Engineering Science and Materials Commons^™

Preparation And Characterization Of Lini0.85Co0.10(Timg)0.025O2 As Cathode Materials For Lithium-Ion Batteries, Xian-Jun Zhu, Hong-Hao Chen, Hui Zhan, Dai-Ling Yang, Yun-Hong Zhou

Journal of Electrochemistry

Cathode material of LiNi_0.85Co_0.10(TiMg)_0.025O₂ were prepared by solid state reaction at 725℃ for 24 h from LiOH·H₂O, Ni₂O₃, Co₂O₃, TiO₂ and Mg(OH)₂ under flowing oxygen, and were characterized by TG-DTA, XRD, SEM and electrochemical tests. Effort to simultaneously doped LiNiO₂ with Co-Ti-Mg has been tried to improve the cathode performance. The results show that co-doping definitely has a large beneficial effect in increasing the capacity (182.7mAh/g of the first discharge capacity for  LiNi_0.85Co_0.10(TiMg)_0.025O_{2 …}

Corrosion Resistance For Tio2 Thin Films Coated 316l Stainless Steel In The Nacl Solution, Guang-Xia Shen, Yi-Cong Chen, Chang-Jian Lin

Journal of Electrochemistry

The nano-TiO₂ thin films have been deposited on the 316L stainless steel by sol-gel and the dip-coating methods. Hydrothermal post-treatment leads to crack-free coatings. Meanwhile, the surface structure and properties are optimized. Surface morphology, structure and properties are characterized by XRD, and SEM technologies. The results have shown that the surface of coatings is porous, uniform and orderly, the particle diameters are in the range of 15~18 nm and the pores are about 4~8 nm and TiO₂ is anatase. The results of electrochemical measurements show that in the NaCl solution with pH ≥ 2 and concentration below 1mol/L, …

Corrosion Behavior Of Mg2-XLaXNi And Mg2-XCeXNi Hydrogen Storage Alloy, Hai-Chang Zhang, Hua-Bin Yang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

The corrosion behavior of Mg-base hydrogen storage alloys has been investigated by potentiodynamic polarization and EIS. The results showed that the corrosion current density (i_corr) and the electrochemical polarized resistance of Mg_2-xCe_xNi alloys decreased with x increase, while i_corr of Mg_2-xLa_xNi alloys increased and the electrochemical polarized resistance of Mg_2-xLa_xNi alloys increased first, then decreased with x increase. SEM results showed that the surface of Mg_1.85Ce_0.15Ni alloy was relatively even while the surface of Mg_2-xLa_xNi alloy had …

A Study Of Metal Borides As High Capacity Anode Materials For Aqueous Primary Batteries, Ya-Dong Wang, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

The transition metal borides VB₂ and TiB₂ were tested as high capacity anode materials and their electrochemical behaviors were studied by cyclic voltammetry and discharge measurements. The experimental results indicated that transition metal borides VB₂ and TiB₂ electrodes can deliver exceptionally high discharge capacity of over 3100 mAh/g and 1 600 mAh/g respectively, corresponding to 11- and 6-electron oxidation reaction, although their parent elements V, Ti and boron, are almost completely electrochemically inert. The different electrochemical activitis were probably due to the electrochemical activation of boron, which clamp the potential to passivation for Ti and activity …

Electrochemical Performance Of Gel Polymer Electrolyte Prepared By Thermal Initiating Polymerization Of Acrylates, Jin-Dan Piao, Li-Xia Yuan, Xin-Ping Ai, Han-Xi Yang, Yu-Liang Cao

Journal of Electrochemistry

A gel polymer electrolyte was prepared by thermal initiating polymerization of the acrylates in the EC/EMC/DMC electrolyte solution at 100℃. The LiCoO₂/MCMB polymer cells were assembled and their electrochemical properties were evaluated at various charge-discharge rate and temperatures. The ionic conductivity of the polymer electrolyte containing 85wt.% liquid electrolyte is around 3.2×10^-3 S·cm^-1  at 20℃ and 5.6×10^-4 S·cm^-1 at -30℃ respectively. The gel polymer electrolyte has good electrochemical stability up to 4.5V versus Li/Li⁺.The first charge-discharge efficiency of the polymer cell at 0.2C rate is almost 92.1%. The discharge capacity of the …

Application Of Carbon Paste Electrode On The Electrogenerative-Leaching Process Of Sulfide Minerals, Shao-Fen Wang, Zheng Fang, Yun-Yan Wang

Journal of Electrochemistry

The cyclic voltammetry curves of sulfide mineral electrodes or corresponding carbon paste electrodes in NaCl electrolytes have been obtained in this study. The experimental results indicate that acetylene black (revealed) the electro-catalytic propertyin the electrogenerative-leaching process of sulfide minerals. The output currentand potential of carbon paste electrodes were increased to some degrees while the activation energies were lower.

Preparation Of Poly (Bromophenol Blue) Modified Glassy Carbon Electrode And Its Electrocatalytic Activity, Wei Chen, Hong-Bin Luo, Xin-Hua Lin

Journal of Electrochemistry

A film of poly (bromophenol blue) was formed on a glassy carbon electrode by using cyclic voltammetry. A stable film could be obtained with a potential range from -1.0 V to +1.8 V (vs.Ag/AgCl). The experimental results showed that the poly (bromophenol blue) modified glassy carbon electrode could catalyse the oxidation of ascorbic acid. It decreased the oxidation potential by about 270mV but increased the peak current. Meanwhile, this electrode showed a good linear current response for the ascorbic acid range from 2.5 to 250 (g/mL).

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu

Journal of Electrochemistry

Electrochemical oxidation is an effective technology for the phenol wastewater treatment, and the anode properties are important to the electrochemical oxidationefficiency. The over-potentials of oxygen evolution have been measured for thestainless steel, feasible graphite and SnO₂/Ti anode respectively. Moreover, the synthetic phenol wastewater was treated by the electrochemical oxidation with the stainless steel or feasible graphite anodes. The experimental results showed that the order of the over-potential is SnO₂/Ti > graphite > stainless steel; meanwhile, the COD values of purified water were approaching to or less than 100 mg·L^-1, and the phenol concentrations in the purified …

Calcium Zincate Prepared By Ball Mill Method, Sheng-Xian Li, Shuan-Bao Tian, Shao-Shan Zhu

Journal of Electrochemistry

Calcium zincate was prepared by ball milling method and the factors that influence its synthesis were investigated. The composition of the compound was Ca(OH)₂·2Zn(OH)_2^·2H₂O, which was verified by XRD and TG-DTA methods. The results of powder microelectrode and in simulated batteries showed that the material had excellent cyclic performance.

Influence Of Rare Earth Oxide On The Performance Of Secondary Zinc Electrodes, Xian-Ling Meng, Hua-Bin Yang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

Influence of La(OH)₃ or Ce(OH)₃ in secondary zinc electrode was investigated by the cyclic voltammetry, potentiodynamic polarizationand potentiostatic polarization tests and influence of La₂O₃ or CeO₂ in the charge/discharge performance of Zn/Ni battery was studied by galvanostatic charge/discharge experiment. The results showed that the film of rare earth hydroxide prevented the zincate species from transferring toward solution, enhanced hydrogen overpotential and decreased thecorrosion current density (i_corr), and therefore inhibited zinc corrosion. The potentiostatic polarization results at100mV overpotential showed that La(OH)₃ or Ce(OH)₃ oated on the zinc electrode effectively suppressed the …

The Fabrication And Electrochemical Studies On Carbon Nanotube Array Electrodes, Quan-Yong Gao, Jing Zhang, Yong Yang

Journal of Electrochemistry

An improved technique for fabrication of carbon nanotube array electrodes has been proposed in this work. Firstly, carbon nanotubes (CNs) array electrodes were prepared by combsination of Chemical Vapor Decomposition (CVD) method and sputtering techniques in anodized aluminum oxide (AAO) membrane. The CNs/AAO was immersed into HF solution to remove the barrier layer. Controlling the immersing time, the CNs array electrodes with different length contacted with electrolyte can be prepared. The morphology of CNs array electrodes was observed by SEM. The electrochemical properties of CNs array electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Cyclic voltammetric curves of …

Fabrication And Studies Of A Novel Ag/Agcl Reference Electrode In High Temperature Molten Chloride Salts, Pei Gao, Xian-Bo Jin, Di-Hua Wang, Xiao-Hong Hu, Zheng Chen

Journal of Electrochemistry

A new method for the easy fabrication of a stable and long life silver/silver chloride reference electrode in molten chloride salts is described in this paper. The method is based on the fact that simply placing the silica glass in molten NaCl or its vapour in the presence of oxygen resulted in satisfactory conductivity for sodium ion and possibly calcium ion in the material.The performance of such made electrode has been investigated in a few typical chloride systems at temperatures ranging from 400 to 900℃. Due to the wholly sealed construction, the reference electrode is stable, temperature-reversible, contamination free to …

Using Neural Networks To Identify The Effect Of Construction Factors On The Cost Of Reinforced Concrete Elements, Ahmed Aly El-Sotouhy

Archived Theses and Dissertations

No abstract provided.

Engineering Tools For Variable Stiffness Vibration Suppression And Isolation, Michael F. Winthrop

Theses and Dissertations

With the advent of smart materials, the concept of semi-active control or dynamic control of stiffness and/or damping for vibration control of structures has become practical and has seen limited use. Semi-active control has advantages over active and passive control methods, since it provides almost as much capability as active control while requiring much less power. Its main disadvantage is its inherent nonlinearity, greatly complicating engineering design. The purpose of this research is to extend semi-active control vibration isolation tools and methods considering space launch and on-orbit systems.

Me-Em 2005 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Overview, Mission, and Vision
• Comments on the Strategic Plan
• Enrollment and Expenditure Data
• Professional Advisory Committee
• Faculty & Staff
• Students
• Alumni
• Entrepreneurs
• Resources
• Graduates
• Publications

Medical Technology: Contexts And Content In Science And Technology, Michael A. De Miranda, Mark Doggett, Jane T. Evans

Architectural and Manufacturing Sciences Faculty Publications

No abstract provided.

Rf-Sputter Fabrication Of Magnetic Garnet Thin Films And Simulation Modeling For 1-D Magnetic Photonic Crystal Waveguide Devices, Haichun Yang

Dissertations, Master's Theses and Master's Reports - Open

One dimensional magnetic photonic crystals (1D-MPC) are promising structures for integrated optical isolator applications. Rare earth substituted garnet thin films with proper Faraday rotation are required to fabricate planar 1D-MPCs. In this thesis, flat-top response 1D-MPC was proposed and spectral responses and Faraday rotation were modeled. Bismuth substituted iron garnet films were fabricated by RF magnetron sputtering and structures, compositions, birefringence and magnetooptical properties were studied. Double layer structures for single mode propagation were also fabricated by sputtering for the first time.

Multilayer stacks with multiple defects (phase shift) composed of Ce-YIG and GGG quarter-wave plates were simulated by the …

Electronic Commerce Negotiation In A Supply Chain Via Constraint Evaluation, R. Wilhelm, B. Chu, R. Sun

Department of Mechanical and Materials Engineering: Faculty Publications

Negotiation is of critical importance in e-commerce applications where the supply chain is dynamic and reconfiguring. In this research supply chain negotiation problems are addressed as constraint-satisfaction problems. In general each negotiation is handled in the largest scope possible to avoid the suboptimality that can result from many local solutions. This global approach, however, must be balanced with time constraints that apply in e-commerce supply chain execution. In this paper, we describe a new approach for e-commerce supply chain negotiation via constraint evaluation. As well, results from prototype software, distributed across the internet, are discussed. Beyond the general formulation, we …

Managing The Transformation Of System Of Systems Engineering, Samuel F. Kovacic, Andres Sousa-Poza

Engineering Management & Systems Engineering Faculty Publications

SOSE methodologies exist that support engineering difficult and disparate systems with a technical solution. However, from literature it is apparent that there is a need for a formal methodology and methods that govern engineering of System of Systems (SOS) beyond the technical solution. This paper presents some of the current thinking being undertaken at NCSOSE (National Centers for Systems of Systems Engineering), on what is driving the development of SOSE, and a hypothesized solution to this problem. The purpose is to offer a different approach for resolving complexity within a situation. The paper concludes with an initial derivative of a …

Adaptive Voip Playout Scheduling: Assessing User Satisfaction, Miroslaw Narbutt, Andrew Kelly, Liam Murphy, Philip Perry

Articles

Delay and packet loss dramatically affect the quality of a voice-over-IP (VoIP) call and depend on the playout buffer scheme implemented at the receiver. The choice of playout algorithm can’t be based on statistical metrics without considering the perceived end-to-end conversational speech quality. The authors present a method for evaluating various playout algorithms that extends the Emodel concept by estimating user satisfaction from time-varying transmission impairments. This article evaluates several playout algorithms and shows a correspondence between their results and those obtained via statistical loss and delay metrics.

A Project Improvement System For Effective Management Of Construction Projects, Shahriyar Mojahed

LSU Doctoral Dissertations

The concept of construction productivity began in the early 20th century with a series of time and motion studies to improve bricklaying operations. A substantial number of subsequent studies focused on repetitive tasks and automation of the manufacturing operations and subsequently benefited manufacturing more than the construction industry. There has been a lack of studies for productivity improvement in the construction industry. Building upon the available body of knowledge as it related to productivity of manufacturing and construction industries, this study focused on developing a project improvement system for effective management of construction projects. Development of the system included a …

A Tablet Pc Application For Construction Site Safety Inspection And Fatality Prevention, Prabhu Sunkara

LSU Master's Theses

Construction industry accounts for the largest number of occupational injuries and fatalities every year. Occupational Safety and Health Administration (OSHA) is an organization responsible for regulating and enforcing standards for various occupations to ensure safe working conditions including construction industry. As an OSHA requirement, every construction employer should employ a safety program that involves both training of the employees and frequent site inspections. OSHA has provided an online ‘construction eTool’ as a training tool which also aids in the development of safety inspection procedures. Traditionally, safety inspections are paper based and usually designed to address a specific work area or …

Purification And Structural Characterization Of Caged Dna Oligonucleotides, Brendan Michael Mcadams

LSU Master's Theses

“Cage” molecules reversibly block the bioactivity of a target substrate molecule by a photolyzable covalent bond formed at a functional site of the target molecule. The attachment of cage molecules to DNA oligodeoxynucleotides (ODNs) to transiently block bioactivity, and site-specific restoration of bioactivity using targeted light exposure, would enable a new method of control for use in gene therapy, molecular/DNA computing, molecular biology, and drug delivery. The reaction of the cage molecule 1-(4,5-dimethoxy-2-nitrophenyl)diazoethane (DMNPE) with DNA ODNs in an batch reaction yields a mixture of products with varying degrees of caging. Purification and verification of the hypothesized site of DMNPE …

The Electrodeposition And Property Study Of Nickel-Rhenium Alloy, Shirong Wen

LSU Master's Theses

The electrodeposition of nickel-rhenium alloys from Ni(II) and Re(VII) solution was studies in an aqueous acidic solution. Different plating current density and pH have been carried out, and the effect of them on the composition of the deposited Ni-Re alloy was studied. Wavelength-dispersive spectrometer (WDS) was used to measure the composition of Ni-Re alloy. The thermal stability of nickel-rhenium alloy system has been investigated. Differential scanning calorimetry (DSC) tests have been conducted for the electroplated Ni-Re samples in order to find the possible heating initiated interactions at elevated temperatures. To investigate the thermal stability of Ni-Re alloys, the samples were …

Managing The Transformation Of System Of Systems Engineering, Samuel F. Kovacic, Andres Sousa-Poza

Engineering Management & Systems Engineering Faculty Publications

SOSE methodologies exist that support engineering difficult and disparate systems with a technical solution. However, from literature it is apparent that there is a need for a formal methodology and methods that govern engineering of System of Systems (SOS) beyond the technical solution. This paper presents some of the current thinking being undertaken at NCSOSE (National Centers for Systems of Systems Engineering), on what is driving the development of SOSE, and a hypothesized solution to this problem. The purpose is to offer a different approach for resolving complexity within a situation. The paper concludes with an initial derivative of a …

Influence Of Composition And Heat-Treatment On The Charge Transport Properties Of Poly(3-Hexylthiophene) And [6,6]-Phenyl C61-Butyric Acid Methyl Ester Blends, Jinsong Huang, Gang Li, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C₆₁-butyric acid methyl ester (PCBM) blends have been demonstrated to form highly efficient polymer photovoltaic devices. In this letter, the time-of-flight technique is used to investigate the influence of composition and heat treatment on charge transport properties of P3HT and PCBM blends. The transport of electrons and holes both display a transition from dispersive to nondispersive and return to dispersive again as the percentage of PCBM increases. A balanced mobility of both electron and hole is obtained at a composition of 1:1 weight ratio, and it is nearly independent of the electrical field in …

Effect Of Microstructure And Alloying Elements On The Resistance Of Fastener Grade Steels To Hydrogen Assisted Cracking , Nicholas E. Nanninga

Dissertations, Master's Theses and Master's Reports - Open

Fastener grade steels with varying alloy contents and heat treatments were employed to measure changes in resistance to hydrogen assisted cracking. The testing procedure compared notched tension specimens fractured in air to threshold stress values obtained during hydrogen charging, utilizing a rising step load procedure. Bainitic structures improved resistance by 10-20% compared to tempered martensite structures. Dual phase steels with a tempered martensite matrix and 20% ferrite were more susceptible and notch sensitive. High strength, fully pearlitic structures showed an improvement in resistance. Carbon content, per se, had no effect on the resistance of steel to hydrogen assisted cracking. Chromium …

Evidence Of Neotectonic Activity In Southwest Louisiana, Jordan Oliver Heltz

LSU Master's Theses

A methodology that combines high-resolution topographic mapping, field observations, subsurface evaluation, and geodetic data analysis has successfully located several fault-related geomorphic steps in an area of southwestern Louisiana once thought to be relatively devoid of such features. Comparison of height differences of benchmarks straddling these suspected fault-related steps shows that vertical displacement rates on faults in the study area ranged from about 2 mm/yr to as much as 6 mm/yr during the 1960’s and 1970’s. However, leveling data obtained as recently as January 2005 reveals that the majority of these faults are currently moving at rates of less than 1 …

Transport And Kinetics Of Aromatic Hydrocarbons Into Micron-Sized Liquid Droplets: With Applications To Atmospheric Chemistry, Suresh Raja

LSU Doctoral Dissertations

In the natural process of wet deposition, gas-water interfaces play an important role in the transport of chemical contaminants in the atmosphere via fog, rain and cloud drops. Evidences from several other works point out deviations in gas-liquid partitioning as predicted by Henry’s law. Uptake and mass transfer of benzene, naphthalene, and phenanthrene was chosen to study in a falling droplet train apparatus. Higher droplet-to-vapor partition constant (KDV) was noted for diameters less than 200ìm and was attributed to surface adsorption and accumulation. Mass transfer of phenanthrene was dependent on gas-phase diffusion and mass accommodation at the interface, while the …

Development Of High Performance Hybrid Syntactic Foams: Structure And Material Property Characterization, Rahul R. Maharsia

LSU Doctoral Dissertations

Syntactic foams are light weight particulate composites that use hollow particles (microballoons) as reinforcement in a polymer resin matrix. High strength microballoons provide closed cell porosity which helps in reducing weight of the material. Due to their wide range of possible applications such as in aerospace and marine structures, it is desirable to modify the physical and mechanical properties of syntactic foams as per the requirements of an application. Various filler materials can be used to modify the foam microstructure to attain these desired properties. Compression tests have revealed that high density syntactic foams demonstrate poor damage tolerance and low …