Engineering Science and Materials Commons^™

The Effects Of Microstructure On Fretting Fatigue Behavior Of Nickel Alloy In-100, Erik C. Saladin

Theses and Dissertations

This thesis studied the effect of microstructure on the fretting fatigue behavior of IN-100. First, fretting and plain fatigue S-N curves were determined over a large range of applied stress at an identical R-ratio and for fretting tests, done with a constant contact load. It was found that fretting fatigue reduces the cycles to failure compared to plain fatigue. The half contact width was found for the specimens, the crack initiation angle was found to be 40 deg and the crack initiation location was at the trailing edge of contact for the fretting specimens. Computational work included finding the stress …

Effects Of Prior Aging At Elevated Temperature In Air And In Argon Environments On Creep Response Of Pmr-15 Neat Resin, Joseph L. Broeckert

Theses and Dissertations

Creep behavior of PMR-15 neat resin, a polyimide thermoset polymer, aged in air or argon gaseous environments at 288 °C for up to 1000 h was evaluated. Creep tests were performed at 288 C at creep stress levels of 20 and 10 MPa. Creep periods of at least 25 h in duration were followed by recovery at zero stress. Weight loss and growth of the oxidation layer were also monitored and correlated with aging time. The aging time in both air and argon environments had a strong influence on the creep and recovery response of PMR-15 neat resin. Samples aged …

Preparation And Lithium Storage Performance Of Nano-Structural Sno2/Carbon Nanotubes Composite Electrodes, Hong-Bing Wei, Ling Huang, Xiao-Bin Wu, Fu-Sheng Ke, Jin-Shu Cai, Xiao-Yong Fan, Fang-Zu Yang, Shi-Gang Sun

Journal of Electrochemistry

The Nano-structural SnO₂/Carbon Nanotubes Composites were prepared in a solution of SnCl₂,ethylene glycol(EG),purified MWCNTs and sodium dodecyl sulfate(SDS) at 160 ℃.The phase structure and surface morphology of the composites were measured by XRD HRTEM and SEM.The results indicate that there are high dispersions and high loadings of SnO₂ nanoparticles on MWCNTs.Electrochemical lithium storage performance was studied preliminarily on the obtained samples.MWCNTs modified with SnO₂ nanoparicles were shown to have a higher electrochemical reversible capacity than that of MWCNTs during the charge and discharge process.MWCNTs can accommodate the larger structure strain of the active materials …

Effects Of Direct Current Bias Potentials On Lipid Membranes Forming On A Glassy Carbon Electrode, Yu-Hui Li, Hong-Wei Zhang, Gui-Lan Song, Zhan-Jun Zhang, Sheng-Min Cai

Journal of Electrochemistry

The effects of direct current(DC) bias voltage on the structure of lipid membranes forming on a glassy carbon electrode(GCE) was investigated by cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS).The experiment showed that the lipid membranes can be formed with either positive or negative bias potential exerted.When bias voltage was exerted,bilayer lipid membranes tended to form due to the electrostatic interaction between the superficial positive charges on the polarized electrode and the negative charged part of PC.When the positive bias voltage overrun the range,the lacunas on s-BLMs would increase,and the BLMs would be broken.A proper equivalent circuit was nonlinearly fitted,based on the …

Composite Electroplating And Characterizations Of Sn-Sba15 Anode For Lithium-Ion Batteries, Xiao-Yong Fan, Jin-Mei Xu, Quan-Chao Zhuang, Hong-Hong Jiang, Ling Huang, Yan-Xia Jiang, Quan-Feng Dong, Shi-Gang Sun

Journal of Electrochemistry

Sn-SBA15 anode was prepared by composite electroplating. The first discharge and charge capacity was 1075mAh/g and 630mAh/g respectively. After fifty charge/discharge cycles, the charge and discharge capacity of Sn-SBA15 were retained above 400mAh/g. XRD patterns indicated that the Sn-SBA15 has tetragonal crystal type. SEM images showed that the Sn-SBA15 had a honeycombed surface. EIS results indicated that there was SEI film formed on the surface of Sn-SBA15 electrode.

Comparison Of The Electrochemical Reactivity Of Electrodes Modified By Carbon Nanotubes With Different Sizes, Guo-Feng Yang, Neng-Qin Jia, Zhi-Yong Wang

Journal of Electrochemistry

The electrochemical activity of multi-walled carbon nanotubes(MWNTs) with different sizes,including four different MWNTs with the same length and different diameter,two different MWNTs with the same diameter and different length has been assessed and compared.The various MWNTs modified electrodes were prepared by immobilizing the suitable amount of MWNTs onto a glassy carbon electrode,and their voltammetric responses to ferricyanide,uric acid and dopamine were examined.The corresponding cyclic voltammetric data was showed that the electrochemical and electrocatalytic activities are depended on the nanotube length.The electrochemical reactivity of short MWNT(S-MWNT) is better than that of long MWNT(L-MWNT),which may be mainly attributed to the existence of …

Mwnts Modified Gc Electrode For Hydrogen Peroxide Determination, Hong-Juan Wang, Chun-Mei Zhou, Hao Yu, Feng Peng, Jin-Kun Fang

Journal of Electrochemistry

A MWNTs modified GC electrode was constructed successfully to be used to detect hydrogen peroxide.Two methods of maximum anodic current of cyclic voltommogram and chronoamperometry were adopted to measure the concentration of hydrogen peroxide.The results show that the MWCNTs can enlarge the effective surface area of GC electrode and can enormously enhance the electron transfer.The sensitivity and correlation coefficient for hydrogen peroxide detection are 2.84 μA/mmol·L^-1,0.997 and 1.5 μA/mmol·L^-1,0.971 for cyclic voltammetry and chronoamperometry,respectively.The procedure of the two methods to detect hydrogen peroxide is simple,and the results obtained are satisfied.

Influence Of Electrolyte On The Preparation And Electrocatalytic Properties Of Pt/Gc Electrodes, Sheng-Pei Chen, Yan-Xin Chen, Tao Huang, Xiao-Wen Hou, Shi-Gang Sun

Journal of Electrochemistry

Influence of electrolyte on the electrocatalytic properties of Pt/GC electrodes for formic acid oxidation were studied by using cyclic voltammetry, SEM and electrochemical in situ FTIR spectroscopy. It has demonstrated that the surfaces of Pt/GC electrodes prepared in H₂SO₄ (Pt/GC1) or in HClO₄(Pt/GC2) are all composed of platinum particles, but which crystals are some differences in size and shape.Diameters of platinum particles on the surface Pt/GC1 are of 100~200 nm, and with spheral shape in the majority. The sizes of platinum particles on the Pt/GC2 electrode are larger in general,part of particles is of cube …

Study On The Electrochemical Machining Of Titanium Alloys Tc4 With The Method Of Uniform Design, Mei-Li Zhang, Di Zhu, Zheng-Yang Xu

Journal of Electrochemistry

For the electrochemical machining of titanium alloys,a passivating film tends to form on the machining surface,which holdbacks the process of machining;and some corrosive pittings can appear on the non-machining surface,which leading to the poor surface quality.So how to improve the machining surface quality,this is a hot problem in aerospace industries.An experiment plan has been made with the method of uniform design and the variance analysis has been carried out using the result data of the previous experiments.The experimental results show that an excellent machining surface with Ra 0.38 μm would be obtained in the electrolyte of 10% NaCl solution,4% Na …

Electrochemical Characteristics Of La0.7-XCeXMg0.3Ni2.4Co0.6(X=0～0.4) Hydrogen Storage Alloys, Ling-Ling Xiao, Yi-Jing Wang, Yi Liu, Jian-Sheng Cao, Da-Wei Song, Li-Fang Jiao, Hua-Tang Yuan

Journal of Electrochemistry

The effect of partial substitution of Ce for La on the structure and the electrochemical properties of the La_0.7-xCe_xMg_0.3Ni_2.4Co_0.6(x=0～0.4)hydrogen storage alloys have been investigated systematically.The result of X-ray powder diffraction(XRD) show that the alloys are all consisted of the LaNi₃ phase and the LaNi₅ phase.The maximum discharge capacity is decreased gradually with increase of the Ce contents,but the cycling life is improved obviously.

Fabrication And Performance Of Ni-Scsz Cermet Anode Modified By Coating With Gd0.2Ce0.8O2 For A Sofc, Ren-Zhu Liu, Bo Huang, Xiao-Feng Ye, Shao-Rong Wang, Jia-Di Cao, Huai-Wen Nie, Ting-Lian Wen

Journal of Electrochemistry

A Ni-scandia-stabilized zirconia(Ni-ScSZ) cermet anode modified by coating with nano-sized gadolinium-doped ceria(GDC,Gd_0.2Ce_0.8O₂) was prepared using a simple combustion process for the solid oxide fuel cell(SOFC) running on methane fuel. X-ray diffraction(XRD) and scanning electron microscopy(SEM) indicated that the surface of Ni-ScSZ was coated by nano-sized GDC particles(<100nm). Single cell testing showed that the 2.0%(by mass) GDC-coated Ni-ScSZ anode had better performance. The highest power densities of the cell with this anode were 825 and 848mW/cm² at 850℃ in humidified hydrogen and methane, respectively, whereas the corresponding values were 584 and 586mW/cm² for the cell with Ni-ScSZ anode.Electrochemical impedance spectra(EIS) illustrated that the cell with Ni-ScSZ anode exhibited far greater impedances than the cell with 2.0%(by mass) GDC-coated Ni-ScSZ anode.Then the …

The Influence Of Electrolytic Conditions On Synthesis Of Feo42-, Yan Zhou, Wei-Hua Yang, Dong-Qin Bi, Ting-Ting Huang, Zhen Sun, Quan-Feng Guo

Journal of Electrochemistry

The FeO₄^2-was synthesized using iron lattice as anode and the solid K₂FeO₄ was also prepared.Influence of electrolytic conditions,such as stir,ultrasonic,temperature and current density on the current efficiency were studied.The results showed that preferable ferrate(VI) current yield was obtained in a current density of 10 mA·cm^-2,temperature 30 ℃ and 14 mol/L NaOH as electrolyte under at stirring effect.

Variable Frequence Switching Power Supply Used To Aluminum Foil Corrosion, Xiang-Dong Zhuo, Lan Sun, Guo-Qing Qian, Chang-Jian Lin

Journal of Electrochemistry

A new variable frequence and multi-wave power supply used to aluminum foil corrosion is introduced. The switching supply power supply controlled by the microcontroller and Variable Frequence in low band and multi-wave, big power supply controlled by the electronic switch bridge for changing phase were designed. This power supply does not need bulky and cumbersome transformer, and the frequency at lower limit is not limited, even lower than 1Hz.

Electrochemical Oxidation Of The Phenol In The Chloride System, Yong Liu, Dan Liu, Shi-Lin Zhao, Jing-Jing Lai

Journal of Electrochemistry

The Ru-Ir /Ti electrode as cathode to electrolysis the synthetic phenolic wastewater was studied. The effect of the initial chloride concentration on the electrolytic treatment result has been discussed. Experiment result shows that the electrochemical oxidation of phenol suits to one kinetics equation in given electrolytic time. If the initial chloride concentration in wastewater increases, the time of the electrochemical oxidation of phenol can be shorten, in other words the apparent rate constant is greater. The middle matters of electrochemical oxidation of phenol in the chloride system detected out by HPLC and GC-MS is mainly 1-chloro-phenol, 4-chloro-phenol, 2,4-dichloro-phenol, 2,6-dichloro-phenol, 2,4,6-trichloro-phenol, …

Diamond-Like-Carbon Film Prepared On Stainless Steel Substrates By Liquid Phase Electrochemical Deposition, Jing-Yong Du, Gui-Feng Zhang, Guo-Qing Li, Xiao-Duo Hou

Journal of Electrochemistry

Diamond-like carbon (DLC) films were deposited on stainless steel substrates at atmospheric pressure and low temperature (60 ℃) by electrolysis in a methanol solution with a pulseddirect current power supply. The morphology and microstructure of the resulting DLC films were analyzed using atomic force microscopy(AFM), scanning electron microscopy (SEM), Raman spectroscopy and Fourier transformation infrared spectrometry (FTIR). The experimental results show that the hydrogenated diamond-like carbon filmsare smooth and compact. Raman spectroscopy analysis confirmed the presence of a strongpeak at 1332.51 cm^-1, which is assigned to crystalline diamond. The deposition rate can be enhanced to 0.5 μm/h by …

Effect Of Heat Treatment On Microstructure, Hardness & Superelasticity Of Severely Deformed Niti, Omar Bahy El-Din Mortagy

Archived Theses and Dissertations

No abstract provided.

Dynamic Networking Of Exemplars: Towards A Mechanical Design Visual Programming Language, Shashidhar Putti

All Theses

Developing mechanical engineering design automation applications using current day textual programming languages like C, C++ requires extensive programming skills. However, learning to program in these environments can be time consuming and often frustrating to mechanical engineers due to the use of complex textual constructs and syntax to represent an algorithm in a linear fashion. Further, these programming languages offer a poor visualization of the data and the data flow due to their textual nature. The use of graphical objects for programming makes visualization easier and also eliminates the need for linear representation of algorithms. This thesis initiates the development of …

Me-Em 2007 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Research Expansion
• Research Groups
• Faculty & Staff
• Students
• Alumni
• Resources
• Graduates
• Publications

Microstructures And Viscoelastic Properties Of Anisotropic Magnetorheological Elastomers, Lin Chen

Articles

The microstructures and viscoelastic properties of anisotropic magnetorheological elastomers were investigated in this paper. The measurement results show that their mechanical properties are greatly dependent on the magnetic flux density applied in preparation. A finite-column model was proposed to describe the relations between the microstructures and the viscoelastic properties. The simulation results agree well with the experimental results.

Investigation On Magnetorheological Elastomers Based On Natural Rubber, Lin Chen

Articles

Magnetorheological Elastomers (MR Elastomers or MREs) are a kind of novel smart material, whose mechanical, electrical, magnetic properties are controllable under applied magnetic fields. They have attracted increasing attentions and broad application prospects. But conventional MREs are limited to wide applications because their MR effects and mechanical performances are not high enough. This paper aims to optimize the fabrication method and to fabricate good natural rubber based MREs with high modulus by investigating the influences of a variety of fabrication conditions on the MREs performances, such as matrix type, external magnetic flux density, and temperature, plasticizer and iron particles. Among …

Improved Hole-Injection Contact For Top-Emitting Polymeric Diodes, Juo-Hao Li, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this letter, an efficient hole-injection contact was achieved for the top-emitting polymeric light-emitting diodes (PLEDs). The anode has a structure of metal/molybdenum oxide/ poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS). It has been found that hole injection was significantly improved by inserting a thin layer of MoO₃ between aluminum and PEDOT:PSS. An ultraviolet photoelectron spectroscopy (UPS) was used to investigate the change of work function, and photovoltaic measurement confirmed that the improved hole injection is due to the reduction of barrier height, resulted from the addition of transition metal oxide. PEDOT:PSS layer was found necessary in anode structure to further enhance the …

A Novel Processing Route For The Production Of Nanoparticulate Zinc Oxide, Declan Mccormack, Grainne Duffy, Suresh Pillai

Articles

Zinc oxide nanoparticles have been processed from a novel isophthalate
precursor. In contrast to those processed from an oxalate precursor, this
material exhibits three-dimensional, non-directional aggregation behaviour.
Such non-directional aggregation of uniaxial crystallites may allow for the
production of structures with a higher proportion of catalytically active
surfaces than can be prepared through conventional sol–gel methods. XRD,
FTIR, TEM and SEM were used to characterize the synthesized materials.
Zinc oxide particles synthesized by using isophthalic acid
(C6H4-1,3-(COOH)2) are found to be slightly smaller than the previously
reported materials prepared through chelation with oxalic acid
(H2C2O2·2H2O).

Influence Of Van Der Waals Forces On Increasing The Strength And Toughness In Dynamic Fracture Of Nanofibre Networks: A Peridynamic Approach, Florin Bobaru Ph.D.

Department of Engineering Mechanics: Faculty Publications

The peridynamic method is used here to analyse the effect of van der Waals forces on the mechanical behaviour and strength and toughness properties of three-dimensional nanofibre networks under imposed stretch deformation. The peridynamic formulation allows for a natural inclusion of long-range forces (such as van der Waals forces) by considering all interactions as ‘long-range’. We use van der Waals interactions only between different fibres and do not need to model individual atoms. Fracture is introduced at the microstructural (peridynamic bond) level for the microelastic type bonds, while van der Waals bonds can reform at any time. We conduct statistical …

Effect Of Hole Configurations On Film Cooling From Cylindrical Inclined Holes For The Application To Gas Turbine Blades, Yiping Lu

LSU Doctoral Dissertations

Film cooling is one of the cooling systems investigated for the application to gas turbine blades. Gas turbines use film cooling in addition to turbulated internal cooling to protect the blades outer surface from hot gases. The present study concentrates on the experimental and numerical investigation of film cooling performance for a row of cylindrical holes in a modern turbine blade. The adiabatic film effectiveness and the heat transfer coefficient are determined experimentally on a flat plate downstream of a row of inclined different geometries hole exit by using a single test transient IR thermography technique. The focus of this …

Semantic Image Retrieval Using Relevance Feedback And Transaction Logs, Amin Shah-Hosseini

LSU Doctoral Dissertations

Due to the recent improvements in digital photography and storage capacity, storing large amounts of images has been made possible, and efficient means to retrieve images matching a user’s query are needed. Content-based Image Retrieval (CBIR) systems automatically extract image contents based on image features, i.e. color, texture, and shape. Relevance feedback methods are applied to CBIR to integrate users’ perceptions and reduce the gap between high-level image semantics and low-level image features. The precision of a CBIR system in retrieving semantically rich (complex) images is improved in this dissertation work by making advancements in three areas of a CBIR …

Time-Economic Lifetime Assessment For High Performance Thermal Barrier Coating Systems, Marion Bartsch, Bernd Baufeld, S. Dalkilic, Iulian Mircea, K. Lambrinou, T. Leist, J. Yan, Anette M. Karlsson

Mechanical Engineering Faculty Publications

Strategies for time-economic lifetime assessment of thermal barrier coatings (TBC) in service are described and discussed on the basis of experimental results, achieved on material systems with coatings applied by electron beam physical vapour deposition. Service cycles for gas turbine blades have been simulated on specimens in thermo-mechanical fatigue tests, accelerating the fatigue processes by an increase of load frequency. Time dependent changes in the material system were imposed by a separate ageing, where the samples were pre-oxidized prior to the fatigue test. Results of thermo-mechanical fatigue tests on pre-aged and as-coated specimens gave evidence of interaction between fatigue and …

Optimal Control Of Production And Distribution In A Supply Chain System Operating Under A Jit Delivery Policy, Pablo Biswas

LSU Doctoral Dissertations

This research deals with a supply chain system where the production or manufacturing facility operates under a just-in-time (JIT) environment, and the facility consists of raw material suppliers, manufacturers, and retailers where inventory of raw materials, work-in-process, and finished goods are involved, respectively. This work considers that the production of finished goods in one cycle starts just after the production or uptime in preceding cycle to minimize the idle time of the facility. Considering this scenario, inventory models are developed for different delivery situations: (a) perfect matching condition where no finished good remains after the shipments and (b) imperfect matching …

Optimization For Software Release And Crash, Tanvir Khan

LSU Master's Theses

Software testing is a process to detect faults in the completeness and quality of developed computer software. Testing is a key process in assuring quality by identifying defects in software, and possibly fixing them, before it is delivered to end-users. A major decision to make during this software testing is, to determine whether to continue testing and eventually releasing the software, or when to stop the test and ‘crash’ it. Such a decision needs to be made to optimally balance the tradeoff between the cost of development and the reliability of the software. In this paper, a new optimal strategy …

Development Of A Biomass Transducer For Automated Microalgal Bioreactors, Amar Shivaram Hegde

LSU Master's Theses

A highly sensitive miniaturized biomass transducer is necessary for continuous and reliable monitoring of the microalgal biomass in a computer controlled, automated microalgal bioreactor. Previous known methods to determine microalgal biomass applicable in these bioreactors are based on single wavelength turbidimetric or fluorescence. The objectives of this research were to (1) determine the light absorption characteristics of some commercially applicable microalgae in the electromagnetic wavelength range of 200-800 nm (2) design and construct a new miniaturized biomass transducer (3) process the transducer output to correlate with the biomass. Wavelength sensitivity analysis was conducted on the commercially important microalgal species - …

Processing Nano Graphene Plates (Ngps) And Ngp Nanocomposite, Yena Li

Browse all Theses and Dissertations

In recent years numerous efforts worldwide are addressing all aspects of the rapid developing field of nanocomposites. However, the most important fillers-- carbon nanotube and carbon nanofiber - are expensive. In this study, our efforts are aimed at bridging the gap in cost and properties by providing a systematic study of alternative nano materials -- nano graphene plate (NGP) and related composites. We fabricated nano graphene plates through the detailed study of raw materials, chemical treatment methods and nano particle dispersion methods. A series of thermal expansion experiments were conducted to investigate the best condition to expand acid treated graphite …