Engineering Science and Materials Commons^™

Experimental Investigation Of Mechanical Behavior Of An Oxide/Oxide Ceramic Composite In Interlaminar Shear And Under Combined Tension-Torsion Loading, Skyler R. Hilburn

Theses and Dissertations

Creep behavior in interlaminar shear of an oxide-oxide ceramic composite, Nextel 720™/aluminosilicate (N720/AS), was investigated at 1100°C in laboratory air and in steam. The interlaminar shear strength (ILSS) was determined as 7.65 MPa. The creep behavior was examined for interlaminar shear stresses in the 2-6 MPa range. Primary and secondary creep regimes were observed in all tests conducted in air and in steam. Tertiary creep was noted in the tests performed at 6 MPa. Larger creep strains and higher creep strain rates were produced in steam. Surprisingly, the presence of steam had a beneficial effect on creep lifetimes. It appears …

Waste Heat Reclamation For Commercial Use, Andrew Webber

Liberal Arts and Engineering Studies

The purpose of this project was to capture waste heat to raise the temperature of groundwater for commercial applications.

Passive Biaxial Mechanical Properties And In Vivo Axial Pre-Stretch Of The Diseased Human Femoropopliteal And Tibial Arteries, Alexey Kamenskiy, Iraklis I. Pipinos, Yuris A. Dzenis, Clay Lomneth, Syed A. Jaffar Kazmi, Nicholas Y. Phillips, Jason N. Mactaggart

Department of Mechanical and Materials Engineering: Faculty Publications

Surgical and interventional therapies for atherosclerotic lesions of the infrainguinal arteries are notorious for high rates of failure. Frequently, this leads to expensive reinterventions, return of disabling symptoms, or limb loss. Interaction between the artery and repair material likely plays an important role in reconstruction failure, but data describing the mechanical properties and functional characteristics of human femoropopliteal and tibial arteries are currently not available. Diseased superficial femoral (SFA, n=10), popliteal (PA, n=8), and tibial arteries (TA, n=3) from 10 patients with critical limb ischemia were tested to determine passive mechanical properties using planar biaxial extension. All …

Me-Em Enewsbrief, March 2014, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Electrochemical Performance Of Si-C Composites Prepared By Discharge-Plasma Assisted Milling, Yu-Long Chen, Ren-Zong Hu, Hui Liu, Wei Sun, Min Zhu

Journal of Electrochemistry

Silicon-carbon (Si-C) composites, with microstructure of multi-scaled Si particles being homogenously dispersed in micro-sized carbon matrix, had been prepared by dielectric barrier discharge plasma assisted two-step milling for the first time. The Si-C composite anode had a discharge capacity of 1259 mAh·g^-1 at the first cycle, while the capacity retained 474 and 396 mAh·g^-1 after 20 and 100 cycles, respectively. Charge-discharge curves and AC impedance response indicated that both silicon and carbon phases in the composite anode were involved during the lithiation/delithiation reactions and the electron transport resistance in the Si-C composite anode was much lower than that …

Preparation Of High Performance Porous Silicon Powders By Etching Al-Si Alloy In Acid Solution For Lithium Ion Battery, Shi-Ji Hao, Chun-Li Li, Kai Zhu, Ping Zhang, Zhi-Yu Jiang

Journal of Electrochemistry

Porous silicon powders prepared by etching Al-Si alloy using an acid solution was reported in the first time. The morphology and structure of as-obtained material were investigated using scanning electron microscopy (SEM) and X-ray diffraction (XRD) method. It was found that the spongy porous silicon powders presented well crystalline structure and consisted of nano-Si particles. The particle size of porous Si powders was about 20 μm, and the specific surface area was 102.7 m²·g^-1. The electrochemical properties of porous silicon powders were evaluated as an anode material for lithium ion batteries. The material proportion in the …

Pulse Electrodeposition Of Pd-Ni Alloy Nanoparticles For Electrocatalytic Oxidation Of Formic Acid, Fang-Zu Yang, Jun-Pei Yue, Zhong-Qun Tian, Shao-Min Zhou

Journal of Electrochemistry

The Pd-Ni alloy nanoparticles with nickel atomic contents of 12.0%, 16.4% and 22.6% were successfully electrodeposited from a Pd-Ni alloy electrolyte by square wave pulse plating. The alloy nanoparticles were in the spherical shape with a diameter of 50 ~ 80 nm. As the growth potential of the alloy was negatively shifted, the nickel content of the alloy was increased, and the size of the nanoparticles was almost the same, whereas the number, the degree of crosslinking and the real active area of the nanoparticles were increased. As the nickel content of the alloy nanoparticles increased, the peak current for …

Synthesis And Electrochemical Properties Of Lico1-XMgXMno4 And Lico1-XAlXMno4 (X= 0, 0.02, 0.05, 0.1) As Positive Materials For Lithium-Ion Batteries, Mei-Ling You, Qing-Song Tong, Xiu-Hua Li, Min Lin, Xing-Kang Huang, Yong Yang

Journal of Electrochemistry

The Al-doped and Mg-doped LiCoMnO₄ materials were synthesized through solid-state reaction. The effects of doping amounts of Mg and Al on the initial capacities, discharge plateaus, and cycle performances were investigated. The morphologies and structures of the as-prepared materials were studied by scanning electron microscopy and powder X-ray diffraction. The results indicate that the as-prepared samples were composed of uniform, well-crystallized particles. The pristine LiCoMnO₄ possessed an initial capacity of 87.0 mAh·g^-1, while LiCo_0.98Mg_0.02MnO₄ and LiCo_0.98Al_0.02MnO₄ delivered 91.3 and 93.6 mAh·g^-1, respectively. The proper …

Passivation Behavior Of Aluminum Alloy During Electrochemical Machining And Its Effects On The Machining Performance, Li-Min Jiang, Wen-Bo Deng, Jun-Long Ying

Journal of Electrochemistry

The passivation behavior of aluminum alloy during electrochemical machining was investigated and discussed. The effects of processing voltage, current density, space of electrodes and electrolyte composition on electrochemical machining performance were explored. The results indicate that the electrochemical machining aluminum alloy in the composite electrolyte system containing NaNO₃ and NaF existed passivation phenomenon. Passivation action decreaseed the current efficiency and made it varied greatly with the current density. Also the passivation shifted the interspace characteristic curve of electrode notably to a negative direction. There was not passivation phenomenon in the composite electrolyte system containing the same concentrations of NaCl …

Fabrication And Impedance Performance Of Gradient Lani0.6Fe0.4O3-δ-Gd0.2Ce0.8O2 Composite Cathodes For Intermediate Temperature Solid Oxide Fuel Cell, Yang Li, Bo Huang, Meng Yuan, Zhi-Qiu Zhang, Zong-Yao Liu, Xu-Chen Tang, Xin-Jian Zhu

Journal of Electrochemistry

A LNF-GDC composite cathode with a gradual change in the composition between ScSZ electrolyte and LNF cathode was fabricated to reduce the cathode polarization resistance (R_p). The gradual change in composition between ScSZ electrolyte and LNF cathode shows the decreases in the charge transfer resistance (R_ct) and gas phase diffusion resistance (R_d). The results revealed that the Rp value, measuring 0.452 Ω·cm² at 750 °C, was the lowest for LNF-GDC composite cathodes with three layers and gradient changes in composition between ScSZ and LNF (Cathode C),, whereas the Rp value of 70%LNF-30%GDC composite …

Preliminary Study On Morphology Controllability Of Electrochemically Prepared Polyaniline By Using Aniline Aimer, Yang Zuo, Kang Shi

Journal of Electrochemistry

Employing of aniline dimer (N-phenyl-p-phenylenediamine, NPD) as the starting monomer, polyaniline was electrochemically synthesized on the surface of glassy carbon electrode in acetonitrile-aqueous mixing solutions（20% by volume）containing 1 mol·L^-1 HClO₄. Experimental results demonstrated that the polymerization of NPD occurs at the potentials about 0.2 V lower than those of aniline monomer. Furthermore, the resulting polyaniline has higher morphology controllability than those synthesized by using aniline as the stating monomer. The uniform polyaniline nanoparticles (30 nm in diameter), ultralong nanowires (length > 5 μm, 50 nm in diameter) or large area nanosheets (4 μm in length, 2 μm in …

Electrochemical Oxidation Of Ammonium Nitrite In Absorption Solution Of Flue Gas, Yong-Hong Lu, Xiao-Bo Dong, Li-Sha Wang, Yan Liu, Chen-Jian Zhu, Hai-Bo Xu

Journal of Electrochemistry

In order to make full uses of ammonium nitrite in absorption solution from flue gas simultaneous desulfurization, denitrification and demercurization processes, here the electrochemical oxidation method was used to transform ammonium nitrite into ammonium nitrate. By using polarization curve, cyclic voltammogram and galvanostatic methods, suitable electrode materials were evaluated and chosen. The influence of electrolyte composition was discussed and the appropriate process parameters were obtained. Finally, the effect of electrochemical oxidation was confirmed by chemical analysis method. In 0.05 mol·L^-1 NaNO₂ + 0.05 mol·L^-1 (NH₄)₂SO₄ simulated absorption solution (5 L, pH = …

Study On Carbon Supported Pd Catalysts Modified By Phosphomolybdic Acid For H2O2 Electrocatalytic Reduction, Li-Mei Sun, Cheng Zhang, Ying-Rong Bao, Hong-Xia Li

Journal of Electrochemistry

The Pd/C catalyst was prepared with the chemical reduction method, and phosphomolybdic acid (PMA) was modified on the Pd/C catalyst using the dipping method. The compositions and structures of the Pd/C and Pd/C modified by phosphomolybdic acid (PMA-Pd/C) catalysts were characterized with X-ray diffraction and Fourier Transform infrared spectroscopy analyses. The electrocatalytic activity and stability of the catalysts for the reduction of hydrogen peroxide (H₂O₂) were studied using cyclic voltammetry and chronoamperometry. The results showed that the phosphomolybdic acid was tightly fixed on the surface of Pd/C catalyst through the chemical interaction. The eletrocatalytic activity of …

Preparation Of Pd/Tio2/C Catalyst And Its Electrocatalytic Performance In Basic Solution For Ethanol Oxidation, Qiao-Xia Li, Yi-Chao Yang, Ming-Shuang Liu, Hong-Min Mao, Qun-Jie Xu

Journal of Electrochemistry

Nanoparticles TiO₂ were prepared by hydrothermal method using precursor tetrabutyl titanate. The Pd/TiO₂/C catalyst was synthesized by liquid phase reducing method supported on nano TiO₂ and Vulcan carbon XC-72. The Pd/TiO₂/C catalyst was characterized by XRD, TEM, cyclic voltammetry, and chronopotentiometry. XRD confirmed the face-centered cubic structure of Pd particles, and TEM indicated that Pd particles (size 3 ~ 4 nm) dispersed uniformly on TiO₂ and carbon XC-72. The results from cyclic voltammogram and chronopotentiogram showed the higher ethanol oxidation activity and stability of Pd/TiO₂/C catalyst (20% Pd) as compared with …

Design And Development Of A Novel Glucose Biosensor Based On The Ferrocene-Functionalized Fe3O4 Nanoparticles/Carbon Nanotubes/Chitosan Nanocomposite Film Modified Electrode, Hua-Ping Peng, Dai-Jun Zha, Wei Chen, Ai-Lin Liu, Xin-Hua Lin

Journal of Electrochemistry

A novel platform for the fabrication of glucose biosensor was successfully constructed by entrapping glucose oxidase (GOD) in a ferrocene monocarboxylic acid-aminated Fe₃O₄ magnetic nanoparticles conjugate (FMC-AFNPs)/chitosan (CS)/multiwall carbon nanotubes (MWNTs) nanocomposite. The formation of FMC-AFNPs could effectively prevent the leakage of ferrocene and retain its electrochemical activity. This GOD/FMC-AFNPs/CS/MWNTs matrix provided a biocompatible microenvironment for retaining the native activity of the immobilized GOD. Moreover, the presence of MWNTs enhanced the charge-transport properties of the composite and facilitated electron transfer between the GOD and the electrode for the electrocatalysis of glucose. Under the optimal conditions the designed …

Methods, Systems, And Devices For Surgical Access And Inserton, Tom Frederick, Shane Farritor, Jack Mondry, Eric Markvicka, Dmitry Oleynikov, Jacob Greenburg

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments herein relate to systems, devices, and/or methods relating to Surgical procedures, and more specifically for accessing an insufflated cavity of a patient and/or positioning Surgical systems or devices into the cavity.

Systemand Method For Controlling Motion Of Spacecrafts, Piyush Grover, Christian Andersson

Department of Mechanical and Materials Engineering: Faculty Publications

A motion of an object is controlled from a geostationary transit orbit (GTO) of an earth to an orbit of a moon. A first trajectory of the motion of the object is determined from an intermediate orbit of an earth to a neighborhood of a stable manifold of a first Lagrange point (L1). A second trajectory of the motion of the object is determined from the GTO to the intermediate orbit. A third trajectory of the motion of the object is determined from the neighborhood to the stable manifold to an L1 orbit, and a fourth trajectory of the motion …

Liquid Slosh Analysis Using Smoothed Particle Hydrodynamics, Kristopher S. Field

Doctoral Dissertations and Master's Theses

The purpose of the research described here is to study the implementation of Smoothed Particle Hydrodynamics (SPH) algorithms as an adequate means for propellant slosh simulations in 1g and 0g environments. The dualSPHysics solver has been adapted for propellant slosh simulations. Simulated sloshing liquid frequency and damping ratio data for 1g cases has been compared to existing experiments for both spherical and prismatic container geometries. The 0g case has been studied to determine what further modifications would be required to obtain realistic simulations results. The findings in this research will be used to create a sloshing simulation to determine torques …

Organic Pi-Stacking Semiconducting Material: Design, Synthesis And The Analysis Of Structure And Properties, Bin Wang

Dissertations, Theses, and Capstone Projects

Organic semiconducting materials have been under intensive investigation in the recent decades for potential applications in various electronic or optoelectronic devices such as light emitting diodes, photovoltaic cells and field effect transistors. Compared to inorganic counterparts, organic charge transport materials are attractive for their abilities of forming thin-films, large area manufacturing, compatibility with flexible substrate, light weight and potential low fabrication cost. The charge transport property of the organic active layer is one of the key factors to the electronic or optoelectronic performance of devices. Research projects presented in this thesis focused on improving charge carrier mobility of organic charge …

2d & 3d Nanomaterial Fabrication With Biological Molecular Frameworks, Kristina Ivana Fabijanic

Dissertations, Theses, and Capstone Projects

Recently, there has been a heightened amount of work done in the field of biomineralization. By taking inspiration from natures' phenomenonal individualities as a means to develop new and interesting nanostructures of varying sizes and dimensions, there is a newly developed design, namely Biomimetic Crystallization Nanolithography (BCN). With this method, the simultaneous nano-patterning and crystallization has been achieved using urease as the nucleation point and the hydrolysis of urea to obtain patterns of oxide semiconductor material, namely zinc oxide, at room temperature and aqueous solvent. The new and interesting characteristic of BCN involves the construction of amorphous inks of ZnO …

Magnetic Janus Particles And Their Applications, Bin Ren

Dissertations, Theses, and Capstone Projects

Magnetic properties are important since they enable the manipulation of particle behavior remotely and therefore provide the means to direct a particle’s orientation and translation. Magnetic Janus particles combine magnetic properties with anisotropy and thus are potential building blocks for complex structures that can be assembled from a particle suspension and can be directed through external fields. In this thesis, a method for the fabrication of three types of magnetic Janus particles with distinct magnetic properties is introduced, the assembly behavior of magnetic Janus particles in external magnetic and electric fields is systematically studied, and two potential applications of magnetic …

Me-Em 2013-14 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Human-Centered Engineering
• Enrollment & Degrees
• Graduates
• Faculty & Staff
• Alumni
• Donors
• Contracts & Grants
• Patents & Publications

Numerical Study Of Crossflow Enhanced Microfiltration Of Oil-In-Water Emulsions, Nikolai Priezjev, Tohid Darvishzadeh, Volodymyr Tarabara

Mechanical and Materials Engineering Faculty Publications

No abstract provided.

Quality And Safety Of Minimally Invasive Surgery: Past, Present, And Future, Bernadette Mccrory, Chad A. Lagrange, M. S. Hallbeck

Department of Mechanical and Materials Engineering: Faculty Publications

Adverse events because of medical errors are a leading cause of death in the United States (US) exceeding the mortality rates of motor vehicle accidents, breast cancer, and AIDS. Improvements can and should be made to reduce the rates of preventable surgical errors because they account for nearly half of all adverse events within hospitals. Although minimally invasive surgery (MIS) has proven patient benefits such as reduced postoperative pain and hospital stay, its operative environment imposes substantial physical and cognitive strain on the surgeon increasing the risk of error. To mitigate errors and protect patients, a multidisciplinary approach is needed …

Measurement Of Hydrodynamic Force Generation By Swimming Dolphins Using Bubble Dpiv, Frank E. Fish, Paul Legac, Terrie M. Williams, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

Attempts to measure the propulsive forces produced by swimming dolphins have been limited. Previous uses of computational hydrodynamic models and gliding experiments have provided estimates of thrust production by dolphins, but these were indirect tests that relied on various assumptions. The thrust produced by two actively swimming bottlenose dolphins (Tursiops truncatus) was directly measured using digital particle image velocimetry (DPIV). For dolphins swimming in a large outdoor pool, the DPIV method used illuminated microbubbles that were generated in a narrow sheet from a finely porous hose and a compressed air source. The movement of the bubbles was tracked …

Introduction To Special Issue Of Journal Of Defense Modeling And Simulation: Novel Approaches To Defense And Military Modeling And Simulation, Scott D. Snyder, James M. Taylor Jr.

Peter Kiewit Institute: Faculty Publications

Developing solutions to complex problems in government and industry is a daunting task that often requires tremendous investment in time and resources to solve. Modeling and simulation (M&S) has incredible potential to streamline development and cut costs by conducting virtual experiments that give insight into performance under various test conditions. As many program managers in the federal acquisition process can attest, realistic testing of live equipment in an operational environment can be some of the most expensive parts of a development program. M&S can provide insight into mission success of yetto- bedesigned systems without the need to actually build and …

Simple Multi-Attribute Rating Technique For Renewable Energy Deployment Decisions (Smart Redd), James M. Taylor Jr., Betty Love

Peter Kiewit Institute: Faculty Publications

In the effort to provide electrical power service and the sustaining fuel required to run generators at forward-deployed bases in Afghanistan and Iraq over more than 10 years, the United States military spent billions of dollars and a paid a heavy toll in terms of human casualties. The green energy linear program for optimizing deployments (GELPOD) proof-of-concept model showed that a linear program could be used to optimize combat deployment of energy generation systems to minimize cost and casualties. Results indicated that reduction in both cost and casualties for renewable energy sources was highly dependent on fuel cost and deployment …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Dynamic Fracture Analysis Of Polycarbonate By The Optical Method Of Caustics, Guiyun Gao, Zheng Li, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Glassy polycarbonate (PC) is a widely used engineering material in industries, since it has high strength and toughness as well as good transparency. However, these advantages of PC can be suppressed by physical aging, especially its dynamic fracture toughness. In addition, the material properties of PC can be changed dramatically after large plastic compressive deformation, and it can show obvious orthotropic behavior. Here, the combined effect of aging and plastic compressive deformation on dynamic facture of PC was investigated by the optical method of caustics. The dynamic reflective method of caustics for orthotropic materials was developed here to study the …

3d Printing Technology Using High Viscous Materials-Synthesis Of Functional Materials And Fabrication Of 3d Metal Structure, Seongik Hong

Open Access Theses & Dissertations

In the 3D printing technology, the research for using various materials has been performing. In this research work, 3D printable high viscous materials are suggested as one of the solutions for problems in the traditional 3D printing technology.

First, Cu-Ag coreshell was synthesized as a functional material. In terms of the reaction rate, reaction rate limiting step was defined as a fundamental research, and then prepared Cu-Ag coreshell was printed and analyzed. Second, the high viscous Cu paste was prepared and then metal 3D printed structure was fabricated by using new printing method.

In the synThesis of Cu-Ag coreshell, different …