Engineering Science and Materials Commons^™

Structural Design And Analysis Of A Rigidizable Space Shuttle Experiment, Raymond G. Holstein Iii

Theses and Dissertations

AFIT is in the process of designing a Space Shuttle experiment designated as the Rigidized Inflatable Get-Away-Special Experiment (RIGEX) to study the effects of microgravity on the deployment of rigidizable composite structures. Once in space, the experiment will inflate and rigidize three composite structures and perform a vibration analysis on each by exciting the tubes using piezoelectric patches and collecting data via an accelerometer. This paper presents the structural and vibration analysis of the RIGEX assembly and inflatable composite tubes using ABAQUS Finite Element Analysis (FEA) software. Comparison of the analysis has been carried out with Eigenvalue/Eigenvector experimentation by means …

Optimization Process For Configuration Of Flexible Joined-Wing, Cody C. Rasmussen

Theses and Dissertations

This study established a weight optimized configuration design of a joined-wing sensor-craft. The joined-wing aircraft concept fulfills a proposed long-endurance surveillance mission that contains an antenna structure embedded in the wing skin. The analysis was completed utilizing structural optimization, aerodynamic analyses, and response surface methodology. A sample of 62 joined-wing configurations were weight optimized. Each optimized structure was determined through a change of skin, spar, and rib thickness in the wing box by determining trimmed maneuver and gust conditions for critical flight mission points. Since the joined-wing concept has non-linear deformation characteristics, the structural optimization used both strain and buckling …

Vibrometric Detection Of Beam Damage Due To Inclusions, Aaron J. Reifsnyder

Theses and Dissertations

The Air Force Institute of Technology, in conjunction with the Structural Health Monitoring branch of the Air Force Research Laboratory, is researching methods of determining effects of notch location and size on beam structures using modal frequency analysis. This thesis explores the ability to detect included notches of varying magnitudes and locations within the frequency domain of an isotropic cantilever beam. A series of experiments employing centerline-notched 2024 T3 and 2024 0 aluminum beams was used to determine whether natural frequency measurement in beam structures is a valid mechanism for damage detection. Each specimen was excited by a strain actuator …

An Electromagnetic Tool For Damping And Fatigue Analysis, Todd M. Hoover

Theses and Dissertations

An automated test system was developed by the USAF Turbine Engine Fatigue Facility (TEFF). This system was initially designed to reduce the time and manpower required to characterize damping treatments. It is based on a digitally controlled environmental chamber with automated data acquisition and processing. Several outputs are available including identification of natural frequencies, modal damping ratios from the acquired frequency responses, and changes in damping with response amplitude; however, the TEFF additionally desires the capability to study fatigue under a free boundary condition. The system consists of a test specimen suspended by a pendulum to closely simulate free boundary …

Effect Of A Variable Contact Load On Fretting Fatigue Behavior Of Ti-6al-4v, Andrew J. Jutte

Theses and Dissertations

Effects of a variable contact load on the high cycle fretting fatigue behavior of Ti-6AL-4V were investigated. Experimental tests were performed using a new test setup capable of applying a contact load varying in amplitude, frequency, and phase and independently measuring shear forces on opposite sides of a specimen. Finite element analysis (FEA) of experimental and idealized loading conditions was performed and local mechanistic parameters and the Modified Shear Stress Range (MSSR) fatigue parameter were determined. Correlations between contact width, slip amplitude, fatigue life and a variable contact load were established with variable contact loading shown to have a damaging …

The Evaluation Of The Damping Characteristics Of A Hard Coating On Titanium, Christopher M. Blackwell

Theses and Dissertations

Engine failures due to fatigue have cost the Air Force an estimated $400 million dollars per year over the past two decades (Garrison, 2001). Damping treatments capable of reducing the internal stresses of fan and turbine blades to levels where fatigue is less likely to occur have the potential for reducing cost while enhancing reliability. This research evaluates the damping characteristics of magnesium aluminate spinel, MgO+Al₂O₃, (mag spinel) on titanium plates. The material and aspect ratio were chosen to approximate the low aspect ratio blades found in military gas turbine fans. The plates were tested with …

Progress In Research For Biofuel Cell, Yue Bao, Xia-Qin Wu

Journal of Electrochemistry

In this article, research progresses of the biofuel cell in recent years were summarized. The operation principle and classification of the biofuel cells were described. The role of the mediator for promoting electron transfer in biofuel cells and the techniques for improving the electric properties of biofuel cells, such as output potential, were discussed with some attracting research instances. Finally, the choke points for research of biofuel cell were explored, and the application prospect of biofuel cells was forecasted.

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma

Journal of Electrochemistry

In this paper, Pt/CNTs catalyst was prepared and its electrocatalytic property was studied by obtaining cycling voltammetry curves (C-V) and Tafel curves. In addition, the XRD,XPS and TEM tests were carried out to determine the structure and composition of the catalysts. It can be found that the platinum loading has been increased significantly using a carbon nanotubes support. Dispersion of Platinum was better and gave more active sites. The electrochemical characteristic of Pt/CNTs was also more desirable than that of Pt/C catalys t(Johnson Matthey). In conclusion, carbon nanotubes can played a conspicuous role in "electrogenerative" processes of PEMFC hydrogenation reactor.

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian

Journal of Electrochemistry

The monocrystalline metal nanowire arrays were prepared by using a two-step AC electrodeposition in porous anodic aluminum oxide (AAO) template. The growth mechanism of nanowires was discussed. As a result, it has been found that the second voltage pulse has a considerable effect on the pore-filling ratio, the uniformity and the crystal structure, whereas the initial voltage pulse affects only the pore-filling ratio. Using the two-step AC electrodeposition, a highly ordered monocrystalline metal nanowire arrays with a pore-filling ration above 95% can be easily obtained.

The Interaction In Doping Lithium Of Carbonaneous Anode In Lithium Ion Battery, Chang-Guo Chen, Hong-Min Zhang, Jia Chen, Dan-Mei Yu

Journal of Electrochemistry

The quantum chemical DV-X_α method was used to calculate the lithium-doped models from one-Li-dopant to LiC₆ and LiC₂. It was found that Li⁺ has an tendency to attract electrons from the carbon plane through the C₆ hexagons lying above or below it by the graph of charge-density difference. It was shown that LiC₆ can exist steadily,while LiC₂ can not exist steadily.

Study On Determination Of Iodine Ion At Chitosan Modified Glassy Carbon Electrode, Bin Liu, Xiang-Ying Sun, Jin-Rui Xu

Journal of Electrochemistry

In this paper, a chitosan modified glassy carbon electrode was prepared by the method of covalent-bond reaction, and the anodic stripping voltammetric characteristics of iodine on the modified electrode was studied. The results showed that the modified electrode has higher adsorption and selectivity for I^- , and the sensitivity for I^-  has been much improved in 0.1 mol·L^-1 KH₂PO₄ solution (pH=4.0). The anodic stripping peak current of I^- on the modified electrode varied linearly with I^-  concentration in the range of 2.0×10^-6～2.0×10^-3 mol·L^-1, and the detection limit …

Formation And Characterization Of Water-Repellent Nano Tio2 Coating And Studying Its Anticorrosion Property, Guang-Xia Shen, Yi-Cong Chen, Chang-Jian Lin

Journal of Electrochemistry

Using ethyl acetoacetate (EAcAc) as a chelating agent, ultra fine TiO₂ sol is prepared. Nano-TiO₂ coatings are deposited on the 316L stainless steel by the dip-coating. Hydrothermal post-treatment leads to crack-free coatings. Meanwhile, the surface struture and properties was optimized. Self-assembly of Hetadecafluorodecyltrimethoxysilane (FSA-13) fabricates hydrophobic layers on the surface of the nano-TiO₂ coatings. Particle sizes of TiO₂ sol was analysed by zeta pals potential analysis, and surface morphology, structure and properties was characterized by contract angle instrument, XRD, and SEM technologies. The results have shown that the surface of coatings is porous, with approx. 375 …

Study Of Electrochemical Properties Of The Hydride Alloy Electrode Zrcr0.4Mn0.2V0.1Co0.1Ni1.2 At High Temperature, Song Li, Shi-Jun Ji, Jun-Cai Sun

Journal of Electrochemistry

Electrochemical properties of the hydride alloy electrode ZrCr_0.4Mn_0.2V_0.1Co_0.1Ni_1.2 at the different temperature have been investigated. The results showed that the alloy electrodes possessed the maximum discharge capacities 336 mAh/g and 298 mAh/g at 25 ℃ and 70 ℃ respectively. The activation process of the alloy at 70 ℃ became faster, and the alloy reached its maximum capacity in less than 4 cycles, while in 13 cycles at 25 ℃. The high rate capability increased from 55 % at 25 ℃ to 71% at 70 ℃ at 300 mA/g. It was worth …

Electrochemical Synthesis Of Ferrate(Vi) By Anodic Oxidation, Jia-Ju Xu, Jian-Ming Wang, Wei-Hua Yang, Cheng Chen, Jian-Qing Zhang

Journal of Electrochemistry

The ferrate(Ⅵ) was synthesized by electrochemical anodic oxidation. The effects of preparation conditions on the current yield of ferrate(VI) synthesis have been studied in this work. The experimental results showed that grey cast iron as an anodic material is suitable for electrochemical synthesis and NaOH solution as an electrolyte results in a higher current yield than KOH solution. The highest current yield was obtained at a current density (4.54) mA·cm^-2, temperature 20 ℃ and 14 mol·dm^-3 NaOH. In this case, a current yield of 68.5% was obtained by electrolysis for 1 h.

Substrates Made By Electrodeposition For Measuring Electrical Properties Of One Dimensional Nanomaterials, Jin-Xuan Liu, Juan Xiang, Zhong-Qun Tian, Bing-Wei Mao

Journal of Electrochemistry

A method to prepare alternating conducting/insulating substrates by electrodeposition-oxidation was established to facilitate I-E measurements of one-dimensional nanomaterial by CT-AFM. The prepared Au/CuO and HOPG/CuO substrates showed low roughness as well as high uniformity of the alternating conducting/insulating structure, Qualitative I-E measurements were performed on a single carbon nanotube attached to the two above-mentioned substrates, both showing metallic characteristics at room temperature and in air.

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu

Journal of Electrochemistry

The electroreduction mechanism of oxalic acid on Pb electrode in Na₂SO₄ solution were investigated using high scan rate cyclic voltammetry and chronoamperometry. The dynamic parameters for the first step electron transter reaction of oxalic acid electroreduction by were determined. The corresponding reduction peak potentials of oxalic acid, glyoxylic acid and glycolic acid in the cyclic voltammogranis obtained in the same condition were compared, and the intermediate reduction products of oxalic acid were suggested. The results showed that oxalic acid is weakly absorbed on the lead electrode.

Electrochemical Character Of Water Containing Gel Electrolyte And Its Preliminary Examination In Lithium Water Cell, Jing-Dong Liu, Wen-Ji Wang, Xin-Zheng Yi

Journal of Electrochemistry

AC impedance technique has been used to characterize the system of poly(methyl acrylic acid)-poly(methyl acrylic lithiumate)-glycerol (referred to as GPE).The results showed that the conductivity of GPE increased with increasing both temperature and its water content.The glass transition temperature of GPE polymer could be lowered by water. Its conducting characteristic was just like liquid electrolyte,The electrolysis of GPE was almost the same as the electrolysis of water. Its composition voltage was about 1.50V. The GPE has been used to manufacture lithium water cell. When the graphite was used as cathode, the cell could discharge continuously for 2 hours under constant …

Electrodeposition Nanolaminated Growth Of Zinc, Ying Cao, Tian-Hui Shen, Jing-Yuan Yao, Gui-Fu Ding

Journal of Electrochemistry

Nanolaminated growth of the electrodeposition of zinc was studied. The structure and size of crystalline in zinc coatings were investigated by using FEG-TEM and XRD. The corrosion tests of the zinc deposition and the Coatings-Neutral salt spray test were performed, the capability in corrosion resistance of the nanolaminated growth was better than that of others.

Bar Clamp Having Ergonomic Handle, M. Susan Hallbeck, Myung-Chul Jung

Department of Mechanical and Materials Engineering: Faculty Publications

The present invention generally relates to a handle assembly for a hand operable bar clamp having a fixed jaw, a movable jaw and a drive for translating the movable jaw towards the fixed jaw. The assembly includes a handgrip and a trigger handle. The handgrip having an elongated rear portion has a generally rounded surface and being contoured to complement the natural transverse curve pf a human palm. The trigger handle is pivotal with respect to the handgrip. The trigger handle included an elongated front portion having a rounded front surface and being contoured to complement the natural palmer curve …

Me-Em 2004 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Overview
• Mission, Vision, and Strategic Plan
• Enrollment and Expenditure Data
• Faculty & Staff
• Industrial Advisory Committee
• Students
• Academic Programs
• Alumni
• Donations
• Contracts & Grants
• Graduates
• Publications

Design And Fabrication Of Electromagnetic Micro-Relays Using The Uv-Liga Technique, John Dalton Williams

LSU Doctoral Dissertations

This dissertation reports a research effort to microfabricate an electromagnetic relay for power applications using a multilayer UV-LIGA process. A mechanically wrapped coil was used and very simple design for the magnetic circuit was adopted to increase the design flexibility and performances. The broad material selection and the capability of making high aspect ratio microstructures of the UV-LIGA make the technology best suited for fabricating microelectromechanical power relays. Fabrication of the device required significant advances in the optical lithography of SU-8 negative photoresist. Research proved that aspect-ratios up to 40:1 in isolated open field structures of thickness between 1 and …

Processing, Microstructure And Mechanical Behavior Of Nanocomposite Multilayers, Zuqiang Qi

LSU Doctoral Dissertations

Nanoscale multilayer coatings have high potential for numerous engineering applications because they can exhibit enhanced properties due to nanoscale effects and combine different properties from individual components. At present, scale effects on the mechanical behavior of multilayers are not well understood. Three multilayer nanocomposite systems, namely Al/Al2O3, Ti/TiN, and Cr/a-C, have been synthesized by using a dual-gun e-beam physical vapor deposition, to investigate the effect of layer thickness, the nature of components and their microstructures on the mechanical behavior. The deposited Al and Ti nanolayers were found to have polycrystalline fcc and hcp structure, respectively, the Cr and TiN layers …

Synthesis, Structure, And Tribological Behavior Of Nanocomposite Dlc Based Thin Films, Varshni Singh

LSU Doctoral Dissertations

Diamond-like carbon (DLC) films possess a combination of attractive properties and have been largely employed to modify the tribological behavior of materials. Nanocomposite, metal-containing DLC films are the new generation of these coatings providing tremendous potential to modify and tailor their properties expanding their applications in the field of nanotechnology. The present study investigates nanoscale effects on the tribological behavior of composite nanostructured DLC-based films and functional coatings. Three aspects were studied: (i) effect of Cr interlayer on a functionally gradient substrate; (ii) nanoparticulate Cr-containing DLC (Cr-DLC) films; and (iii) nanocomposite multilayered Cr/DLC coatings. Intensified plasma assisted nitriding produced a …

Evolution Of Base Substitution Gradients In Primate Mitochondrial Genomes, Sameer Raina

LSU Master's Theses

The availability of large amounts of genetic data from the mitochondrial DNA of species has created an unprecedented opportunity for the study of evolutionary processes. Being our closest relatives on the evolutionary tree the primates are a prime candidate for the study of evolutionary processes. The availability of large amounts of genetic data from the primates allows us to study and compare results from different phylogenetic reconstruction methods and to study and trace rudimentary evolutionary processes within the primate lineage. The evolutionary process studied here is the response of the nucleotide frequency ratios to single-strandedness of sites during mitochondrial DNA …

An Understanding Of The Application Of Research Methods In Engineering Management, Andres Sousa-Poza, Rafael Landaeta, Leonardo Bedoya, Ipek Bozkurt, Yaneth Correa

Engineering Management & Systems Engineering Faculty Publications

In this article, the use of research methods in the field of Engineering Management is analyzed. For this study, a database was formed by using articles from three journals in the Engineering Management field: the Engineering Management Journal (EMJ), the IEEE Transactions on Engineering Management and the Journal of Engineering and Technology Management (JETM). Articles written between 1999 and 2003 were analyzed and an Engineering Management research position map was developed to describe holistically the research methods being used in Engineering Management. No judgment on the Engineering Management field per se was undertaken as a result of this study. Instead, …

Multifunctional Nanocomposite Co-Containing Diamondlike Carbon Thin Films, Fengli Wang

LSU Doctoral Dissertations

Metal-containing, hydrogenated carbon films (Me-a-C:H) is a special class of nanocomposite films of particular interest since they can be multifunctional through the synergistic interaction of their individual components. Thus, nanocomposite thin films possess high potential in a wide field of engineering applications, especially in small scale devices. A series of multifunctional nanocomposite Co-a-C:H thin films have been synthesized by a hybrid chemical vapor deposition (CVD) and physical vapor deposition (PVD) process to uncover the relationship between synthesis, microstructure and properties. The effects of deposition parameters on the microstructural evolution and properties have been systematically studied. The results showed that the …

Morphological Evolution And Instabilities Of Solid Thin Films And Wires, Wanxi Kan

LSU Doctoral Dissertations

This dissertation can be divided into four parts. In part I (Chapter 2), the diffusion controlled growth of multiple compound phases is studied with the nonlinear Kirkendall effect included. This part analyzes the growth of N compound phases. The method of finding intrinsic diffusion coefficients from only the positions of interfaces is found for two layers. In addition, the asymptotic analysis valid for small concentration gradients is applied to the “multi-foil” method of measuring intrinsic diffusion coefficients and yields an analytic solution for the displacement curve. A bounded solid film on a substrate can breakup from the edge into islands …

Modeling The Effects Of Rainfall Intensity And Deep Chiseling On Infiltration And Runoff Within Drainmod For Alluvial Soils, Daniel Nyabiba Moriasi

LSU Doctoral Dissertations

Accurate hydrologic models are needed to aid engineers and researchers design, install and evaluate efficient and cost-effective agricultural water management systems to reduce risks associated with food production, and to reduce soil erosion and water pollution. One model used for the alluvial soils of Louisiana is DRAINMOD. This model does not accurately predict infiltration and runoff for the crusting-prone alluvial soils of Louisiana. The main goal of this study was to modify the current DRAINMOD model to incorporate the effects of rainfall intensity and deep chiseling to improve its estimation of infiltration and surface runoff. The second goal was to …

Optimization Of A Skewed Logistic Distribution With Respect To The Kolmogorov-Smirnov Test, James Charles Finney

LSU Doctoral Dissertations

The four-parameter kappa distribution (Hosking 1994) was analyzed with respect to the various possible shapes of the probability density function. The general form for the cumulative distribution function when both h and k are non-zero is: F(x) = { 1 - h [ 1 - k ( x - ξ ) / α ]^1/k }^1/h. The parameters h and k work together to define the function's shape, ξ affects location, and α is the scale parameter. A method of selecting parameters to minimize the Kolmogorov-Smirnov test statistic, D, was developed. The technique was first described for the …