Engineering Science and Materials Commons^™

Recent Progress In Solid-State Nmr Study Of Electrode/Electrolyte Materials For Lithium/Sodium Ion Batteries, Gui-Ming Zhong, Zi-Geng Liu, Da-Wei Wang, Qi Li, Ri-Qiang Fu, Yong Yang

Journal of Electrochemistry

Solid state NMR technique is a powerful tool for characterizing the local structure and compositions of solid materials quantitatively. A comprehensive understanding of the structure evolution during the electrochemical reactions of the materials for lithium/sodium ion batteries will be obtained with the combination of solid state NMR, XRD, and XAS methods. Through analyzing solid state NMR spectra, we can obtain the compositions, local structures and ion diffusion dynamics of electrodes, electrolytes and surface layers for lithium/sodium ion batteries, providing an important theoretical support for the design and development of high-performance materials for batteries. In this paper, we review the recent …

3, 4-Ethylenedioxythiophene Monomer As Safety-Enhancing Additive For Lithium Ion Batteries, Wei-Xiao Ji, Feng Wang, Jiang-Feng Qian, Yu-Liang Cao, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

Safety concern is a major obstacle hindering the wide applications of large-capacity lithium ion batteries (LIBs) in electric vehicles. In this paper, a polymerizable monomer of 3, 4-ethylenedioxythiophene (EDOT) was proposed and tested as an electrolyte additive for enhancing the safety of LIBs. The electro-oxidative polymerization behaviors and influence of PEDOT additive on the thermal behavior of LiCoO₂ cathode, as well as the safety performance and electrochemical properties of LiCoO₂-based LIBs were investigated. The results from cyclic voltammetry (CV) and transmission electron microscope (TEM) characterizations indicated that the monomer additive can be electro-oxidatively polymerized to form a …

Reduced Graphene Oxide (Rgo) Hollow Network Cages For High-Performance Electrochemical Energy Storage, Chi Zhang, Xu-Jun He, Gao-Ren Li

Journal of Electrochemistry

The reduced graphese oxide (RGO) hollow network cages were synthesized via zinc oxide (ZnO) template-assisted electrodeposition. The as-prepared RGO hollow network cages exhibited the multi-level architectures, from nano sheets, porous structures, networks, to 3D microscaled hollow cages, which can simultaneously optimize transport of electroactive species, utilization rate of electrode material, and super capacitive performance. Electrochemical measurements confirmed the superior performance of RGO hollow network cages for supercapacitors (SCs), such as high Csp (393 F⋅g^-1 at 1.0 A⋅g^-1), excellent rate capability (21.2% Csp loss from 1.0 to 20 A⋅g^-1), and superior cycling stability (< 1% Csp loss after 10000 cycles).

Developments Of Photo-Assisted Fuel Cells, Ling-Ling Zhang, Shao-Jun Dong

Journal of Electrochemistry

The exploitation and utilization of fossil fuels have led to serious energy crisis and environmental pollution. In this case, the development of renewable energy is an alternative to traditional energy consumption. Fuel cells (FCs) can convert chemical energy into electricity via the electrochemical reaction, which is green and environment-friendly. Photo-assisted FCs integrate photo-responsive components into FCs, leading to the dual routes of energy conversion including light energy to electricity and chemical energy to electricity, and thus, improving the energy utilization efficiency. The development of photo-assisted FCs is significant for practical application and promising to solve the coming energy crisis. In …

Effects Of Electrode Off Centre On Trapped Thickness-Shear Modes In Contoured At-Cut Quartz Resonators, Junjie Shi, Cuiying Fan, Minghao Zhao, Jiashi S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We investigated thickness-shear vibrations of a contoured, AT-cut quartz resonator with a pair of electrodes displaced from the resonator centre. The scalar differential equations by Stevens and Tiersten for thickness-shear vibrations of electroded and unelectroded quartz plates were employed. Based on the variational formulation of the scalar differential equations established in a previous paper and the variation-based Ritz method with trigonometric functions as basis functions, free vibration resonance frequencies and trapped thickness-shear modes were obtained. The effects of the electrode off centre on resonance frequencies and mode shapes were examined. When the electrode off centre is about one hundredth of …

Floquet Topological Insulators For Sound, Romain Fleury, Alexander B. Khanikaev, Andrea Alu

Publications and Research

The unique conduction properties of condensed matter systems with topological order have recently inspired a quest for the similar effects in classical wave phenomena. Acoustic topological insulators, in particular, hold the promise to revolutionize our ability to control sound, allowing for large isolation in the bulk and broadband one-way transport along their edges, with topological immunity against structural defects and disorder. So far, these fascinating properties have been obtained relying on moving media, which may introduce noise and absorption losses, hindering the practical potential of topological acoustics. Here we overcome these limitations by modulating in time the acoustic properties of …

Biomimetic Seal Flipper Test Rig, Gordon D. Belyea, Laura Kawashiri, Dylan Rinker, Kurt Beske

Mechanical Engineering

No abstract provided.

Development And Evaluation Of Matrix Material Formulations For Potential Integration Into Immunodiagnostic Biosensors, Payam Aminayi

Dissertations

This study supports the development, characterization and optimization of biosensor material formulations for immunodiagnostic applications based on experimental findings and hypotheses by Wang and Wu [1, 2], and using a test-plate apparatus and thin-film design developed by Young [3].

Certain biosensors working on the basis of conductance/impedance changes have demonstrated their potential to detect various bacteria, enzymes, and biomolecules due to their enhanced electrical properties with incorporated single-walled carbon nanotubes (SWNT). From the work conducted in our laboratory, we are attempting to determine and develop a matrix formulation containing highly dispersed SWNT, antibody and other components that elicit a significantly …

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Carbon Fiber Reinforced Polymer Roofing At Ac2 Auditorium: A Case Study, Jacob R. Hague

Construction Management

Carbon Fiber Reinforced Polymer (CFRP) has been used in several capacities in the manufacturing of products such as high performance cars and airplanes, as well as many other smaller products. In construction, it has primarily been used as a way to strengthen or repair existing structures, and in some more recent applications, in tension cables. This paper will examine a new way to use CFRP- as a roofing material, and will specifically focus on the design and installation of a CFRP roof installed at Apple’s new AC2 Auditorium, forming the roof for the main entrance lobby. Installed in February of …

Light-Activated Photocurrent Degradation And Self-Healing In Perovskite Solar Cells, Wanyi Nie, Jean-Christophe Blancon, Amanda J. Neukirch, Kannatassen Appavoo, Hsinhan Tsai, Manish Chhowalla, Muhammad A. Alam, Matthew Y. Sfeir, Claudine Katan, Jacky Even, Sergei Tretiak, Jared J. Crochet, Gautam Gupta, Aditya D. Mohite

Publications and Research

Solution-processed organometallic perovskite solar cells have emerged as one of the most promising thin-film photovoltaic technology. However, a key challenge is their lack of stability over prolonged solar irradiation. Few studies have investigated the effect of light soaking on hybrid perovskites and have attributed the degradation in the optoelectronic properties to photochemical or field-assisted ion migration. Here we show that the slow photocurrent degradation in thin-film photovoltaic devices is due to the formation of light-activated meta-stable deep-level trap states. However, the devices can self-heal completely by resting them in the dark for <1 min or the degradation can be completely prevented by operating the devices at 0°C. We investigate several physical mechanisms to explain the microscopic origin for the formation of these trap states, among which the creation of small polaronic states involving localized cooperative lattice strain and molecular orientations emerges as a credible microscopic mechanism requiring further detailed studies.

Theory Of Carrier Transport From First Principles: Applications In Photovoltaic And Thermoelectric Materials, Alireza Faghaninia

McKelvey School of Engineering Graduate Student Theses & Dissertations

New sources of energy that are environmentally friendly, cost-effective, and renewable are essential if we are to combat the effects of global climate change. Two of these sources are solar photovoltaic (PV) cells to convert sunlight into electricity and thermoelectric (TE) devices to convert heat to electricity. To be practical on a large scale, the properties (e.g. electrical conductivity, band gap, Seebeck coefficient, etc) of the the underlying materials must be improved significantly through judicious control of structure and composition. Significant understanding of materials properties is required to design and engineer new high-performing materials. First principles calculations using density functional …

Focal Adhesion Kinase Regulation In Stem Cell Alignment And Spreading On Nanofibers, Mohammad Nahid Andalib, Jeong Soon Lee, Ligyeom Ha, Yuris A. Dzenis, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

While electrospun nanofibers have demonstrated the potential for novel tissue engineering scaffolds, very little is known about the molecular mechanism of how cells sense and adapt to nanofibers. Here, we revealed the role of focal adhesion kinase (FAK), one of the key molecular sensors in the focal adhesion complex, in regulating mesenchymal stem cell (MSC) shaping on nanofibers. We produced uniaxially aligned and randomly distributed nanofibers from poly(L-lactic acid) to have the same diameters (about 130 nm) and evaluated MSC behavior on these nanofibers comparing with that on flat PLLA control. C3H10T1/2 murine MSCs exhibited upregulations in FAK expression and …

Haul Truck Tires Recycling, Jessica N. Lizarazu

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers. These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months. Statistics regarding discarded OTR tires are not provided by the …

Impedance Spectroscopy Studies Of Yttria Stabilized Zirconia Under Extreme Conditions, Quinlan Blaine Smith

UNLV Theses, Dissertations, Professional Papers, and Capstones

Yttria Stabilized Zirconia (YSZ) is of interest for many industries. Varying amounts of Yttria (Y2O3) can be doped into Zirconia (ZrO2) to create materials with specific characteristics. For instance, 3mol% YSZ (3YSZ) is known to be a super hard material and is used as a coating on drill tips and as an abrasive. Eight mol% YSZ (8YSZ) is commonly used as a solid electrolyte in Solid Oxide Fuel Cells because of its good ionic conducting abilities and stability at high temperatures. In this thesis project, a novel experimental setup was created and used to study the ionic conductivity of (3 …

Nanoscale Frictional Properties Of Nickel With One-Dimensional And Two-Dimensional Materials, Timothy K. Schlenger

Mechanical Engineering Undergraduate Honors Theses

When looking at the nanoscale, material interface interactions have been observed to exhibit particularly interesting properties. Our research looks into various combinations of carbyne and graphene atop a nickel block to look into the interface friction properties between them. Both the carbyne and graphene are tested using steered molecular dynamics (SMD) in sheering and peeling directions along the surface of the nickel block. These tests are then analyzed by comparing the magnitude of the acting force versus the displacement of the carbon allotrope sample across the nickel block. It is found that as the width of a carbon allotrope sample …

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …

Design Of A Folding V-Scraper With Roller For Orchard Applications, Chase Ulrich

BioResource and Agricultural Engineering

This senior project discusses the design of a folding 15 ft. wide leveler for orchard use. This design utilized a category 2 three-point hitch to connect the implement to a tractor. The folding mechanism uses the tractors hydraulic system to actuate the folding movement using hydraulic cylinders. The blades, when wings in operational position, are rigid with one another after some assembly. When the implement is folded the width is reduced to nine feet.

Stabilization Of Vegetable Oil-Based Quenchants To Thermal-Oxidative Degradation: Experimental Strategy And Effect Of Oxidation On Quenching Performance, Éder Cícero Adão Simêncio, Rosa Lúcia Simêncio Otero, Lauralice De Campos Franceschini Canale, George E. Totten

Mechanical and Materials Engineering Faculty Publications and Presentations

Although petroleum oils continue to be the dominant type of basestock for the formulation of vaporizable quenchants, there is increasing pressure to identify an alternative basestock to address the limitations to their continued use because they are not a renewable basestock and they possess generally poor toxicity and biodegradability properties. Currently the most often cited alternative basestocks are those based on seed oils since they are renewable and usually non-toxic but especially because they are typically readily biodegradable. However, they suffer a critically important deficiency in that they are also typically much less stable to thermal-oxidative degradation than petroleum oils. …

Effect Of Thermal Treatment On High Temperature Deformation Of Alloy Ep-~823, Martin Milburn Lewis

UNLV Theses, Dissertations, Professional Papers, and Capstones

The objective of this research topic is to determine mechanical properties of Alloy EP-823 and to provide a mechanistic understanding of its sensitivity to both thermal treatment and performance temperature. EP-823 is a leading target material for accelerator-driven waste transmutation applications. Overall, the tensile test results of Alloy EP-823 indicated a general trend of decreasing mechanical performance with an increase in tempering time. An increase in tempering time had a statistically significant inverse relationship with ultimate tensile strength (UTS) and yield strength (YS). An increase in tempering time did not have a significant effect on elongation and reduction in area. …

High-Pressure Properties Of Several Narrow Bandgap Semiconductors From First-Principles Calculations, Andrew Michael Alvarado

UNLV Theses, Dissertations, Professional Papers, and Capstones

The electronic, thermodynamic, and structural properties of three semiconducting materials, ZnO, InN, and PbS, at high pressure are investigated utilizing first-principles calculations based on density function theory. The first two systems, ZnO and InN, crystalize as hexagonal structures at ambient conditions and transition to a cubic structure at higher pressures. The last system, PbS, is cubic at ambient conditions, but transitions to an orthorhombic structure at higher pressure. At ambient conditions, these materials are well known semiconductors with vast amount of research and a variety of wide ranging applications in electrical devices. However, there is a lack of understanding of …

Preparation And Performance Of 3d Graphene Type Porous Carbon Employing Nano Fe(Oh)3 As Template For Oxygen Reduction Catalyst, Chong-Yun Sun, Zhong-Fang Li, Xue-Wei Lu, Xi-Zhan Zhong, Yu-Rong Liu

Journal of Electrochemistry

The 3D graphene type porous carbon was prepared using coal tar pitch as carbon source and nano Fe(OH)₃ as template. Optimal conditions for the catalytic oxygen reduction performance were determined as: the mass ratio of coal tar, nano Fe(OH)₃ and KOH is 6:8:4; the pyrolysis temperature is 800 ^oC. SEM images show that the products have uniformly porous structure. TEM images demonstrate that the products are porous with foam shapes. HRTEM images further indicate that the products have formed several-layers 3D graphene structure, which are also supported by XRD and Raman data, and the pore size mainly …

Special Issue: Electrocatalyst And Electrocatalysis In Fuel Cells Preface, Zi-Dong Wei

Journal of Electrochemistry

/

Recent Progress In Non-Precious Metal Oxygen Reduction Reaction Catalysts With An Encapsulation Structure, Mei-Ling Xiao, Jian-Bing Zhu, Chang-Peng Liu, Jun-Jie Ge, Wei Xing

Journal of Electrochemistry

Platinum-based materials, the state-of-the-art catalysts for fuel cells, suffer from prohibitive costs, limited resources and insufficient durability. Accordingly, tremendous efforts were made in searching for efficient, durable and inexpensive alternatives to precious-metal electrocatalysts for the oxygen reduction reaction (ORR). Transition-metals (Fe, Co)/nitrogen co-doped hybrids, heteroatom (N, P, S, F, et al) doped carbons and composites with transition-metals encapsulated in graphitic layers are reported as the most efficient non-precious metal ORR catalysts. Among the various non-precious metal ORR catalysts, transition-metals encased in graphitic layer catalysts are a novel type of catalysts for ORR with high activity and durability, and thus, the …

Mini-Review: Possible Applications Of Scanning Electrochemical Microscopy (Secm) In Characterizations Of Oxygen Reduction Reaction And Oxygen Evolution Reaction, Xing-Xing Chen

Journal of Electrochemistry

Scanning electrochemical microscopy (SECM) has been proved to be a unique technique for combinatorial screening of localized phenomena for different electrocatalysts potentially used in new energy conversion and storage systems. This mini-review provides a brief summary of different SECM working modes, such as direct mode, feedback mode, generation-collection mode, redox competition mode and noise mode, which are especially applied for characterizing the oxygen reactions. Particularly, a series of important development in SECM screening of electrocatalysts for oxygen reduction reaction and oxygen evolution reaction from the author and W. Schuhmann’s group in Germany has been highlighted and overviewed. Finally, some prospects …

Multi-Scaled Carbon Supported Platinum As A Stable Electrocatalyst For Oxygen Reduction Reaction, Yu-Ping Li, Lu-Hua Jiang, Su-Li Wang, Gong-Quan Sun

Journal of Electrochemistry

The stability of carbon supports is essential for electrocatalysts of fuel cells. Herein, the mesoporous carbon with the high graphitic degree (highly graphitic mesoporous carbon, HGMC) was synthesized by using resorcinol as the carbon precursor, SiO₂ as the templates and urea as the reducing agent. The as-prepared HGMC was characterized by XRD, Raman spectroscopy, TEM, N2 adsorption. The stability of HGMC was evaluated by mimicking the start-up/shut-down conditions of fuel cells in a three-electrode system referring to the NREL standard. The obtained HGMC is of moderate surface area (187.4 m²•g^-1) and is chemically stable under …

Recycling Mf Solid Waste Into Mesoporous Nitrogen-Doped Carbon With Iron Carbide Complex In Graphitic Layers As An Efficient Catalyst For Oxygen Reduction Reaction, Can-Yun Zhao, Lin Huang, Yong You, Ying-Fang Yao, Xiao-Gang Su, Hong Wan, Jian-Guo Liu, Cong-Ping Wu

Journal of Electrochemistry

Nitrogen-doped carbon materials with iron ions are known as catalytic growth agents for the oxygen reduction reaction (ORR) in fuel cells, but the design and synthesis of high-performance and low-cost catalysts still remain a significant challenge. Herein, we present a cost-effective approach to dispose of MF solid waste as the precursor for the synthesis of MCFes catalyst with the favorable structure features such as the high specific surface area, abundant active sites and suitable pore structure. The results showed that the MCFe-10/10/2 had specific surface area as high as 780.7 m²•g^-1 and high efficient catalytic activity comparable …

Recent Progresses In Molybdenum-Based Electrocatalysts For The Hydrogen Evolution Reaction, Ze-Xing Wu, Jie Wang, Jun-Po Guo, Jing Zhu, De-Li Wang

Journal of Electrochemistry

Electrochemical catalytic production of hydrogen has been considered as a promising and sustainable strategy for clean and renewable energy technologies. Molybdenum-based non noble metal catalysts for the hydrogen evolution reaction have attracted extensive attention due to its effective catalytic performance. In this review, the recent progresses in molybdenum-carbide, phosphide, nitride and sulfide electrocatalysts are presented. In addition, the strategies to improve the catalytic performance are analyzed and the prospects for the future development trends are expected.

Syntheses Of Carbon Paper Supported High-Index Faceted Pt Nanoparticles And Their Performance In Direct Formic Acid Fuel Cells, Long Huang, Mei Zhan, Yu-Cheng Wang, Yan-Fen Lin, Shuo Liu, Ting Yuan, Hui Yang, Shi-Gang Sun

Journal of Electrochemistry

Direct formic acid fuel fuels (DFAFCs) are promising energy source for portable electronic devices. Palladium (Pd) is more active than platinum (Pt) for the formic acid electrooxidation. However, the stability of Pd is much poorer than that of Pt. Unfortunately, the ultra-low natural abundance of the Pt makes it extremely expensive and limits its application as a fuel cell catalyst. Boosting both the activity and stability of Pt nanoparticles to enhance their efficiency is urgent. As previous works illustrated, nanoparticles enclosed with high-index facets usually bare a higher activity toward fuel cell related reactions than those nanoparticles with low-index facet. …

Dynamic Simulation Of Oxygen Reduction Reaction In Pt/C Electrode For Proton Exchange Membrane Fuel Cells, Shang Li, Fen Zhou, Lei Chen, Mu Pan

Journal of Electrochemistry

It is an urgent need to reduce the Pt loading in electrode for practical fuel cell applications worldwide. Herein, we theoretically investigate the oxygen distribution, generated current, and minimum Pt loading of Pt/C electrode for practical applications based on kinetic model of oxygen reduction reaction. The results indicate that with increasing electrode effective thickness to 40 mm, serious concentration polarization is expected for Pt/C electrode. To generate a power density of 1.4 W⋅cm^-2 (2.1A⋅cm^-2@0.67 V) for fuel cell, the cathode catalyst layer thickness in PEMFC should be as thin as 3 mm. The minimum Pt loading will …