Engineering Science and Materials Commons^™

Electro-Catalytic Properties Of Β-Pbo2/Sb-Sno2/Ti Electrode On Phenol Oxidation, Peng Li, Yue-Min Zhao, Li-Zhang Wang, Yan-Le Zhang, Zhao-Qing Lu

Journal of Electrochemistry

The combination technology of brush pyrolysis and electroplating was employed in the preparation of β-PbO₂/Sb-SnO₂/Ti electrode. X-ray Diffraction (XRD) and Scanning Electron Microscope (SEM) results showed that the Sb-SnO₂ as an interlayer would restrain the formation of lead fluoride and the crystallization degree on the electrode surface could be as high as 100%. The grain size was calculated by Scherrer formula to be 25.2 nm and the agglomeration of lead dioxide was effectively eliminated. The potential span of diffusion control phase, oxygen evolution potential, Tafel slope for the β-PbO₂/Sb-SnO₂/Ti electrode during …

Boosting Electrocatalytic Activity Of Nitrogen-Doped Graphene/Carbon Nanotube Composite For Oxygen Reduction Reaction, Yu Zhang, Jin-Song Hu, Wen-Jie Jiang, Lin Guo, Zi-Dong Wei, Li-Jun Wan

Journal of Electrochemistry

Developing low-cost catalysts with high electrocatalytic activity for oxygen reduction reaction (ORR) has recently attracted much attention because the sluggish ORR currently limits the performance and commercialization of fuel cells and metal-air batteries as well. Nitrogen doped carbon materials have been considered as a promising candidate for the replacement of high-cost and scarce Pt-based catalysts although their electrocatalytic activity still needs to be much improved. In this work, an improved nitrogen-doped graphene/carbon nanotubes composite (N-rGO/CNT) was developed as an efficient ORR electrocatalyst. It was found that the ORR activity of N-rGO/CNT composite could be significantly enhanced by introducing iron in …

Electrochemical Deposition Of Copt Alloy Thin Film And Its Abnormal Infrared Effects, Qing-Song Chen, Guo-Cong Guo, Shi-Gang Sun

Journal of Electrochemistry

Nanostructured CoPt alloy thin film was deposited on glassy carbon substrate (denoted as CoPt/GC) under cyclic voltammetric conditions. SEM studies demonstrated that the CoPt/GC was composed of nonuniform nanoparticles with an average size of 139 nm. The composition of the CoPt/GC was analyzed by energy dispersive X-ray spectroscopy (EDS), which depicts a Co:Pt ratio of ca. 3:5. In situ FTIR spectroscopy employing CO adsorption as a probe reaction revealed that the CoPt/GC exhibits abnormal infrared effects (AIREs). The unique anomalous IR features of CO adsorbed (CO_ad) on CoPt/GC consist in the complete inversion of the CO_ad IR …

Recent Progress In Heteroatoms Doped Carbon Materials As A Catalyst For Oxygen Reduction Reaction, Wei Ding, Xue Zhang, Li Li, Zi-Dong Wei

Journal of Electrochemistry

Developing catalytic materials for oxygen reduction reactions (ORR) with high performance and low cost has been one of the major challenges for large-scale applications of fuel cells. In this review, we summarize the recent progress in the heteroatoms doped carbon materials as a catalyst for the catalysis of ORR, with an emphasis on the universal origin of their catalytic mechanisms. The future prospects of the metal-free catalyst were to find precisely controlled doping methods, to explore the role of heteroatoms in the catalysis, and to generate more active catalysts with suitable nanostructure.

Fabrication Of Pattern Of Graphene Oxide And Au Nanoparticles By Microcontanct Printing Technique, Wen-Hui Pang, Xiao-Jian Xiao, Meng-Wei Ye, Kai-Chao Deng, Jing Tang

Journal of Electrochemistry

Graphene oxide (GO) was prepared by modified Hummers method. Using the GO solution as "ink", Au nanoparticles (AuNPs) and GO were transferred to the surface of ITO substrate modified with (3-aminopropyl) triethoxysilane (APTES/ITO) in a sequence. The transferred AuNPs and GO could form a uniform and dense composite pattern which was characterized by FE-SEM and AFM. Moreover, using the APTES/ITO substrate surface potential as zero, the sequences of the surface potential were APTES>GO>Au.

Fabrication And Characterization Of The Ni-Scsz Composite Anodes With A Cu-Lscm-Ceo2 Catalyst Layer In The Thin Film Sofc, Yao Lv, Bo Huang, Xi-Zhi Gu, Chun-Yi Hou, Yi-Xing Hu, Xiao-Yin Wang, Xin-Jian Zhu

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) directly operating on hydrocarbon without external reforming has the potential of greatly speeding up the application of SOFCs for transportation. In this paper, a three-layer structure anode was fabricated by tape casting and screen printing method. The addition of Cu-LSCM-CeO₂ to the supported anode surface presented better performance running on H₂ and ethanol. The maximum power densities were 511 and 390 mW?cm^-2, respectively, running on H₂ and ethanol at 750 °C. No significant degradation was observed on the anode. Consequently, the Cu-LSCM-CeO₂ catalyst layer on the surface of the …

Preparation And Electrochemical Behavior Of Pbo/Gn/Ac, Yun-Fang Gao, Yan-Ping Wang, Qiu-Shi Yao, Fu-Hua Wang, Dong-Lei Ren, Xin Xu

Journal of Electrochemistry

The lead oxide/graphene/activated carbon (PbO/GN/AC) composite materials were prepared by impregnating commercial activated carbon and graphene in saturated lead nitrate solution followed by calcination. The structures and morphologies of the composite were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results show that PbO crystals (about 200 nm) were dispersed uniformly on the surface of activated carbon and graphene. Electrochemical data indicate that the composite exhibited good electrochemical performances. The PbO/GN/AC composite possessed the higher over-potential of hydrogen evolution and the high specific capacitance of 312.6 F·g^-1, while the internal resistance …

Electrochemical And Spectroscopic Studies Of Ethanol Oxidation On Nano-Cubic Pt Modified By Tin Adatoms, Lu Rao, Bin-Wei Zhang, Yan-Yan Li, Yan-Xia Jiang, Shi-Gang Sun

Journal of Electrochemistry

The nano-cubic Pt modified by tin (Sn) was synthesized and used to investigate the role of this adatom played in the ethanol oxidation. The onset potential of ethanol oxidation was significantly shifted negatively which can be forward about 300 mV when the coverage of Sn (θSn)was 0.9. The electrtochemical in situ FTIR result demonstrated that the amount of CO₂ increased first, and then decreased with θSn increased, and reached the maximun when θSn was 0.38. Furthermore, the formation of acetic acid could be observed at very low potential (-0.05 V) after modifying Sn adatom, and the amount of acetic …

Preparation Of Pt/Dna-Mwcnts/Gc Electrode And Its Electrocatalytic Activity Toward H2O2 Reduction, Li-Li Fan, Li-Na Wu, Zhi-Yu Qu, Dan-Feng Liu, Jun-Ming Zhang, Si-Ming Fan, You-Jun Fan

Journal of Electrochemistry

The DNA-multi-walled carbon nanotubes (MWCNTs)/glassy carbon (GC) electrode was prepared by modifying the DNA functionalized MWCNTs composite on a GC electrode. A novel non-enzymatic H₂O₂ sensing electrode was fabricated by electrodepositing Pt nanoparticles on the DNA-MWCNTs/GC electrode. The modified electrodes were characterized by scanning electron microscope (SEM). The response properties of the sensing electrode to H₂O₂ were investigated by cyclic voltammetry and chronoamperometry. The results indicated that the sensing electrode exhibited a good linear relationship between response current and H₂O₂ concentration in the range of 0.04 ~ 18.07 mmol·L^-1 with …

On The Origin Of The Errors Of IK As Estimated From K-L Equation In Rotating Disk Electrode System, Wei Chen, Ling-Wen Liao, Zheng-Da He, Yan-Xia Chen

Journal of Electrochemistry

Rotating disk electrode system is mainly used to study the kinetics of reactions whose reactants have very low solubility in the electrolyte. For an irreversible reaction, Koutecky-Levich equation (K-L Eq.) is frequently used to deduce the kinetic current i_k). Since K-L Eq. is derived based on the assumption that a system should conform the steady-state diffusion conditions, the data recoded from the actual system which deviates from such a condition, great error may be induced for the i_k estimated. In this work, polarization curves for oxygen reduction reaction at polycrystalline Pt electrode recorded in solutions with various …

Synthesis, Fabrication And Characterization Of Magnetic And Dielectric Nanoparticles And Nanocomposite Films, Xiaohua Liu

Dissertations, Theses, and Capstone Projects

Materials science is an interdisciplinary field investigating the structure-property relationship in solid-state materials scientifically and technologically. Nanoscience is concerned with the distinctive properties that matter exhibits when confined to physical dimensions on the order of 10^-9 meters. At these length scales, behaviors of particles or elaborate structures are often governed by the rules of quantum mechanics in addition to the physical properties associated with the bulk material.

The work reported here seeks to employ nanocystals, binary nanocomposites and thin films of materials, to build versatile, functional systems and devices. With a focus on dielectric, ferroelectric, and magnetoelectric performance, a …

Design Of Well-Defined Mesoporous Silicas Via Surfactant Templating Method Enhanced By The Use Of Swelling Agents, Tiffany Man

Dissertations, Theses, and Capstone Projects

Surfactant-templated ordered mesoporous materials continue to attract tremendous attention as these materials are characterized by reproducibility and predictability of their synthesis as well as their wide range of potential applications, which serve as future opportunities for additional advancement. The main purpose of this dissertation is to advance the understanding how to control the structural features and properties in the synthesis of well-defined porous materials via surfactant templating method, while keeping in mind that the uniformity of pore size and structural ordering are essential characteristics for these well-defined materials. The work was primarily focused on the issue of the unit-cell size …

Synthesis And Evaluation Of Sensitizer Drug Photorelease Chemistry: Micro-Optic Method Applied To Singlet Oxygen Generation And Drug Delivery, Goutam Ghosh

Dissertations, Theses, and Capstone Projects

This thesis summarizes a new micro-optic method for singlet oxygen generation and sensitizer drug delivery, which include i) synthesis and evaluation of a first generation device for drug delivery from native and fluorinated silica probe tips, ii) synthesis of PEG conjugated sensitizers to study phototoxicity in ovarian cancer cells, and iii) synthesis and evaluation of tris-PEGylated chlorin conjugated fluorinated silica for its future integration into the device to use as a 2nd generation device. A first generation micro-optic device was developed that works by sparging O2 gas and light generating cytotoxic singlet oxygen that cleaves the covalently attached drug (sensitizer) …

Characterization Of Wide Band Gap Semiconductors And Multiferroic Materials, Bo Cai

Dissertations, Theses, and Capstone Projects

Structural, optical and electrical properties of zinc oxide (ZnO), aluminum nitride (AlN), and lutetium ferrite (LuFe₂O4) have been investigated. Temperature dependent Hall Effect measurements were performed between 80 and 800 K for phosphorus (P) and arsenic (As) doped ZnO thin films grown on c-plane sapphire substrate by RF magnetron sputtering. These samples exhibited n-type conductivity throughout the temperature range with carrier concentration of 3.85 × 10 ¹⁶ cm^-3 and 3.65 × 10 ¹⁷ cm^-3 at room temperature for P-doped and As-doped ZnO films, respectively. The Arrhenius plots of free electron concentration of those doped samples showed …

Me-Em Enewsbrief, September 2014, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Electrochemical And Surface Enhanced Raman Spectroscopic Studies Of Benzimidazole On Nickel Electrode, Ping-Jie Wei, Ya-Xian Yuan, Min-Min Xu, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

By measuring cyclic voltammograms and polarization curves, the inhibition effects of benzimidazole (BMIH) concentration in acetonitrile system on a nickel electrode were investigated. It was found that the oxidation and the corrosion potentials shifted positively, and the oxidation current decreased with the increase in the concentration of BIMH. Potential dependent adsorption and film formation behavior of BMIH on the nickel electrode were investigated by in situ SERS spectroscopy. With the potential moving from negative direction to positive direction, the complexes made of BIMH and nickel were formed, preventing the nickel electrode from corrosion. In addition, the 0.001 mol·L^-1 of …

Synthesis Of Silver Nanoparticles Supported On Graphene Quantum Dots For Oxygen Reduction Reaction, Jian Ju, Wei Chen

Journal of Electrochemistry

Silver-based catalysts have been extensively investigated as the platinum substituted catalysts due to their high catalytic efficiency, low cost and long-term durability. In this study, the surfactant-free silver nanoparticles supported on graphene quantum dots were synthesized through a facile approach without addition of any other protecting ligands and reducing agents. The “surface-clean” silver nanoparticles had remarkable electrocatalytic performance towards oxygen reduction reaction (ORR) with the most efficient four-electron transfer process. Compared with commercial Pt/C catalyst, the hybrid nanoparticles showed comparable catalytic performance for ORR but much higher tolerance to methanol. Such silver nanoparticles supported on graphene quantum dots may have …

Cyclic Voltammetric Studies In Adsorption Of Cetyltrimethylammonium Bromide (Ctab) On Au(111) Electrode, Ling Chen, Chang-Deng Xu, Jin-Yu Ye, Chun-Hua Zhen, Shi-Gang Sun

Journal of Electrochemistry

Adsorption of cetyltrimethylammonium bromide (CTAB) on Au(111) electrode was investigated by cyclic voltammetry (CV). The results demonstrate that the adsorption of CTAB on Au(111) yields particular CV features. Both the adsorption of CTA⁺ and the phase change of the surfactant film are surface structure selective. Two pairs of stable sharp peaks that depend on halide species appear upon the adsorption of cationic surfactant on Au(111) electrode. The relationship between the peak current density and the scan rate indicates that the electron transfer reaction was controlled by diffusion process. These CV features are observed for the first time, and reflect …

Electrochemical Catalysis: A Dft Study, Li Li, Zi-Dong Wei

Journal of Electrochemistry

In this review, we focus on achievements in electro-catalysis based on the density function theory study. The relationships among the electrode potential, electronic structure of catalysts and electro-catalytic activity are summarized in three parts: the adsorption and desorption of species, electron transfer, and stability of catalysts. The electrode potential and the electronic structure (d-band center or Fermi (HOMO) energy) of catalysts significantly influence the formation, adsorption and desorption of surface species on electrode. The electro-catalytic activity can be improved by modulating the electrode potential and electronic structure of catalysts.

High Sensitive Detection Of Cd(Ii) And Pb(Ii) Based On Antimony-Film Covered Pencil Core Electrodes, Shan Chen, Zhao-Yan Zheng, Yi-Min Fang, Li-Qing Zheng, Jian-Jun Sun

Journal of Electrochemistry

In this paper, a pencil core was used as the substrate for an antimony-film electrode for simultaneous detection of Cd(II) and Pb(II) by square-wave anodic stripping voltammetry (SWASV). With the deposition time of 180 s, the low limit of detection (LOD) for the electrode was determined to be 0.075·g?L-1 for Cd(II), while 0.13·g·L-1 for Pb(II) with good reproducibility in low pH solutions (pH = 2). The results show a much lower LOD than that of bismuth-film pencil core electrode. Finally, this antimony-film electrode was successfully applied to determine Cd(II) and Pb(II) in tap water.

A Sensitive And Label-Free Electrochemical Aptasensor Based On Signal Amplification Of Carbon Nanotubes, Chun-Yan Deng, Hui-Min Fan, Juan Xiang, Yuan-Jian Li

Journal of Electrochemistry

A label-free electrochemical sensing electrode for highly sensitive detection of adenosine was constructed based on the signal amplification of carbon nanotubes (CNTs). The change in the interfacial feature of the modified electrode was characterized by electrochemical impedance spectroscopy. Using [Ru(NH₃)₆]³⁺ as the signaling moiety, adenosine with concentrations as low as 0.027 nmol·L^-1 can be selectively detected. Additionally, the fabrication of this present aptasensor was simple, time-saving and cost-effective. Compared with other reported aptasensors, the proposed aptasensor had advantages of excellent sensitivity, selectivity and simplicity, which plays a potential role in development of aptasensor.

Investigation Of The Dynamics Of Photocarriers During Photoelectrochemical Water Splitting By Combination Of Photoelectrochemistry And Transient Absorption Spectroscopy, Wen-Hua Leng

Journal of Electrochemistry

Semiconductor photoelectrochemical hydrogen production is an important and promising technology for utilizing solar energy. The efficiency of hydrogen production depends on the efficiencies of separation and transport of photo-generated carriers. A deep understanding of the behavior of these processes has guiding significance for designing efficient solar hydrogen device. photoelectrochemical and transient absorption spectroscopy methods are powerful tool for studying the microscopic dynamics and mechanism of photocatalytic reaction. This review describes the part of the latest results of the author regarding the semiconductor photoelectrochemical hydrogen production obtained by these methods,and the problems and future research priorities in this field are proposed.

Recent Progress In The Mechanistic Understanding Of Formic Acid Oxidation On Pt Electrode, Jie Xu, Dao-Chuan Jiang, Dong Mei, Zheng-Da He, Yan-Xia Chen

Journal of Electrochemistry

This article reviews the recent progress in understanding of the mechanisms for formic acid oxidation on Pt electrode. There are two pathways for formic acid oxidation on Pt electrode: (1) Indirect Pathway through which HCOOH is oxidized to CO₂ through CO_ad intermediate. This pathway contributes only 1% of the total current; (2) Direct Pathway where HCOOH is oxidized directly to CO₂. The results from IR Spectroscopy, single-crystal electrochemistry and DFT calculation all support that the bridge-bonded formate is neither the intermediate of direct pathway nor the precursor for CO_ad formation in indirect pathway. Possible mechanism …

Electrocatalytic Oxidation Of Formate On Pd-Cu/C - Effect Of Dealloying Pretreatment, Kun Jiang, Ye Wang, Tao Lin, Wen-Bin Cai

Journal of Electrochemistry

Carbon supported highly dispersed Pd-Cu nanoalloy catalyst toward formate electrooxidation is prepared via one-pot synthesis by using ethylene glycol as the reducing agent and sodium citrate as the stabilizer. The as-prepared catalyst is structurally characterized by TEM and XRD. The Cu dealloyment is carried out through repetitive potential cycling of the Pd-Cu/C catalyst in an acidic solution. The dealloying effect on the performance of the Pd-Cu/C is investigated by using cyclic voltammetry and chronoamperometry, and the surface structural change of Pd-Cu/C is probed by in situ ATR-IR measurement. The results show that the as-prepared Pd-Cu/C processes a better long-term stability …

Preparation And Lithium Storage Performance Of Sn-Snsb Nanoparticles, Yao Xiao, Jiao-Hong Wu, Qi Wang, Ling Huang, Jun-Tao Li, Shi-Gang Sun

Journal of Electrochemistry

Tin was widely studied as alternative anode material to carbon for lithium-ion batteries thanks to its much higher theoretical capacity. However, a pure tin electrode suffers severely from its poor cycleability due to mechanical fatigue caused by volume change during lithium insertion and extraction processes. Tin-based alloy may improve the cycleability property of tin electrode. In this article, we report facile synthesis of spherical Sn-SnSb nanopartciles using a simple solvent-thermal approach. It is amazing to find that the spherical Sn-SnSb nanoparticles can circumvent volume changes effectively during charge-discharge process. Electrochemical discharge/charge results show that the spherical Sn-SnSb nanoparticles electrode exhibits …

Electrochemical Fabrication Of Two-Dimensional Flower-Like Pt Nanostructures For Methanol Electrocatalytic Oxidation, Xia Wang, Jun Hu, Yong-Jun Li

Journal of Electrochemistry

Two-dimensional flower-like Pt nanostructures (2D FPNs) were fabricated on glassy carbon substrates by galvanostatical electrochemical technique. The electrolyte was the HAuCl₄ + HClO₄ aqueous solution without addition of any structure-directing organic reagent, which made as-prepared Pt nanostructures cleaner, exhibiting much higher reactivity. Scanning electron microscopic images revealed that 2D FPNs were spherical Pt nano-flowers constructed by the smallest building blocks, nano-leaves. The number density of spherical Pt nano-flowers can be tuned by controlling the electrodeposition time. High resolution transmission electron microscopic images indicated that each nano-leaf was formed by growing along Pt(111) direction. Electrocatalytic activities of as-prepared 2D …

Preparation Of Pt-Tio2/Graphene Composites With High Catalytic Activity Towards Methanol Oxidation And Oxygen Reduction Reaction, Li Qi, Ying Yin, Wen-Guang Tu, Bing-Bing Wu, Zhao-Sheng Wang, Jian-Guo Liu, Jun Gu, Zhi-Gang Zou

Journal of Electrochemistry

A series of graphene-supported TiO₂ nanoparticles (TiO₂/G) with different TiO₂ contents were prepared by a facile hydrothermal method, and then the Pt-TiO₂/G catalysts were successfully prepared by reducing Pt-precursor with microwave technique. Compared with Pt-G catalysts, the catalytic performance toward oxygen reduction reaction (ORR) and methanol oxidation reaction (MOR) of Pt-TiO₂/G catalysts was improved due to the addition of TiO₂. However, the excessive TiO₂ would lead to a poor catalytic performance of Pt-TiO₂/G catalysts because of the low electrical conductivity of TiO₂.

Effecting Of Dissolved Oxygen On Microbial Fuel Cells Based On Pseudomonas Aeruginosa, Chang-Li Cao, Li-Xiang Chen, Ran-Ran Wu, Ken-Lin Chang, Feng Zhao

Journal of Electrochemistry

In this work, the reaction between the electron shuttle secreted by Pseudomonas aeruginosa and anode was studied by measuring cyclic voltammogram and open circuit potential. The effect of dissolved oxygen on the oxidation reaction of anode was explored. It was demonstrated that the reaction was a diffusion-controlled and reversible process. The anode was a little affected when the dissolved oxygen of inocula was low (0 ~ 1.6 mg·L^-1). The polarization curves showed that the current output of microbial fuel cells decreased 7% with the impact of dissolved oxygen.

Analytical And Experimental Analysis Of Magnetorheological Elastomers, Sarah Trabia

UNLV Theses, Dissertations, Professional Papers, and Capstones

Many engineering applications ranging from robotic joints to shock and vibration mitigation can benefit by incorporating components with variable stiffness. In addition, variable stiffness structures can provide haptic feedback (the sense of touch) to the user. In this work, it is proposed to study Magnetorheological Elastomers (MRE), where iron particles within the elastomer compound develop a dipole interaction energy, to be used in a device for haptic feedback. A novel feature of this MRE device is to introduce a field-induced variable shear modulus bias via a permanent magnet and using a current input to the electromagnetic control coil to change …

Integrating 3d Layered Manufacturing With Photonic Sintering, Precision Machining And Smart Coating Techniques For Rapid Casting Applications, Hemant Bohra

Dissertations

Developments in rapid casting technologies have led to a new era of inclusion of 3D printing. Three-Dimensional (3D) printing provides the flexibility and ease of reproducing a sand mold directly from CAD models, eliminating patterning steps, thus reducing the process time for creating prototypes. In addition to minimizing processing steps, 3D printing provides the advantages of higher precision and the ability to produce complex shaped sand molds, but it simultaneously possesses some limitations and concerns related to throughput, safety and logistics.

This study proposes an alternative method for creating sand molds by introducing a hybrid rapid prototyping approach to overcome …