Engineering Science and Materials Commons^™

Syntheses And Electrochemical Performances Of Li4Ti5O12 Anode Materials For Lithium Ion Battery, Yong-Long Zhang, Xue-Bu Hu, Yao-Qiong Wang, Dong-Hai Huang

Journal of Electrochemistry

Series of spinel lithium titanate (Li₄Ti₅O₁₂) materials were synthesized by one-step solid-state reaction using lithium acetate and TiO₂ as raw materials under different temperatures (750/800/850 °C) and atmospheres (N₂/air). The as-prepared Li₄Ti₅O₁₂ materials were investigated by thermogravimetric analysis, X-ray diffraction, scanning electron microscopy, cyclic voltammotry and charge-discharge test to analyze their crystal structures, microstructures and electrochemical performances. The results show that the Li₄Ti₅O₁₂（L-800N）material obtained at 800 °C under nitrogen atmosphere exhibited better electrochemical performance and smaller particle size. The initial …

A Platinum-Hydrogen Reference Micro-Electrode For All Vanadium Redox Flow Battery, Zhi-Bin Lin, Yan-Qing Dong, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

A platinum-hydrogen reference micro-electrode was made with electroplating Pd on the surface of Pt wire and then coating anion membrane material. This reference electrode was built-in the porous electrode of the all vanadium redox flow batteries (VRFB), and monitored the charging /discharging and self-discharging of the VRFB. The results indicated that the capacity fading of VRFB occurred due to the graduate reduction of V(IV) active species in the electrolyte and the accumulation of V(V) in the positive electrode, leading to nonequilibrium of active species between the positive and negative electrodes.

Electrochemical Conversion Reactions And Their Applications For Rechargeable Batteries, Ting Li, Han-Xi Yang

Journal of Electrochemistry

Electrochemical conversion reactions have received considerable interest as a new redox mechanism for constructing high capacity electrodes of rechargeable batteries. Without strict restrictions on the crystalline structure of the host lattice and the size of the associated ions, conversion reactions can take place in a variety of different metal compounds with different metal cations and deliver much higher reversible capacities through full utilization of all the oxidation states of the transition-metal compounds, opening up a new avenue for developing high capacity materials of rechargeable batteries. This paper briefly reviews the state of the art and challenges of conversion electrodes and …

Local Control Robotic Surgical Devices And Related Methods, Eric Markvicka, Tom Frederick, Jack Mondry, Joe Bartels, Shane Farritor

Department of Mechanical and Materials Engineering: Faculty Publications

The various robotic medical devices include robotic devices that are disposed within a body cavity and positioned using a support component disposed through an orifice or opening in the body cavity. Additional embodiments relate to devices having arms coupled to a device body wherein the device has a minimal profile such that the device can be easily inserted through smaller incisions in comparison to other devices without such a small profile. Further embodiments relate to methods of operating the above devices.

Fluids Dynamics & Heat Transfer Lab Design, Bruce Gerry

Thinking Matters Symposium Archive

This project consists of the designing, building, and creation of instruction manuals for several labs in fluids and heat transfer fields. Labs for these fields tend to be large and hard to simulate as physical models. This project will solve that problem by creating simulations: in solidworks. Not only will simulations in solidworks make some concepts possible to demonstrate but, it will also expose students to useful software that will be used in the workforce.

Intensity And Resolution Enhancement Of Local Regions For Object Detection And Tracking In Wide Area Surveillance, Evan Krieger, Vijayan K. Asari, Saibabu Arigela, Theus H. Aspiras

Electrical and Computer Engineering Faculty Publications

Object tracking in wide area motion imagery is a complex problem that consists of object detection and target tracking over time. This challenge can be solved by human analysts who naturally have the ability to keep track of an object in a scene. A computer vision solution for object tracking has the potential to be a much faster and efficient solution. However, a computer vision solution faces certain challenges that do not affect a human analyst. To overcome these challenges, a tracking process is proposed that is inspired by the known advantages of a human analyst.

First, the focus of …

An Operational Performance And Safety Comparison Of Roundabouts Vs. Traditional Intersections, Vincent Spahr

Honors Theses

As the modern roundabout becomes a more popular intersection alternative in the United States, the ability of the roundabout to effectively manage traffic and to do so safely is on the forefront of engineering concerns. Despite decades of international success and credibility, regions throughout the U.S. have been hesitant to implement roundabouts in place of more traditional intersections. This case study of a series of intersections in Dublin, OH assesses the operational performance of roundabouts as it compares to that of their stop-controlled and signalized counterparts and analyzes historical crash data to evaluate the safety of the various intersection types. …

A Microscopic Study On The Corrosion Fatigue Of Ultra-Fine Grained And Conventional Al–Mg Alloy, Mala M. Sharma, Josh D. Tomedi, Jeffery M. Parks

Faculty Journal Articles

The corrosion behavior of a nanocrystalline (NC)/ultrafine grained (UFG) Al–Mg based alloy was investigated and compared to its conventional counterpart 5083(H111). The corrosion fatigue (CF) was studied with respect to pit initiation, pit location and crack propagation as a function of environment. Scanning electron microscopy (SEM) with EDS was used to analyze the fracture surface of the failed specimen with respect to pitting characteristics, crack propagation and corrosion product. Load vs. cycles to failure was measured and S/N curves were generated for the UFG Al–Mg based alloy and the conventional counterpart 5083 in air and seawater.

Implications Of Heterogeneity In The Shock Wave Propagation Of Dynamically Shocked Materials, Jeffrey W. Lajeunesse

Master's Theses (2009 -)

The field of shock physics as a whole has only recently begun to pay particular attention to modeling heterogeneous materials under shock loading. These materials are important because of their practicality in terms of creating stronger, more shock resistant materials. To understand why they absorb shock impact energy better than homogeneous materials means that the small-scale processes that occur during the shock loading of these heterogeneous materials needs to be understood. Recent computational experiments, called mesoscale simulations, have shown that explicitly incorporating small-scale heterogeneous features into hydrocode simulations allows the bulk shock response of the heterogeneous material to be observed …

Methods And Systems For Handling Or Delivering Materials For Natural Orifice Surgery, Carl Nelson, Jeff Midday, Dimitry Oleynikov, Alan Goyzueta

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical systems, including systems that can be used in conjunction with medical devices used in endoscopic surgery. Certain embodiments include various material handling devices that can transport materials between the inside and the outside of an endoscopic surgery patient.

Me-Em Enewsbrief, March 2015, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Electrochemical Monitoring Of Cell Wall-Regulated Transient Extracellular Oxidative Burst From Single Plant Cells, Jun-Tao Liu, Yan-Ling Liu, Zhi Cheng, Shi-Jing Chen, Wei-Hua Huang

Journal of Electrochemistry

Oxidative burst by rapid, transient generation of reactive oxygen species (ROS) is a fundamental process for plant disease defense and signal transduction. ROS can be protective or toxic depending on their concentrations, and critical balance between ROS production and scavenging is regulated by complex and perfect mechanisms in plant cells. However, the process of rapid and transient ROS burst from plant cells and their regulatory mechanisms are far from being completely understood, owing to the methodological obstacles in real-time monitoring such a fast process. In this work, we showed the application of microelectrode electrochemistry with high spatiotemporal resolution to monitor …

A Novel Nitrite Sensing Electrode Based On Au/Fe3O4/Chitosan Nanocomposite, Ying Dong, Yong Wang, Huan-Huan Xing, Jian-Ying Qu

Journal of Electrochemistry

A novel nitrite sensing electrode based on gold nanoparticles and iron oxides (Fe₃O₄) magnetic nanoparticles was fabricated with chitosan as the protective film on glassy carbon matrix. Experiment results showed that the sensing electrode exhibited good electrocatalytic activity toward oxidation of nitrite, and the oxidation peak current increased linearly with the concentration of nitrite varying from 5.0×10^-6 to 2.0×10^-3 mol·L^-1 (R=0.9996) with a detection limit of 7.1×10^-7 mol·L^-1 (S/N=3). The sensing electrode exhibited good sensitivity, selectivity and repeatability.

Electrochemiluminescence Assay Based On Bipolar Electrode For Bioanalysis, Mei-Sheng Wu, Jing-Juan Xu, Hong-Yuan Chen

Journal of Electrochemistry

Bipolar electrodes (BPEs) are electronic conductors which are usually embedded into microchannels. The potential difference at the BPE/solution interface is obtained by applying a voltage at the two ends of the microchannel. When it reaches a critical value, the redox reaction takes place at both poles of the BPE simultaneously. Compared with other detection methods, the electrochemiluminescence (ECL) platform based on BPE possesses the advantages of concentration enrichment, high sensitivity, low cost, portable sensor system, no need for a light source, which is quite suitable for bioanalysis. This paper reviews the ECL-BPE strategy for bioanalysis and proposes the future research …

An Enzymatic Ethanol/O2 Biofuel Cell Powered By Commercial Vodka Fuel, Yi-Ming Yan, Lan-Qun Mao

Journal of Electrochemistry

This study demonstrates the performance of a new type alcohol/O₂ biofuel cell assembled by using alcohol dehydrogenase (ADH) and bilirubin oxidase (BOD) as the biocatalysts of the bioanode and the biocathode for the bioelectrocatalytic oxidation of alcohol and reduction of oxygen, respectively. To construct the bioanode and the biocathode, single-walled carbon nanotubes (SWCNTs) were used. In the bioanode, SWCNTs were used as the supporting materials for both methylene green (MG) which was used as the electrocatalyst for the oxidation of NADH and ADH. The as-constructed MG/ADH/SWCNTs-based bioanode exhibits a good activity toward the bioelectrocatalytic oxidation of ethanol. In the …

Electrochemical Detection Of L-Cysteine Based On Iron Phthalocyanine/Nitrogen-Doped Graphene Modified Electrodes, Jing-Jing Xiao, Hui-Ying Xu, Li Xu, Bao-Hong Liu

Journal of Electrochemistry

In this study, we report a facile method to develop FePc/N-G hybrid modified electrode for the detection of L-cysteine. The electrochemical sensor was characterized by cyclic voltammetry and amperometric response. The sensor exhibited a wider linear range with rapid response which has outperformed pure FePc/GCE, highlighting the important role of nitrogen doped graphene as substrate for improving the electrochemical response property.

Nanosized Fe2O3 On Three Dimensional Hierarchical Porous Graphene-Like Matrices As High-Performance Anode Material For Lithium Ion Batteries, Qin-Wei Zhang, Yun-Yong Li, Pei-Kang Shen

Journal of Electrochemistry

Ferric oxide (Fe₂O₃) as a promising anode material for lithium ion battery is due to its high theoretical capacity (1007 mAh·g^-1), earth abundance and low cost. The nanosized Fe₂O₃ on the three dimensional hierarchical porous graphene-like network (denoted as Fe₂O₃-3D HPG) has been synthesized by homogeneous precipitation and heat treatment. The 3D HPG can provide a highly conductive structure in conjunction to support well contacted Fe₂O₃ nanoparticles, and effectively enhance the mechanical strength of the matrices during volume changes, as well as improve the …

Preparation And Properties Of Titanium Based Metal Oxide Electrodes For Ammonia Nitrogen Wastewater Treatment, Xue Li, Meng Xue, Ling Huang, Jun-Tao Li, Shi-Gang Sun

Journal of Electrochemistry

In this paper, four types of titanium based metal oxides electrodes were prepared by thermal decomposition method: Ti/SnO₂+Sb₂O₃, Ti/SnO₂+Sb₂O₃/SnO₂+IrO₂, Ti/SnO₂+Sb₂O₃/SnO₂+RuO₂, Ti/SnO₂+Sb₂O₃/SnO₂+CeO₂. The XRD results show that CeO₂ in Ti/SnO₂+Sb₂O₃/SnO₂+CeO₂ displayed a good crystal structure, and there was no significant oxygen evolution reaction occurred after electrolytic oxidation. Compared with the other three electrodes, the Ce-doped …

Naio4 Oxidation Of Mussel Adhesive Protein Film And Its Corrosion Protection For Mg-1.0ca Alloy, Rui-Qing Hou, Ping-Li Jiang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The effect of oxidation of mussel adhesive protein (Mefp-1) film on the corrosive resistance for Mg-1.0Ca alloy was investigated by scanning electron microscopy (SEM), atom force microscopy (AFM), electron probe microanalysis (EPMA), Infrared reflection absorption spectroscopy (IRAS) and electrochemical methods. The results showed that the NaIO₄ induced oxidation of the pre-formed Mefp-1 film with porous morphology involved structural change of the DOPA group in the protein and resulted in a more uniform film with net-like morphology. The protein film without oxidation had an increasing resistance for the corrosion of Mg-1.0Ca alloy up to 7 days exposure. After oxidation, Epit …

Computational Fluid Dynamics Simulation Of Intracranial Aneurysms - Comparing Size And Shape, Zifeng Yang, Hongtao Yu, George P. Huang, Ryan Schwieterman, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

Objective: To study the hemodynamics of an anatomic internal carotid artery aneurysm derived from a patient-specific model and then manipulate into two phantom morphologies: one growing uniformly by size and the other changing shape unevenly. Methods: The computational model of the saccular, internal carotid artery, aneurysm was constructed from 3D rotational, digitally subtracted, catheter angiography images. Computational fluid dynamics simulations were performed under pulsatile cardiac flow conditions. Velocity vectors, streamlines, pressure, and wall shear stress (WSS) and its variance distributions were quantitatively visualized. Results: The maximum pressure and WSS from the time-averaged distribution on the inside saccular surface of the …

Highly-Selective Chemiresistive Sensing And Analysis Of Vapors Using Functionalized Nanotubes, Deon Hines

Dissertations, Theses, and Capstone Projects

Specifically, the project involves the development of a diversified array of nanostructured gas-sensors comprised of selectively, novel surface-functionalized carbon nanotubes (for analyte selectivity by virtue of functionality). Harnessing carbon nanotubes with various electron withdrawing and donating groups help in determining their affinity toward certain prognostic gaseous markers thus increasing specificity of such created sensors. We have devised synthetic routes that have led to the facile production of covalently polyfunctionalized nanotubes in high yield. Seven carbon nanotube analogues were systematically considered and then chemically synthesized, from pristine single-walled nanotubes (SWNT's), for use as the main component of sensory units that was …

Synthesis And Characterization Of A Novel Polyacetal & Design And Preparation Of Superhydrophobic Photocatalytic Surfaces, Yuanyuan Zhao

Dissertations, Theses, and Capstone Projects

Polyacetal polymers are thermoplastic resins that play an important role in industry because of numerous industrial applications including automobile; household appliance; etc. The first part of this thesis (Chapter 2) is about the synthesis of a new acetal copolymer that exhibits superior thermal stability. The second part of this thesis (Chapter 3) is about the preparation and applications of TiO₂-based polymer nanocomposite films, where the reactive oxygen species (ROS) are generated on the solid surface. Catalytic nanocomposite films are an active area of research because of their potential uses for environmental remediation and chemical synthesis. Furthermore, to …

Suborbital Spaceflight: A Student Team’S Plan To Send A Rocket To Space, Bryce Chanes, William Carpenter, Julio Benavides, Matthew Haslam, Brenda Haven

Aviation / Aeronautics / Aerospace International Research Conference

The Eagle Space Flight Team was created with the goal of becoming the first undergraduate team to design, build, and launch a rocket capable of suborbital spaceflight. In order to achieve this goal, the team will have to design a rocket capable of atmospheric flight at speeds over Mach 5 and launch it on one of the largest amateur rocket motors ever made. Over the next three years, the team will progress towards accomplishing this feat through a series of incremental test flights. Before the space flight, the team will build three sub-scale rockets designed to reach altitudes of 30,000’, …

Nasa Human Exploration Rover Challenge, Gabriella E. Fortes, Zach Henney, Mo Sabliny, Johnnie Perry, Jessica Chow, Jessica Turcios, Aaron Taylor, Brenda Haven

Aviation / Aeronautics / Aerospace International Research Conference

NASA's Human Exploration Rover Challenge, held annually in at the Marshall Space Flight Center in Huntsville, Alabama, is an engineering design challenge that asks teams of student engineers to design a human-powered vehicle capable of traversing a simulated lunar surface. The rover must be able to be transported in a 5x5x5 foot cube, echoing the design constraint faced by the engineers who built the Lunar Roving Vehicles used by the astronauts of the later Apollo missions.

A Multi-Scale Based Model For Composite Materials With Embedded Pzt Filaments For Energy Harvesting, A.E. El-Etriby, M.E. Abdel-Meguid, K.M. Shalan, Tarek Hatem, Yehia Bahei-El-Din

Centre for Advanced Materials

Ambient vibrations are major source of wasted energy, exploiting properly such vibration can be converted to valuable energy and harvested to power up devices, i.e. electronic devices. Accordingly, energy harvesting using smart structures with active piezoelectric ceramics has gained wide interest over the past few years as a method for converting such wasted energy. This paper provides numerical and experimental analysis of piezoelectric fiber based composites for energy harvesting applications proposing a multi-scale modeling approach coupled with experimental verification. The multi-scale approach suggested predicting the behavior of piezoelectric fiber-based composites use micromechanical model based on Transformation Field Analysis (TFA) to …

Me-Em 2014-15 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Human-centered Engineering
• Endowed Department Chair
• Enrollment & Degrees
• Graduates
• Department News
• Faculty & Staff
• Alumni
• Donors
• Contracts & Grants
• Patents & Publications
• Faculty & Staff Directory

Chloride Incorporation Process In Ch3Nh3Pbi3-XClX Perovskites Via Nanoscale Bandgap Maps, Jungseok Chae, Qingfeng Dong, Jinsong Huang, Andrea Centrone

Department of Mechanical and Materials Engineering: Faculty Publications

CH₃NH₃PbI_3-xCl_x perovskites enable fabrication of highly efficient solar cells. Chloride ions benefit the morphology, carrier diffusion length and stability of perovskite films; however, whether those benefits stem from the presence of Cl⁻ in the precursor solution or from their incorporation in annealed films is debated. In this work, the photothermal induced resonance (PTIR), an in situ technique with nanoscale resolution, is leveraged to measure the bandgap of CH₃NH₃PbI_3-xCl_x films obtained by a multicycle coating process that produces high efficiency (≈16 %) solar cells. Because chloride …

Role Of Interphase In The Mechanical Behavior Of Silica/Epoxy Resin Nanocomposites, Yi Hua, Linxia Gu, Sundaralingam Premaraj, Xiaodong Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

A nanoscale representative volume element has been developed to investigate the effect of interphase geometry and property on the mechanical behavior of silica/epoxy resin nanocomposites. The role of interphase–matrix bonding was also examined. Results suggested that interphase modulus and interfacial bonding conditions had significant influence on the effective stiffness of nanocomposites, while its sensitivities with respect to both the thickness and the gradient property of the interphase was minimal. The stiffer interphase demonstrated a higher load-sharing capacity, which also increased the stress distribution uniformity within the resin nanocomposites. Under the condition of imperfect interfacial bonding, the effective stiffness of nanocomposites …

Almost Sure Asymptotic Stabilization Of Differential Equations With Time-Varying Delay By Lévy Noise, Dezhi Liu, Weiqun Wang, Jose Luis Menaldi

Mathematics Faculty Research Publications

This paper aims to determine that the Lévy noise can stabilize the given differential equations with time-varying delay, which has generalized the Brownian motion case. An analysis is developed and sufficient conditions on the stabilization for stochastic differential equations with time-varying delay are presented. Our stabilization criteria is in terms of linear matrix inequalities (LMIs), whence the feedback controls can be designed more easily in practice.

Derivation And Validation Of The Friction, Gravitational, And Air Forces Encountered During Installation Of Fiber Optic Cable, Faheed Olayemi Owokoniran

All Graduate Theses, Dissertations, and Other Capstone Projects

This paper presents an introduction to fiber optic cable and the fiber optic communication system. An important phase in the supply of this new technology is to transport the fiber optic cable to the vicinity of service. Cable pulling and cable blowing - laminar flow; piston type - are the two main methods of installing fiber optic cable. Both methods of installation have limiting factors that need to be evaluated in order to perform a successful installation. The limiting factors for laminar type cable blowing are further discussed in this paper. A method was proposed to determine the forces - …