The Effect Of Poly (Glycerol Sebacate) Incorporation Within Hybrid Chitin–Lignin Sol–Gel Nanofibrous Scaffolds, Tuerdimaimaiti Abudula, Lassaad Gzara, Giovanna Simonetti, Ahmed Alshahrie, Numan Salah, Pierfrancesco Morganti, Angelo Chianese, Afsoon Fallahi, Ali Tamayol, Sidi A. Bencherif, Adnan Memic

Department of Mechanical and Materials Engineering: Faculty Publications

Chitin and lignin primarily accumulate as bio-waste resulting from byproducts of crustacean crusts and plant biomass. Recently, their use has been proposed for diverse and unique bioengineering applications, amongst others. However, their weak mechanical properties need to be improved in order to facilitate their industrial utilization. In this paper, we fabricated hybrid fibers composed of a chitin–lignin (CL)-based sol–gel mixture and elastomeric poly (glycerol sebacate) (PGS) using a standard electrospinning approach. Obtained results showed that PGS could be coherently blended with the sol–gel mixture to form a nanofibrous scaffold exhibiting remarkable mechanical performance and improved antibacterial and antifungal activity. The …

Improvement Of The Material's Mechanical Characteristics Using Intelligent Real Time Control Interfaces In Hfc Hardening Process, Florentin Smarandache, Luige Vladareanu, Mihaiela Iliescu, Victor Vladareanu, Alexandru Gal, Octavian Melinte, Adrian Margean

Branch Mathematics and Statistics Faculty and Staff Publications

The paper presents Intelligent Control (IC) Interfaces for real time control of mechatronic systems applied to Hardening Process Control (HPC) in order to improvement of the material's mechanical characteristics. Implementation of IC laws in the intelligent real time control interfaces depends on the particular circumstances of the models characteristics used and the exact definition of optimization problem. The results led to the development of the IC interfaces in real time through Particle Swarm Optimization (PSO) and neural networks (NN) using offline the regression methods.

A Survey On Network Security-Related Data Collection Technologies, Huaqing Lin, Zheng Yan, Yu Chen, Lifang Zhang

Faculty Publications, Information Systems & Technology

Security threats and economic loss caused by network attacks, intrusions, and vulnerabilities have motivated intensive studies on network security. Normally, data collected in a network system can reflect or can be used to detect security threats. We define these data as network security-related data. Studying and analyzing security-related data can help detect network attacks and intrusions, thus making it possible to further measure the security level of the whole network system. Obviously, the first step in detecting network attacks and intrusions is to collect security-related data. However, in the context of big data and 5G, there exist a number of …

Me-Em Enewsbrief, March 2018, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

The Positive Role Of Curcumin-Loaded Salmon Nanoliposomes On The Culture Of Primary Cortical Neurons, Mahmoud Hasan, Shahrzad Latifi, Cyril J.F. Kahn, Ali Tamayol, Rouhollah Habibey, Elodie Passeri, Michel Linder, Elmira Arab-Tehrany

Department of Mechanical and Materials Engineering: Faculty Publications

Curcumin (diferuloylmethane) is a natural bioactive compound with many health-promoting benefits. However, its poor water solubility and bioavailability has limited curcumin’s biomedical application. In the present study, we encapsulated curcumin into liposomes, formed from natural sources (salmon lecithin), and characterized its encapsulation efficiency and release profile. The proposed natural carriers increased the solubility and the bioavailability of curcumin. In addition, various physico-chemical properties of the developed soft nanocarriers with and without curcumin were studied. Nanoliposome-encapsulated curcumin increased the viability and network formation in the culture of primary cortical neurons and decreased the rate of apoptosis.

Preparation And Characterization Of Titanate-Phosphate Passivation Film On Tinplate, Zi-Yu Wang, Ming-Hao Wang, De-Yu Li, Ning Li

Journal of Electrochemistry

A passivation film was prepared on tinplate surface with a composite passivating agent made of titanate and phosphate. The surface morphologies, chemical compositions and corrosion resistances of the passivation films were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), salt spray test, Tafel polarization measurement and electrochemical impedance spectroscopy (EIS). The results were compared with those films untreated and treated with titanate or phosphate passivation. It was shown that the titanate and phosphate passivation film was mainly composed of Ti₃(PO₄)₄·nH₂O and TiO₂. The finely crystallized surface could seal …

Preparation And Properties Of Nanocrystalline Nickel By Pulse Electrodeposition On Glassy Carbon, Ya-Li Zhang, Ming-Xian Zhang, Teng-Da Guo, Yan-Jie Zhao, Sheng-Xue Yu

Journal of Electrochemistry

Nanocrystalline nickel exhibits electrocatalytic activity for methanol. In this work, nanocrystalline nickel coating has been obtained by using the double pulse method on glassy carbon materials surface. The influence of pulse conditions on the grain size of nanocrystalline nicke was studied. The concentrations and compositions of the plating bath were  300 g·L^-1 NiSO₄·6H₂O,45 g·L^-1 NiCl₂·6H₂O,40 g·L^-1 H₃BO₃,5 g·L^-1 C₇H₅NO₃S,and 0.05 g·L^-1 C₁₂H₂₅NaO₄S. The optimal pulse process parameters including the average pulse …

Synthesis And Electrochemical Properties Of Nickel-Rich Cathode Material Lini0.6Co0.2Mn0.2O2 With High Initial Coulombic Efficiency, Xiao-Yun Guan, Chao-Yu Hong, Jian-Ping Zhu, Wei-Li Wang, Yi-Xiao Li, Yong Yang

Journal of Electrochemistry

Nickel-rich cathode materials LiNi_0.6Co_0.2Mn_0.2O₂(NCM622)were synthesized by a co-precipitation-solid state sintering method at different temperatures. The structure, morphology and electrochemical performance of the as-prepared materials were investigated by X-ray powder diffraction (XRD) /Rietveld refinement, scanning electron microscope (SEM) and electrochemical experiments. It is found that NCM622 calcined at 800 ℃ showed the lowest degree of cation disorder (~1.97%) with a high initial Coulombic effiency of 92.2% and the capacity retention of 81.4% after 100 cycles.

Electrodeposition Of Cigs Thin Film With Special Structure Using Laser Etching Template, Jin-Zhi Yu, Ye Lian, Jin-Qiu Zhang, Pei-Xia Yang, Mao-Zhong An

Journal of Electrochemistry

Copper indium gallium selenide (Cu_1.00In_xGa_1-xSe_2.00, CIGS) thin film solar cells have a wide application in semiconductor thin film batteries. The CIGS absorbing layer is the key of the thin film solar cell material. Therefore, it is of theoretical and practical significance to carry out researches in CIGS thin films. In this work, the CIGS thin films with special structures were prepared by using laser etching template. The copper thin film was firstly electrodeposited in aqueous solution with Laser etching template. The influences of temperature, current and concentration of copper sulfate on morphology …

Superhydrophobic Surface On Aluminum Alloy By Hydrothermal Method And Its Electrochemical Performance, Xiao-Hang Chen, Mo-Jing Chen, Yu-Lin Min, Qun-Jie Xu

Journal of Electrochemistry

Superhydrophobic film formed on a metal surface is an effective way for corrosion protection. In this paper, the superhydrophobic film was prepared on the surfaces of aluminum alloy by hydrothermally treating with a solution containing CeCl₃·7H₂O and CO(NH₂)₂ , and a self-assemble process. The electrochemical measurements and surface morphology results confirmed that the best superhydrophobicity and electrochemical performance could be achieved with the contact angle of 155.5^o after six hours of hydrothermal reaction. Furthermore, the inhibition efficiency of 99.6% was obtained in 3.5 wt% NaCl aqueous solution, indicating the excellent corrosion resistance …